Add a new adminq function that allows driver to configure per-VLAN
broadcast promiscuous mode, similar to how we handle unicast and
multicast promiscuous modes.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
This patch adds I40E_NVMUPD_STATE_ERROR state for NVM update.
Without this patch driver has no possibility to return NVM image write
failure.This state is being set when ARQ rises error.
arq_last_status is also updated every time when ARQ event comes,
not only on error cases.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
We already define I40E_AQ_PHY_TYPE_EXT_25G* flags in the response adminq
structure above, and do not need to re-define these.
While we are here, replace 0X with 0x as normal style.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
The firmware expects the Port number to be in Little Endian format, and
the i40e_aq_add_udp_tunnel command clearly expects the udp_port variable
to be in Host order, as it uses CPU_TO_LE16(). It was recently
discovered in the Linux driver that we were passing a Big Endian port
number, which was therefor not enabling the UDP tunnel correctly.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acquire NVM lock before reads on all devices. Previously, locks were
only used for X722 and later. Fixes an issue where simultaneous X710
NVM accesses were interfering with each other.
Fixes: 8db9e2a1b2 ("i40e: base driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
By default the device clears all MAC filter information on PF Reset.
However, this will cause Wake-On-LAN to fail because the wake filters
are deleted on transition to D3 power state. To get around this,
firmware is adding functionality to preserve certain MAC filters during
PFR. These bits allow the driver tell the FW which filters to preserve.
Set the datalen field and add I40E_AQ_FLAG_BUF/I40E_AQ_FLAG_RD flags in the
desc struct for the WoL/Proxy AQ descriptors. The WoL/Proxy AQ commands
were failing because these were missing.
Fixes: 3c89193a36 ("i40e/base: support WOL config for X722")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
This patch implements a function to set a VSI to broadcast, multicast, and
unicast promiscuous mode all at once. This is specifically needed to set
the WoL/Proxy VSI created by FW to full promiscuous mode during power down
for WoL patterns and protocol offloads to function properly.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
This patch implements the clear Wake on LAN (WoL) filters admin queue
function which clears out ALL WoL patterns programmed into
the flex filters.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Define the values for the 25G PHY type bit-fields that match
reported values from firmware. There was a gap in the bit
fields but no corresponding gap i40e_aq_phy_type enum.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Add FEC bits to the PHY capabilities AQ command struct. This is required
for 25GbE support. Change the name of the generic mod_type_ext field to
indicate that it is now used for handling FEC.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Microsoft recently removed the requirement for VFs to use the VMBus.
The Fort Park Windows VF has been changed to use only the hardware
mailbox, so the Hyper-V VF device ID can be removed.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
I40E_MAC_X710 was supposed to be for 10G and I40E_MAC_XL710
was supposed to be for 40G. But i40e_set_mac_type() sets
I40E_MAC_XL710 for all device IDS. I40E_MAC_X710 is not
used at all. Thus deprecating this extra macro.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
The PHY type value for unrecognized PHYs and cables was changed
based on firmware version number. Newer hardware use lower firmware
version numbers and this was causing some PHYs to be identified
as type 0x16 instead of 0xe (unknown).
Without this patch, newer card will incorrectly identify unknown
PHYs and cables.
This change adds hardware type to the check for firmware version
so the PHY type is reported correctly.
Fixes: 8db9e2a1b2 ("i40e: base driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Currently i40e_bus_info has PCI device and function info only. However
in log messages slot number (i.e hw->bus.device) is being printed
as bus number. Another field should be added to provide bus number
info and preserve existing information.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Some external PHYs require Clause22 and Clause45 method for
accessing registers. Mostly used for X722 support.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
This patch fixes a problem where it could take a very
long time (>100 msec) to print the link down notification.
This problem is fixed by changing how often we update link
info from fw, when link is down. Without this patch, it can
take over 100msec to notify user link is down.
Fixes: e6691b428e ("i40e/base: fix PHY NVM interaction")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Group together the minimum set of offload capabilities that are always
supported by VF in base mode. This define would be used by PF to make
sure VF in base mode gets minimum of base capabilities.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Incorrect bit mask was used for testing "get link status" response.
Instead of I40E_AQ_LSE_ENABLE (which is actually 0x03) it should
be I40E_AQ_LSE_IS_ENABLED (which is defined as 0x01).
Fixes: 8db9e2a1b2 ("i40e: base driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
This patch changes some assignments and removing the unnecessary
code to avoid error reported by static analysis tools.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Add phy_type_ext copied from old setting to rpevents 25G PHY
types from being disabled when setting the flow control modes.
Fixes: 51131ae119 ("net/i40e/base: get PHY abilities for 25G")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Add ENCAP_CSUM offload negotiation flag. Currently VF assumes checksum
offload for encapsulated packets is supported by default. Going forward,
this feature needs to be negotiated with PF before advertising to the
stack. Hence, we need a flag to control it.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Examples of recoverable exceptions because of Tx error are:
- Tx descriptor PCI read error
- invalid Tx option descriptor
- Tx option descriptor not supported by the firmware variant
- unexpected Tx option descriptor (e.g. missing FATSO2A before
FATSO2B, missing FATSO2B after FATSO2A)
- incomplete packet push (CONT bit set in the latest pushed DMA
descriptor)
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Examples of recoverable exceptions are:
- unexpected Rx event (Rx scatter abort with non-zero size,
too big Rx descriptors batch completed)
- Rx error due to invalid Rx descriptors push
- Rx error due to Rx descriptor read error (e.g. unmapped Rx ring
and denied by IOMMU)
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
Since Rx scatter is not supported, all scattered packets are discarded.
It is not always possible to disable scatter on Huntington, so we
should handle scattered packets correctly in any case.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
These functions should set the queue state in dev->data->rx_queue_state
array.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Check that Rx mbuf pool, MTU and Rx scatter config are in sync.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Take Rx buffer start alignment and end-padding into account.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Timers cannot be used to implement periodic polling, since it implies
requirement on application to process timers in the main loop.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The event queue is required for device level events (e.g. link status
change) and flush events.
Provide thread-safe function to poll the event queue since it may be
really done from different contexts.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Right now the code just logs the exception and sets flag to notify
subsequent event handlers and poller that recovery is required.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
