Some statistics were deprecated since release 2.1 (49f386542a).
The last deprecated counter to be used was imcasts.
The VF loopback statistics are also removed as they are used only
in igb and duplicated in extended statistics.
The new counters should be added to extended statistics.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Remy Horton <remy.horton@intel.com>
VxLAN & NVGRE are supported by x550. As we know HW can parse
the packet and tell SW the type info. For VxLAN & NVGRE packets
there's some change. HW will not tell SW the info of the outer
header but the inner header instead. But we always take the
info as it's for the outer header. So the packet type info is
not right when x550 receives VxLAN & NVGRE packets.
As x550 only supports IPv4 VxLAN & NVGRE packets, we can tell
the outer header of VxLAN is IPv4 + UDP, and the outer header
of NVGRE is IPv4 only. What we don't know is if there's
optional field in the outer IPv4 header.
This patch implement the support of packet type for VxLAN &
NVGRE. And it fixes the wrong packet type issue either.
BTW:
It doesn't fix any existing commit as although it resolve an
issue it's more like a new feature but not a fix.
Reported-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch redesigns the API to set the link speed/s configuration
of an ethernet port. Specifically:
- it allows to define a set of advertised speeds for
auto-negociation.
- it allows to disable link auto-negociation (single fixed speed).
- default: auto-negociate all supported speeds.
A flag autoneg in struct rte_eth_link indicates if link speed was a
result of auto-negociation or was fixed by configuration.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Tested-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Tested-by: Beilei Xing <beilei.xing@intel.com>
Tested-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The speed capabilities of a device can be retrieved with
rte_eth_dev_info_get().
The new field speed_capa is initialized in the drivers without
taking care of device characteristics in this patch.
When the capabilities of a driver are accurate, the table in
overview.rst must be filled.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
The speed numbers ETH_LINK_SPEED_ are renamed ETH_SPEED_NUM_.
The prefix ETH_LINK_SPEED_ is kept for AUTONEG and will be used
for bit flags in next patch.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Some duplex values are replaced from 0 to half-duplex when link is down.
Some drivers are still using their own constants for duplex modes.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Define and use ETH_LINK_UP and ETH_LINK_DOWN where appropriate.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Silence a compiler warning that this variable may be used uninitialized.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tell the compiler to use an unsigned constant for the config shifts.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Panu Matilainen <pmatilai@redhat.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The lower 16 bits of EICR register are used for queue interrupts,
dpdk framework take over the first bit for other interrupts like
LSC, so there're only 15 bits left for queue interrupts mapping.
This patch adds a check for the num of interrupt queues at
dev_start.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
When starting testpmd with multiple queues on a ixgbe VF
port, it failed with this printing, "nb_rxq(4) is greater
than max_rx_queues(1)".
The root cause is the VF doesn't get the right max rx queue
number from PF and it uses the default value 1.
VF max rx queue number is set by PF through mailbox messages.
The message for this setting only supports version 1.1. As
message version is updated to 1.2, VF cannot parse the rx queue
number setting message correctly.
This patch raise a specific base code update for this issue.
Fixes: 72dec9e37a ("ixgbe: support multicast promiscuous mode on VF")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
l2 tunnel and e-tag are not supported on the new x550em_a NICs, due
to missing checks for that mac type in the code.
This patch adds in the necessary conditional checks to enable the features
for x550em_a.
Fixes: 22e77d4501 ("ixgbe: support L2 tunnel operations")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
An issue is found on x550em NICs: ieee1588 is not working, the time is
always reported as 0.
The root cause is that the timer is only supported by the driver for x550,
switch statement entries are missing for x550em_x and x550em_a. This patch
adds those missing entries.
Fixes: a7740dc130 ("ixgbe: support new devices and MAC types")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
icc (icc (ICC) 16.0.1 20151021) is generating following compile error:
CC ixgbe_rxtx.o
.../drivers/net/ixgbe/ixgbe_rxtx.c(153): error #3656: variable
"free" may be used before its value is set
(nb_free > 0 && m->pool != free[0]->pool)) {
^
Indeed this is a false positive and code is correct.
"nb_free" check prevents the free[] access before its value set.
Disabling this icc warning (#3656) for file ixgbe_rxtx.c.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Ixgbe HW supports 128 TX queues. However, the full 128 queues are only
available in VT and DCB mode. In normal default "none" mode (VT/DCB off)
the maximum number of available queues is only 64.
The driver doesn't check the mode when reporting the available
number of queues, allowing more that 64 queues to be used in all cases.
If a queue no. >=64 is used in default mode, the TX packets will be dropped
silently.
This change adds a check to forbid using a queue number larger than 64
during device configuration (in default mode), so that the problem is
reported as early as possible.
Fixes: 27b609cbd1 ("ethdev: move the multi-queue mode check to specific drivers")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Internal variable containing the number of TX queues for a device,
was being incorrectly assigned the number of RX queues, instead of TX.
Fixes: 27b609cbd1 ("ethdev: move the multi-queue mode check to specific drivers")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
There's an issue reported. In the scenario DPDK PF + DPDK VF,
if the VF port is closed, PF port cannot receive packets.
I found at that time the promicuous mode is disabled on the PF
port. But it should be enabled.
When VF port is closed, it will send a message to its PF port to
reset it. During this, PF port will also reset its own
promicuous mode. Which promiscuous mode should be set depends on
the parameter stored in the device data. In the function
set_rx_mode, the pointer of device data points to the wrong
address. So, the promiscuous mode is wrong.
Fixes: 00e30184da ("ixgbe: add PF support")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Reported-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Current vector RX can't always set the packet_type properly.
To be more specific:
a) it never sets RTE_PTYPE_L2_ETHER
b) it doesn't handle tunnel ipv4/ipv6 case correctly.
c) it doesn't check is IXGBE_RXDADV_PKTTYPE_ETQF set or not.
While a) is pretty easy to fix, b) and c) are not that straightforward
in terms of SIMD ops (specially b).
So far I wasn't able to make vRX support packet_type properly without
noticeable performance loss.
So for now, just remove that functionality from vector RX and
update dev_supported_ptypes_get().
Fixes: 3962541758 ("mbuf: redefine packet type")
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Cunming Liang <cunming.liang@intel.com>
For x550 device, the reta table has 512 entries, but in function
ixgbe_dev_rss_reta_query and ixgbe_dev_rss_reta_update we use an
"uint8_t i" to traverse the entries, this will lead the function
to an endless loop.
This patch changes the data type from uint8_t to uint16_t to fix
the issue.
Fixes: 4bee94a6c2 ("ixgbe: support 512 RSS entries on x550")
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add a new API rte_eth_dev_get_supported_ptypes to query what packet types
can be filled by a given device. The device should be already started or
its PMD RX burst function already decided, since the packet types supported
may vary depending on RX function.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Comment for "ierrors" counter says that it counts erroneous received
packets. But for some reason "imissed" counter is added to "ierrors"
counter in most drivers.
It is a mistake, because missed packets are obviously not received.
This patch fixes it.
Fixes: 70bdb18657 ("ethdev: add Rx error counters for missed, badcrc and badlen packets")
Fixes: 6bfe648406 ("i40e: add Rx error statistics")
Fixes: 856505d303 ("cxgbe: add port statistics")
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The multi queue mode ETH_MQ_RX_VMDQ_DCB_RSS is not supported in
ixgbe driver.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Call the ixgbevf_remove_mac_addr() function in the ixgbevf_dev_close()
function to ensure that the VF traffic goes to the PF after stop,
close and detach of the VF.
Fixes: af75078fec ("first public release")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add the nb_rx_q and nb_tx_q values to the error message
to give details about the error.
Fixes: 27b609cbd1 ("ethdev: move the multi-queue mode check to specific drivers")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Releasing the rx and tx queues is already done in ixgbe_dev_close()
so it does not need to be done in eth_ixgbevf_dev_uninit().
Fixes: 2866c5f1b8 ("ixgbe: support port hotplug")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
For the secondary process of DPDK to initialize ixgbevf, it will always
use the simple RX function or LRO RX function, and this behavior is not
the same RX/TX function selection logic as it is for the primary process.
Use the ixgbe_set_tx_function and ixgbe_set_rx_function to select the
RX/TX function when secondary process calls the init function for eth dev.
Fixes: 9d8a92628f ("ixgbe: remove simple scalar scattered Rx method")
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Normally the auto-negotiation is supported by FW. SW need not care about
that. But on x550em_x, FW doesn't support auto-neg. As the x550em_x ports
are 10G, if we connect the port will a peer which is 1G, the link will
always be down.
We need support auto-neg by SW to avoid this link down issue. As we already
have the code to handle the link speed setting, what we need is a trigger.
When the advertised link speed changes, a PHY interruption will be
triggered. So, we should handle this interrupt and call ixgbe_handle_lasi
to set the link speed correctly.
Please be aware it's working when auto-neg is on. If the auto-neg of the
peer port is turned off and its speed is indicated manually, we should also
set the speed of our own port manually.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Add multicast promiscuous mode support on ixgbe VF driver.
Please note if we want to use this promiscuous mode, we need both PF
and VF driver to support it. The reason is this VF feature is
configged on PF.
If use kernel PF driver + dpdk VF driver, make sure kernel PF driver
support VF multicast promiscuous mode. If use dpdk PF + dpdk VF,
better make sure PF driver is the same version as VF.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
It's more valuable to abstract the link read/write interface. As such,
change the following method names, and add them to a new link info
structure:
read_i2c_combined => read_link
read_i2c_combined_unlocked => read_link_unlocked
write_i2c_combined => write_link
write_i2c_combined_unlocked => write_link_unlocked
This will allow X550EM_a to override these methods for MDIO access
while X550EM_x provides methods to use I2C combined access.
Initially the structure is just method pointers and a bus
address.
Two functions involved in combined I2C accesses were moved from
ixgbe_phy.c to ixgbe_x550.c. The underlying functions that carry
out the combined I2C accesses were left in ixgbe_phy.c because
they share some functions with other I2C methods.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The MDIO clock speed must be reconfigured after the MAC reset.
The MDIO clock speed becomes invalid, therefore the driver reads
invalid PHY register values. The driver now set the MDIO clock
speed prior to initializing PHY ops and again after the MAC reset.
As now the MDIO speed gets set in more than one place, make a
function for it so it will always be done correctly.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Do not set FDIRCTRL.DROP_NO_MATCH in ixgbe_init_fdir_perfect_82599(),
this bit is already set in ixgbe_set_fdir_drop_queue_82599() which
makes more sense for drivers that call that function.
This resolves an issue where packets were being dropped when switching
to perfect filters mode.
Setting this bit makes no sense in perfect filters mode for the
driver as we do not want to route all packets that don't match an FDIR
rule to a single queue and instead fall back to RSS.
Drivers that need this bit set can call ixgbe_set_fdir_drop_queue_82599()
and the ones that don't, can preserve the old behavior.
Fixes: 2241ce2816 ("ixgbe/base: add flow director drop queue")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The X550EM_a device provides the MAC_SGMII_BUSY register to
indicate when slow SGMII register writes complete. Add
definitions for the register. No definitions are provided for
the individual bits under the theory that it is better to wait
for everything to complete when needed rather than try to map
out which reads need to wait for which writes. So we should wait
when anything is marked as "busy".
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Instead of not defining the callback for set_phy_power when
manageability is enabled, put the check in the set_phy_power
function so that only turning the power off is conditional on
management, but not turning the PHY on.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch resolves an issue where VF mac address is zeroed out
in cases where the VF driver is loaded while the PF interface
is down.
The solution is to only set it when we get an ACK from the PF.
Fixes: 6202266e56 ("ixgbe/base: vf changes")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Only x550em_x V1 was supported before. Now V2 is supported.
A mask for V1 and V2 is defined and used to support both.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add new X550EM_a devices and their mac types, X550EM_a
and X550EM_a_vf.
Update the code to use the new devices and mac types.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Currently, ixgbe vf and pf will disable interrupt twice in
stop stage and uninit stage. It will cause an error:
testpmd> quit
Shutting down port 0...
Stopping ports...
Done
Closing ports...
EAL: Error disabling MSI-X interrupts for fd 26
Done
because the interrupt has already been disabled in stop stage.
Since it is enabled in init stage, better remove from
stop stage.
Fixes: 0eb609239e ("ixgbe: enable Rx queue interrupts for PF and VF")
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The freeing of mbuf's in ixgbe is one of the observable hot spots
under load. Optimize it by doing bulk free of mbufs using code similar
to i40e and fm10k.
Drop the no longer needed micro-optimization for the no refcount flag.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The patch add VxLAN & NVGRE TX checksum off-load. When the flag of
outer IP header checksum offload is set, we'll set the context
descriptor to enable this checksum off-load.
Also update release notes for VxLAN & NVGRE checksum off-load support.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
X550 will do VxLAN & NVGRE RX checksum off-load automatically.
This patch exposes the result of the checksum off-load.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add UDP tunnel port add/del support on ixgbe. Now only
support VxLAN port configuration.
Although according to the specification the VxLAN port has
a default value 4789, it can be changed. We support VxLAN
port configuration to meet the change.
Note, the default value of VxLAN port in ixgbe NICs is 0. So
please set it when using VxLAN off-load.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add support of l2 tunnel configuration and operations.
1, Support modifying ether type of a type of l2 tunnel.
2, Support enabling and disabling the support of a type of l2 tunnel.
3, Support enabling/disabling l2 tunnel tag insertion/stripping.
4, Support enabling/disabling l2 tunnel packets forwarding.
5, Support adding/deleting forwarding rules for l2 tunnel packets.
Only support E-tag now.
Also update the release note.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
On X550, as required by datasheet, E-tag packets are not expected
when double VLAN are used. So modify the register PFVTCTL after
enabling double VLAN to select pool by MAC but not MAC or E-tag.
An introduction of E-tag:
It's defined in IEEE802.1br. Please reference this website,
http://www.ieee802.org/1/pages/802.1br.html.
A brief description.
E-tag means external tag, and it's a kind of l2 tunnel. It means a
tag will be inserted in the l2 header. Like below,
|31 24|23 16|15 8|7 0|
0| Destination MAC address |
4| Dest MAC address(cont.) | Src MAC address |
8| Source MAC address(cont.) |
12| E-tag Etherenet type (0x893f) | E-tag header |
16| E-tag header(cont.) |
20| VLAN Ethertype(optional) | VLAN header(optional) |
24| Original type | ...... |
...| ...... |
The E-tag format is like below,
|0 15|16 18|19 |20 31|
| Ethertype - 0x893f | E-PCP |DEI| Ingress E-CID_base |
|32 33|34 35|36 47|48 55 |56 63|
| RSV | GRP |E-CID_base|Ingress_E-CID_ext| E-CID_ext |
The Ingess_E-CID_ext and E-CID_ext are always zero for endpoints
and are effectively reserved.
The more details of E-tag is in IEEE 802.1BR. 802.1BR is used to
replace 802.1Qbh. 802.1BR is a standard for Bridge Port Extension.
It specifies the operation of Bridge Port Extenders, including
management, protocols, and algorithms. Bridge Port Extenders
operate in support of the MAC Service by Extended Bridges.
The E-tag is added to l2 header to identify the VM channel and
the virtual port.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Shaopeng He <shaopeng.he@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yong Liu <yong.liu@intel.com>
In order to set ether type of VLAN for single VLAN, inner
and outer VLAN, the VLAN type as an input parameter is added
to 'rte_eth_dev_set_vlan_ether_type()'.
In addition, corresponding changes in e1000, ixgbe and i40e
are also added.
It is an ABI break but ethdev library is already bumped for 16.04.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Fixed issue of byte order in ethdev library that the structure
for setting fdir's mask and flow entry is inconsist and made
inputs of mask be in big endian.
Fixes: 2d4c1a9ea2 ("ethdev: add new flow director masks")
Fixes: 76c6f89e80 ("ixgbe: support new flow director masks")
Reported-by: Yaacov Hazan <yaacovh@mellanox.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
