there are some strange machines that seem to need this.
o delete bogus comment.
o don't use the the bios for read/writing config space. They interact badly
with SMP and being called from ISR. This brings -current in line with
-stable.
# make the latter #ifdef on USE_PCI_BIOS_FOR_READ_WRITE in case we
# need to go back in a hurry.
These are still unknown name but these are working as well
as the other ServerWorks chipset.
Description strings should be corrected when the chipsets
are known.
MFC after: 1 week
route interrupts if the child bus is described in the PCIBIOS interrupt
routing table. For child busses that are in the routing table, they do
not necessarily use a 'swizzle' on their pins on the parent bus to route
interrupts for child devices. If the child bus is an embedded device then
the pins on the child devices can be (and usually are) directly connected
either to a PIC or to a Interrupt Router. This fixes PCIBIOS interrupt
routing across PCI-PCI bridges for embedded devices.
IRQ for an entry in a PCIBIOS interrupt routing ($PIR) table.
- Change pci_cfgintr() to except the current IRQ of a device as a fourth
argument and to use that IRQ for the device if it is valid.
- If an intpin entry in a $PIR entry has a link of 0, it means that that
intpin isn't connected to anything that can trigger an interrupt. Thus,
test the link against 0 to find invalid entries in the table instead of
implicitly relying on the irqs field to be zero. In the machines I have
looked at, intpin entries with a link of 0 often have the bits for all
possible interrupts for PCI devices set.
not the 'entry' member. The entry point is formed from both a base and
a relative entry point. 'entry' is that relative offset. It is perfectly
valid to have an entry point with a relative offset of 0. PCIbios.ventry
is the virtual address of the entry point that takes both 'base' and
'entry' into account, thus it is the proper variable to test to see if we
have an entry point or not.
identify this gadget on the CPUID result alone, so I intend to activate
the necessary magic (i8254 frequency for instance) for it based on the
precense of the on-chip host to PCI bridge.
Don't require pin be non-zero before we map bogus intlines, always do it.
This fixes a number of problems on HP Omnibook computers.
Tested/Reviewed by: Brooks Davis
2, but that's not the case. This fixes the case where there were slots
in the PIR table that had no bits set, but we assumed they did and used
strange results as a result.
o Map invalid INTLINE registers to 255 in pci_cfgreg.c. This should allow
us to remove the bogus checks in MI code for non-255 values.
I put these changes out for review a while ago, but no one responded
to them, so into current they go.
This should help us work better on machines that don't route
interrupts in the traditional way.
MFC After: 4286 millifortnights
older PCI BIOSes hate this and this leads to panics when it is done. Also,
assume that a uniquely routed interrupt is already routed. This also
seems to help some older laptops with feable BIOSes cope.
This typo keeps us from properly routing an interrupt for CardBus
bridges on this machine. So, now we look for $PIR and then _PIR to
cope. With these changes, the Libretto L1 now works properly.
Evidentally, the idea comes from patch that the Japanese version of
RedHat (or against a Japanese version of Red Hat), but my Japanese
isn't good enough to to know for sure.
Reported by: Hiroyuki Aizu-san <eyes@navi.org>
# This may be an MFC candidate, but I'm not yet sure.
Merge in the irq 0 detection. Add comment about why.
If we have irq 0, ignore it like we do irq 255. Some BIOS writers aren't
careful like they should be.
multiple times, others do. The last strategy, which was to assume
that already routed interrupts were good and just return them doesn't
work for some laptops. So, instead, we have a new strategy: we notice
that we have an interrupt that's already routed. We go ahead and try
to route it, none the less. We will assume that it is correctly
routed, even if the route fails. We still assume that other failures
in the bios32 call are because the interrupt is NOT routed.
Note: some laptops do not support the bios32 interface to PCI BIOS and
we need to call it via the INT 2A interface. That is another windmill
to till at later.
Also correct a minor typo and minor whitespace nits.
Strong MFC candidate.
and such was just a bad idea and one that users should be forced to
enable if they want it. This patch introduces a hw.pci.enable_pcibios
tunable for those people. This does not impact the pcibios interrupt
routing at all.
Approved by: peter, msmith
some bios vendors took it apon themselves to "censor" the
host->pci bridges from PCIBIOS callers, even when the caller
explicitly asks for them. This includes certain Compaq machines
(eg: DL360) and some laptops.
If we detect this, shut down pcibios and revert to using IO
port bashing.
Under -current, apcica does a better job anyway.
declarations of a variable of the same name. The one in the outer block
was unused and probably just slipped in at one point or another. This
silences a compiler warning.
- Move PCI core code to dev/pci.
- Split bridge code out into separate modules.
- Remove the descriptive strings from the bridge drivers. If you
want to know what a device is, use pciconf. Add support for
broadly identifying devices based on class/subclass, and for
parsing a preloaded device identification database so that if
you want to waste the memory, you can identify *anything* we know
about.
- Remove machine-dependant code from the core PCI code. APIC interrupt
mapping is performed by shadowing the intline register in machine-
dependant code.
- Bring interrupt routing support to the Alpha
(although many platforms don't yet support routing or mapping
interrupts entirely correctly). This resulted in spamming
<sys/bus.h> into more places than it really should have gone.
- Put sys/dev on the kernel/modules include path. This avoids
having to change *all* the pci*.h includes.
systems.
From the PR:
When 'probe.slot' is PCI_SLOTMAX (== 31) and 'probe.func' is 7,
call to 'pci_cfgread()' here and machine suddenly hangs up.
I don't know why... (or 450GX chipset's bug?)
PR: i386/20379
Submitted by: Masayuki FUKUI <fukui@sonic.nm.fujitsu.co.jp>
- Look for a hardwired interrupt in the routing table for this
bus/device/pin (we already did this).
- Look for another device with the same link byte which has a hardwired
interrupt.
- Look for a PCI device matching an entry with the same link byte
which has already been assigned an interrupt, and use that.
- Look for a routable interrupt listed in the "PCI only" interrupts
field and use that.
- Pick the first interrupt that's marked as routable and use that.
i386/isa/pcibus.c. This gets -current running again on multiple host->pci
machines after the most recent nexus commits. I had discussed this with
Mike Smith, but ended up doing it slightly differently to what we
discussed as it turned out cleaner this way. Mike was suggesting creating
a new resource (SYS_RES_PCIBUS) or something and using *_[gs]et_resource(),
but IMHO that wasn't ideal as SYS_RES_* is meant to be a global platform
property, not a quirk of a given implementation. This does use the ivar
methods but does so properly. It also now prints the physical pci bus that
a host->pci bridge (pcib) corresponds to.
Some have dual host->PCI bridges for the same logical pci bus (!), eg:
some of the RCC chipsets. This is a 32/64 bit 33/66MHz and dual pci
voltage motherboard so persumably there are electical or signalling
differences but they are otherwise the same logical bus.
The new PCI probe code however was getting somewhat upset about it and
ended up creating two pci bridges to the same logical bus, which caused
devices on that logical bus to appear and be probed twice.
The ACPI data on this box correctly identifies this stuff, so bring on
ACPI! :-)
pcib_set_bus() cannot be used on the new child because it is
meant to be used on the *pci* device (it looks at the parent internally)
not the pcib being added. Bite the bullet and use ivars for the bus
number to avoid any doubts about whether the softc is consistant between
probe and attach. This should not break the Alpha code.
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
the PnP probe is merely a stub as we make assumptions about some of this
hardware before we have probed it.
Since these devices (with the exception of the speaker) are 'standard',
suppress output in the !bootverbose case to clean up the probe messages
somewhat.
- Add support for using the PCI BIOS functions for configuration space
accesses, and make this the default.
- Make PNPBIOS the default (obsoletes the PNPBIOS config option).
- Add two new boot-time tunables to disable each of the above.
chipset to be probed & attached on newer Dell PowerEdge servers, such as
the 2400 and 4400.
Reviewed by: dfr, msmith, jlemon
Tested by: hnokubi@yyy.or.jp (in a previous incantation)
Approved by: jkh
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
host->pci bridge specifically, then add a pcib0 device on the motherboard
for the pci bus to hang off.
Requested by: Anders Andersson <anders@sanyusan.se>
Obtained from: dfr
as PCI->HOST bridges on my (440BX) box.
My change is to remove the test at the beginning entirely, letting the
switch on the device ID happen first. If the device ID is unknown, then
(in the default case) check for the generic PCIS_BRIDGE_HOST tag. This
should allow wierd cases (eg: wpaul's IMS VL bridge) to work by using the
id override. This strategy is more in line with the other PCI match
methods we use elsewhere,
I only have a limited testbed, but having my USB etc devices detected as
PCI->HOST bridges doesn't look good.
correctly. It has the following code:
if (class != PCIC_BRIDGE || subclass != PCIS_BRIDGE_HOST)
return NULL;
My 486 has an Integrated Micro Solutions PCI bridge which identifies
itself as subclass PCIS_BRIDGE_OTHER, not PCIS_BRIDGE_HOST. Consequently,
it gets ignored. In my opinion, the correct test should be:
if ((class != PCIC_BRIDGE) && (subclass != PCIS_BRIDGE_HOST))
return NULL;
That way the test still succeeds because the chip's class is PCIC_BRIDGE.
Clearly it's not reasonable to expect all host to PCI bridges to always
have a subclass of PCIS_BRIDGE_HOST since I've got one that doesn't.
This way the sanity test should remain relatively sane while still allowing
some oddball yet correct hardware to work. If somebody has a better way
to do it, go ahead and tweak the test, but be aware that
class == PCIC_BRIDGE and subclass == PCIS_BRIDGE_OTHER is a valid case.
While I was here, I also added an explicit ID string for the IMS chipset.
I also dealt with a minor style nit: it's bad karma not to have a default
case for your switch statements, but the one in this routine doesn't have
one. The default string of "Host to PCI bridge" is now assigned in a
default case of the switch statement instead of initializing "s" with the
string before the switch and then not having any default case.
It failed to recognize the PCI bus in a system that had only an
old chip-set (class code 000000) and a Cyclom multiport serial
card on PCI bus 0, but no VGA card or disk or network controller.
PR: i386/5300
Submitted by: Nickolay N. Dudorov <nnd@itfs.nsk.su>
Adjust the data port address by adding the two low order bits of
the register number. The address port takes only a word address
(i.e. ignores the two low order bits written to it).
mode 1. Omission of this bit makes all config register accesses fail in
on recent chip sets ...
(The problem was reported and debug output provided by: Steve Passe)
reality. There will be a new call interface, but for now the file
pci_compat.c (which is to be deleted, after all drivers are converted)
provides an emulation of the old PCI bus driver functions. The only
change that might be visible to drivers is, that the type pcici_t
(which had been meant to be just a handle, whose exact definition
should not be relied on), has been converted into a pcicfgregs* .
The Tekram AMD SCSI driver bogusly relied on the definition of pcici_t
and has been converted to just call the PCI drivers functions to access
configuration space register, instead of inventing its own ...
This code is by no means complete, but assumed to be fully operational,
and brings the official code base more in line with my development code.
A new generic device descriptor data type has to be agreed on. The PCI
code will then use that data type to provide new functionality:
1) userconfig support
2) "wired" PCI devices
3) conflicts checking against ISA/EISA
4) maps will depend on the command register enable bits
5) PCI to Anything bridges can be defined as devices,
and are probed like any "standard" PCI device.
The following features are currently missing, but will be added back,
soon:
1) unknown device probe message
2) suppression of "mirrored" devices caused by ancient, broken chip-sets
This code relies on generic shared interrupt support just commited to
kern_intr.c (plus the modifications of isa.c and isa_device.h).
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
(1) deleted #if 0
pc98/pc98/mse.c
(2) hold per-unit I/O ports in ed_softc
pc98/pc98/if_ed.c
pc98/pc98/if_ed98.h
(3) merge more files by segregating changes into headers.
new file (moved from pc98/pc98):
i386/isa/aic_98.h
deleted:
well, it's already in the commit message so I won't repeat the
long list here ;)
Submitted by: The FreeBSD(98) Development Team
is only used by the icu support modules and by a few drivers that know
too much about the icu (most only use it to convert `n' to `IRQn'). isa.h
is only used by ioconf.c and by a few drivers that know too much about
isa addresses (a few have to, because config is deficient).
#includes to get prototypes.
pci now uses a different interrupt handler type for interrupts that it
dispatches and the isa interrupt handler type for the interrupts that
it handles.
