bus driver will now remember the size of a BAR obtained during the initial
bus scan and use that size when doing lazy resource allocation rather than
resizing the BAR. The bus driver will now also report unallocated BARs to
userland for display by 'pciconf -lb'. Psuedo-resources that are not BARs
(such as the implicit I/O port resources for master/slave ATA controllers)
will no longer be listed as BARs in 'pciconf -lb'. During resume, BARs are
restored from their new saved state instead of having the raw registers
saved and restored across resume. This also fixes restoring BARs at
unusual loactions if said BAR has been allocated by a driver.
Add a constant for the offset of the ROM BIOS BAR in PCI-PCI bridges and
properly handle ROM BIOS BARs in PCI-PCI bridges. The PCI bus now also
properly handles the lack of a ROM BIOS BAR in a PCI-Cardbus bridge.
Tested by: jkim
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
in the RX path when doing 11n and block-ack'ed frames. Apparently, the MAC
will loop over that self-linked descriptor and treat it as "good enough"
for (incorrectly!) ACKing the frames in the block-ack.
Until I figure out how to work around this issue in the future, this counter
will tell me if packet RX processing ever gets to the point where it's
touching the self-linked descriptor. If there's ever enough packets to get
to that point, BA's will be invalid and likely very unhappy.
of active DMA cycle. dc_setcfg() also has to wait until the DMA
engine is stopped so using a common function to handle the job is
better than duplicating the code.
No objection from: marius
makes controller to receive bad frames and i82557 will also receive
bad frames since fxp(4) have to receive VLAN oversized frames. If
fxp(4) encounter DMA overrun error, the received frame size would
be 0 so the actual frame size after checksum field extraction the
length would be negative(-2). Due to signed/unsigned comparison
used in driver, frame length check did not work for DMA overrun
frames. Correct this by casting it to int.
While I'm here explicitly check DMA overrun error and discard the
frame regardless of result of received frame length check.
Reported by: n_hibma
Tested by: n_hibma
MFC after: 1 week
I'll clear how it's supposed to work with Bernhard and then look
at enabling this in the correct situations.
But this -does- enable HT RTS protection (using the appropriate legacy
rates) if this bit of code is enabled.
by default.
Adventourous souls with an AR9220/AR9280 or later and who have a device
that sends PS-POLL frames may wish to try tinkering with this option and
get back to me.
Linux ath9k only enables this for AR9280 and later NICs; so
create a capability for it so it isn't enabled for earlier
NICs.
Enabling hardware PS-POLL support will come in a later commit
and will be disabled by default.
Even though they map to setting the error filter register,
ath9k also writes them untouched to AR_RX_FILTER.
The Force-BSSID match bit can stay high, as it maps to a
misc mode register setting rather than an RX filter bit.
The phyerr, radar and bssid-match bits aren't real bits, they map
to enabling bits in other registers. Move those out of the way of
valid RX filter bits.
Add a few new fields from ath9k - compba, ps-poll, mcast-bcast-all.
Changes since 7.8.0 (from the official changelog):
- Fixed sporadic interrupt generation for associated CQ when processing
a local invalidate work request
- Changes to core scheduling to avoid starving requests from the host
under heavy RDMA Read Request load (e.g. packets to the wire)
- Programmed the tp tx resource limiter in function of the traffic (only
affects iWarp)
- Increased the egress NIC gather list length from 36 to 46 entries
MFC after: 1 week
the channel width is ni->ni_chw, which is set to the negotiated channel
width. ni->ni_htflags is the capability, rather than the negotiated
value.
Teach both the TX path and the sample rate module about this.
This seems to work fine for STA but not HT/20 AP mode.
Further discussion with net80211 people will need to take place
to ensure that the right flags are set based on the negotiated
capabilities of the remote peer, rather than whatever the local
parameters are.
Sending short-gi frames in 20mhz may work on some chips but
it certainly isn't supported on anything currently supported
by the HAL; and sending HT40 frames in HT20 mode just plain
won't work.
settings, it seems that our defines are backwards and don't match what
is in the EEPROM documentation or internal driver.
The ath9k code used to have a bitfield here, rather than a uint8_t, and
there were #defines used to swap the order based on the endian of the
platform - this wasn't because of nybble or bit ordering of the
underlying host but because of what the compiler was doing.
This may be the reason for the backwards field numbers, as ath9k had
similar issues.
the AR9285 so I'll leave it off for that.
Ath9k sources indiciate that one of the ANI modes interferes with
RIFS detection, so match ath9k and disable that.
* The existing interrupt mitigation code didn't mitigate anything - the
per-packet TX/RX interrupts are still occuring. It's possible this
worked for the AR5416 but not any later chipsets; I'll investigate and
update as needed.
* Set both the RX and TX threshold registers whilst I'm at it.
This is verified to work on the AR9220 and AR9160. I'm leaving it off
by default in case it's truely broken, but I need to have it enabled
when doing 11n testing or interrupt loads exceed 10,000 interrupts/sec.
queue has its own interrupt. If the exact number that we need is not a
power of 2 and we're using MSI, then switch to interrupt multiplexing.
While here, replace the magic numbers with something more readable.
MFC after: 3 days
At least one AR5416 user has reported measurable throughput drops
with this option. For now, disable it and make it a run-time
twiddle. It won't take affect until the next radio programming
trip though (eg channel scan, channel change.)
so there's no need to enable the RX of invalid frames just to do ANI.
The if_ath code and AR5212 ANI code setup the RX filter bits to enable
receiving OFDM/CCK errors if the device doesn't have the hardware
MIB counters. It isn't initialising it for the AR5416+ because all of
those chips have hardware MIB counters.
This fixes the odd (and performance affecting!) situation where if ani
is enabled (via sysctl dev.ath.X.intmit) then suddenly there's be a very
large volume of phy errors - which is good to track, but not what was
intended. Since each PHY error is a received (0 length) frame, it can
significantly tie up the RX side of things.
It's still not ready for prime-time - there's some TX niggles with these 11n
cards that I'm still trying to wrap my head around, and AMPDU-TX is just not
implemented so things will come to a crashing halt if you're not careful.
"extended capabilities" to refer to the new set of capability structures
starting at offset 0x100 in config space for PCI-express devices. For now
both function names will still work. I will merge this to older branches
to ease driver portability, but 9.0 will ship with a new pci_find_extcap()
function that locates extended capabilities instead.
Reviewed by: imp
MFC after: 1 week
This fix modifies the const addac initval array, rather than modifying
a local copy. It means that running >1 AR9160 on a board may prove to
be unpredictable.
The AR5416 init path also does something similar, so supporting
>1 AR5416 of different revisions could cause problems.
The later fix will be to create a private copy of the Addac data
for the AR5416, AR9160 (and AR9100 when it's merged in) and then
modify that as needed.
Obtained From: Linux ath9k
I found this when trying to figure out why the RX PHY error count
didn't match the OFDM error count ANI was using. It turns out
there was two problems:
* What this commit addresses - using the wrong mask for OFDM errors,
and
* The RX filter is set incorrectly after a channel scan (at least)
even if interference mitigation is enabled by default.
ANI is still disabled by default for the AR5416 and later chips.
bring it in line with the rest of the register initialisation.
I've verified that the 2/5ghz board values written to the
chip match what was previously written.
* add pspoll/uapsd queue setup defaults;
* enable the exponential backoff window rather than the random
backoff window when doing TX contention management.
would be a problem, make sure it isn't overwritten by whatever is in
there at cold reset.
This brings the > ar5416 init path treatment of AR_MISC_MODE.
report descriptor information, sysctl utility
will show it for us.
- Modify sysctl node description to make it more
understanable.
Found by: Alexander Best <arundel@freebsd.org>
Submitted by: Eygene Ryabinkin <rea@freebsd.org>
MFC after: 14 days
Approved by: thompsa (mentor)
value is updated after that we read it in the queue-head. This patch can
fix problems with BULK timeouts. The issue was found on a Nvidia chipset.
MFC after: 14 days
Approved by: thompsa (mentor)
* Pull out the static rix stuff into a different function
* I know this may slightly drop performance, but check if a static
rix is needed before each packet TX.
* Whilst I'm at it, add a little extra debugging to the rate
control stuff to make it easier to follow what's going on.
Give it a good go (32 attempts) and then print out a warning that's
going to occur whether HAL debugging is enabled or not. Then don't
abort the radio setup; just continue merrily along.
This should fix the issue that users were having where scanning would
occasionally fail on the active channel, causing traffic to cease
until the radio scanned again.
not needed.
These calibrations are only applicable if the chip operating mode
engages both interleaved RX ADCs (ie, it's compensating for the
differences in DC gain and DC offset -between- the two ADCs.)
Otherwise the chip reads values of 0x0 for the secondary ADC
(as I guess it's not enabled here) and thus writes potentially
bogus info into the chip.
I've tested this on the AR9160 and AR9280; both behave themselves
in 11g mode with these calibrations disabled.
for fixing them based on the ath9k related TXQ fixes.
I've done this so people can go over the history of the diffs to the original
AR5212 routines (which AR5416 and later chips use) to see what's changed.
enables broadcast filtering. Make sure to clear the bit to receive
broadcast frames. While I'm here rename the bit definition to
reflect reality.
Reported by: brad@OpenBSD
MFC after: 1 week
This commit really is "fix the OFDM duration calculation to match reality when
running in 802.11g mode."
The AR5212 init vals set AR_MISC_MODE to 0x0 and all the bits that can be set are
set through code.
The AR5416 and later initvals set AR_MISC_MODE to various other values (with
the AR5212 AR_MISC_MODE options cleared), which include AR_PCU_CCK_SIFS_MODE .
This adds 6uS to SIFS on non-CCK frames when transmitting.
This fixes the issue where _DATA_ 802.11g OFDM frames were being TX'ed with
the ACK duration set to 38uS, not 44uS as on the AR5212 (and other devices.)
The AR5212 TX pathway obeys the software-programmed duration field in the packet,
but the 11n TX pathway overrides that with a hardware-calculated duration. This
was getting it wrong because of the above AR_MISC_MODE setting. I've verified
that 11g data OFDM frames are now being TXed with the correct ACK+SIFS duration
programmed in.
Since ath9k does some slightly different bit fiddling when setting up
the TX queues, it may that the TX queue setup/reset functions will need
overriding later on.
been undergoing test for some weeks. This improves the RX
mbuf handling to avoid system hang due to depletion. Thanks
to all those who have been testing the code, and to Beezar
Liu for the design changes.
Next the igb driver is updated for similar RX changes, but
also to add new features support for our upcoming i350 family
of adapters.
MFC after a week
chipsets that do not have an HT slave at 0:0:0:0. The Linux quirk is
actually specific to Nvidia chipsets and the check I had added was in
the wrong place.
Prodded by: nathanw
- Always enable the HyperTransport MSI mapping window for HyperTransport
to PCI bridges (these show up as HyperTransport slave devices).
The mapping windows in PCI-PCI bridges are enabled by existing code
in the PCI-PCI bridge driver as MSI requests propagate up the device
tree, but Host-PCI bridges don't really show up in that tree.
- If the PCI device at domain 0 bus 0 slot 0 function 0 is not a
HyperTransport device, then blacklist MSI on any other HT devices in
the system. Linux has a similar quirk.
PR: kern/155442
Tested by: Zack Dannar zdannar of gmail
MFC after: 1 week
With this change, driver may not notice updated descriptor status
change when bounce buffers are active. However, rxeof() in next run
will handle the synchronization.
Change dc_rxeof() a bit to return the number of processed frames in
RX descriptor ring. Previously it returned the number of frames
that were successfully passed to upper stack which in turn means it
ignored frames that were discarded due to errors. The number of
processed frames in RX descriptor ring is used to detect whether
driver is out of sync with controller's current descriptor pointer.
Returning number of processed frames reduces unnecessary (probably
wrong) re-synchronization.
Reviewed by: marius
This does a few things in particular:
* Abstracts out the gain control settings into a separate function;
* Configure antenna diversity, LNA and antenna gain parameters;
* Configure ob/db entries - the later v4k EEPROM modal revisions have
multiple OB/DB parameters which are used for some form of
calibration. Although the radio does have defaults for each,
the EEPROM can override them.
This resolves the AR2427 related issues I've been seeing and makes
it stable at all 11g rates for both TX and RX.
The offsets didn't match the assumption that nfarray[] is ordered by the
chainmask bits and programmed via the register order in ar5416_cca_regs[].
This repairs that damage and ensures that chain 1 is programmed correctly.
(And extension channels will now be programmed correctly also.)
This fixes some of the stuck beacons I've been seeing on my AR9160/AR5416
setups - because Chain 1 would be programmed -80 or -85 dBm, which is
higher than the actual noise floor and thus convincing the radio that
indeed it can't ever transmit.
rather than duplicating them for the v14 (ar5416+) and v4k (ar9285) codebases.
Further chipsets (eg the AR9287) have yet another EEPROM format which will use
these routines to calculate things.
to the TX closed-loop power control registers.
* Modify a couple of functions to take the register chain number,
rather than the regChainOffset value. This allows for the
register chain to be logged.
also does this for sound drivers it's probably not necessary for all
combinations of controllers and drivers. However, given that our sound
drivers completely lack bus_dmamap_sync(9) calls this at least serves
as a workaround when enabling use of the IOMMU streaming buffers on
sparc64 and generally for arm and mips.
MFC after: 2 weeks
