The UNMAINTAINED flag will be removed in a future patch.
Signed-off-by: Andrew Boyer <aboyer@pensando.io>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Added VLAN support for AMD XGBE driver
Adding below APIs for axgbe
- axgbe_enable_rx_vlan_stripping: to enable vlan header stripping
- axgbe_disable_rx_vlan_stripping: to disable vlan header stripping
- axgbe_enable_rx_vlan_filtering: to enable vlan filter mode
- axgbe_disable_rx_vlan_filtering: to disable vlan filter mode
- axgbe_update_vlan_hash_table: crc calculation and hash table update
based on vlan values post filter enable
- axgbe_vlan_filter_set: setting of active vlan out of max 4K values
before doing hash update of same
- axgbe_vlan_tpid_set: setting of default tpid values
- axgbe_vlan_offload_set: a top layer function to call strip/filter etc
based on mask values
Signed-off-by: Girish Nandibasappa <girish.nandibasappa@amd.com>
Acked-by: Somalapuram Amaranath <asomalap@amd.com>
Since the hns3 NIC hardware features are not counted
and it is supported in fact. Besides, the flow director
is not supported and need to delete it.
Fixes: fa29fe45a7b4 ("net/hns3: support queue start and stop")
Fixes: 521ab3e93361 ("net/hns3: add simple Rx path")
Fixes: bba636698316 ("net/hns3: support Rx/Tx and related operations")
Fixes: 936eda25e8da ("net/hns3: support dump register")
Fixes: 53b9f2b9a560 ("doc: update feature list in hns3 guide")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
The ARMv8 platform support was tested and works fine with the ENA PMD.
It can be used on the AWS a1.* and m6g.* instances.
The ARMv8 support in ENA is at least from v19.11, where the VFIO DPDK
driver was fixed to work with 32-bit applications compiled for arm.
Signed-off-by: Michal Krawczyk <mk@semihalf.com>
Reviewed-by: Igor Chauskin <igorch@amazon.com>
Reviewed-by: Guy Tzalik <gtzalik@amazon.com>
Supports check the status of Rx and Tx descriptors.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Mark "BSD nic_uio", "Usage doc", and "Perf doc" as supported
for the bnxt PMD.
Signed-off-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add RSS configure, support to RSS hash and reta operations for PF.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add packet type marco definition and convert ptype to ptid.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add receive and transmit units start and stop for specified queue.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Adding bare minimum PMD library and doc build infrastructure
and claim the maintainership for txgbe PMD.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add support for DEV_TX_OFFLOAD_MBUF_FAST_FREE to bnxt
vector mode transmit. This offload may be enabled
only when multi-segment transmit is not needed, all
transmitted mbufs for a given queue will be allocated
from the same pool, and all transmitted mbufs will
have a reference count of 1.
Signed-off-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The new generation hns3 network engine supports independent enabling and
disabling of a single Tx/Rx queue. So, it can support the queue start
and stop feature. In addition, when different numbers of Tx and Rx
queues need to be enabled in some applications, hns3 pmd does not need
to create fake queues to enable these scenarios.
This patch Add queue start and stop feature for the new generation hns3
networking engine. Cancel the creation of fake queue on the new
generation network engine. And the previously improperly named queue
related function was renamed to improve readability.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds required bit to handle VF FLR
indication from Management FW (MFW) of the device
With that VFs were able to load in VM (VF attached as PCI
passthrough to the guest VM) followed by FLR successfully
Updated the docs/guides with the feature support
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Rasesh Mody <rmody@marvell.com>
When PF event VIRTCHNL_EVENT_LINK_CHANGE received, i40evf need update
the link status and issue RTE_ETH_EVENT_INTR_LSC via rte ether device
callback function.
Signed-off-by: Steve Yang <stevex.yang@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
DEV_RX_OFFLOAD_TIMESTAMP is per port, so the internal implementation
shall enable it on per port basis only.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Add support for .get_reg eth_dev ops which will be used to collect the
firmware debug data.
PMD on detecting on some HW errors will collect the FW/HW Dump to a
buffer and then it will save it to a file implemented in
qede_save_fw_dump().
Dump file location and name:
Location: <RTE_SDK> or DPDK root
Name: qede_pmd_dump_mm-dd-yy_hh-mm-ss.bin
DPDK applications can initiate a debug data collection by invoking DPDK
library’s rte_eth_dev_get_reg_info() API. This API invokes .get_reg()
interface in the PMD.
PMD implementation of .get_reg() collects the FW/HW Dump, saves it to
data field of rte_dev_reg_info and passes it to the application. It’s
the responsibility of the application to save the FW/HW Dump to a file.
We recommendation using the file name format used by qede_save_fw_dump().
Signed-off-by: Rasesh Mody <rmody@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Dynamic flow used instead of layout defined.
The actual key/mask size depends on protocols and(or) fields
of patterns specified.
Also, the key and mask should start from the beginning of IOVA.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Enable/disable link state interrupt and get link state api is
defined using IOCTL calls from kernel driver
Signed-off-by: Rohit Raj <rohit.raj@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
This patch adds 'Scattered Rx' and 'Multiprocess aware' those are
supported by current hns3 PMD driver for feature list file named
hns3.ini and hns3_vf.ini.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds support of LRO offload for hns3 PMD driver.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
