This patch adds SW Low Power Link Up (LPLU) support for x550em PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds SFP+ dual-speed support.
82599 fiber link code was moved from ixgbe_82599.c to ixgbe_commom.c
for use by X550em, and the API was updated to support the common code
usage. SFP MAC link code is added to x550em.
Signed-off-by: Changchun Ouyang <changchun.ouyang@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The FEC (Forward Error Correction) feature can improve BER (Bit Error Rate)
but uses more power to do so. It also cannot be used with
EEE (Energy Efficient Ethernet).
EEE is an important feature, and we have no known BER issues, so FEC
is not needed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The I2C mux control relies on the SDP setting in the ESDP register
so it is necessary to restore the value after a MAC reset. So,
put the code in a function so it can be used in more than one place.
Fixes: d2e72774e5 ("ixgbe/base: support X550")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
On some hardware platforms, the CS4227 does not initialize properly.
Detect those cases and reset it appropriately.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The driver now needs to issue a firmware command to inform the
firmware that a driver is coming up. This prevents the possibility
of the firmware and the driver configuring the PHY at the same
time. Upon completion of the command, the firmware will no longer
be configuring the PHY.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
A retry count of 10 is likely to run into problems on X550 devices
that have to detect and reset unresponsive CS4227 devices. So,
reduce the I2C retry count to 3 for X550 and above. This should
avoid any possible regressions in existing devices.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Most I2C accesses take and release semaphores for each access. It's
also necessary to perform multiple I2C operations under the same
holding of the semaphore, so provide unlocked I2C methods for that
purpose.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
All bits in FDIRTCPM and FDIRUDPM are set to 1 when
ixgbe_fdir_set_input_mask_82599 is called. Not settings these bits will cause
TCP and UDP packets to be filtered out when NVGRE or VXLAN mode is enabled.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch moves the check of the return value from
ixgbe_start_hw_generic after the function is called.
Previously we had the code to disable relaxed ordering in
between, which seems a bit out of place.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Remove the redundant "from".
There's a typo in the code comment for FC end
of Frame Exception (FCEOFe/IPE), so fixed the typo.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Fix warning messages "cast to pointer from integer of different size" when
compiling DPDK in 32 bit with Mellanox PMD.
SGE addresses are 64 bit integers, converting them to pointers must be done
through uintptr_t to avoid compilation warnings when those have a different
size.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Fix NULL dereference if virtio control queue is not negotiated.
Signed-off-by: Damjan Marion <damarion@cisco.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Negotiate the virtio ring size. The host may allow for very large
rings but application may only want a smaller ring.
Conversely, if the number of descriptors requested exceeds the virtio
host queue size, then just silently use the smaller host size.
This fixes issues with virtio in non-QEMU envirionments.
For example Google Compute Engine allows up to 16K elements
in ring.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
Change the features from bit mask to bit number. This allows the
DPDK driver to use the definitions from Linux (yes the header
files already use a license compatiable with DPDK). This makes DPDK
driver handle future feature bit changes.
Get rid of double negative code in the feature bit intialization.
Instead just have a new define with the list of feature bits implemented.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
Don't attempt to set the MAC address table unless the host allows
it in feature negotiation. Also, don't return a value from mac_table_set
since all callers ignore the return value.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
If negotiation with host says that controlling Rx mode is
not supported, then don't try.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
Putting blank line between function and following conditional
just wastes screen space, and makes code less obvious.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Changchun Ouyang <changchun.ouyang@intel.com>
Upcoming drivers will need to be able to support other bus types.
This is a transparent change to how struct eth_driver is initialized.
It has not function or ABI layout impact, but makes adding a later
bus type (Xen, Hyper-V, ...) much easier.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Fix spelling errors in strings and comments.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Yong Wang <yongwang@vmware.com>
It wouldn't check the configured maximum packet length, and then
the scattered receiving function wouldn't be selected at all even
if it wants to receive a jumbo frame. The fix is to select the
correct RX function according to the configurations.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Remove 2 unneeded memset's. The info area is already cleared rte_eth_dev_info_get
and the statistics buffer is cleared by rte_eth_stats_get
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The stats area is already cleared before calling eth_stats_get().
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
On Fedora 22, with GCC 5.1, errors are reported due to array accesses
being potentially out of bounds. This commit fixes this by adding in an
extra bounds check to the loop counters, or, in the case of stats reset,
by blindly zeroing the whole array, rather than just the part that is in
use.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
On Fedora 22, with GCC 5.1, errors are reported due to array accesses
being potentially out of bounds. This commit fixes this by adding in an
extra bounds check to the loop counter.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
In DPDK, max_vfs means vf numbers created, not the max number vfs
the device supported.
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
To get device VMDQ info when only i40e VMDQ feature is enabled.
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
Move xenvirt PMD to drivers/net directory
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Move vmxnet3 PMD to drivers/net directory.
As part of the move, rename the "vmxnet3" subdirectory, containing the
original FreeBSD drivers, from "vmxnet3" to the more standard name
"base", to indicate it contains the base drivers used for the
implementation.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Move virtio PMD to drivers/net directory
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Move ring PMD to drivers directory
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Move pcap pmd to drivers/net directory
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Move null PMD to drivers/net directory
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
move mlx4 PMD to drivers/net directory
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
move ixgbe PMD to drivers/net directory.
As part of the move, we rename the ixgbe directory, containing the
ixgbe "base driver" code, from "ixgbe" to "base".
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Move i40e PMD to drivers/net directory.
As part of the move, rename the "i40e" directory, containing the "base
driver" code, from "i40e" to "base".
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
move fm10k PMD to drivers/net directory
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
move enic PMD to drivers/net directory
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
[Thomas: move vnic/ to base/]
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Move e1000 pmd to drivers/net directory
As part of move, rename "e1000" subdirectory, which contains the code
from the "base driver", to "base".
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Move bonded ethdev pmd to drivers/net
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
move af_packet pmd to drivers/net directory
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Add a new top-level "drivers" directory to which all PMDs will be moved
for easier maintenance of both lib folder and drivers themselves. This
new directory is a dependency of all the apps in the app folder, so
the makefiles for each app are updated.
To the new top-level directory add a "net" subdirectory to classify
more specifically our existing PMDs as ethernet drivers
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
[Thomas: fix dependencies and merge several patches]
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
