pmap_sync_icache() to sync random (possibly uncached or nonexisting!)
memory, causing kernel page faults or machine checks, most easily
triggered by using GDB. While here, add an additional safeguard to only
sync cacheable memory.
MFC after: 2 days
Renovate and improve the AIM Open Firmware support:
- Add RTAS (Run-Time Abstraction Services) support, found on all IBM systems
and some Apple ones
- Improve support for 32-bit real mode Open Firmware systems
- Pull some more OF bits over from the AIM directory
- Fix memory detection on IBM LPARs and systems with more than one /memory
node (by andreast@)
be brought up in the order they are enumerated in the device tree (in
particular, that thread 0 on each core be brought up first). The SLIST
through which we loop to start the CPUs has all of its entries added with
SLIST_INSERT_HEAD(), which means it is in reverse order of enumeration
and so AP startup would always fail in such situations (causing a machine
check or RTAS failure). Fix this by changing the SLIST into an STAILQ,
and inserting new CPUs at the end.
Reviewed by: jhb
Kelvin temperature, which is impossible except for some contrived magnetic
spin systems), use the previous measurement from that sensor instead of
corrupting everything and randomly changing the fans or shutting off the
machine.
o In bare_probe(), change the logic that determines the maximum
number of processors/cores into a switch statement and take
advantage of the fact that bit 3 of the SVR value indicates
whether we're running on a security enabled version. Since we
don't care about that here, mask the bit. All -E versions
are taken care of automatically.
that will connect all of the various sensors and fan control modules on
Apple hardware with software-controlled fans (e.g. all G5 systems).
MFC after: 1 month
MPC8555(E) has 8 LAWs, so don't make that the default case. Current
processors have 12 LAWs so use that as the default instead.
o Determine the target ID of the PCI/PCI-X and PCI-E controllers in
a way that's more future proof. There's almost a perfect mapping
from HC register offset to target ID, so use that as the default.
Handle the MPC8548(E) specially, since it has a non-standard target
ID for the PCI-E controller. Don't worry about whether the processor
implements the target ID here, because we should not get called for
PCI/PCI-X or PCI-E host controllers that don't exist.
from U-Boot, the kernel is passed a standard argc/argv pair.
The Juniper loader passes the metadata pointer as the second
argument and passes 0 in the first. The FreeBSD loader passes
the metadata pointer in the first argument.
As such, have locore preserve the first 2 arguments in registers
r30 & r31. Change e500_init() to accept these arguments. Don't
pass global offsets (i.e. kernel_text and _end) as arguments to
e500_init(). We can reference those directly.
Rename e500_init() to booke_init() now that we're changing the
prototype.
In booke_init(), "decode" arg1 and arg2 to obtain the metadata
pointer correctly. For the U-Boot case, clear SBSS and BSS and
bank on having a static FDT for now. This allows loading the
ELF kernel and jumping to the entry point without trampoline.
a tendency to grow unwieldy so we may want to revisit this in due
time.
o Simplify the CPU reset function by writing to the reset control
register irrespective of whether the CPU has one and automatically
falling back to the debug control register if we didn't reset the
CPU. The side-effect is that we now properly reset future processors
without first having to add the system version to the list.
U-Boot as found on the P1020RDB doesn't like it when we use entry 1
(for some reason) whereas an older U-Boot doesn't mind if we use entry
0. If anything else, this simplifies the code a bit.
Rewrite atomic operations for powerpc in order to achieve the following:
- Produce a type-clean implementation (in terms of functions arguments
and returned values) for the primitives.
- Fix errors with _long() atomics where they ended up with the wrong
arguments to be accepted.
- Follow the sys/type.h specifics that define the numbered types starting
from standard C types.
- Let _ptr() version to not auto-magically cast arguments, but leave
the burden on callers, as _ptr() atomic is intended to be used
relatively rarely.
Fix cfi in order to support the latest point.
In collabouration with: bde
Tested by: andreast, nwhitehorn, jceel
MFC after: 2 weeks
architectures (i386, for example) the virtual memory space may be
constrained enough that 2MB is a large chunk. Use 64K for arches
other than amd64 and ia64, with special handling for sparc64 due to
differing hardware.
Also commit the comment changes to kmem_init_zero_region() that I
missed due to not saving the file. (Darn the unfamiliar development
environment).
Arch maintainers, please feel free to adjust ZERO_REGION_SIZE as you
see fit.
Requested by: alc
MFC after: 1 week
MFC with: r221853
CPU. This fixes a panic observed on Heathrow-based systems without
SMP-capable PICs when the kernel had both options SMP and INVARIANTS.
MFC after: 5 days
starting from base C types (int, long, etc).
That is also reflected when building atomic operations, as the
size-bounded types are built from the base C types.
However, powerpc does the inverse thing, leading to a serie of nasty
bugs.
Cleanup the atomic implementation by defining as base the base C type
version and depending on them, appropriately.
Tested by: jceel
versions instead. They were never needed as bus_generic_intr() and
bus_teardown_intr() had been changed to pass the original child device up
in 42734, but the ISA bus was not converted to new-bus until 45720.
disk dumping.
With the option SW_WATCHDOG on, these operations are doomed to let
watchdog fire, fi they take too long.
I implemented the stubs this way because I really want wdog_kern_*
KPI to not be dependant by SW_WATCHDOG being on (and really, the option
only enables watchdog activation in hardclock) and also avoid to
call them when not necessary (avoiding not-volountary watchdog
activations).
Sponsored by: Sandvine Incorporated
Discussed with: emaste, des
MFC after: 2 weeks
NFS client (which I guess is no longer experimental). The fstype "newnfs"
is now "nfs" and the regular/old NFS client is now fstype "oldnfs".
Although mounts via fstype "nfs" will usually work without userland
changes, an updated mount_nfs(8) binary is needed for kernels built with
"options NFSCL" but not "options NFSCLIENT". Updated mount_nfs(8) and
mount(8) binaries are needed to do mounts for fstype "oldnfs".
The GENERIC kernel configs have been changed to use options
NFSCL and NFSD (the new client and server) instead of NFSCLIENT and NFSSERVER.
For kernels being used on diskless NFS root systems, "options NFSCL"
must be in the kernel config.
Discussed on freebsd-fs@.
stack. It means that all legacy ATA drivers are disabled and replaced by
respective CAM drivers. If you are using ATA device names in /etc/fstab or
other places, make sure to update them respectively (adX -> adaY,
acdX -> cdY, afdX -> daY, astX -> saY, where 'Y's are the sequential
numbers for each type in order of detection, unless configured otherwise
with tunables, see cam(4)).
ataraid(4) functionality is now supported by the RAID GEOM class.
To use it you can load geom_raid kernel module and use graid(8) tool
for management. Instead of /dev/arX device names, use /dev/raid/rX.
explicit process at fork trampoline path instead of eventhadler(schedtail)
invocation for each child process.
Remove eventhandler(schedtail) code and change linux ABI to use newly added
sysvec method.
While here replace explicit comparing of module sysentvec structure with the
newly created process sysentvec to detect the linux ABI.
Discussed with: kib
MFC after: 2 Week
should_yield(). Use this in various places. Encapsulate the common
case of check-and-yield into a new function maybe_yield().
Change several checks for a magic number of iterations to use
should_yield() instead.
MFC after: 1 week
already supported nested PICs, but was limited to having a nested
AT-PIC only. With G5 support the need for nested OpenPIC controllers
needed to be added. This was done the wrong way and broke the MPC8555
eval system in the process.
OFW, as well as FDT, describe the interrupt routing in terms of a
controller and an interrupt pin on it. This needs to be mapped to a
flat and global resource: the IRQ. The IRQ is the same as the PCI
intline and as such needs to be representable in 8 bits. Secondly,
ISA support pretty much dictates that IRQ 0-15 should be reserved
for ISA interrupts, because of the internal workins of south bridges.
Both were broken.
This change reverts revision 209298 for a big part and re-implements
it simpler. In particular:
o The id() method of the PIC I/F is removed again. It's not needed.
o The openpic_attach() function has been changed to take the OFW
or FDT phandle of the controller as a second argument. All bus
attachments that previously used openpic_attach() as the attach
method of the device I/F now implement as bus-specific method
and pass the phandle_t to the renamed openpic_attach().
o Change powerpc_register_pic() to take a few more arguments. In
particular:
- Pass the number of IPIs specificly. The number of IRQs carved
out for a PIC is the sum of the number of int. pins and IPIs.
- Pass a flag indicating whether the PIC is an AT-PIC or not.
This tells the interrupt framework whether to assign IRQ 0-15
or some other range.
o Until we implement proper multi-pass bus enumeration, we have to
handle the case where we need to map from PIC+pin to IRQ *before*
the PIC gets registered. This is done in a similar way as before,
but rather than carving out 256 IRQs per PIC, we carve out 128
IRQs (124 pins + 4 IPIs). This is supposed to handle the G5 case,
but should really be fixed properly using multiple passes.
o Have the interrupt framework set root_pic in most cases and not
put that burden in PIC drivers (for the most part).
o Remove powerpc_ign_lookup() and replace it with powerpc_get_irq().
Remove IGN_SHIFT, INTR_INTLINE and INTR_IGN.
Related to the above, fix the Freescale PCI controller driver, broken
by the FDT code. Besides not attaching properly, bus numbers were
assigned improperly and enumeration was broken in general. This
prevented the AT PIC from being discovered and interrupt routing to
work properly. Consequently, the ata(4) controller stopped functioning.
Fix the driver, and FDT PCI support, enough to get the MPC8555CDS
going again. The FDT PCI code needs a whole lot more work.
No breakages are expected, but lackiong G5 hardware, it's possible
that there are unpleasant side-effects. At least MPC85xx support is
back to where it was 7 months ago -- it's amazing how badly support
can be broken in just 7 months...
Sponsored by: Juniper Networks
is on the MacIO ones. It appears to be unreliable on all DBDMA-based
controllers for unknown reasons, which should be figured out eventually.
Tested by: Torfinn Ingolfsen
MFC after: 1 week
sf buf allocation, use wakeup() instead of wakeup_one() to notify sf
buffer waiters about free buffer.
sf_buf_alloc() calls msleep(PCATCH) when SFB_CATCH flag was given,
and for simultaneous wakeup and signal delivery, msleep() returns
EINTR/ERESTART despite the thread was selected for wakeup_one(). As
result, we loose a wakeup, and some other waiter will not be woken up.
Reported and tested by: az
Reviewed by: alc, jhb
MFC after: 1 week
1. Allow embedding the FDT into the kernel, just like PowerPC/book-E.
2. If the loader passes us a pointer to the bootinfo structure, save
it and use it to fill in the gaps (e.g. bus frequencies, etc).
Compile sys/dev/mem/memutil.c for all supported platforms and remove now
unnecessary dev_mem_md_init(). Consistently define mem_range_softc from
mem.c for all platforms. Add missing #include guards for machine/memdev.h
and sys/memrange.h. Clean up some nearby style(9) nits.
MFC after: 1 month
the pwm values. We can now set the fan's speed of a PWM controlled fan
with % numbers between 30 and 100 % instead of trying to model a
% number based on rpm.
The fcu chip offers both, the dutycycle and the rpm value of the PWM
controlled fans. I added the rpm value to the list of information
available via sysctl(8).
Tested by: Paul Mather <paul at gromit dlib vt edu>
Approved by: nwhitehorn (mentor)
and pointers don't always have the same size, e.g. the __mips_n32 ABI
(ILP32) has 64 bit registers but 32 bit pointers.
On mips introduce PRIptr to fix the format specifier for (u)intptr_t.
Prefix PRI64 and PRIptr with underscores because macro names starting with
PRI[a-zX] are reserved for future use.
Approved by: kib (mentor)
architecture macros (__mips_n64, __powerpc64__) when 64 bit types (and
corresponding macros) are different from 32 bit. [1]
Correct the type of INT64_MIN, INT64_MAX and UINT64_MAX.
Define (U)INTMAX_C as an alias for (U)INT64_C matching the type definition
for (u)intmax_t. Do this on all architectures for consistency.
Suggested by: bde [1]
Approved by: kib (mentor)
of (unsigned) int __attribute__((__mode__(__DI__))). This aligns better
with macros such as (U)INT64_C, (U)INT64_MAX, etc. which assume (u)int64_t
has type (unsigned) long long.
The mode attribute was used because long long wasn't standardised until
C99. Nowadays compilers should support long long and use of the mode
attribute is discouraged according to GCC Internals documentation.
The type definition has to be marked with __extension__ to support
compilation with "-std=c89 -pedantic".
Discussed with: bde
Approved by: kib (mentor)
On some architectures UCHAR_MAX and USHRT_MAX had type unsigned int.
However, lacking integer suffixes for types smaller than int, their type
should correspond to that of an object of type unsigned char (or short)
when used in an expression with objects of type int. In that case unsigned
char (short) are promoted to int (i.e. signed) so the type of UCHAR_MAX and
USHRT_MAX should also be int.
Where MIN/MAX constants implicitly have the correct type the suffix has
been removed.
While here, correct some comments.
Reviewed by: bde
Approved by: kib (mentor)
It was used mainly to discover and fix some 64-bit portability problems
before 64-bit arches were widely available.
Discussed with: bde
Approved by: kib (mentor)
available on firmwares 3.15 and earlier.
Caveats: Support for the internal SATA controller is currently missing,
as is support for framebuffer resolutions other than 720x480. These
deficiencies will be remedied soon.
Special thanks to Peter Grehan for providing the hardware that made this
port possible, and thanks to Geoff Levand of Sony Computer Entertainment
for advice on the LV1 hypervisor.
length to ofw_real_map in case of a null string.
This makes ofwdump(8) work correctly when trying to print all properties
with ofwdump -p.
Approved by: nwhitehorn (mentor)
table. The 'locked' attribute is used to circumvent the regular page table
locking for some special pages, with the result that including locked pages
here causes races when updating the stats.
logic to support modifying the page table through a hypervisor. This
uses KOBJ inheritance to provide subclasses of the base 64-bit AIM MMU
class with additional methods for page table manipulation.
Many thanks to Peter Grehan for suggesting this design and implementing
the MMU KOBJ inheritance mechanism.
Passing a count of zero on i386 and amd64 for [I386|AMD64]_BUS_SPACE_MEM
causes a crash/hang since the 'loop' instruction decrements the counter
before checking if it's zero.
PR: kern/80980
Discussed with: jhb
byte-swapped versions of compile-time constants. This allows use of
bswap() and htole*() in initializers, which is required to cross-build
btxld.
Obtained from: sparc64
i.e. alignment, max_address, max_iosize and segsize (only max_address is
thought to have an negative impact regarding this issue though), after
calling ata_dmainit() either directly or indirectly so these values have
no effect or at least no effect on the DMA tags and the defaults are used
for the latter instead. So change the drivers to set these parameters
up-front and ata_dmainit() to honor them.
This file was missed in r216013.
Submitted by: nwhitehorn
DPCPU_DEFINE and VNET_DEFINE macros, as these cause problems for various
people working on the affected files. A better long-term solution is
still being considered. This reversal may give some modules empty
set_pcpu or set_vnet sections, but these are harmless.
Changes reverted:
------------------------------------------------------------------------
r215318 | dim | 2010-11-14 21:40:55 +0100 (Sun, 14 Nov 2010) | 4 lines
Instead of unconditionally emitting .globl's for the __start_set_xxx and
__stop_set_xxx symbols, only emit them when the set_vnet or set_pcpu
sections are actually defined.
------------------------------------------------------------------------
r215317 | dim | 2010-11-14 21:38:11 +0100 (Sun, 14 Nov 2010) | 3 lines
Apply the STATIC_VNET_DEFINE and STATIC_DPCPU_DEFINE macros throughout
the tree.
------------------------------------------------------------------------
r215316 | dim | 2010-11-14 21:23:02 +0100 (Sun, 14 Nov 2010) | 2 lines
Add macros to define static instances of VNET_DEFINE and DPCPU_DEFINE.
that causes AP bringup to fail if some of the Cell HID-register code
is anywhere in the instruction stream. Pending a better solution, cache
performance on SMP Cell systems running without a hypervisor will be
suboptimal.
mappings need to end up in the kernel anyway since the kernel begins
executing in OF context. Separating them adds needless complexity,
especially since the powerpc64 and mmu_oea64 code gave up on it a long
time ago.
As a side effect, the PPC ofw_machdep code is no longer AIM-specific,
so move it to powerpc/ofw.
hypervisor infrastructure support:
- Fix coexistence of multiple platform modules in the same kernel
- Allow platform modules to provide an SMP topology
- PowerPC hypervisors limit the amount of memory accessible in real mode.
Allow the platform modules to specify the maximum real-mode address,
and modify the bits of the kernel that need to allocate
real-mode-accessible buffers to respect this limits.
routines.
This unbreaks Book-E build after the recent machine/mutex.h removal.
While there move tlb_*lock() prototypes to machine/tlb.h.
Submitted by: jhb
MSR[DEEPNAP] be set, not just MSR[DEEPNAP]. Fixing this reduces the idle
temperature of my CPUs from 57 to 38 degrees and makes one-shot timer
mode work properly.
Hint from: mav
MFC after: 4 days
contents of the ones that were not empty were stale and unused.
- Now that <machine/mutex.h> no longer exists, there is no need to allow it
to override various helper macros in <sys/mutex.h>.
- Rename various helper macros for low-level operations on mutexes to live
in the _mtx_* or __mtx_* namespaces. While here, change the names to more
closely match the real API functions they are backing.
- Drop support for including <sys/mutex.h> in assembly source files.
Suggested by: bde (1, 2)
work properly with single-stepping in a kernel debugger. Specifically,
these routines have always disabled interrupts before increasing the nesting
count and restored the prior state of interrupts after decreasing the nesting
count to avoid problems with a nested interrupt not disabling interrupts
when acquiring a spin lock. However, trap interrupts for single-stepping
can still occur even when interrupts are disabled. Now the saved state of
interrupts is not saved in the thread until after interrupts have been
disabled and the nesting count has been increased. Similarly, the saved
state from the thread cannot be read once the nesting count has been
decreased to zero. To fix this, use temporary variables to store interrupt
state and shuffle it between the thread's MD area and the appropriate
registers.
In cooperation with: bde
MFC after: 1 month
only, and should be protected with an ifdef, and the no-execute bit in
32-bit set_user_sr() should be set before the comparison, not after, or
it will never match.
set_user_sr() itself caches the user segment VSID, there is no need for
cpu_switch() to do it again. This change also unifies the 32 and 64-bit
code paths for kernel faults on user pages and remaps the user SLB slot
on 64-bit systems when taking a syscall to avoid some unnecessary segment
exception traps.
concurrency bug. Since all SLB/SR entries were invalidated during an
exception, a decrementer exception could cause the user segment to be
invalidated during a copyin()/copyout() without a thread switch that
would cause it to be restored from the PCB, potentially causing the
operation to continue on invalid memory. This is now handled by explicit
restoration of segment 12 from the PCB on 32-bit systems and a check in
the Data Segment Exception handler on 64-bit.
While here, cause copyin()/copyout() to check whether the requested
user segment is already installed, saving some pipeline flushes, and
fix the synchronization primitives around the mtsr and slbmte
instructions to prevent accessing stale segments.
MFC after: 2 weeks
PowerMac7,2.
- The fcu driver lets us read and write the fan RPMs for all fans in the
PowerMac7,2. This driver is PowerMac specific.
- The ds1775 is a driver to read the temperature for the drive bay sensor.
- The max6690 is another driver to read temperatures. Here it is used to
read the inlet, the backside and the U3 heatsink temperature.
An additional driver, the ad7417, will follow later.
Thanks to nwhitehorn for guiding me through this driver development.
Approved by: nwhitehorn (mentor)
values to zero. A correct solution would involve emulating vector
operations on denormalized values, but this has little effect on accuracy
and is much less complicated for now.
MFC after: 2 weeks
Unlike actual MTRR, this only controls the mapping attributes for
subsequent mmap() of /dev/mem. Nonetheless, the support is sufficiently
MTRR-like that Xorg can use it, which translates into an enormous increase
in graphics performance on PowerPC.
MFC after: 2 weeks
and set memory attributes appropriately for mmap() calls on /dev/console.
Xorg no longer uses /dev/console to mmap the framebuffer, so framebuffer
write combining support in X will arrive in the next patch.
by just caching the mode for later use by pmap_enter(), following amd64.
While here, correct some mismerges from mmu_oea64 -> mmu_oea and clean
up some dead code found while fixing the fictitious page behavior.
The check for alignment should be made against the physical address and not
the virtual address that maps it.
Sponsored by: NetApp
Submitted by: Will McGovern (will at netapp dot com)
Reviewed by: mjacob, jhb
which are similar to the previous ones, and one for user maps, which
are arrays of pointers into the SLB tree. This changes makes user SLB
updates atomic, closing a window for memory corruption. While here,
rearrange the allocation functions to make context switches faster.
hardware with a lockless sparse tree design. This marginally improves
the performance of PMAP and allows copyin()/copyout() to run without
acquiring locks when used on wired mappings.
Submitted by: mdf
include/mmuvar.h - Change the MMU_DEF macro to also create the class
definition as well as define the DATA_SET. Add a macro, MMU_DEF_INHERIT,
which has an extra parameter specifying the MMU class to inherit methods
from. Update the comments at the start of the header file to describe the
new macros.
booke/pmap.c
aim/mmu_oea.c
aim/mmu_oea64.c - Collapse mmu_def_t declaration into updated MMU_DEF macro
The MMU_DEF_INHERIT macro will be used in the PS3 MMU implementation to
allow it to inherit the stock powerpc64 MMU methods.
Reviewed by: nwhitehorn
any spin locks acquired between the enabling of interrupts in
machdep_ap_bootstrap() and the invocation of the scheduler would fail to
have interrupts disabled due to the fake spinlock already held by the
idle thread. sched_throw(NULL) will enable interrupts by itself when
exiting this spinlock, so just let it do that and don't enable interrupts
here.
The main goal of this is to generate timer interrupts only when there is
some work to do. When CPU is busy interrupts are generating at full rate
of hz + stathz to fullfill scheduler and timekeeping requirements. But
when CPU is idle, only minimum set of interrupts (down to 8 interrupts per
second per CPU now), needed to handle scheduled callouts is executed.
This allows significantly increase idle CPU sleep time, increasing effect
of static power-saving technologies. Also it should reduce host CPU load
on virtualized systems, when guest system is idle.
There is set of tunables, also available as writable sysctls, allowing to
control wanted event timer subsystem behavior:
kern.eventtimer.timer - allows to choose event timer hardware to use.
On x86 there is up to 4 different kinds of timers. Depending on whether
chosen timer is per-CPU, behavior of other options slightly differs.
kern.eventtimer.periodic - allows to choose periodic and one-shot
operation mode. In periodic mode, current timer hardware taken as the only
source of time for time events. This mode is quite alike to previous kernel
behavior. One-shot mode instead uses currently selected time counter
hardware to schedule all needed events one by one and program timer to
generate interrupt exactly in specified time. Default value depends of
chosen timer capabilities, but one-shot mode is preferred, until other is
forced by user or hardware.
kern.eventtimer.singlemul - in periodic mode specifies how much times
higher timer frequency should be, to not strictly alias hardclock() and
statclock() events. Default values are 2 and 4, but could be reduced to 1
if extra interrupts are unwanted.
kern.eventtimer.idletick - makes each CPU to receive every timer interrupt
independently of whether they busy or not. By default this options is
disabled. If chosen timer is per-CPU and runs in periodic mode, this option
has no effect - all interrupts are generating.
As soon as this patch modifies cpu_idle() on some platforms, I have also
refactored one on x86. Now it makes use of MONITOR/MWAIT instrunctions
(if supported) under high sleep/wakeup rate, as fast alternative to other
methods. It allows SMP scheduler to wake up sleeping CPUs much faster
without using IPI, significantly increasing performance on some highly
task-switching loads.
Tested by: many (on i386, amd64, sparc64 and powerc)
H/W donated by: Gheorghe Ardelean
Sponsored by: iXsystems, Inc.
This reflects actual type used to store and compare child device orders.
Change is mostly done via a Coccinelle (soon to be devel/coccinelle)
semantic patch.
Verified by LINT+modules kernel builds.
Followup to: r212213
MFC after: 10 days
wrong element of the VSID bitmap array to be examined after a collision,
leading to reallocation of in-use VSIDs under some circumstances, with
attendant memory corruption. Also add an assert to check for this kind of
problem in the future.
MFC after: 4 days
PowerPC CPUs running a 32-bit kernel. This bug could cause in-use VSIDs
to be allocated again to another process, causing memory space overlaps
and corruption.
Reported by: linimon
A make buildkernel -j4 uses ~360% CPU.
- Bracket the AP spinup printf with a mutex to avoid garbled output.
- Enable SMP by default on powerpc64.
Reviewed by: nwhitehorn
the existing code was very platform specific, and broken for SMP systems
trying to reboot from KDB.
- Add a new PLATFORM_RESET() method to the platform KOBJ interface, and
migrate existing reset functions into platform modules.
- Modify the OF_reboot() routine to submit the request by hand to avoid
the IPIs involved in the regular openfirmware() routine. This fixes
reboot from KDB on SMP machines.
- Move non-KDB reset and poweroff functions on the Powermac platform
into the relevant power control drivers (cuda, pmu, smu), instead of
using them through the Open Firmware backdoor.
- Rename platform_chrp to platform_powermac since it has become
increasingly Powermac specific. When we gain support for IBM systems,
we will grow a new platform_chrp.
In particular, provide pagesize and pagesizes array, the canary value
for SSP use, number of host CPUs and osreldate.
Tested by: marius (sparc64)
MFC after: 1 month
IPI to a specific CPU by its cpuid. Replace calls to ipi_selected() that
constructed a mask for a single CPU with calls to ipi_cpu() instead. This
will matter more in the future when we transition from cpumask_t to
cpuset_t for CPU masks in which case building a CPU mask is more expensive.
Submitted by: peter, sbruno
Reviewed by: rookie
Obtained from: Yahoo! (x86)
MFC after: 1 month
zones for each malloc bucket size. The purpose is to isolate
different malloc types into hash classes, so that any buffer overruns
or use-after-free will usually only affect memory from malloc types in
that hash class. This is purely a debugging tool; by varying the hash
function and tracking which hash class was corrupted, the intersection
of the hash classes from each instance will point to a single malloc
type that is being misused. At this point inspection or memguard(9)
can be used to catch the offending code.
Add MALLOC_DEBUG_MAXZONES=8 to -current GENERIC configuration files.
The suggestion to have this on by default came from Kostik Belousov on
-arch.
This code is based on work by Ron Steinke at Isilon Systems.
Reviewed by: -arch (mostly silence)
Reviewed by: zml
Approved by: zml (mentor)
now it uses a very dumb first-touch allocation policy. This will change in
the future.
- Each architecture indicates the maximum number of supported memory domains
via a new VM_NDOMAIN parameter in <machine/vmparam.h>.
- Each cpu now has a PCPU_GET(domain) member to indicate the memory domain
a CPU belongs to. Domain values are dense and numbered from 0.
- When a platform supports multiple domains, the default freelist
(VM_FREELIST_DEFAULT) is split up into N freelists, one for each domain.
The MD code is required to populate an array of mem_affinity structures.
Each entry in the array defines a range of memory (start and end) and a
domain for the range. Multiple entries may be present for a single
domain. The list is terminated by an entry where all fields are zero.
This array of structures is used to split up phys_avail[] regions that
fall in VM_FREELIST_DEFAULT into per-domain freelists.
- Each memory domain has a separate lookup-array of freelists that is
used when fulfulling a physical memory allocation. Right now the
per-domain freelists are listed in a round-robin order for each domain.
In the future a table such as the ACPI SLIT table may be used to order
the per-domain lookup lists based on the penalty for each memory domain
relative to a specific domain. The lookup lists may be examined via a
new vm.phys.lookup_lists sysctl.
- The first-touch policy is implemented by using PCPU_GET(domain) to
pick a lookup list when allocating memory.
Reviewed by: alc
