Some drivers might allow to commit the traffic management hierarchy
while being in running state. Therefore, removes port status check
before invoking hierarchy commit API in the cli. If needed, device can
add port status check at the driver layer.
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
failsafe device has vlan stripping configured at startup however once
a sub device is found as non-capable of vlan-stripping failsafe
updates it configuration and removes vlan stripping from it.
This update occurs only once at startup. Following a later plugin
attempt and in case of vlan stripping mismatch between failsafe
configuration and device capability - failsafe cannot recover and the
device remains constantly in plug out state.
The sequence of events leading to this situation is described as
follows:
1. Start testpmd with failsafe where mlx4 is a sub device (not capable
of vlan stripping). Expected printout:
PMD: net_failsafe: Disabling VLAN stripping offload
2. Execute:
testpmd> port stop all
testpmd> port config all max-pkt-len 2048
testpmd> port start all
3. Do a plug out (e.g. disable sriov)
4. Do a plug in (e.g. enable sriov)
5. Expected result: failsafe successfully configures and starts its sub
devices
Actual result: failsafe is continuously failing with these messages:
PMD: net_failsafe: VLAN stripping offload requested but not supported by
sub_device 0
PMD: net_failsafe: device already configured, cannot fix live
configuration
PMD: net_failsafe: Unable to synchronize sub device state
Root cause analysis: at startup failsafe removes vlan stripping from its
configuration. After executing "port config all max-pkt-len 2048"
testpmd marks failsafe in need for configuration update.
After executing "port start all" testpmd overrides failsafe
configuration with its own configuration which includes vlan stripping
During the plugin attempt failsafe refuses to update its configuration
by removing vlan stripping since it has already updated its
configuration at startup.
The fix is for failsafe to stop validation and disabling non-supported
offloads in its sub-devices.
Fixes: bbc6a53dda ("net/failsafe: support Rx offload capabilities")
Cc: stable@dpdk.org
Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Memory regions assigned to hardware and used during Tx/Rx are mapped to
mbuf pools. Each Rx queue creates its own MR based on the mempool
provided during queue setup, while each Tx queue looks up and registers
MRs for all existing mbuf pools instead.
Since most applications use few large mbuf pools (usually only a single
one per NUMA node) common to all Tx/Rx queues, the above approach wastes
hardware resources due to redundant MRs. This negatively affects
performance, particularly with large numbers of queues.
This patch therefore makes the entire MR registration common to all
queues using a reference count. A spinlock is added to protect against
asynchronous registration that may occur from the Tx side where new
mempools are discovered based on mbuf data.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
This is done for consistency with the rest of the code.
Fixes: 078b8b452e ("net/mlx4: add RSS flow rule action support")
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Replace most of the memory barriers by IO memory barriers since they
are all targeted to the DRAM; This improves code efficiency for
systems which force store order between different addresses.
Only the doorbell register store should be protected by memory barrier
since it is targeted to the PCI memory domain.
Limit pre byte count store IO memory barrier for systems with cache
line size smaller than 64B (TXBB size).
This patch improves Tx performance by 0.2MPPS for one segment 64B
packets via 1 queue with 1 core test.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Optimize single segment case by processing it in different block which
prevents checks, calculations and barriers relevant only for multi
segment case.
Call a dedicated function for handling multi segments case.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Remove usage of variable which count the packets for completion and
doesn't add more information than packets counter.
Remove no space in elements ring check which is already covered by
regular Tx flow.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Associate memory region to mempool (on data path) in a short function.
Handle the less common case of adding a new memory region to mempool
in a separate function.
Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
When a VF port is bound to VFIO-PCI, miscellaneous interrupt is
mapped to MSI-X vector 0 and Rx queues interrupt are mapped to
other vectors in vfio_enable_msix( ). To simplify implementation,
all VFIO-PCI bound i40e VF Rx queue interrupts can be mapped in
vector 1. And as current igb_uio only support only one vector,
i40e VF PMD should use vector 0 for igb_uio and vector 1 for
VFIO-PCI. Without this patch, VF Rx queue interrupt is mapped
to vector 0 in register settings and mapped to VFIO vector 1
in vfio_enable_msix( ), and then all Rx queue interrupts will
be missed.
Also remove 2 unused macro definitions.
Fixes: 4b90a3ff26 ("i40evf: support Rx interrupt")
Fixes: 975ffea6f6 ("net/i40e: remove DPDK PF version specific code")
Cc: stable@dpdk.org
Signed-off-by: Wei Dai <wei.dai@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
When a VF port is bound to VFIO-PIC, only miscellaneous interrupt
is mapped to VFIO vector 0 in i40evf_dev_init( ).
In i40evf_dev_interrupt_handle( ) and i40evf_dev_rx_queue_intr_enable( ),
if previous VFIO interrupt mapping set in i40evf_dev_init( ) is not
cleared, it will fail when PMD tries to map Rx queue interrupt to other
VFIO vectors by calling rte_intr_enable( ).
This patch clears the VFIO interrupt mappings before setting both
miscellaneous and Rx queue interrupt mappings again to avoid failure.
And remove the calling of rte_intr_enable( ) in
i40evf_dev_interrupt_handler( ) as there is no need to map VFIO interrupt
in this function repeatedly.
Fixes: 4b90a3ff26 ("i40evf: support Rx interrupt")
Cc: stable@dpdk.org
Signed-off-by: Wei Dai <wei.dai@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
The action for L2 tunnel should be VF or PF, not QUEUE.
Fixes: 99e7003831 ("net/ixgbe: parse L2 tunnel filter")
Cc: stable@dpdk.org
Signed-off-by: Wei Zhao <wei.zhao1@intel.com>
Tested-by: Yuan Peng <yuan.peng@intel.com>
Acked-by: Wei Dai <wei.dai@intel.com>
At the end of the queue release, we can free the containers for the
queue objects.
Fixes: dfaff37fc4 ("vmxnet3: import new vmxnet3 poll mode driver implementation")
Cc: stable@dpdk.org
Signed-off-by: Chas Williams <chas3@att.com>
Reviewed-by: Luca Boccassi <bluca@debian.org>
VLAN id is limited to MLX5_MAX_VLAN_IDS which is not verified by the code
before trying to add a new VLAN filter.
Fixes: 272733b5eb ("net/mlx5: use flow to enable unicast traffic")
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
In case errno contains some non-zero value and call to strtoul() is
successful -2 error will be returned.
Setting errno to zero before calling strtoul() makes sure
errors will be handled correctly.
Fixes: 0ddc9b815b ("net/mrvl: add net PMD skeleton")
Signed-off-by: Tomasz Duszynski <tdu@semihalf.com>
A check was previously added to drop Tx packets greater than what the Nic
is capable of sending since such packets can freeze the send queue. The
check did not account for TSO packets however, so TSO was limited to 9208
bytes.
Check packet length only for non-TSO packets. Also insure that TSO packet
segment size plus the headers do not exceed what the Nic is capable of
since this also can freeze the send queue.
Use the PKT_TX_TCP_SEG ol_flag instead of m->tso_segsz which is the
preferred way to check for TSO.
Fixes: ed6e564c21 ("net/enic: fix memory leak with oversized Tx packets")
Cc: stable@dpdk.org
Signed-off-by: John Daley <johndale@cisco.com>
The description of i40e 16 byte descriptor is not clear
enough. Add more details.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Initialise struct mlx5_fdir to avoid passing non initialised
items/actions arrays elements to the generic flow interpreter.
Fixes: 4c3e9bcdd5 ("net/mlx5: support flow director")
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Yongseok Koh <yskoh@mellanox.com>
Fix a strange behavior from the NIC, when the flow starts with a VXLAN
layer with a VNI equals to zero all the traffic will match within this
rule.
Fixes: 2e709b6aa0 ("net/mlx5: support VXLAN flow item")
Cc: stable@dpdk.org
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Yongseok Koh <yskoh@mellanox.com>
In validate() it sets the value to 1 whereas the expected one is
IBV_FLOW_SPEC_INNER.
Fixes: c2c6ddd51d ("net/mlx5: limit flow API rules to one tunnel")
Cc: stable@dpdk.org
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Yongseok Koh <yskoh@mellanox.com>
if dpaa2_dev_tx_queue_setup is called multiple times, the
assignment of device->data->tx_queues is not done, as a result
tx_queues remain NULL after reconfiguration.
This patch sets the tx_queues from the device private data to the
usable device tx queues.
Fixes: 7ae777d064 ("net/dpaa2: add support for congestion notification")
Cc: stable@dpdk.org
Signed-off-by: Akhil Goyal <akhil.goyal@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
The counter set should be destroyed only after the flow was destroyed.
Fixes: 9a761de8ea ("net/mlx5: flow counter support")
Signed-off-by: Ori Kam <orika@mellanox.com>
Acked-by: Yongseok Koh <yskoh@mellanox.com>
This patch change default aggregator mode to stable
when using rte_eth_bond_create()
Fixes: 6d72657ce3 ("net/bonding: add other aggregator modes")
Cc: stable@dpdk.org
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Acked-by: Michal Jastrzebski <michalx.k.jastrzebski@intel.com>
And small performance improvement
Fixes: 9a0752f498 ("net/ixgbe: enable inline IPsec")
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Fix i40e stop receiving on ARM, as the statuses of RX descriptors
are not consistent, which is caused by cacheable hugepages.
Fixes: ae0eb310f2 ("net/i40e: implement vector PMD for ARM")
Cc: stable@dpdk.org
Signed-off-by: Jianbo Liu <jianbo.liu@arm.com>
We are not programming the vlan_spoof setting currently owing to
an unnecessary check. This patch fixes that.
Fixes: 36735a932c ("net/bnxt: support set VF QOS and MAC anti spoof")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Users are not prevented from creating flow rules targeting nonexistent
queues, which silently makes such rules drop-like.
While it can be thought as a feature, reporting an error instead is
actually far more useful in order to catch common mistakes.
Fixes: 078b8b452e ("net/mlx4: add RSS flow rule action support")
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
When not in isolated mode, internal flow rules are automatically
maintained by the PMD to receive traffic according to global device
settings (MAC, VLAN, promiscuous mode and so on).
Since RSS support was added to the mix, it must also check whether Rx
queue configuration has changed when refreshing flow rules to prevent
the following from happening:
- With a smaller number of Rx queues, traffic is implicitly dropped
since the existing RSS context cannot be re-applied.
- With a larger number of Rx queues, traffic remains balanced within the
original (smaller) set of queues.
One workaround before this commit was to temporarily enter/leave
isolated mode to make it regenerate internal flow rules.
Fixes: 7d8675956f ("net/mlx4: add RSS support outside flow API")
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Value of I40E_GL_SWR_PRI_JOIN_MAP_0 need to be corrected or mirror
does not work on latest firmware 6.0.
Fixes: 77370db964 ("net/i40e: fix ethertype filter for new FW")
Cc: stable@dpdk.org
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
PF multiport support has some limitations like not allowing plugging or
unplugging of single ports as they all belong to same PCI device.
A previous patch for removing detachable flag introduced a wrong check.
Fixes: 00a3d8104a ("ethdev: remove detachable device flag")
Signed-off-by: Alejandro Lucero <alejandro.lucero@netronome.com>
When adding count action to a drop flow rule while the device was not
started, the counter was not saved in the flow.
Fixes: 9a761de8ea ("net/mlx5: flow counter support")
Signed-off-by: Ori Kam <orika@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Flow director API does not provide a layer 2 configuration when the
filter is for layer 3 and 4 causing the translation to generic flow API
to be wrong, as not providing a mask for layer ends by using the
default one.
In this case, the Ethernet mask layer is full whereas it must be empty.
Fixes: 4c3e9bcdd5 ("net/mlx5: support flow director")
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Yongseok Koh <yskoh@mellanox.com>
In some cases when a VF driver is unloaded after the PF driver,
certain HWRM commands are returned with an error.
Instead the PF can tell the FW to permit these commands in order
to allow a clean unload.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Set the filter_type before we match a new filter against existing
filters. Otherwise we are missing the existing filters.
Fixes: 2d64da097a ("net/bnxt: support FDIR")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are wrongly "OR-ing" the vnic->hash_type instead of assigning
the new hash type thereby wrongly configuring hash settings.
Fixing it.
Fixes: fcc0aa1edc ("net/bnxt: add RSS hash configuration")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The flow engine in mlx5 searches for the most specific layer in the
pattern in order to set the flow rule priority properly.
Since the RSS can be currently performed only for the outer headers, avoid
updating the layer for the inner headers.
Fixes: 8086cf08b2 ("net/mlx5: handle RSS hash configuration in RSS flow")
Signed-off-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
On SUSE11 with gcc 4.5.1 the following build error occurred,
most likely because of improper handling of annonymous unions:
drivers/net/ixgbe/ixgbe_ipsec.c:579:4: error:
unknown field ‘ipsec’ specified in initializer
Fixes: 9a0752f498 ("net/ixgbe: enable inline IPsec")
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
If multiple queue pairs are created but all are not used, the
device is never started, as unused queues aren't enabled and
their ring addresses aren't translated. The device is changed
to running state when all rings addresses are translated.
This patch fixes this by postponning rings addresses translation
at kick time unconditionnaly, VHOST_USER_F_PROTOCOL_FEATURES
being negotiated or not.
Reported-by: Lei Yao <lei.a.yao@intel.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
Acked-by: Yuanhan Liu <yliu@fridaylinux.org>
Unsuccesfull memory allocation for elements inside cfgfile
structure could result in resource leak.
Fixed by pointer verification after each malloc,
if malloc fail - error branch is proceeded with freeing memory.
Coverity issue: 195032
Fixes: d4cb819758 ("cfgfile: support runtime modification")
Signed-off-by: Jacek Piasecki <jacekx.piasecki@intel.com>
Acked-by: Michal Jastrzebski <michalx.k.jastrzebski@intel.com>
