Add SPQ timeout base driver parameter support management FW timeout values
other than default and none. Have fallback mechanism for old MFWs.
Reduce the default timeout to 1 sec.
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
Upgrade QEDE PMD FW to version 8.30.12.0.
The firmware upgrade change details are as:
- Add support for steering by IP and UDP destination port.
- Add source QP field for GSI offload.
- Add UFP support.
- Add support for outer IPv4 TX CSO with unknown tunnel type (in addition
to inner header CSO).
- Support flow ID in accelerated RFS flow.
- Allow Doorbell on empty SPQ and LL2 TX queue (for doorbell recovery).
- Enable PCI Relaxed Ordering for L2 RX data placement.
- Additional enhancements and bug fixes
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
This is an attempt to clean up many unused API parameters across the base
code. Most of the changes are related to removing unused p_hwfn or p_ptt
handlers. The warnings are generated using 'unused-parameter' cflags.
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
Add support for doorbell overflow recovery mechanism:
The doorbell recovery mechanism consists of a list of entries which
represent doorbelling entities (l2 queues, roce sq/rq/cqs, the slowpath
spq, etc). Each entity needs to register with the mechanism and provide
the parameters describing it's doorbell, including a location where last
used doorbell data can be found. The doorbell execute function will
traverse the list and doorbell all of the registered entries.
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
Revise the manamgement FW mbox access locking scheme for the access to the
MFW mailbox:
- add a new linked list called cmd_list to ecore_mcp_info that tracks all
the mailbox commands sent to management FW and ones waiting for
response.
- add a mutex lock called cmd_lock to ecore_mcp_info, a spinlock used to
serialize the access to this cmd_list and makes sure that the mbox is
not a pending one before sending a new mbox request. It protects the
access to the mailbox commands list and sending of the commands.
- add ecore_mcp_cmd_add|del|get_elem() APIs for new access scheme
- remove ecore_mcp_mb_lock() and ecore_mcp_mb_unlock()
- add a mutex lock called link_lock to ecore_mcp_info, a spinlock used for
syncing SW link-changes and link-changes originating from attention
context. This locking scheme prevents possible race conditions that may
occur, such as during link status reporting.
- Surround OSAL_{MUTEX,SPIN_LOCK}_{ALLOC,DEALLOC} with
'#ifdef CONFIG_ECORE_LOCK_ALLOC'. In case memory has to be allocated for
lock primitives, then compile driver with CONFIG_ECORE_LOCK_ALLOC flag.
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
Use the ptt[PF translation table] handler that is passed rather than using
main ptt from the HW function.
In ecore_hw_get_resc()'s error flow, release the MFW generic resource lock
only if needed.
Change the verbosity level of GRC timeout from DP_INFO() to DP_NOTICE().
Reduce verbosity of print in ecore_hw_bar_size().
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
Merge hw_stop and hw_reset into one function.
Prevent race condition between MFW attentions and pf stop command during
unload flow that causes an ASSERT.
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
This change is in preparation to work with new FW 8.18.9.0.
Rename the defines to use E4_ and structs to use e4_. This renaming
is to add support for future chipsets.
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
Replace the raw I/O device memory read/write access with eal
abstraction for I/O device memory read/write access to fix
portability issues across different architectures.
CC: Harish Patil <harish.patil@cavium.com>
CC: Rasesh Mody <rasesh.mody@cavium.com>
Signed-off-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Add support for 8.14.x.x firmware.
The new firmware adds support for external PHY BCM8485x; configures
fixed link speed with transceiver/cable not supporting negotiation;
supports engine swap; supports overriding PCIe preset equalization
value; checks pause too long for ports and reads die temperature
every second for shutdown threshold.
It includes change in FLR flow when there is a SW initiated FLR.
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
Add new option called external PBL (page base list) to ecore_chain_alloc
for future use. Mark chain as external if external PBL is provided.
Signed-off-by: Rasesh Mody <rasesh.mody@cavium.com>
This patch updates the base driver and incorporates necessary changes
required to bring in the new firmware 8.10.9.0.
In addition, it would allow driver to add new functionalities that might
be needed in future.
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Change details:
- adds new comments
- modifies some of the existing comments
- abstract code into macros
- split long lines
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
The base driver is the backend module for the QLogic FastLinQ QL4xxxx
25G/40G CNA family of adapters as well as their virtual functions (VF)
in SR-IOV context.
The purpose of the base module is to:
- provide all the common code that will be shared between the various
drivers that would be used with said line of products. Flows such as
chip initialization and de-initialization fall under this category.
- abstract the protocol-specific HW & FW components, allowing the
protocol drivers to have clean APIs, which are detached in its
slowpath configuration from the actual Hardware Software Interface(HSI).
This patch adds a base module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
