Since rte_flow is the only API for filtering operations,
the legacy driver interface filter_ctrl was too much complicated
for the simple task of getting the struct rte_flow_ops.
The filter type RTE_ETH_FILTER_GENERIC and
the filter operarion RTE_ETH_FILTER_GET are removed.
The new driver callback flow_ops_get replaces filter_ctrl.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Reviewed-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
When link goes down, disable the port's Rx path to drop the incoming
traffic closer to the wire, instead of accepting them in for further
Rx processing, only to eventually drop them at the port's RxQs. This
prevents unnecessary congestion in the Rx path. The port's Rx path
will be re-enabled once the link up event is received in the firmware
event queue.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Improve portability by replacing non-standard 'uint' with 'unsigned int'.
This solves the build error with musl libc:
In file included from ../drivers/net/cxgbe/cxgbe.h:9,
from ../drivers/net/cxgbe/cxgbe_ethdev.c:37:
../drivers/net/cxgbe/base/common.h:201:4: error: unknown type name 'uint'
201 | uint synmapen:1; /* SYN Map Enable */
| ^~~~
Fixes: bfcb257d30 ("net/cxgbe: enable RSS for VF")
Cc: stable@dpdk.org
Signed-off-by: Natanael Copa <ncopa@alpinelinux.org>
Reviewed-by: Morten Brørup <mb@smartsharesystems.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: David Marchand <david.marchand@redhat.com>
The rte_ethdev_driver.h, rte_ethdev_vdev.h and rte_ethdev_pci.h files are
for drivers only and should be a private to DPDK and not installed.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Steven Webster <steven.webster@windriver.com>
The jumbo frame uses the 'RTE_ETHER_MAX_LEN' as boundary condition.
If the Ether overhead is larger than 18 when it supports VLAN tag,
that will cause the jumbo flag rx offload is wrong when MTU size is
'RTE_ETHER_MTU'.
This fix will normalize the boundary condition with 'RTE_ETHER_MTU'
and overhead even though current overhead is 18.
Fixes: 4b2eff452d ("cxgbe: enable jumbo frames")
Fixes: 0ec33be4c8 ("cxgbe: allow to change mtu")
Cc: stable@dpdk.org
Signed-off-by: Steve Yang <stevex.yang@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add ethdev ops to query and configure link FEC.
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Rework and simplify link handling code. Remove redundant
variables in link configuration structure and directly
extract information from the 32-bit link capabilities.
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Remove legacy 16-bit link capabilities and always request for the
32-bit link capabilities from firmware.
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Allows i40e and mlx5 PMDs to compile on Windows and disable other drivers.
Disable few i40e warnings with Clang such as comparison of integers of
different signs and macro redefinitions.
Signed-off-by: Pallavi Kadam <pallavi.kadam@intel.com>
Reviewed-by: Ranjit Menon <ranjit.menon@intel.com>
Acked-by: Tal Shnaiderman <talshn@nvidia.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
When apps pass the RTE_FLOW_ITEM_TYPE_VLAN without setting the
ethertype field in RTE_FLOW_ITEM_TYPE_ETH, then assume 0x8100
VLAN by default and don't reject the rule.
Fixes: 55f003d888 ("net/cxgbe: support flow API for matching QinQ VLAN")
Cc: stable@dpdk.org
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Since each version map file is contained in the subdirectory of the library
it refers to, there is no need to include the library name in the filename.
This makes things simpler in case of library renaming.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Queue stats are stored in 'struct rte_eth_stats' as array and array size
is defined by 'RTE_ETHDEV_QUEUE_STAT_CNTRS' compile time flag.
As a result of technical board discussion, decided to remove the queue
statistics from 'struct rte_eth_stats' in the long term.
Instead PMDs should represent the queue statistics via xstats, this
gives more flexibility on the number of the queues supported.
Currently queue stats in the xstats are filled by ethdev layer, using
some basic stats, when queue stats removed from basic stats the
responsibility to fill the relevant xstats will be pushed to the PMDs.
During the switch period, temporary 'RTE_ETH_DEV_AUTOFILL_QUEUE_XSTATS'
device flag is created. Initially all PMDs using xstats set this flag.
The PMDs implemented queue stats in the xstats should clear the flag.
When all PMDs switch to the xstats for the queue stats, queue stats
related fields from 'struct rte_eth_stats' will be removed, as well as
'RTE_ETH_DEV_AUTOFILL_QUEUE_XSTATS' flag.
Later 'RTE_ETHDEV_QUEUE_STAT_CNTRS' compile time flag also can be
removed.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Xiao Wang <xiao.w.wang@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Change eth_dev_stop_t return value from void to int.
Make eth_dev_stop_t implementations across all drivers to return
negative errno values if case of error conditions.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The API function rte_eth_dev_close() was returning void.
The return type is changed to int for notifying of errors.
If an error happens during a close operation,
the status of the port is undefined,
a maximum of resources having been freed.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Liron Himi <lironh@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The secondary processes are not allowed to release shared resources.
Only process-private resources should be freed in a secondary process.
Most of the time, there is no process-private resource,
so the close operation is just forbidden in a secondary process.
After adding proper check in the port close functions,
some redundant checks in the device remove functions are dropped.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Reviewed-by: Sachin Saxena <sachin.saxena@oss.nxp.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Liron Himi <lironh@marvell.com>
Reviewed-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
The temporary flag RTE_ETH_DEV_CLOSE_REMOVE is removed.
It was introduced in DPDK 18.11 in order to give time for PMDs to migrate.
The old behaviour was to free only queues when closing a port.
The new behaviour is calling rte_eth_dev_release_port() which does
three more tasks:
- trigger event callback
- reset state and few pointers
- free all generic port resources
The private port resources must be released in the .dev_close callback.
The .remove callback should:
- call .dev_close callback
- call rte_eth_dev_release_port()
- free multi-port device shared resources
Despite waiting two years, some drivers have not migrated,
so they may hit issues with the incompatible new behaviour.
After sending emails, adding logs, and announcing the deprecation,
the only last solution is to declare these drivers as unmaintained:
ionic, liquidio, nfp
Below is a summary of what to implement in those drivers.
* The freeing of private port resources must be moved
from the ".remove(device)" function to the ".dev_close(port)" function.
* If a generic resource (.mac_addrs or .hash_mac_addrs) cannot be freed,
it must be set to NULL in ".dev_close" function to protect from
subsequent rte_eth_dev_release_port() freeing.
* Note 1:
The generic resources are freed in rte_eth_dev_release_port(),
after ".dev_close" is called in rte_eth_dev_close(), but not when
calling ".dev_close" directly from the ".remove" PMD function.
That's why rte_eth_dev_release_port() must still be called explicitly
from ".remove(device)" after calling the ".dev_close" PMD function.
* Note 2:
If a device can have multiple ports, the common resources must be freed
only in the ".remove(device)" function.
* Note 3:
The port is supposed to be in a stopped state when it is closed.
If it is not the case, it is free to the PMD implementation
how to react when trying to close a non-stopped port:
either try to stop it automatically or just return an error.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Liron Himi <lironh@marvell.com>
Reviewed-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
The device operation .dev_close was returning void.
This driver interface is changed to return an int.
Note that the API rte_eth_dev_close() is still returning void,
although a deprecation notice is pending to change it as well.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Reviewed-by: Sachin Saxena <sachin.saxena@oss.nxp.com>
Reviewed-by: Liron Himi <lironh@marvell.com>
Reviewed-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Jeff Guo <jia.guo@intel.com>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Chelsio T6 NIC can support up to 8 priority channels to manage
congestion. So, increase to 8 congestion channels for T6. Also,
add Rxq state to avoid unnecessarily ringing doorbell and polling
the hardware for more traffic when the Rxq is stopped.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Firmware returns the max queues that can be allocated on the entire
PF. The driver evenly distributes them across all the ports belonging
to the PF. However, some ports may need more queues than others and
this equal distribution scheme prevents accessing these other ports
unused queues. So, remove the equal distribution scheme and allow the
ports to allocate as many queues as they need.
Also remove the hardcoded 64 max limit on queue allocation. Instead,
use the max limit given by firmware.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Enable RTE_ETH_DEV_CLOSE_REMOVE during PCI probe for all ports
enumerated under the PF. Free up the underlying port Virtual
Identifier (VI) and associated resources during port close.
Once all the ports under the PF are closed, free up the PF-wide
shared resources. Invoke port close function of all ports under
the PF, in PCI remove too.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Free up the DMA memzones properly for all the port's queues during
port close. So, rework DMA ring allocation/free logic to use
rte_eth_dma_zone_reserve()/rte_eth_dma_zone_free() helper functions
for allocating/freeing the memzones.
The firmware event queue doesn't have an associated freelist queue.
So, remove check that tries to give memzone name for a non-existent
freelist queue.
Also, add a missing free for the control queue mempools.
Fixes: 0462d11544 ("cxgbe: add device related operations")
Cc: stable@dpdk.org
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Ensure packets are available before accessing the mbuf list in Tx
burst function. Otherwise, just reclaim completed Tx descriptors and
exit.
Fixes: b1df19e43e ("net/cxgbe: fix prefetch for non-coalesced Tx packets")
Cc: stable@dpdk.org
Reported-by: Brian Poole <brian90013@gmail.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
During MAC address insertion to MPS TCAM, add a default mask when
the mask is not explicitly specified. Otherwise, driver misses the
mask comparison and ends up inserting duplicate entries in the
MPS TCAM.
Fixes: 6fda3f0ddd ("net/cxgbe: add API to program hardware MPS table")
Cc: stable@dpdk.org
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
A decision was made [1] to no longer support Make in DPDK, this patch
removes all Makefiles that do not make use of pkg-config, along with
the mk directory previously used by make.
[1] https://mails.dpdk.org/archives/dev/2020-April/162839.html
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Start a new release cycle with empty release notes.
The ABI version becomes 21.0.
The ABI major is back to normal, having only one number (21 vs 20.0).
The map files are updated to the new ABI major number (21).
The ABI exceptions are dropped.
Travis ABI check is disabled because compatibility is not preserved.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Ray Kinsella <mdr@ashroe.eu>
Introduce the RTE_LOG_REGISTER macro to avoid the code duplication
in the logtype registration process.
It is a wrapper macro for declaring the logtype, registering it and
setting its level in the constructor context.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Adam Dybkowski <adamx.dybkowski@intel.com>
Acked-by: Sachin Saxena <sachin.saxena@nxp.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
Disable all unused firmware resources during init time to give
more resources for HASH (exact-match) filter region and always
request firmware to enable HASH filter support when resources
are available.
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
commit 536db938a4 ("net/cxgbe: add devargs to control filtermode and
filtermask") allows configuring hardware to select specific combination
of header fields to match in the incoming packets. However, the default
mask is set for all fields in the requested pattern items, even if the
field is not explicitly set in the combination and results in
validation errors. To prevent this, ignore setting the default masks
for the unrequested fields and the hardware will also ignore them in
validation, accordingly. Also, tweak the filter spec before finalizing
the masks.
Fixes: 536db938a4 ("net/cxgbe: add devargs to control filtermode and filtermask")
Cc: stable@dpdk.org
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Free up Source MAC Table (SMT) entry properly during filter create
failure and filter delete.
Fixes: 993541b2fa ("net/cxgbe: support flow API for source MAC rewrite")
Cc: stable@dpdk.org
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
The Multi Port Switch (MPS) entry is allocated twice when both
flow validate and create are invoked, but only freed once during
flow destroy. Avoid double alloc by moving MPS entry allocation
closer to when the filter create request is sent to hardware and
will be ignored for filter validate request.
Fixes: fefee7a619 ("net/cxgbe: add flow ops to match based on dest MAC")
Cc: stable@dpdk.org
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Free up Compressed Local IP (CLIP) entry properly during filter
creation failure path. Also consolidate all various tables
cleanup to a common function and invoke it from both wild-card
and exact-match filter paths.
Fixes: af44a57798 ("net/cxgbe: support to offload flows to HASH region")
Cc: stable@dpdk.org
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Apart from the 4-tuple (IP src/dst addresses and TCP/UDP src/dst
port addresses), there are only 40-bits available to match other
fields in packet headers. Not all combinations of packet header
fields can fit in the 40-bit tuple.
Currently, the combination of packet header fields to match are
configured via filterMode for LETCAM filters and filterMask for
HASH filters in firmware config files (t5/t6-config.txt). So, add
devargs to allow User to dynamically select the filterMode and
filterMask combination during runtime, without having to modify the
firmware config files and reflashing them onto the adapter. A table
of supported combinations is maintained by the driver to internally
translate the User specified devargs combination to hardware's internal
format before writing the requested combination to hardware
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Add new firmware API FW_PARAM_DEV_FILTER_MODE_MASK to fetch
the filtermode and filtermask values configured in hardware,
which are used to validate the match combinations in the filter
spec before offloading the filter rules to hardware. For older
firmware that doesn't support the new API, fallback to older way
of directly reading from indirect registers
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Add support to rewrite Source MAC addresses. The new Source
MAC address is written into a free entry in the SMT table
and the corresponding SMT index is used by hardware to
rewrite the Source MAC address of the packets hitting the
flow.
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Source MAC Table (SMT) is used for storing Source MAC
addresses to be written in packets transmitted on the
wire. Hence, the SMT table can be used for overwriting
Source MAC addresses in packets, hitting corresponding
filter rules inserted by the rte_flow API.
Query firmware for SMT start and size information available
to the underlying PF. Allocate and maintain the corresponding
driver's copy of the hardware SMT table, with appropriate
refcount mechanism. If SMT information is not available, then
use the entire hardware SMT table.
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Add support for overwriting destination MAC addresses.
The new MAC address is written into a free entry in the
L2T table and the corresponding L2T index is used by
hardware to overwrite the destination MAC address of the
packets hitting the flow
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Add support to match all packets received on the underlying VF.
Use new firmware API to fetch the Virtual Interface Number (VIN)
allocated to each VF by the firmware. The VIN is required to
write filter rules to match all packets on VFs, whose identifier
is beyond max 7-bit value (i.e. 127) in VIID.
If firmware doesn't support fetching the VIN information, then
fallback to manually retrieving the VIN value from the 7-bit field
in the VIID, which only supports in range of 0..127. In this case,
packets belonging to VFs, whose identifier is beyond 127 can't be
matched.
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Add support to match all packets received on the underlying PF
Note that the same 17-bit hardware tuple is shared between QinQ
and PF match. Hence, match on either QinQ or PF only can be done
at a time. Both QinQ and PF match can't be enabled at the same time.
Also, remove check to reject rules without spec because
RTE_FLOW_ITEM_TYPE_PF doesn't require a spec. Due to this check
removal, RTE_FLOW_ITEM_TYPE_PHY_PORT item needs to be updated to
handle NULL spec
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Add support to match Type of Service (TOS) field in
IPv4/IPv6 header
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Add support to match fields in 802.1ad Q-in-Q VLAN packets.
Relax check for repeated pattern items for RTE_FLOW_ITEM_TYPE_VLAN
item, since the same item is used to represent both QinQ and VLAN
packets.
When QinQ match is enabled, the ethertype field in the hardware
spec must contain the innermost VLAN header's ethertype field,
and not the Ethernet header's ethertype field. The hardware
automatically searches for ethertype 0x88A8/0x8100 in Ethernet
header, when parsing incoming packet against QinQ/VLAN pattern,
respectively.
Signed-off-by: Karra Satwik <kaara.satwik@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Multi-segs Tx is already supported by CXGBE PMD. So, add the missing
DEV_TX_OFFLOAD_MULTI_SEGS flag to the list of supported Tx offload
features.
Fixes: 436125e641 ("net/cxgbe: update to Rx/Tx offload API")
Cc: stable@dpdk.org
Reported-by: Chas Williams <3chas3@gmail.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Replace 'typedef int bool' with 'stdbool.h' to avoid possible
multiple definitions of 'bool'.
Signed-off-by: Dharmik Thakkar <dharmik.thakkar@arm.com>
Reviewed-by: Phil Yang <phil.yang@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Merge all versions in linker version script files to DPDK_20.0.
This commit was generated by running the following command:
:~/DPDK$ buildtools/update-abi.sh 20.0
Signed-off-by: Pawel Modrak <pawelx.modrak@intel.com>
Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Since the library versioning for both stable and experimental ABI's is
now managed globally, the LIBABIVER and version variables no longer
serve any useful purpose, and can be removed.
The replacement in Makefiles was done using the following regex:
^(#.*\n)?LIBABIVER\s*:=\s*\d+\n(\s*\n)?
(LIBABIVER := numbers, optionally preceded by a comment and optionally
succeeded by an empty line)
The replacement for meson files was done using the following regex:
^(#.*\n)?version\s*=\s*\d+\n(\s*\n)?
(version = numbers, optionally preceded by a comment and optionally
succeeded by an empty line)
[David]: those variables are manually removed for the files:
- drivers/common/qat/Makefile
- lib/librte_eal/meson.build
[David]: the LIBABIVER is restored for the external ethtool example
library.
Signed-off-by: Anatoly Burakov <anatoly.burakov@intel.com>
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
By default RSS hash delivery (offload) is bound to RSS mode and
it is incorrect to advertise it as enabled if Rx multi-queue mode
has no RSS.
Fixes: 8b945a7f7d ("drivers/net: update Rx RSS hash offload capabilities")
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add DEV_RX_OFFLOAD_RSS_HASH flag for all PMDs that support RSS hash
delivery.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
When rules are being inserted from multiple cores, there are several
race conditions during rte_flow operations.
For example, when inserting rules from 2 cores simultaneously, both
the cores try to fetch a free available filter entry and they both
end up fetching the same entry. Both of them start overwriting the
same filter entry before sending to firmware, which results in wrong
rule being inserted to hardware.
Fix the races by adding spinlock to serialize the rte_flow operations.
Fixes: ee61f5113b ("net/cxgbe: parse and validate flows")
Fixes: 9eb2c9a480 ("net/cxgbe: implement flow create operation")
Fixes: da23bc9d33 ("net/cxgbe: implement flow destroy operation")
Fixes: 8d3c12e193 ("net/cxgbe: implement flow query operation")
Fixes: 86910379d3 ("net/cxgbe: implement flow flush operation")
Cc: stable@dpdk.org
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
