This patch removes several redundant forward declarations
in i40e_fdir.c.
Fixes: a778a1fa2e4e ("i40e: set up and initialize flow director")
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The statistics queried by calling rte_eth_stats_get are zero when
the API is first called on the port. The root cause is because the
offset_loaded flag is not set correctly after device start.
This patch fixes this issue by resetting statistics at initialization
time. The resetting process will set offset_loaded flag.
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The position of register values within i40e register dumps is
supposed to reflect the register addresses. These were not being
correctly calculated.
Fixes: d9efd0136ac1 ("i40e: add EEPROM and registers dumping")
Signed-off-by: Remy Horton <remy.horton@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Some statistics were deprecated since release 2.1 (49f386542af4).
The last deprecated counter to be used was imcasts.
The VF loopback statistics are also removed as they are used only
in igb and duplicated in extended statistics.
The new counters should be added to extended statistics.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Issue:
when using the following CLI in testpmd to enable ipv6 TSO feature
(set --txqflags=0 in the testpmd command)
set verbose 1
csum set ip hw 0
csum set udp hw 0
csum set tcp hw 0
csum set sctp hw 0
csum set outer-ip hw 0
csum parse_tunnel on 0
tso set 800 0
set fwd csum
start
We will not get what we want, the ipv6 packets sent out from IXIA can be
received by i40e, but cannot forward to another port.
The root cause is when HW doing the TSO offload for packets, it does not only
depends on the context descriptor to define the MSS and TSO payload size, it
also need to know whether this packets is ipv4 or ipv6, we use
i40e_txd_enable_checksum to generate the related fields for data descriptor.
But PMD will not call i40e_txd_enable_checksum if only the TSO offload flag is
set. The reason why ipv4 works fine for TSO in testpmd csum mode is csum engine
will set the ip csum flag when the packet is ipv4 and TSO is enabled but
will not set the flag for ipv6 and this flag will cause the
i40e_txd_enable_checksum to be invoked. For both the cases the TSO flag will be
set, so we need to use TSO flag to trigger the i40e_txd_enable_checksum.
The right logic here is we enable csum offload for both ipv4 and ipv6 when TSO
flag is set.
Fixes: e3f0151f ("i40e: enable Tx checksum only for offloaded packets")
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The issue is the VF's link speed kept as 10G and status always was up.
It did not change even the physical link's status changed.
This patch fixes this issue to make VF's link info consistent with
physical link.
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
This patch redesigns the API to set the link speed/s configuration
of an ethernet port. Specifically:
- it allows to define a set of advertised speeds for
auto-negociation.
- it allows to disable link auto-negociation (single fixed speed).
- default: auto-negociate all supported speeds.
A flag autoneg in struct rte_eth_link indicates if link speed was a
result of auto-negociation or was fixed by configuration.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Tested-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Tested-by: Beilei Xing <beilei.xing@intel.com>
Tested-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The speed capabilities of a device can be retrieved with
rte_eth_dev_info_get().
The new field speed_capa is initialized in the drivers without
taking care of device characteristics in this patch.
When the capabilities of a driver are accurate, the table in
overview.rst must be filled.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
The speed numbers ETH_LINK_SPEED_ are renamed ETH_SPEED_NUM_.
The prefix ETH_LINK_SPEED_ is kept for AUTONEG and will be used
for bit flags in next patch.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Define and use ETH_LINK_UP and ETH_LINK_DOWN where appropriate.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Calling rte_eth_dev_get_dcb_info to get dcb info from i40e
driver if VMDQ is disabled, results in a segmentation fault.
This patch fixes it by treating VMDQ and No-VMDQ respectively
when querying dcb information.
Fixes: 5135f3ca49a7 ("i40e: enable DCB in VMDQ VSIs")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Build log:
/root/dpdk/app/test-pmd/cmdline.c:6687:45: error: no member named
's6_addr32' in 'struct in6_addr'
rte_be_to_cpu_32(res->ip_value.addr.ipv6.s6_addr32[i]);
This is caused by macro "s6_addr32" not defined on FreeBSD and testpmd
swap big endian parameter to host endian. Move the swap action to i40e
ethdev will fix this issue.
Fixes: 7b1312891b69 ("ethdev: add IP in GRE tunnel")
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Bruce Richardson <bruce.richardson@intel.com>
The code uses "entry" in the next loop of LIST_FOREACH after calling free()
on it in i40e_res_pool_destroy().
Change to a safe way to free entry, which is similar with LIST_FOREACH_SAFE
in FreeBSD.
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Signed-off-by: Jiangu Zhao <zhaojg@arraynetworks.com.cn>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Issue:
When CONFIG_RTE_LIBTRE_I40E_RX_ALLOW_BULK_ALLOC=n in config file, there
will be a build error:
'i40e_recv_pkts_bulk_alloc' undeclared
Now DPDK i40e PMD uses the preprocessor to choose whether or not to define
the bulk recv functions, but for selection of the RX function, PMD only
depends on a C variable. This causes the inconsistency and leads to the
build error due to the bulk recv function not being defined.
Fixes: 8e109464c022 ("i40e: allow vector Rx and Tx usage")
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
This patch extends flow director to select vlan id as part of
filter's input set and program the filter rule with vlan id.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds missing VLAN bitmask for inner frame in case of
tunneling and fixes VLAN tags bitmasks for single or outer frame
in case of tunneling.
Fixes: 98f055707685 ("i40e: configure input fields for RSS or flow director")
Signed-off-by: Andrey Chilikin <andrey.chilikin@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch extends flow director to select more IP Header fields
as filter input set.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds a new function to set the fdir input set to default
when initialization.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
In this patch, flex payload is removed from valid fdir input set
values. This is because all flex payload configuration can be set
in struct rte_fdir_conf during device configure phase, which is
a more flexible way of setting this up.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
For the input set selection, Hash filter and Flow director shared
the same function, i.e. i40e_filter_inset_select.
For code readability, this patch replaces i40e_filter_inset_select
with two new functions: i40e_hash_filter_inset_select and
i40e_fdir_filter_inset_select for Hash filter and Flow director
respectively.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
When Linux PF and DPDK VF are used for i40e PMD, when a PF reset occurs,
an interrupt will go via adminq event to inform the VF of the reset.
A callback mechanism is introduced for the VF to allow it to invoke a
registered callback when PF reset happens.
Users can register a callback for this interrupt event using:
rte_eth_dev_callback_register(portid,
RTE_ETH_EVENT_INTR_RESET,
reset_event_callback,
arg);
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Currently, i40evf PMD uses a global static buffer to send virtchnl
commands to host driver. It is shared by multiple VFs.
This patch changed to allocate a virtchnl cmd buffer for each VF.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Add a new API rte_eth_dev_get_supported_ptypes to query what packet types
can be filled by a given device. The device should be already started or
its PMD RX burst function already decided, since the packet types supported
may vary depending on RX function.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Comment for "ierrors" counter says that it counts erroneous received
packets. But for some reason "imissed" counter is added to "ierrors"
counter in most drivers.
It is a mistake, because missed packets are obviously not received.
This patch fixes it.
Fixes: 70bdb18657da ("ethdev: add Rx error counters for missed, badcrc and badlen packets")
Fixes: 6bfe648406b5 ("i40e: add Rx error statistics")
Fixes: 856505d303f4 ("cxgbe: add port statistics")
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
This patch implemented the ops of adding and removing mac
address in i40evf driver. Functions are assigned like:
.mac_addr_add = i40evf_add_mac_addr,
.mac_addr_remove = i40evf_del_mac_addr,
To support multiple mac addresses setting, this patch also
extended the mac addresses adding and deletion when device
start and stop. Each VF can have a maximum of 64 mac
addresses.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
VEB switching feature for i40e is used to enable the switching between the
VSIs connect to the virtual bridge. The old implementation is setting the
virtual bridge mode as VEPA which is port aggregation. Enable the switching
ability by setting the loop back mode for the specific VSIs which connect
to PF or VFs.
VEB/VSI/VEPA are concepts not specific to the i40e HW, the concepts are
from 802.1qbg spec
IEEE EVB tutorial:
http://www.ieee802.org/802_tutorials/2009-11/evb-tutorial-draft-20091116_v09.pdf
VEB: a virtual switch can forward the packet based on the specific match
field.
VSI: a virtual interface connect between the VEB/VEPA and virtual machine.
VEPA: a virtual Ethernet port aggregator will upstream the packets from
VSI to the LAN port.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch fixes a typo in a comment in the definition of
the i40e_pf struct.
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Previously, DCB(Data Center Bridging) is only enabled on PF,
queue mapping and BW configuration is only done on PF.
This patch enables DCB for VMDQ VSIs(Virtual Station Interfaces)
by following steps:
1. Take BW and ETS(Enhanced Transmission Selection)
configuration on VEB(Virtual Ethernet Bridge).
2. Take BW and ETS configuration on VMDQ VSIs.
3. Update TC(Traffic Class) and queues mapping on VMDQ VSIs.
To enable DCB on VMDQ, the number of TCs should not be larger than
the number of queues in VMDQ pools, and the number of queues per
VMDQ pool is specified by CONFIG_RTE_LIBRTE_I40E_QUEUE_NUM_PER_VM
in config/common_* file.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
It removes the i40evf_set_mac_type() defined in PMD, and reuses
i40e_set_mac_type() defined in base driver.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
It adds base driver release information such as release date,
for better tracking in the future.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Several structures and macros are added or updated, such
as 'struct i40e_aqc_get_link_status',
'struct i40e_aqc_run_phy_activity' and
'struct i40e_aqc_lldp_set_local_mib_resp'.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
It adds the new AQ command and struct for managing a
thermal sensor.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
X722 supports Expanded version of TCP, UDP PCTYPES for RSS.
Add a Virtchnl offload to support this.
Without this patch VF drivers will not be able to support
the correct PCTYPES for X722 and UDP flows will not fan out.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds 7 new register definitions for programming the
parser, flow director and RSS blocks in the HW.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
RX control register read/write functions are added, as directly
read/write may fail when under stress small traffic. After the
adminq is ready, all rx control registers should be read/written
by dedicated functions.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
When updating a VSI, save off the number of allocated and
unallocated VSIs as we do when adding a VSI.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Fix the driver load failure with linking with some
PHY types, as the amount of time it takes for the
GLGEN_RSTAT_DEVSTATE to be set increases greatly on those PHY
types, which can lead to a timeout.
Fixes: 9aeefed05538 ("i40e/base: support ESS")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
In Multi-Function Mode (MFP) particularly when the PF VSI is set
in limited promiscuous mode, the HW switch was still mirroring the
outgoing packets from other VSIs (VF/VMdq) onto the PF VSI.
This sets a new bit to avoid above mirroring, and it is in limited
promiscuous on the PF VSI in MFP which is similar to default port
VSI.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds functions to blink led on devices using a new
PHY since MAC registers used in other designs do not work in
this device configuration.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Add the support code for calling the AdminQ API call
aq_set_switch_config.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
With the latest firmware, statistics gathering can now be enabled and
disabled in the HW switch, so we need to add a parameter to allow the
driver to set it as desired. At the same time, the L2 cloud filtering
parameter has been removed as it was never used.
Older drivers working with the newer firmware and newer drivers working
with older firmware will not run into problems with these bits as the
defaults are reasonable and there is no overlap in the bit definitions.
Also, newer drivers will be forced to update because of the change in
function call parameters, a reminder that the functionality exists.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch implements necessary functions related to port
mirroring features such as add/delete mirror rule, function
to set promiscuous VLAN mode for VSI if mirror rule_type is
"VLAN Mirroring".
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Add the use of the new shared MAC filter bit for multicast
and broadcast filters in order to make better use of the
filters available from the device.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch fixes a problem where the NVMUpdate Tool, when
using the PHY NVM feature, gets bad data from the PHY because
of contention on the MDIO interface from get phy capability
calls from the driver during regular operations. The problem
is fixed by adding a check if media is available before calling
get phy capability function because that bit is not set when
device is in PHY interaction mode.
Fixes: 842ea1996335 ("i40e/base: save link module type")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
The device capabilities were defined in two places, and neither had
all the definitions. It really belongs with the AQ API definition,
so this patch removes the other set of definitions and fills out the
missing item.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
The recently added proxy opcodes should be available only with
X722_SUPPORT, so move them into the #ifdef, and reorder these
to be in numerical order with the rest of the opcodes. Several
structs that were added are unnecessary, so they are removed
here.
Fixes: 788fc17b2dec ("i40e/base: support proxy config for X722")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
