operation. Previously ownership was transferred to hardware before
setting address of new RX buffer such that it was possible for
hardware to use wrong RX buffer address.
While here keep compiler from re-ordering instructions by declaring
descriptor members volatile. Memory barriers would do the same job
but volatile is supposed to be cheaper than using memory barriers,
especially on MP systems.
Submitted by: marius
MFC after: 1 week
mps.c: Hide the 'out of chain frames' warning behind MPS_INFO.
mps_sas.c: Hide the SIM queue freeze/unfreeze messages behind MPS_INFO.
mpsvar.h: Bump the number of chain frames from 1024 to 2048. From
testing, it looks like this makes it less likely that we'll
run out of chain frames, and it doesn't cost much memory
(32K).
MFC after: 3 days
means of allowing vendor specific interface class for audio and MIDI devices.
- Add new quirks for this. The vendor and product list in OpenBSD's
dev/usb/umidi_quirks.c was used as reference.
MFC after: 14 days
Approved by: thompsa (mentor)
causing the size calculation to be truncated to the size of an int
(32-bits on all current architectures).
Submitted by: Anish akgupt3 of gmail
MFC after: 1 week
link flips during alias address insertion or dhclient operation.
While I'm here remove dc_reset() in DC_ISR_BUS_ERR case. Device is
fully reinitialized again in dc_init_locked().
* Turn ath_tx_calc_ctsduration() into a function that
returns the ctsduration, or -1 for HT rates;
* add a printf() to ath_tx_calc_ctsduration() which will be
very loud if somehow that function is called with an MCS
rate;
* Add ath_tx_get_rtscts_rate() which returns the RTS/CTS
rate to use for the given data rate, incl. the short
preamble flag;
* Only call ath_tx_calc_ctsduration() for non-11n chipsets;
11n chipsets don't require the rtscts duration to be
calculated.
It's used to calculate:
* the initial per-rate entries for short/long preamble ACK durations;
* packet durations for TDMA slot decisions;
* RTS/CTS protection durations;
* updating the duration field in the 802.11 frame header
This way invalid durations will generate a warning, prompting for it to be
fixed.
respectively and fix all bus_dma(9) issues seen when bounce buffers
are used.
o Setup frame handling had no bus_dmamap_sync(9) which prevented
driver from configuring RX filter. Add missing bus_dmamap_sync(9)
in both dc_setfilt_21143()/dc_setfilt_xircom() and dc_txeof().
o Use bus_addr_t for DMA segment instead of using u_int32_t.
o Introduce dc_dma_alloc()/dc_dma_free() functions to allocate/free
DMA'able memory.
o Create two DMA descriptor list for each TX/RX lists. This change
will minimize the size of bounce buffers that would be used in
each TX/RX path. Previously driver had to copy both TX/RX lists
when bounce buffer is active.
o 21143 data sheet says descriptor list requires 4 bytes alignment.
Remove PAGE_SIZE alignment restriction and use
sizeof(struct dc_dec).
o Setup frame requires 4 bytes alignment. Remove PAGE_SIZE
alignment restriction and use sizeof(struct dc_dec).
o Add missing DMA map unload for both setup frame and TX/RX
descriptor list.
o Overhaul RX handling logic such that make driver always allocate
new RX buffer with dc_newbuf(). Previously driver allowed to
copy received frame with m_devget(9) after passing the
descriptor ownership to controller. This can lead to passing
wrong frame to upper stack.
o Introduce dc_discard_rxbuf() which will discard received frame
and reuse loaded DMA map and RX mbuf.
o Correct several wrong bus_dmamap_sync(9) usage in dc_rxeof and
dc_txeof. The TX/RX descriptor lists are updated by both driver
and HW so READ/WRITE semantics should be used.
o If driver failed to allocate new RX buffer, update if_iqdrops
counter instead of if_ierrors since driver received the frame
without errors.
o Make sure to unload loaded setup frame DMA map in dc_txeof and
clear the mark of setup frame of the TX descriptor in dc_txeof().
o Add check for possible TX descriptor overruns in dc_encap() and
move check for free buffer to caller, dc_start_locked().
o Swap the loaded DMA map and the last DMA map for multi-segmented
frames. Since dc_txeof() assumes the last descriptor of the
frame has the DMA map, driver should swap the first and the last
DMA map in dc_encap(). Previously driver tried to unload
not-yet-loaded DMA map such that the loaded DMA map was not
unloaded at all for multi-segmented frames.
o Rewrite DC_RXDESC/DC_TXDESC macro to simpler one.
o Remove definition of ETHER_ALIGN, it's already defined in
ethernet.h.
With this changes, dc(4) works with bounce buffers and it shall
also fix issues which might have shown in PAE environments.
Tested by: marius
Previously dc(4) always checked whether there is pending interrupts
and this consumed a lot of CPU cycles in interrupt handler. Limit
the number of processing for TX/RX frames to 16. Also allow sending
frames in the loop not to starve TX under high RX load.
Reading DC_ISR register should be protected with driver lock,
otherwise interrupt handler could be run(e.g. link state change)
before the completion of dc_init_locked().
While I'm here remove unneeded code.
as well as controller has enough free TX descriptors.
Remove check for number of queued frames before attempting to
transmit. I guess it was added to allow draining queued frames
even if there is no link. I'm under the impression this type of
check should be done in upper layer. No other drivers in tree do
that.
ownership to controller before completion of access to the
descriptor. Driver is faking up status word so it should not give
ownership to controller until it completes RX processing.
request TX completion interrupt for every 8-th frames. Previously
dc(4) requested TX completion interrupt if number of queued TX
descriptors is greater than 64. This caused a lot of TX completion
interrupt under high TX load once driver queued more than 64 TX
descriptors. It's quite normal to see more than 64 queued TX
descriptors under high TX load.
This change reduces the number of TX completion interrupts to be
less than 17k under high TX load. Because this change does not
generate TX completion interrupt for each frame, add reclaiming
transmitted buffers in dc_tick not to generate false watchdog
timeouts.
While I'm here add check for queued descriptors in dc_txeof() since
there is no more work to do when there is no pending descriptors.
When the driver ran out of DMA chaining buffers, it kept the timeout for
the I/O, and I/O would stall.
The driver was not freezing the device queue on errors.
mps.c: Pull command completion logic into a separate
function, and call the callback/wakeup for commands
that are never sent due to lack of chain buffers.
Add a number of extra diagnostic sysctl variables.
Handle pre-hardware errors for configuration I/O.
This doesn't panic the system, but it will fail the
configuration I/O and there is no retry mechanism.
So the device probe will not succeed. This should
be a very uncommon situation, however.
mps_sas.c: Freeze the SIM queue when we run out of chain
buffers, and unfreeze it when more commands
complete.
Freeze the device queue when errors occur, so that
CAM can insure proper command ordering.
Report pre-hardware errors for task management
commands. In general, that shouldn't be possible
because task management commands don't have S/G
lists, and that is currently the only error path
before we get to the hardware.
Handle pre-hardware errors (like out of chain
elements) for SMP requests. That shouldn't happen
either, since we should have enough space for two
S/G elements in the standard request.
For commands that end with
MPI2_IOCSTATUS_SCSI_IOC_TERMINATED and
MPI2_IOCSTATUS_SCSI_EXT_TERMINATED, return them
with CAM_REQUEUE_REQ to retry them unconditionally.
These seem to be related to back end, transport
related problems that are hopefully transient. We
don't want to go through the retry count for
something that is not a permanent error.
Keep track of the number of outstanding I/Os.
mpsvar.h: Track the number of free chain elements.
Add variables for the number of outstanding I/Os,
and I/O high water mark.
Add variables to track the number of free chain
buffers and the chain low water mark, as well as
the number of chain allocation failures.
Add I/O state flags and an attach done flag.
MFC after: 3 days
the controller firmware will return all of our commands. Instead, keep
track of outstanding I/Os and return them to CAM once device removal
processing completes.
mpsvar.h: Declare the new "io_list" in the mps_softc.
mps.c: Initialize the new "io_list" in the mps softc.
mps_sas.c: o Track SCSI I/O requests on the io_list from the
time of mpssas_action() through mpssas_scsiio_complete().
o Zero out the request structures used for device
removal commands prior to filling them out.
o Once the target reset task management function completes
during device removal processing, assume any SCSI I/O
commands that are still oustanding will never return
from the controller, and process them manually.
Submitted by: gibbs
MFC after: 3 days
- Use the USB stack's builtin clear-stall feature.
- Wrap some long lines.
- Use memcpy() instead of bcopy().
- Use memset() instead of bzero().
- Tested applications:
/usr/ports/audio/fluidsynth
MFC after: 7 days
Approved by: thompsa (mentor)
frame in DM910x controllers. In r67595(more than 10 years ago) it
was replaced to use "Store and Forward" mode and made controller
generate TX completion interrupt for every frame.
any other media configuration. Otherwise some 21143 controller
cannot establish a link. While I'm here remove the PHY
initialization code in dc_setcfg(). Since dc_setcfg() is called
whenever link state is changed, having the PHY initialization code
in dc_setcfg() resulted in continuous link flips.
After driver resets SIA, use default SIA transmit/receive
configuration instead of disabling autosense/autonegotiation.
Otherwise, controller fails to establish a link as well as losing
auto-negotiation capability. For manual media configuration, always
configure 21143 controller with specified media to ensure media
change. This change makes ANA-6922 establish link with/without
auto-negotiation.
While I'm here be more strict on link UP/DOWN detection logic.
Many thanks to marius who fixed several bugs in initial patch and
even tested the patch on a couple of dc(4) controllers.
PR: kern/79262
Reviewed by: marius
Tested by: marius
port, copy SROM information from base softc as well and run SROM
parser again. This change is necessary for some dual port
controllers to make dc(4) correctly detect PHY media based on first
port configuration table.
While I'm here add a check for validity of the base softc before
duplicating SROM contents from base softc. If driver failed to
attach to the first port it can access invalid area.
PR: kern/79262
Reviewed by: marius
as they're likely not entirely correct, but they give people something
to toy with to compare behaviour/performance.
Disable the anti-noise part, as this apparently interferes with
RIFS. I haven't verified this.
packet duration for the ath_rate_sample module.
This doesn't affect the packet TX at all; only how much time the
sample rate module attributes to a completed TX.
the larger, aligned write+erase sizes the driver currently implements.
This preserves write behaviour but makes the flash driver usable for things
like a read-only FFS or a geom_uzip/geom_compress .
Note that since GEOM will now return the sector size as being smaller,
writes of sector size/alignment will now fail with an EIO. Code which
writes to the flash device will have to be (for now) manually taught
about the flash write blocksize.
caused link re-negotiation whenever application joins or leaves a
multicast group. If driver is running, it would have established a
link so there is no need to start re-negotiation. The re-negotiation
broke established link which in turn stopped multicast application
working while re-negotiation is in progress.
PR: kern/154667
MFC after: 1 week
- Allocate coherent DMA memory for the request/response queue area and
and the FC scratch area.
These changes allow isp(4) to work properly on sparc64 with usage of the
IOMMU streaming buffers enabled.
Approved by: mjacob
MFC after: 2 weeks
While updating Tx stats, already freed node could be referred and cause
page fault. To avoid such panic, spool Tx stats in driver's softc. Then,
on every ratectl interval, grab node though ieee80211_iterate_nodes() and
update ratectl stats.
* Simplify some code in run_iter_func().
* Fix typo
* Use memset instead of bzero (hselasky @)
PR: kern/153938
Submitted by: PseudoCylon <moonlightakkiy@yahoo.ca>
Approved by: thompsa (mentor)
active I/O to several disks (copying large file on ZFS) causes timeout after
just a few seconds of run. Single port 88SX6111 seems like not affected.
Skip reading transferred bytes count for these controllers. It works for
88SX6111, but 88SX6145 always returns zero there. Haven't tested others,
but better to be safe.
correctly:
* pass in whether to allow the hardware to override the duration field
in the main data frame (durupdate_en) - PS_POLL frames in particular
don't have the duration bit overriden;
* there's no rts/cts duration here; that's done elsehwere
- this also includes virtualization support on these devices
Correct some vlan issues we were seeing in test, jumbo frames on vlans
did not work correctly, this was all due to confused logic around HW
filters, the new code should now work for all uses.
Important fix: when mbuf resources are depeleted, it was possible to
completely empty the RX ring, and then the RX engine would stall
forever. This is fixed by a flag being set whenever the refresh code
fails due to an mbuf shortage, also the local timer now makes sure
that all queues get an interrupt when it runs, the interrupt code
will then always call rxeof, and in that routine the first thing done
is now to check the refresh flag and call refresh_mbufs. This has been
verified to fix this type 'hang'. Similar code will follow in the other
drivers.
Finally, sync up shared code for the I350 support.
Thanks to everyone that has been reporting issues, and helping in the
debug/test process!!
Drivers which rely on net80211 to create the beacon need to call
ieee80211_beacon_update() on iv_update_beacon() calls. This is required
that certain bits, e.g. TIM, get updated. A call to ieee80211_beacon_alloc()
is not enough because it does not care about flags which can only change
during runtime. By design a beacon is supposed to be allocated only once
while moving into RUN state.
To handle all possible calls to iv_update_beacon() the run_updateslot()
function has been revived and run_updateprot() has been added.
run_updateslot() handles slot time changes and run_updateprot() changes
to protection, both can change while nodes associate/leave.
Submitted by: Alexander Zagrebin <alex at zagrebin.ru>,
PseudoCylon <moonlightakkiy atyahoo.ca>
MFC after: 3 weeks
There's still a lot of random issues to sort out with the radio side of
things and AMPDU RX handling (and completely missing AMPDU TX handling!)
but if people wish to give this a go and assist in debugging the
issues, they can define ATH_DO_11N to enable it.
I'm just re-iterating - this is here to allow people to assist in
further 11n development; it is not any indication that the 11n support
is complete and functional.
Important notes:
* This doesn't support 1-stream cards yet - (eg AR9285) - the various bits
that negotiate TX/RX MCS don't know not to try >1 stream TX or negotiate
1-stream RX; so don't enable 11n unless you've first taught the rate
control module and the net80211 stack to negotiate 1-stream stuff;
* The only rate control module minimally 11n aware is ath_rate_sample;
* ath_rate_sample doesn't know about HT/40; so airtime will be incorrectly
calculated;
* The AR9160 and AR9280 radio code is unreliable at the higher MCS rates for
some reason; this will definitely impact 11n performance;
* AMPDU-TX isn't yet implemented;
* AMPDU-RX may be a bit buggy still and will definitely suffer from the
radio unreliability mentioned above (ie, don't expect 150/300mbit
RX just yet.)
The correct bit to set is 0x1 in the high MAC address byte, not 0x80.
The hardware isn't programmed with that bit (which is the multicast
adress bit.)
The linux ath9k keycache code uses that bit in the MAC as a "this is
a multicast key!" and doesn't set the AR_KEYTABLE_VALID bit.
This tells the hardware the MAC isn't to be used for unicast destination
matching but it can be used for multicast bssid traffic.
This fixes some encryption problems in station mode.
PR: kern/154598
- use device_printf() instead of printf() to give more accurate warnings.
- use memcpy() instead of bcopy().
- add missing #if's for non-FreeBSD compilation.
Approved by: thompsa (mentor)
error address on a decoding error to unlatch it and to allow
us to print a better diagnostics message. This also has the
side effect of clearing the condition, which prevents an
interrupt storm.
Revert back to the previous method of doing it for where a node can be
identified and it's an 11n node.
I'll have to do some further research into exactly what is being messed up
with the sequence number matching and I'll then revisit this.
This doesn't yet take into account HT40 packet durations as the node info
(needed to know if it's a HT20 or HT40 node) isn't available everywhere
it needs to be.
putting descriptors (not buffers) across a 4k page boundary can cause issues.
I've not seen it in production myself but it apparently can cause problems.
So, in preparation for addressing this workaround, (re)-expose the particular
HAL capability bit which marks whether the chipset has support for cross-4k-
boundary transactions or not.
A subsequent commit will modify the descriptor allocation to avoid allocating
descriptor entries that straddle a 4k page boundary.
- entirely eliminate some calls to uio_yeild() as being unnecessary,
such as in a sysctl handler.
- move should_yield() and maybe_yield() to kern_synch.c and move the
prototypes from sys/uio.h to sys/proc.h
- add a slightly more generic kern_yield() that can replace the
functionality of uio_yield().
- replace source uses of uio_yield() with the functional equivalent,
or in some cases do not change the thread priority when switching.
- fix a logic inversion bug in vlrureclaim(), pointed out by bde@.
- instead of using the per-cpu last switched ticks, use a per thread
variable for should_yield(). With PREEMPTION, the only reasonable
use of this is to determine if a lock has been held a long time and
relinquish it. Without PREEMPTION, this is essentially the same as
the per-cpu variable.
* The existing radio config code was for the AR5416/AR9160 and missed out
on some of the AR9280 specific stuff. Include said stuff from ath9k.
* Refactor out the gain control settings into a new function, again pilfered
from ath9k.
* Use the analog register RMW macro when touching analog registers.
Obtained from: Linux ath9k
This fixes two problems -
* All packets need to be processed here, not just aggregate ones - as any
received frames (AMPDU or otherwise) in the given TID (traffic class id)
will update the sequence number and, implied with that, update the window;
* It seems there's situations where packets aren't matching a current node but
somehow need to be tracked. Thus just tag them all for now; I'll figure out
the why later.
Whilst I'm here, bump the stats counters whilst I'm at it.
This fixes AMPDU RX in my tests; the main problems now stem from what look
like PHY level error/retransmits which are impeding general throughput, incl.
AMPDU.
TX chainmask.
since the upper layers don't (yet) know about the active TX/RX chainmasks,
it can't tell the rate scenario functions what to use. I'll eventually sort
this out; this restores functionality in the meantime.
controller in question generates frames with bad IP checksum value
if packets contain IP options. For instance, packets generated by
ping(8) with record route option have wrong IP checksum value. The
controller correctly computes checksum for normal TCP/UDP packets
though.
There are two known RTL8168/8111C variants in market and the issue
I observed happened on RL_HWREV_8168C_SPIN2. I'm not sure
RL_HWREV_8168C also has the same issue but it would be better to
assume it has the same issue since they shall share same core.
RTL8102E which is supposed to be released at the time of
RTL8168/8111C announcement does not have the issue.
Tested by: Konstantin V. Krotov ( kkv <> insysnet dot ru )
This isn't strictly required to TX (at least non-agg and non-HT40,
non-short-GI) frames; but as it needs to be done anyway, just get
it done.
Linux ath9k uses the rate scenario style path for -all- packets,
legacy or otherwise. This code does much the same.
Beacon TX still uses the legacy, non-rate-scenario TX descriptor
setup. Ath9k also does this.
This 11n rate scenario path is only called for chips in the AR5416
HAL; legacy chips use the previous interface for TX'ing.
A-MPDU RX interferes with packet retransmission/reordering.
In local testing, I was seeing A-MPDU being negotiated and then
not used by the AP sending frames to the STA; the STA would then
treat non A-MPDU frames that are retransmits as out of the window
and get plain confused.
The hardware RX status descriptor has a "I'm part of an aggregate"
bit; so this should eventually be tested and then punted to the
A-MPDU reorder handling only if it has this bit set.
make use of the aac_ioctl_event callback, if aac_alloc_command fails. This
can end up in an infinite loop in the while loop in aac_release_command.
Further investigation into the issue mentioned by Scott Long [1] will be
necessary.
[1] http://lists.freebsd.org/pipermail/freebsd-current/2007-October/078740.html
The AR5416 and later TX descriptors have new fields for supporting
11n bits (eg 20/40mhz mode, short/long GI) and enabling/disabling
RTS/CTS protection per rate.
These functions will be responsible for initialising the TX descriptors
for the AR5416 and later chips for both HT and legacy frames.
Beacon frames will remain using the non-11n TX descriptor setup for now;
Linux ath9k does much the same.
Note that these functions aren't yet used anywhere; a few more framework
changes are needed before all of the right rate information is available
for TX.
function; which will be later used by the TX path to determine
whether to use the extended features or not.
* Break out the descriptor chaining logic into a separate function;
again so it can be switched out later on for the 11n version when
needed.
* Refactor out the encryption-swizzling code that's common in the
raw and normal TX path.
The higher levels (net80211, if_ath, ath_rate) need this to make correct
choices about what MCS capabilities to advertise and what MCS rates are
able to be TXed.
In summary:
* AR5416 - 2/3 antennas, 2x2 streams
* AR9160 - 2/3 antennas, 2x2 streams
* AR9220 - 2 antennas, 2x2 sstraems
* AR9280 - 2 antennas, 2x2 streams
* AR9285 - 2 antennas but with antenna diversity, 1x1 stream
- SMBus Controller
- SATA Controller
- HD Audio Controller
- Watchdog Controller
Thanks to Seth Heasley (seth.heasley@intel.com) for providing us code.
MFC after 3 days
apply AR8152 v1.0 specific initialization code. Fix this bug by
explicitly reading PCI device revision id via PCI accessor.
Reported by: Gabriel Linder ( linder.gabriel <> gmail dot com )
After inspecting the ath9k source, it seems the AR5416 and later MACs
don't take an explicit RTS/CTS duration. A per-scenario (ie, what multi-
rate retry became) rts/cts control flag and packet duration is provided;
the hardware then apparently fills in whatever details are required.
The per-rate sp/lpack duration calculation just isn't used anywhere
in the ath9k TX packet length calculations.
The burst duration register controls something different; it seems to
be involved with RTS/CTS protection of 11n aggregate frames and is set
via a call to ar5416Set11nBurstDuration().
I've done some light testing with rts/cts protected frames and nothing
seems to break; but this may break said RTS/CTS and CTS-to-self protection.
that represents the host controller. This makes the FDT PCI support
working an a bare-bones manner. This needs a lot more work, of which
the beginning are at the end of the file, compiled-out with #if 0.
The intend being that both the Marvell PCIE and Freescale PCI/PCIX/PCIE
duplicate the same platform-independent domain initialization, that
should be moved into an unified implementation in the FDT code. Handling
of resources requires help from the platform. A unified implementation
allows us to properly support PCI devices listed in the device tree and
configured according to the device tree specification.
Sponsored by: Juniper Networks
Each different radio chipset has a different "good" range of CCA
(clear channel access) parameters where, if you write something
out of range, it's possible the radio will go deaf.
Also, since apparently occasionally reading the NF calibration
returns "wrong" values, so enforce those limits on what is being
written into the CCA register.
Write a default value if there's no history available.
This isn't the case right now but it may be later on when "off-channel"
scanning occurs without init'ing or changing the NF history buffer.
(As each channel may have a different noise floor; so scanning or
other off-channel activity shouldn't affect the NF history of
the current channel.)
* I messed up a couple of things in if_athvar.h; so fix that.
* Undo some guesswork done in ar5416Set11nRateScenario() and introduce a
flags parameter which lets the caller set a few things. To begin with,
this includes whether to do RTS or CTS protection.
* If both RTS and CTS is set, only do RTS. Both RTS and CTS shouldn't be
set on a frame.
There's two reasons for this:
* the raw and non-raw TX path shares a lot of duplicate code which should be
refactored;
* the 11n-ready chip TX path needs a little reworking.
receive processing.
Remove unnecessary restrictions on the mbuf chain length built during an
LRO receive. This restriction was copied from the Linux netfront driver
where the LRO implementation cannot handle more than 18 discontinuities.
The FreeBSD implementation has no such restriction.
MFC after: 1 week
This is just the bare minimum needed to teach ath_rate_sample to try
and handle MCS rates. It doesn't at all attempt to find the best
rate by any means - it doesn't know anything about the MCS rate
relations, TX aggregation or any of the much sexier 11n stuff
that's out there.
It's just enough to transmit 11n frames and handle TX completion.
It shouldn't affect legacy (11abg) behaviour.
Obtained from: rpaulo@
This will eventually be used by rate control modules and by the TX
code for calculating packet duration when handling rts/cts protection.
Obtained from: sam@, rpaulo@, linux ath9k
covering the whole page, free the page. Otherwise, clear the region and
mark it clean. Not marking the page dirty could reinstantiate cleared
data, but it is allowed by BIO_DELETE specification and saves unneeded
write to swap.
Reviewed by: alc
Tested by: pho
MFC after: 2 weeks
The defaults enabled three chains on the AR5416 even if the card has two
chains. This restores that and ensures that only the correct TX/RX
chainmasks are used.
When HT modes are enabled, all TX chains will be correctly enabled.
This should now enable analog chain swapping with 2-chain cards.
I'm not sure if this is needed for just the AR5416 or whether
it also applies to AR9160, AR9280 and AR9287 (later on); I'll have
to get clarification.
This, along with an initval change which will appear in a subsequent commit,
fixes bus panics that I have been seing with the AR9220 on a Routerstation Pro
(AR7161 MIPS board.)
Obtained from: Linux ath9k
PR: kern/154220
sbuf_new_for_sysctl(9). This allows using an sbuf with a SYSCTL_OUT
drain for extremely large amounts of data where the caller knows that
appropriate references are held, and sleeping is not an issue.
Inspired by: rwatson
the controller has a kind of embedded controller/memory and vendor
applies a large set of magic code via undocumented PHY registers in
device initialization stage. I guess it's a firmware image for the
embedded controller in RTL8105E since the code is too big compared
to other DSP fixups. However I have no idea what that magic code
does and what's purpose of the embedded controller. Fortunately
driver seems to still work without loading the firmware.
While I'm here change device description of RTL810xE controller.
H/W donated by: Realtek Semiconductor Corp.
exact model name is not clear yet. All previous RTL8201 10/100 PHYs
used 0x8201 in MII_PHYIDR2 which in turn makes model number 0x20
but this PHY used new model number 0x08.
capability. One of reason using interrupt taskqueue in re(4) was
to reduce number of TX/RX interrupts under load because re(4)
controllers have no good TX/RX interrupt moderation mechanism.
Basic TX interrupt moderation is done by hardware for most
controllers but RX interrupt moderation through undocumented
register showed poor RX performance so it was disabled in r215025.
Using taskqueue to handle RX interrupt greatly reduced number of
interrupts but re(4) consumed all available CPU cycles to run the
taskqueue under high TX/RX network load. This can happen even with
RTL810x fast ethernet controller and I believe this is not
acceptable for most systems.
To mitigate the issue, use one-shot timer register to moderate RX
interrupts. The timer register provides programmable one-shot timer
and can be used to suppress interrupt generation. The timer runs at
125MHZ on PCIe controllers so the minimum time allowed for the
timer is 8ns. Data sheet says the register is 32 bits but
experimentation shows only lower 13 bits are valid so maximum time
that can be programmed is 65.528us. This yields theoretical maximum
number of RX interrupts that could be generated per second is about
15260. Combined with TX completion interrupts re(4) shall generate
less than 20k interrupts. This number is still slightly high
compared to other intelligent ethernet controllers but system is
very responsive even under high network load.
Introduce sysctl variable dev.re.%d.int_rx_mod that controls amount
of time to delay RX interrupt processing in units of us. Value 0
completely disables RX interrupt moderation. To provide old
behavior for controllers that have MSI/MSI-X capability, introduce
a new tunable hw.re.intr_filter. If the tunable is set to non-zero
value, driver will use interrupt taskqueue. The default value of
the tunable is 0. This tunable has no effect on controllers that
has no MSI/MSI-X capability or if MSI/MSI-X is explicitly disabled
by administrator.
While I'm here cleanup interrupt setup/teardown since re(4) uses
single MSI/MSI-X message at this moment.
ath9k does a few different things here during config - if it's an early
AR5416 with two chains, it enables all three chains for calibration and
then restores the chainmask to the original values after initial
calibration has completed.
The reason behind this commit is to begin breaking out the chainmask
configuration for this specific reason; follow-up commits will add
the chainmask restore in the ar5416Reset() routine.
recent PCIe controllers(RTL8102E or later and RTL8168/8111C or
later) supports either 2 or 4 MSI-X messages. Unfortunately vendor
did not publicly release RSS related information yet. However
switching to MSI-X is one-step forward to support RSS.
RTL8111C generated corrupted frames where TCP option header was
broken. All other sample controllers I have did not show such
problem so it could be RTL8111C specific issue. Because there are
too many variants it's hard to tell how many controllers have such
issue. Just disable TSO by default but have user override it.
* Re-do the structure size/component math to make sure the struct matches
the expected size
* Just to be clear that we care about bitmask ordering, revert my previous
change and instead define that macro if we're on big-endian.
It turns out that the V4K eeprom definitions (used by the AR9285 and
its derivatives) is wrong. These values are at least causing issues
on my AR2427.
With this fix (and initvals in a subsequent commit), the AR2427 behaves
a lot better.
Note - there's still significant drift between the ath9k v4k eeprom
init code (again, used by AR9285 and derivatives) and what's in this
tree. That needs to be investigated and resolved.
prevent sending data when CTS is de-asserted.
In uart_tty_intr(), call uart_tty_outwakeup() when the CTS signal
changed, knowing that uart_tty_outwakeup() will do the right
thing for flow control. This avoids redundant conditionals.
PR: kern/148644
Submitted by: John Wehle <john@feith.com>
MFC after: 3 days
via AHCI-like memory resource at BAR(5). Use it if BIOS was so kind to
allocate memory for that BAR. This allows hot-plug support and connection
speed reporting.
MFC after: 2 weeks
controllers. Experimentation with RTL8102E, RTL8103E and RTL8105E
showed dramatic decrement of TX completion interrupts under high TX
load(e.g. from 147k interrupts/second to 10k interrupts/second)
With this change, TX interrupt moderation is applied to all
controllers except RTL8139C+.
The linux ath9k driver and (from what I've been told) the atheros reference
driver does this; it then leaves discarding 11n frames to the 802.11 layer.
Whilst I'm here, merge in a fix from ath9k which maintains a turbo register
setting when enabling the 11n register; and remove an un-needed (duplicate)
flag setting.
The v1 and v3 interfaces returned the whole EEPROM but the v14/v4k
interfaces just returned the base header. There's extra information
outside of that which would also be nice to get access to.
The rxmonitor hook is called on each received packet. This can get very,
very busy as the tx/rx/chanbusy registers are thus read each time a packet
is received.
Instead, shuffle out the true per-packet processing which is needed and move
the rest of the ANI processing into a periodic event which runs every 100ms
by default.
value. While I'm here enable all clocks before initializing
controller. This change should fix lockup issue seen on AR8152
v1.1 PCIe Fast Ethernet controller.
PR: kern/154076
MFC after: 3 days
This is apparently an AR9285 with the 802.11n specific bits disabled.
This code is completely untested; I'm doing this in response to users
who wish to test the functionality out. It's likely as buggy as the
AR9285 support is in FreeBSD at the moment.
sys/dev/ath/ath_hal/ar5416/ is getting very crowded and further
commits will make it even more crowded. Now is a good time to
shuffle these files out before any more extensive work is done
on them.
Create an ar9003 directory whilst I'm here; ar9003 specific
chipset code will eventually live there.
with these ADC DC Gain/Offset calibrations.
The whole idea is to calibrate a pair of ADCs to compensate for any
differences between them.
The AR5416 returns lots of garbage, so there's no need to do the
calibration there.
The AR9160 returns 0 for secondary ADCs when calibrating 2.4ghz 20mhz
modes. It returns valid data for the secondary ADCs when calibrating
2.4ghz HT/40 and any 5ghz mode.
This removes the chipset-dependent TX DMA completion descriptor groveling.
It should now be (more) portable to other, later atheros chipsets when the
time comes.
The AR9100 at least doesn't have an external serial EEPROM
attached to the MAC; it instead stores the calibration data
in the normal system flash.
I believe earlier parts can do something similar but I haven't
experienced it first-hand.
This commit introduces an eepromdata pointer into the API but
doesn't at all commit to using it. A future commit will
include the glue needed to allow the AR9100 support code
to use this data pointer as the EEPROM.
the completion schedule from the hardware and returns AH_TRUE if
the hardware supports multi-rate retries (AR5212 and above); and
returns AH_FALSE if the hardware doesn't support multi-rate retries.
The sample rate module directly reads the TX completion descriptor
and extracts the TX schedule information from that. It will be
updated in a future commit to instead use this method to determine
the completion schedule.
Since we now have the source code, there's no reason to hide the diag codes
from other areas.
They live in the HAL as they form part of the HAL API and should still be treate
as "potentially flexible; don't publish as a public API." But since they're
already used as a public API (see follow-up commit), we may as well use
them in place of magic constants.
CRITICAL FIX - with stats changes the older 82598 will panic
and trash the stack on driver load, FCOE registers ONLY exist
in 82599 and must not be read otherwise.
kern/153951 - to correct incorrect media type on adapters
with pluggable modules I have eliminated the old static
table in favor of a new dynamic shared code routine. This
also has the benefit of detecting changes when a different
module is inserted.
Performance/enhancement to the Flow Director code from my
linux coworker (the developer of the code).
Fixes from Michael Tuexen - a data corruption problem on the
82599 (CRITICAL), fix so the buf size correctly adjusts as
the cluster changes, and max descriptors are set properly.
Also added 16K clusters for those REALLY big jumbos :)
In the RX path, the RX LOCK was not being released, and this
causes LOR problems. Add the code that igb already has.
Sync with in house shared code, this was necessary for the
Flow Director fix.
MFC in 2 days
reading. (This was already done for writing to a sysctl). This
requires all SYSCTL setups to specify a type. Most of them are now
checked at compile-time.
Remove SYSCTL_*X* sysctl additions as the print being in hex should be
controlled by the -x flag to sysctl(8).
Succested by: bde
for this sensor. Instead of leaving this location empty we use here
the default name 'sensor'.
Submitted by: Justin Hibbits <chmeeedalf at gmail dot com>
Approved by: nwhitehorn (mentor)
DP8381[56] and SiS 900/7016 controllers. After r212119, sis(4) no
longer reinitializes controller if ALLMULTI/PROMISC was changed.
However, RX filter handling code assumed some bits of the RX filter
is programmed by driver initialization. This caused ALLMULTI/PROMISC
configuration is ignored under certain conditions.
Fix that issue by reprogramming all bits of RX filter register.
While I'm here follow recommended RX filter programming steps
recommended by National DP8381[56] data sheet(RX filter should be
is disabled before programming).
Reported by: Paul Schenkeveld < freebsd () psconsult dot nl >
Tested by: Paul Schenkeveld < freebsd () psconsult dot nl >
MFC after: 3 days
- Remove extra unlock from end of ale_start_locked().
- Expand scope of locking in interrupt handler.
- Move ether_ifdetach() earlier and retire now-unneeded DETACH flag.
Tested by: Aryeh Friedman
Reviewed by: yongari (earlier version)
doesn't "fail", it may merely return garbage if it is not a valid ivar
for a given device. Our parent device must be a 'pcib' device, so we
can just assume it implements pcib IVARs, and all pcib devices have a
bus number.
Submitted by: clang via rdivacky
Compile sys/dev/mem/memutil.c for all supported platforms and remove now
unnecessary dev_mem_md_init(). Consistently define mem_range_softc from
mem.c for all platforms. Add missing #include guards for machine/memdev.h
and sys/memrange.h. Clean up some nearby style(9) nits.
MFC after: 1 month
This fixes hostap mode for at least ral(4) and run(4), because there is
no sufficient call into drivers which could be used initialize the node
related ratectl variables.
MFC after: 3 days
GbE controllers. It seems these controllers no longer support
multi-fragmented RX buffers such that driver have to allocate
physically contiguous buffers.
o Retire RL_FLAG_NOJUMBO flag and introduce RL_FLAG_JUMBOV2 to
mark controllers that use new jumbo frame scheme.
o Configure PCIe max read request size to 4096 for standard frames
and reduce it to 512 for jumbo frames.
o TSO/checksum offloading is not supported for jumbo frames on
these controllers. Reflect it to ioctl handler and driver
initialization.
o Remove unused rl_stats_no_timeout in softc.
o Embed a pointer to structure rl_hwrev into softc to keep track
of controller MTU limitation and remove rl_hwrev in softc since
that information is available through a pointer to structure
rl_hwrev.
Special thanks to Realtek for donating sample hardwares which made
this possible.
H/W donated by: Realtek Semiconductor Corp.
besides the duplex ones set so just comparing it with IFM_FDX may lead
to false negatives.
- Just let the default case handle all unsupported media types.
- In pnphy_status() don't unnecessarily read a register twice.
- Remove unnused macros.
MFC after: 1 week
configuration, which is used to work around issues with certain setups
(see r161237) by default, should not be triggered as it may in turn
cause harm in some edge cases.
- Even after masking the media with IFM_GMASK the result may have bits
besides the duplex ones set so just comparing it with IFM_FDX may lead
to false negatives.
- Announce PAUSE support also for manually selected 1000BASE-T, but for
all manually selected media types only in full-duplex mode. Announce
asymmetric PAUSE support only for manually selected 1000BASE-T.
- Simplify setting the manual configuration bits to only once after we
have figured them all out. This also means we no longer unnecessarily
update the hardware along the road.
- Remove a stale comment.
Reviewed by: yongari (plus additional testing)
MFC after: 3 days
besides the duplex ones set so just comparing it with IFM_FDX may lead
to false negatives.
- Simplify ciphy_service() to only set the manual configuration bits
once after we have figured them all out. This also means we no longer
unnecessarily update the hardware along the road.
MFC after: 1 week
complicates the code.
- Don't let atphy_setmedia() announce PAUSE support for half-duplex when
MIIF_FORCEPAUSE is set.
- Simplify e1000phy_service() and ip1000phy_service() to only set the
manual configuration bits once after we have figured them all out. For
ip1000phy_service() this also means we no longer unnecessarily update
the hardware along the road.
MFC after: 1 week
the lock instead of queueing it to a task.
- Do not invoke jme_rxintr() to reclaim any unprocessed but received
packets when shutting down the interface. Instead, just drop these
packets to match the behavior of other drivers.
- Hold the driver lock in the interrupt handler to avoid races with
ioctl requests to down the interface.
Reviewed by: yongari
limit maximum RX buffer size to RE_RX_DESC_BUFLEN instead of
blindly configuring it to 16KB. Due to lack of documentation, re(4)
didn't allow jumbo frame on these controllers. However it seems
controller is confused with jumbo frame such that it can DMA the
received frame to wrong address instead of splitting it into
multiple RX buffers. Of course, this caused panic.
Since re(4) does not support jumbo frames on these controllers,
make controller drop frame that is longer than RE_RX_DESC_BUFLEN
sized frame. Fortunately RTL810x controllers, which do not support
jumbo frame, have no such issues but this change also limited
maximum RX buffer size allowed to RTL810x controllers. Allowing
16KB RX buffer for controllers that have no such capability is
meaningless.
MFC after: 3 days
- failure code in em_xmit got mangled along the way
and was not properly handling errors.
- local timer code had a leftover UNLOCK call that
should be removed.
MFC after 3 days
and just show old (cached) values. Controller will not respond to
the command unless MAC is enabled so DUMP request for down
interface caused request timeout.
RealTek changed TX descriptor format for later controllers so these
controllers require MSS configuration in different location of TX
descriptor. TSO is enabled by default for controllers that use new
descriptor format.
For old controllers, TSO is still disabled by default due to broken
frames under certain conditions but users can enable it.
Special thanks to Hayes Wang at RealTek.
MFC after: 2 weeks
