new devmap.[ch] files. Emphasize the MD nature of these things by using
the prefix arm_devmap_ on the function and type names (already a few of
these things found their way into MI code, hopefully it will be harder to
do by accident in the future).
Loading kernel to 0xf00000 has no practical reason.
Starting it from the u-boot's highest possible end address
(2MB counting from 0x0) makes more sense.
Tested by: kevlo
Depending on u-boot's flavor some boards have their SoC registers
base address configured to 0xD0000000 and other to 0xF1000000.
U-boot is passing currently set value via CP15 register.
In order to create proper mapping for SoC registers and allow further
successful initialization it is necessary to replace fdt_immr_pa with
the real value and eventually fix-up device tree blob.
Tested by: kevlo
The only remaining user was the code that allocates bounce pages for armv4
busdma. It's not clear why bounce pages would need uncached memory, but
if that ever changes, kmem_alloc_attr() would be the way to get it.
really need it. That would be almost everywhere it was included. Add
it in a couple files that really do need it and were previously getting
it by accident via another header.
included by vm/pmap.h, which is a prerequisite for arm/machine/pmap.h
so there's no reason to ever include it directly.
Thanks to alc@ for pointing this out.
the right register for power managment. It
was incorrectly using the clock register
which also caused the status to be the
opposite of what it is supposed to be.
1 - its disabled
0 - its enabled
Per kirkwood spec FSS_88F6180_9x_6281_OpenSource.pdf
transparent layering and better fragmentation.
- Normalize functions that allocate memory to use kmem_*
- Those that allocate address space are named kva_*
- Those that operate on maps are named kmap_*
- Implement recursive allocation handling for kmem_arena in vmem.
Reviewed by: alc
Tested by: pho
Sponsored by: EMC / Isilon Storage Division
In order to become independent of Coherency Fabric frequency, configure
Timer and Watchdog to operate in 25MHz mode.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
- On ARMADAXP B0 (GP development board) we are not able to use PCI due to
whole 32-bit address space used by 4GB of RAM memory.
- Change is required to destroy unnecessary window to free address space
for PCI and other devices
- Fix offset value for SDRAM decoding windows
Obtained from: Semihalf
to driver specific files.
- window initialization is done during device attach
- CESA TDMA decoding windows values are set based on DTS,
not copied from CPU registers
- remove unnecessary virtual mapping
- update dts file
Obtained from: Semihalf
Switch eventtimers(9) from using struct bintime to sbintime_t.
Even before this not a single driver really supported full dynamic range of
struct bintime even in theory, not speaking about practical inexpediency.
This change legitimates the status quo and cleans up the code.
so that we don't need an empty implementation of it for every Marvell platform
that has no PCI. This allows the removal of the SheevaPlug-specific stub and
config files, and eliminates the need to add similar stubs for future models.
Marvell platforms that do expose PCI are compiled with 'device pci' which
causes the real (non-weak) implementation in dev/fdt/fdt_pci.c to be used.
Approved by: cognet (mentor)
The copies of initarm used on platforms with FDT support were almost
identical. The differences were pulled out into separate functions that
were called by initarm.
This change merges the, now identical, copies of initarm and a few of it's
support functions. This is a step towards a common kernel on ARMv6.
On single core devices set_stackptrs is only ever called with cpu = 0 in
initarm and will be identical to the existing function. On SMP this needs
to be implemented for sys/arm/mp_machdep.c, but the implementations are
identical for each SoC.
MSI are implemented via Inbound Shared Doorbell 1 interrupts. Interrupts
are triggered by writing to Software Triggered Interrupt registeri (PCIe
card using physical address of this register in BAR0 space). There are 32
interrupts available. It can be increased by using Doorbell 2 and
Doorbell 3 registers to 96 interrupts.
Obtained from: Marvell, Semihalf
MSI are implemented via software interrupt. PCIe cards will write
into software interrupt register which will cause inbound shared
interrupt which will be interpreted as a MSI.
Obtained from: Marvell, Semihalf
- Add functions to calculate clocks instead using hardcoded values
- Update reset and timers functions
- Update number of interrupts
- Change name of platform from db88f78100 to db78460
- Correct DRAM size and PCI IRQ routing in dts file.
Obtained from: Semihalf
frequencies. The maximum freqency is 100 kHz according to the datasheet.
- Add child device probing support based on the device tree. It now tries to
find i2c-address property in the tree and attach the device with given slave
address to iicbus.
this array either from Linux boot data, when enabled, or in the
typical way that most ports do it. arm_pyhs_avail_init is coming
soon since it must be a separate function.
is enabled, sets values based on the metadata passed in. Otherwise
fake_preload_metadata is called. Change the default parse_boot_param
to default_parse_boot_param. Enable this functionality only on the mv
platform, which is where most of the code is from.
Reviewed by: cognet, Ian Lapore
the boot parameters from initarm first thing. parse_boot_param parses
the boot arguments and converts them to the /boot/loader metadata the
rest of the kernel uses. parse_boot_param is a weak alias to
fake_preload_metadata, which all the platforms use now, but may become
more extensive in the future.
Since it is a weak symbol, specific boards may define their own
parse_boot_param to interface to custom boot loaders.
Reviewed by: cognet@, Ian Lapore
structure with the first 4 registers to allow a wider range of boot
loaders to work. Future commits will make use of this to centralize
support for the different loaders.
