o) Add 'octm', a trivial driver for the 10/100 management ports found on some
Octeon systems.
o) Make the Simple Executive's management port helper routines compile on
FreeBSD (namely by not doing math on void pointers.)
o) Add a cvmx_mgmt_port_sendm routine to the Simple Executive to send an mbuf
so there is only one copy in the transmit path, rather than having to first
copy the mbuf to an intermediate buffer and then copy that to the Simple
Executive's transmit ring.
o) Properly work out MII addresses of management ports on the Lanner MR-730.
XXX The MR-730 also needs some patches to the MII read/write routines, but
this is sufficient for now. Media detection will be fixed in the future
when I can spend more time reading the vendor-supplied patches.
facilities as well as support for the Octeon 2 family of SoCs.
XXX Note that with our antediluvian assembler, we can't support some Octeon 2
instructions and fall back to using the old ones instead.
o) Fix enumeration of PHY addresses on the MR-955.
o) Parse link state for the MR-730 using the Broadcom PHY support in the SDK.
It's not clear that this is entirely-correct, but it seems to work. Since
this board uses a BCM5482S, this may mean that we work correctly for copper
but not SFI, which is untested.
the miibus attached to octe interfaces.
o) Add an SMI/MDIO interface to the MV88E61XX and use it for the switch PHY on
the Lanner MR-320. An actual driver for the switch PHY will come later.
Note that for now it intercepts and fakes MII_BMSR reads to prevent the
miibus from talking to anything but the switch itself.
seem to be problems both with the on-board Ethernet interfaces and the em(4)
interfaces on PCI under FreeBSD.
Thanks to Lanner for providing access to hardware.
for interfaces with TSO enabled, otherwise one would see an extra
ICMP unreach, frag needed pre matching packet on lo0.
This syncs pf code to ip_output.c r162084.
PR: kern/144311
Submitted by: yongari via mlaier
Reviewed by: eri
Tested by: kib
MFC after: 8 days
library:
o) Increase inline unit / large function growth limits for MIPS to accommodate
the needs of the Simple Executive, which uses a shocking amount of inlining.
o) Remove TARGET_OCTEON and use CPU_CNMIPS to do things required by cnMIPS and
the Octeon SoC.
o) Add OCTEON_VENDOR_LANNER to use Lanner's allocation of vendor-specific
board numbers, specifically to support the MR320.
o) Add OCTEON_BOARD_CAPK_0100ND to hard-wire configuration for the CAPK-0100nd,
which improperly uses an evaluation board's board number and breaks board
detection at runtime. This board is sold by Portwell as the CAM-0100.
o) Add support for the RTC available on some Octeon boards.
o) Add support for the Octeon PCI bus. Note that rman_[sg]et_virtual for IO
ports can not work unless building for n64.
o) Clean up the CompactFlash driver to use Simple Executive macros and
structures where possible (it would be advisable to use the Simple Executive
API to set the PIO mode, too, but that is not done presently.) Also use
structures from FreeBSD's ATA layer rather than structures copied from
Linux.
o) Print available Octeon SoC features on boot.
o) Add support for the Octeon timecounter.
o) Use the Simple Executive's routines rather than local copies for doing reads
and writes to 64-bit addresses and use its macros for various device
addresses rather than using local copies.
o) Rename octeon_board_real to octeon_is_simulation to reduce differences with
Cavium-provided code originally written for Linux. Also make it use the
same simplified test that the Simple Executive and Linux both use rather
than our complex one.
o) Add support for the Octeon CIU, which is the main interrupt unit, as a bus
to use normal interrupt allocation and setup routines.
o) Use the Simple Executive's bootmem facility to allocate physical memory for
the kernel, rather than assuming we know which addresses we can steal.
NB: This may reduce the amount of RAM the kernel reports you as having if
you are leaving large temporary allocations made by U-Boot allocated
when starting FreeBSD.
o) Add a port of the Cavium-provided Ethernet driver for Linux. This changes
Ethernet interface naming from rgmxN to octeN. The new driver has vast
improvements over the old one, both in performance and functionality, but
does still have some features which have not been ported entirely and there
may be unimplemented code that can be hit in everyday use. I will make
every effort to correct those as they are reported.
o) Support loading the kernel on non-contiguous cores.
o) Add very conservative support for harvesting randomness from the Octeon
random number device.
o) Turn SMP on by default.
o) Clean up the style of the Octeon kernel configurations a little and make
them compile with -march=octeon.
o) Add support for the Lanner MR320 and the CAPK-0100nd to the Simple
Executive.
o) Modify the Simple Executive to build on FreeBSD and to build without
executive-config.h or cvmx-config.h. In the future we may want to
revert part of these changes and supply executive-config.h and
cvmx-config.h and access to the options contained in those files via
kernel configuration files.
o) Modify the Simple Executive USB routines to support getting and setting
of the USB PID.
Executive is a library that can be used by standalone applications and kernels
to abstract access to Octeon SoC and board-specific hardware and facilities.
The FreeBSD port to Octeon will be updated to use this where possible.
"Whitspace" churn after the VIMAGE/VNET whirls.
Remove the need for some "init" functions within the network
stack, like pim6_init(), icmp_init() or significantly shorten
others like ip6_init() and nd6_init(), using static initialization
again where possible and formerly missed.
Move (most) variables back to the place they used to be before the
container structs and VIMAGE_GLOABLS (before r185088) and try to
reduce the diff to stable/7 and earlier as good as possible,
to help out-of-tree consumers to update from 6.x or 7.x to 8 or 9.
This also removes some header file pollution for putatively
static global variables.
Revert VIMAGE specific changes in ipfilter::ip_auth.c, that are
no longer needed.
Reviewed by: jhb
Discussed with: rwatson
Sponsored by: The FreeBSD Foundation
Sponsored by: CK Software GmbH
MFC after: 6 days
it from machine/in_cksum.h. This definition prevents us from using
hand-tuned assembler versions of in_cksum.
# this fixes the modules build on arm for ipfilter.
This is a split merge because of non-uniform licensing of the DTC package
contents and the way these components will be used in the FreeBSD environment.
The original DTC package is composed of the following two major pieces:
1. sys/contrib/libfdt (BSD [dual] license)
2. contrib/dtc (GPLv2)
The libfdt component is going to be shared in all aspects of the environment:
- /boot/loader
- kernel
- dtc (the device tree compiler proper, userspace tool)
TRENDnet TEW-504UB/EU) idProduct didn't be decreased after loading the
firmware.
Pointed by: Steven Friedrich <freebsd at insightbb.com>
Reviewed by: sam
* new firmware
* untested support for 1000 and 6000 series
* bgscan support
* remove unnecessary RXON changes
* allow setting of country/regdomain by enforcing channel flags read
from the EEPROM
* suspend/resume fixes
* RF kill switch fixes
* LED adjustments
* several bus_dma*() related fixes
* addressed some LORs
* many other bug fixes
Submitted by: Bernhard Schmidt <bschmidt at techwires.net>
Obtained from: Brandon Gooch <jamesbrandongooch at gmail dot com> (LED
related changes), Benjamin Kaduk <kaduk at mit dot edu>
(LOR fixes), OpenBSD
Server Return mode, where not all packets would be visible to the load
balancer or gateway.
This commit should be reverted when we merge future pf versions. The
benefit it would provide is that this version does not break any existing
public interface and thus won't be a problem if we want to MFC it to
earlier FreeBSD releases.
Discussed with: mlaier
Obtained from: OpenBSD
Sponsored by: iXsystems, Inc.
MFC after: 1 month
- Do not map entire real mode memory (1MB). Instead, we map IVT/BDA and
ROM area separately. Most notably, ROM area is mapped as device memory
(uncacheable) as it should be. User memory is dynamically allocated and
free'ed with contigmalloc(9) and contigfree(9). Remove now redundant and
potentially dangerous x86bios_alloc.c. If this emulator ever grows to
support non-PC hardware, we may implement it with rman(9) later.
- Move all host-specific initializations from x86emu_util.c to x86bios.c and
remove now unnecessary x86emu_util.c. Currently, non-PC hardware is not
supported. We may use bus_space(9) later when the KPI is fixed.
- Replace all bzero() calls for emulated registers with more obviously named
x86bios_init_regs(). This function also initializes DS and SS properly.
- Add x86bios_get_intr(). This function checks if the interrupt vector is
available for the platform. It is not necessary for PC-compatible hardware
but it may be needed later. ;-)
- Do not try turning off monitor if DPMS does not support the state.
- Allocate stable memory for VESA OEM strings instead of just holding
pointers to them. They may or may not be accessible always. Fix a memory
leak of video mode table while I am here.
- Add (experimental) BIOS POST call for vesa(4). This function calls VGA
BIOS POST code from the current VGA option ROM. Some video controllers
cannot save and restore the state properly even if it is claimed to be
supported. Usually the symptom is blank display after resuming from suspend
state. If the video mode does not match the previous mode after restoring,
we try BIOS POST and force the known good initial state. Some magic was
taken from NetBSD (and it was taken from vbetool, I believe.)
- Add a loader tunable for vgapci(4) to give a hint to dpms(4) and vesa(4)
to identify who owns the VESA BIOS. This is very useful for multi-display
adapter setup. By default, the POST video controller is automatically
probed and the tunable "hw.pci.default_vgapci_unit" is set to corresponding
vgapci unit number. You may override it from loader but it is very unlikely
to be necessary. Unfortunately only AGP/PCI/PCI-E controllers can be
matched because ISA controller does not have necessary device IDs.
- Fix a long standing bug in state save/restore function. The state buffer
pointer should be ES:BX, not ES:DI according to VBE 3.0. If it ever worked,
that's because BX was always zero. :-)
- Clean up register initializations more clearer per VBE 3.0.
- Fix a lot of style issues with vesa(4).
x86emu to this new module.
This changeset also brings a fix for bugs introduced with the initial
x86emu commit, which prevents the user from using some display mode or
cause instant reboots during mode switch.
Submitted by: paradox <ddkprog yahoo com>
several critical bugs, including race conditions and lock order issues:
Replace the single rwlock, ifnet_lock, with two locks, an rwlock and an
sxlock. Either can be held to stablize the lists and indexes, but both
are required to write. This allows the list to be held stable in both
network interrupt contexts and sleepable user threads across sleeping
memory allocations or device driver interactions. As before, writes to
the interface list must occur from sleepable contexts.
Reviewed by: bz, julian
MFC after: 3 days
restart the scan after acquiring the lock the hard way. Otherwise we might
end up with a dead reference.
Reported by: pfsense
Reviewed by: eri
Initial patch by: eri
Tested by: pfsense
Approved by: re (kib)
all pertinent statatistics for the subsystem. These structures are
sometimes "borrowed" by kernel modules that require a place to store
statistics for similar events.
Add KPI accessor functions for statistics structures referenced by kernel
modules so that they no longer encode certain specifics of how the data
structures are named and stored. This change is intended to make it
easier to move to per-CPU network stats following 8.0-RELEASE.
The following modules are affected by this change:
if_bridge
if_cxgb
if_gif
ip_mroute
ipdivert
pf
In practice, most of these statistics consumers should, in fact, maintain
their own statistics data structures rather than borrowing structures
from the base network stack. However, that change is too agressive for
this point in the release cycle.
Reviewed by: bz
Approved by: re (kib)
vnet.h, we now use jails (rather than vimages) as the abstraction
for virtualization management, and what remained was specific to
virtual network stacks. Minor cleanups are done in the process,
and comments updated to reflect these changes.
Reviewed by: bz
Approved by: re (vimage blanket)
(DPCPU), as suggested by Peter Wemm, and implement a new per-virtual
network stack memory allocator. Modify vnet to use the allocator
instead of monolithic global container structures (vinet, ...). This
change solves many binary compatibility problems associated with
VIMAGE, and restores ELF symbols for virtualized global variables.
Each virtualized global variable exists as a "reference copy", and also
once per virtual network stack. Virtualized global variables are
tagged at compile-time, placing the in a special linker set, which is
loaded into a contiguous region of kernel memory. Virtualized global
variables in the base kernel are linked as normal, but those in modules
are copied and relocated to a reserved portion of the kernel's vnet
region with the help of a the kernel linker.
Virtualized global variables exist in per-vnet memory set up when the
network stack instance is created, and are initialized statically from
the reference copy. Run-time access occurs via an accessor macro, which
converts from the current vnet and requested symbol to a per-vnet
address. When "options VIMAGE" is not compiled into the kernel, normal
global ELF symbols will be used instead and indirection is avoided.
This change restores static initialization for network stack global
variables, restores support for non-global symbols and types, eliminates
the need for many subsystem constructors, eliminates large per-subsystem
structures that caused many binary compatibility issues both for
monitoring applications (netstat) and kernel modules, removes the
per-function INIT_VNET_*() macros throughout the stack, eliminates the
need for vnet_symmap ksym(2) munging, and eliminates duplicate
definitions of virtualized globals under VIMAGE_GLOBALS.
Bump __FreeBSD_version and update UPDATING.
Portions submitted by: bz
Reviewed by: bz, zec
Discussed with: gnn, jamie, jeff, jhb, julian, sam
Suggested by: peter
Approved by: re (kensmith)
/boot/kernel/hptrr.ko
/etc/mail/*.cf
/lib/libcrypto.so.5
/usr/bin/ntpq
/usr/sbin/amd
/usr/sbin/iasl
/usr/sbin/ntpd
/usr/sbin/ntpdate
/usr/sbin/ntpdc
There does not appear to be any purpose to having these timestamps, and
they have the irritating consequence that the aforementioned files will
be different every time they are rebuilt.
After this commit, the only remaining build timestamps are in the kernel,
the boot loaders, /usr/include/osreldate.h (the year in the copyright
notice), and lib*.a (the timestamps on all of the included .o files).
Reviewed by: scottl (hptrr), gshapiro (sendmail), simon (openssl),
roberto (ntp), jkim (acpica)
Approved by: re (kib)
o new tx ack queue (not used right now)
o proxy-sta related changes (no proxy sta in driver)
o explicit dwds ena/dis (needed only with proxy sta)
o cleanup BA policy handling
o new ampdu aggressive mode support
o CFEnd use now controllable
Approved by: re (kensmith)
rather than pointers, requiring callers to properly dispose of those
references. The following routines now return references:
ifaddr_byindex
ifa_ifwithaddr
ifa_ifwithbroadaddr
ifa_ifwithdstaddr
ifa_ifwithnet
ifaof_ifpforaddr
ifa_ifwithroute
ifa_ifwithroute_fib
rt_getifa
rt_getifa_fib
IFP_TO_IA
ip_rtaddr
in6_ifawithifp
in6ifa_ifpforlinklocal
in6ifa_ifpwithaddr
in6_ifadd
carp_iamatch6
ip6_getdstifaddr
Remove unused macro which didn't have required referencing:
IFP_TO_IA6
This closes many small races in which changes to interface
or address lists while an ifaddr was in use could lead to use of freed
memory (etc). In a few cases, add missing if_addr_list locking
required to safely acquire references.
Because of a lack of deep copying support, we accept a race in which
an in6_ifaddr pointed to by mbuf tags and extracted with
ip6_getdstifaddr() doesn't hold a reference while in transmit. Once
we have mbuf tag deep copy support, this can be fixed.
Reviewed by: bz
Obtained from: Apple, Inc. (portions)
MFC after: 6 weeks (portions)
the ROUTETABLES kernel option thus there is no need to include opt_route.h
anymore in all consumers of vnet.h and no longer depend on it for module
builds.
Remove the hidden include in flowtable.h as well and leave the two
explicit #includes in ip_input.c and ip_output.c.
- Define ACPI_USE_DO_WHILE_0 to add do while(0) around return_*() macros.
- Define __cdecl only for user land. It will never be used in kernel.
- Remove __cli() and __sti(). They were deprecated long ago.
and used in a large number of files, but also because an increasing number
of incorrect uses of MAC calls were sneaking in due to copy-and-paste of
MAC-aware code without the associated opt_mac.h include.
Discussed with: pjd
by creating a child jail, which is visible to that jail and to any
parent jails. Child jails may be restricted more than their parents,
but never less. Jail names reflect this hierarchy, being MIB-style
dot-separated strings.
Every thread now points to a jail, the default being prison0, which
contains information about the physical system. Prison0's root
directory is the same as rootvnode; its hostname is the same as the
global hostname, and its securelevel replaces the global securelevel.
Note that the variable "securelevel" has actually gone away, which
should not cause any problems for code that properly uses
securelevel_gt() and securelevel_ge().
Some jail-related permissions that were kept in global variables and
set via sysctls are now per-jail settings. The sysctls still exist for
backward compatibility, used only by the now-deprecated jail(2) system
call.
Approved by: bz (mentor)
made LINT happy this does the proper looping over all vnets as we are
only called `globally' and not once per vnet instance.
Reported by: zec [1]
Missed by: bz [1] in r192264
Reviewed by: zec
rearrange / replace / adjust several INIT_VNET_* initializer
macros, all of which currently resolve to whitespace.
Reviewed by: bz (an older version of the patch)
Approved by: julian (mentor)
macros: ICMPSTAT_ADD(), ICMPSTAT_INC(), ICMP6STAT_ADD(), and
ICMP6STAT_INC(), rather than directly manipulating the fields
of these structures across the kernel. This will make it
easier to change the implementation of these statistics,
such as using per-CPU versions of the data structures.
In on case, icmp6stat members are manipulated indirectly, by
icmp6_errcount(), and this will require further work to fix
for per-CPU stats.
MFC after: 3 days
and UDPSTAT_INC(), rather than directly manipulating the fields
across the kernel. This will make it easier to change the
implementation of these statistics, such as using per-CPU versions
of the data structures.
MFC after: 3 days
IPSTAT_INC(), IPSTAT_SUB(), and IPSTAT_DEC(), rather than directly
manipulating the fields across the kernel. This will make it easier
to change the implementation of these statistics, such as using
per-CPU versions of the data structures.
MFC after: 3 days
TCPSTAT_INC(), rather than directly manipulating the fields across the
kernel. This will make it easier to change the implementation of
these statistics, such as using per-CPU versions of the data structures.
MFC after: 3 days
net/route.h.
Remove the hidden include of opt_route.h and net/route.h from net/vnet.h.
We need to make sure that both opt_route.h and net/route.h are included
before net/vnet.h because of the way MRT figures out the number of FIBs
from the kernel option. If we do not, we end up with the default number
of 1 when including net/vnet.h and array sizes are wrong.
This does not change the list of files which depend on opt_route.h
but we can identify them now more easily.
Even though the code seems to be FreeBSD kernel code, it isn't compiled
on FreeBSD. I could have known this, because I was a little amazed that
I couldn't find a prototype of pfopen()/pfclose() somewhere else,
because it isn't marked as static.
Apart from that, removing these functions wouldn't have been harmful
anyway, because there are some other strange things about them (the
implementation isn't consistent with the prototype at the top). Still,
it's better to leave it, because it makes merging code back to older
branches a little harder.
Requested by: mlaier
It turns out I was patching functions that weren't used by pf(4) anyway.
They still seem to use `struct proc *' instead of `struct thread *'.
They weren't listed in pf_cdevsw.
Because it is not possible to access the pf(4) character device through
any other device node as the one in devfs, there is no need to check for
unknown device minor numbers.
Approved by: mlaier
1. separating L2 tables (ARP, NDP) from the L3 routing tables
2. removing as much locking dependencies among these layers as
possible to allow for some parallelism in the search operations
3. simplify the logic in the routing code,
The most notable end result is the obsolescent of the route
cloning (RTF_CLONING) concept, which translated into code reduction
in both IPv4 ARP and IPv6 NDP related modules, and size reduction in
struct rtentry{}. The change in design obsoletes the semantics of
RTF_CLONING, RTF_WASCLONE and RTF_LLINFO routing flags. The userland
applications such as "arp" and "ndp" have been modified to reflect
those changes. The output from "netstat -r" shows only the routing
entries.
Quite a few developers have contributed to this project in the
past: Glebius Smirnoff, Luigi Rizzo, Alessandro Cerri, and
Andre Oppermann. And most recently:
- Kip Macy revised the locking code completely, thus completing
the last piece of the puzzle, Kip has also been conducting
active functional testing
- Sam Leffler has helped me improving/refactoring the code, and
provided valuable reviews
- Julian Elischer setup the perforce tree for me and has helped
me maintaining that branch before the svn conversion
variable in this copy of the code[1].
While here prefix the variables with 'pf_' to avoid file static global
variables with colliding names that are or will be virtualized.
Discussed with: rwatson, silby [1]
but formerly missed under VIMAGE_GLOBAL.
Put the extern declarations of the virtualized globals
under VIMAGE_GLOBAL as the globals themsevles are already.
This will help by the time when we are going to remove the globals
entirely.
Sponsored by: The FreeBSD Foundation
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
container structures, depending on VIMAGE_GLOBALS compile time option.
Make VIMAGE_GLOBALS a new compile-time option, which by default will not
be defined, resulting in instatiations of global variables selected for
V_irtualization (enclosed in #ifdef VIMAGE_GLOBALS blocks) to be
effectively compiled out. Instantiate new global container structures
to hold V_irtualized variables: vnet_net_0, vnet_inet_0, vnet_inet6_0,
vnet_ipsec_0, vnet_netgraph_0, and vnet_gif_0.
Update the VSYM() macro so that depending on VIMAGE_GLOBALS the V_
macros resolve either to the original globals, or to fields inside
container structures, i.e. effectively
#ifdef VIMAGE_GLOBALS
#define V_rt_tables rt_tables
#else
#define V_rt_tables vnet_net_0._rt_tables
#endif
Update SYSCTL_V_*() macros to operate either on globals or on fields
inside container structs.
Extend the internal kldsym() lookups with the ability to resolve
selected fields inside the virtualization container structs. This
applies only to the fields which are explicitly registered for kldsym()
visibility via VNET_MOD_DECLARE() and vnet_mod_register(), currently
this is done only in sys/net/if.c.
Fix a few broken instances of MODULE_GLOBAL() macro use in SCTP code,
and modify the MODULE_GLOBAL() macro to resolve to V_ macros, which in
turn result in proper code being generated depending on VIMAGE_GLOBALS.
De-virtualize local static variables in sys/contrib/pf/net/pf_subr.c
which were prematurely V_irtualized by automated V_ prepending scripts
during earlier merging steps. PF virtualization will be done
separately, most probably after next PF import.
Convert a few variable initializations at instantiation to
initialization in init functions, most notably in ipfw. Also convert
TUNABLE_INT() initializers for V_ variables to TUNABLE_FETCH_INT() in
initializer functions.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
directly include only the header files needed. This reduces the
unneeded spamming of various headers into lots of files.
For now, this leaves us with very few modules including vnet.h
and thus needing to depend on opt_route.h.
Reviewed by: brooks, gnn, des, zec, imp
Sponsored by: The FreeBSD Foundation
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
underneath #ifdef VIMAGE blocks.
This change introduces some churn in #include ordering and nesting
throughout the network stack and drivers but is not expected to cause
any additional issues.
In the next step this will allow us to instantiate the virtualization
container structures and switch from using global variables to their
"containerized" counterparts.
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
This means that inp_cred is always there, even after the socket
has gone away. It also means that it is constant for the lifetime
of the inp.
Both facts lead to simpler code and possibly less locking.
Suggested by: rwatson
Reviewed by: rwatson
MFC after: 6 weeks
X-MFC Note: use a inp_pspare for inp_cred
from the vimage project, as per plan established at devsummit 08/08:
http://wiki.freebsd.org/Image/Notes200808DevSummit
Introduce INIT_VNET_*() initializer macros, VNET_FOREACH() iterator
macros, and CURVNET_SET() context setting macros, all currently
resolving to NOPs.
Prepare for virtualization of selected SYSCTL objects by introducing a
family of SYSCTL_V_*() macros, currently resolving to their global
counterparts, i.e. SYSCTL_V_INT() == SYSCTL_INT().
Move selected #defines from sys/sys/vimage.h to newly introduced header
files specific to virtualized subsystems (sys/net/vnet.h,
sys/netinet/vinet.h etc.).
All the changes are verified to have zero functional impact at this
point in time by doing MD5 comparision between pre- and post-change
object files(*).
(*) netipsec/keysock.c did not validate depending on compile time options.
Implemented by: julian, bz, brooks, zec
Reviewed by: julian, bz, brooks, kris, rwatson, ...
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
virtualization work done by Marko Zec (zec@).
This is the first in a series of commits over the course
of the next few weeks.
Mark all uses of global variables to be virtualized
with a V_ prefix.
Use macros to map them back to their global names for
now, so this is a NOP change only.
We hope to have caught at least 85-90% of what is needed
so we do not invalidate a lot of outstanding patches again.
Obtained from: //depot/projects/vimage-commit2/...
Reviewed by: brooks, des, ed, mav, julian,
jamie, kris, rwatson, zec, ...
(various people I forgot, different versions)
md5 (with a bit of help)
Sponsored by: NLnet Foundation, The FreeBSD Foundation
X-MFC after: never
V_Commit_Message_Reviewed_By: more people than the patch
current@ and stable@ for the locking patches. The driver can always be
revived if someone tests it.
This driver also sleeps in its if_init routine, so it likely doesn't really
work at all anyway in modern releases.
- Add a mutex to the softc and use it to protect the softc and device
hardware.
- Setup interrupt handler after interface attach.
- Retire 'unit' from softc and use if_printf() instead.
- Don't frob IFF_UP in the driver.
- Use callout_() rather than timeout() and untimeout().
This particular implementation is designed to be fully backwards compatible
and to be MFC-able to 7.x (and 6.x)
Currently the only protocol that can make use of the multiple tables is IPv4
Similar functionality exists in OpenBSD and Linux.
From my notes:
-----
One thing where FreeBSD has been falling behind, and which by chance I
have some time to work on is "policy based routing", which allows
different
packet streams to be routed by more than just the destination address.
Constraints:
------------
I want to make some form of this available in the 6.x tree
(and by extension 7.x) , but FreeBSD in general needs it so I might as
well do it in -current and back port the portions I need.
One of the ways that this can be done is to have the ability to
instantiate multiple kernel routing tables (which I will now
refer to as "Forwarding Information Bases" or "FIBs" for political
correctness reasons). Which FIB a particular packet uses to make
the next hop decision can be decided by a number of mechanisms.
The policies these mechanisms implement are the "Policies" referred
to in "Policy based routing".
One of the constraints I have if I try to back port this work to
6.x is that it must be implemented as a EXTENSION to the existing
ABIs in 6.x so that third party applications do not need to be
recompiled in timespan of the branch.
This first version will not have some of the bells and whistles that
will come with later versions. It will, for example, be limited to 16
tables in the first commit.
Implementation method, Compatible version. (part 1)
-------------------------------
For this reason I have implemented a "sufficient subset" of a
multiple routing table solution in Perforce, and back-ported it
to 6.x. (also in Perforce though not always caught up with what I
have done in -current/P4). The subset allows a number of FIBs
to be defined at compile time (8 is sufficient for my purposes in 6.x)
and implements the changes needed to allow IPV4 to use them. I have not
done the changes for ipv6 simply because I do not need it, and I do not
have enough knowledge of ipv6 (e.g. neighbor discovery) needed to do it.
Other protocol families are left untouched and should there be
users with proprietary protocol families, they should continue to work
and be oblivious to the existence of the extra FIBs.
To understand how this is done, one must know that the current FIB
code starts everything off with a single dimensional array of
pointers to FIB head structures (One per protocol family), each of
which in turn points to the trie of routes available to that family.
The basic change in the ABI compatible version of the change is to
extent that array to be a 2 dimensional array, so that
instead of protocol family X looking at rt_tables[X] for the
table it needs, it looks at rt_tables[Y][X] when for all
protocol families except ipv4 Y is always 0.
Code that is unaware of the change always just sees the first row
of the table, which of course looks just like the one dimensional
array that existed before.
The entry points rtrequest(), rtalloc(), rtalloc1(), rtalloc_ign()
are all maintained, but refer only to the first row of the array,
so that existing callers in proprietary protocols can continue to
do the "right thing".
Some new entry points are added, for the exclusive use of ipv4 code
called in_rtrequest(), in_rtalloc(), in_rtalloc1() and in_rtalloc_ign(),
which have an extra argument which refers the code to the correct row.
In addition, there are some new entry points (currently called
rtalloc_fib() and friends) that check the Address family being
looked up and call either rtalloc() (and friends) if the protocol
is not IPv4 forcing the action to row 0 or to the appropriate row
if it IS IPv4 (and that info is available). These are for calling
from code that is not specific to any particular protocol. The way
these are implemented would change in the non ABI preserving code
to be added later.
One feature of the first version of the code is that for ipv4,
the interface routes show up automatically on all the FIBs, so
that no matter what FIB you select you always have the basic
direct attached hosts available to you. (rtinit() does this
automatically).
You CAN delete an interface route from one FIB should you want
to but by default it's there. ARP information is also available
in each FIB. It's assumed that the same machine would have the
same MAC address, regardless of which FIB you are using to get
to it.
This brings us as to how the correct FIB is selected for an outgoing
IPV4 packet.
Firstly, all packets have a FIB associated with them. if nothing
has been done to change it, it will be FIB 0. The FIB is changed
in the following ways.
Packets fall into one of a number of classes.
1/ locally generated packets, coming from a socket/PCB.
Such packets select a FIB from a number associated with the
socket/PCB. This in turn is inherited from the process,
but can be changed by a socket option. The process in turn
inherits it on fork. I have written a utility call setfib
that acts a bit like nice..
setfib -3 ping target.example.com # will use fib 3 for ping.
It is an obvious extension to make it a property of a jail
but I have not done so. It can be achieved by combining the setfib and
jail commands.
2/ packets received on an interface for forwarding.
By default these packets would use table 0,
(or possibly a number settable in a sysctl(not yet)).
but prior to routing the firewall can inspect them (see below).
(possibly in the future you may be able to associate a FIB
with packets received on an interface.. An ifconfig arg, but not yet.)
3/ packets inspected by a packet classifier, which can arbitrarily
associate a fib with it on a packet by packet basis.
A fib assigned to a packet by a packet classifier
(such as ipfw) would over-ride a fib associated by
a more default source. (such as cases 1 or 2).
4/ a tcp listen socket associated with a fib will generate
accept sockets that are associated with that same fib.
5/ Packets generated in response to some other packet (e.g. reset
or icmp packets). These should use the FIB associated with the
packet being reponded to.
6/ Packets generated during encapsulation.
gif, tun and other tunnel interfaces will encapsulate using the FIB
that was in effect withthe proces that set up the tunnel.
thus setfib 1 ifconfig gif0 [tunnel instructions]
will set the fib for the tunnel to use to be fib 1.
Routing messages would be associated with their
process, and thus select one FIB or another.
messages from the kernel would be associated with the fib they
refer to and would only be received by a routing socket associated
with that fib. (not yet implemented)
In addition Netstat has been edited to be able to cope with the
fact that the array is now 2 dimensional. (It looks in system
memory using libkvm (!)). Old versions of netstat see only the first FIB.
In addition two sysctls are added to give:
a) the number of FIBs compiled in (active)
b) the default FIB of the calling process.
Early testing experience:
-------------------------
Basically our (IronPort's) appliance does this functionality already
using ipfw fwd but that method has some drawbacks.
For example,
It can't fully simulate a routing table because it can't influence the
socket's choice of local address when a connect() is done.
Testing during the generating of these changes has been
remarkably smooth so far. Multiple tables have co-existed
with no notable side effects, and packets have been routes
accordingly.
ipfw has grown 2 new keywords:
setfib N ip from anay to any
count ip from any to any fib N
In pf there seems to be a requirement to be able to give symbolic names to the
fibs but I do not have that capacity. I am not sure if it is required.
SCTP has interestingly enough built in support for this, called VRFs
in Cisco parlance. it will be interesting to see how that handles it
when it suddenly actually does something.
Where to next:
--------------------
After committing the ABI compatible version and MFCing it, I'd
like to proceed in a forward direction in -current. this will
result in some roto-tilling in the routing code.
Firstly: the current code's idea of having a separate tree per
protocol family, all of the same format, and pointed to by the
1 dimensional array is a bit silly. Especially when one considers that
there is code that makes assumptions about every protocol having the
same internal structures there. Some protocols don't WANT that
sort of structure. (for example the whole idea of a netmask is foreign
to appletalk). This needs to be made opaque to the external code.
My suggested first change is to add routing method pointers to the
'domain' structure, along with information pointing the data.
instead of having an array of pointers to uniform structures,
there would be an array pointing to the 'domain' structures
for each protocol address domain (protocol family),
and the methods this reached would be called. The methods would have
an argument that gives FIB number, but the protocol would be free
to ignore it.
When the ABI can be changed it raises the possibilty of the
addition of a fib entry into the "struct route". Currently,
the structure contains the sockaddr of the desination, and the resulting
fib entry. To make this work fully, one could add a fib number
so that given an address and a fib, one can find the third element, the
fib entry.
Interaction with the ARP layer/ LL layer would need to be
revisited as well. Qing Li has been working on this already.
This work was sponsored by Ironport Systems/Cisco
Reviewed by: several including rwatson, bz and mlair (parts each)
Obtained from: Ironport systems/Cisco
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
when reading credential data from sockets.
Teach pf to unlock the pcbinfo more quickly once it has acquired an
inpcb lock, as the inpcb lock is sufficient to protect the reference.
Assert locks, rather than read locks or write locks, on inpcbs in
subroutines--this is necessary as the inpcb may be passed down with a
write lock from the protocol, or may be passed down with a read lock
from the firewall lookup routine, and either is sufficient.
MFC after: 3 months
explicitly select write locking for all use of the inpcb mutex.
Update some pcbinfo lock assertions to assert locked rather than
write-locked, although in practice almost all uses of the pcbinfo
rwlock main exclusive, and all instances of inpcb lock acquisition
are exclusive.
This change should introduce (ideally) little functional change.
However, it lays the groundwork for significantly increased
parallelism in the TCP/IP code.
MFC after: 3 months
Tested by: kris (superset of committered patch)
and netgraph in gernal). This also allows to add queues for an interface
that is not yet existing (you have to provide the bandwidth for the
interface, however).
PR: kern/106400, kern/117827
MFC after: 2 weeks
user-mode lock manager, build a kernel with the NFSLOCKD option and
add '-k' to 'rpc_lockd_flags' in rc.conf.
Highlights include:
* Thread-safe kernel RPC client - many threads can use the same RPC
client handle safely with replies being de-multiplexed at the socket
upcall (typically driven directly by the NIC interrupt) and handed
off to whichever thread matches the reply. For UDP sockets, many RPC
clients can share the same socket. This allows the use of a single
privileged UDP port number to talk to an arbitrary number of remote
hosts.
* Single-threaded kernel RPC server. Adding support for multi-threaded
server would be relatively straightforward and would follow
approximately the Solaris KPI. A single thread should be sufficient
for the NLM since it should rarely block in normal operation.
* Kernel mode NLM server supporting cancel requests and granted
callbacks. I've tested the NLM server reasonably extensively - it
passes both my own tests and the NFS Connectathon locking tests
running on Solaris, Mac OS X and Ubuntu Linux.
* Userland NLM client supported. While the NLM server doesn't have
support for the local NFS client's locking needs, it does have to
field async replies and granted callbacks from remote NLMs that the
local client has contacted. We relay these replies to the userland
rpc.lockd over a local domain RPC socket.
* Robust deadlock detection for the local lock manager. In particular
it will detect deadlocks caused by a lock request that covers more
than one blocking request. As required by the NLM protocol, all
deadlock detection happens synchronously - a user is guaranteed that
if a lock request isn't rejected immediately, the lock will
eventually be granted. The old system allowed for a 'deferred
deadlock' condition where a blocked lock request could wake up and
find that some other deadlock-causing lock owner had beaten them to
the lock.
* Since both local and remote locks are managed by the same kernel
locking code, local and remote processes can safely use file locks
for mutual exclusion. Local processes have no fairness advantage
compared to remote processes when contending to lock a region that
has just been unlocked - the local lock manager enforces a strict
first-come first-served model for both local and remote lockers.
Sponsored by: Isilon Systems
PR: 95247 107555 115524 116679
MFC after: 2 weeks
after each SYSINIT() macro invocation. This makes a number of
lightweight C parsers much happier with the FreeBSD kernel
source, including cflow's prcc and lxr.
MFC after: 1 month
Discussed with: imp, rink
always curthread.
As KPI gets broken by this patch, manpages and __FreeBSD_version will be
updated by further commits.
Tested by: Andrea Barberio <insomniac at slackware dot it>
namespace in order to handle lockmgr fields in a controlled way instead
than spreading all around bogus stubs:
- VN_LOCK_AREC() allows lock recursion for a specified vnode
- VN_LOCK_ASHARE() allows lock sharing for a specified vnode
In FFS land:
- BUF_AREC() allows lock recursion for a specified buffer lock
- BUF_NOREC() disallows recursion for a specified buffer lock
Side note: union_subr.c::unionfs_node_update() is the only other function
directly handling lockmgr fields. As this is not simple to fix, it has
been left behind as "sole" exception.
conjuction with 'thread' argument passing which is always curthread.
Remove the unuseful extra-argument and pass explicitly curthread to lower
layer functions, when necessary.
KPI results broken by this change, which should affect several ports, so
version bumping and manpage update will be further committed.
Tested by: kris, pho, Diego Sardina <siarodx at gmail dot com>
zone code. The GPE handler method (i.e. _L00) generates various Notify
events that need to be run to completion before the GPE is re-enabled.
In ACPI-CA, we queue an asynch callback at the same priority as a Notify
so that it will only run after all Notify handlers have completed. The
callback re-enables the GPE afterwards. We also changed the priority of
Notifies to be the same as GPEs, given the possibility that another GPE
could arrive before the Notifies have completed and we don't want it to
get queued ahead of the rest.
The ACPI-CA change was submitted by Alexey Starikovskiy (SUSE) and will
appear in a later release. Special thanks to him for helping track this
bug down.
MFC after: 1 week
Tested by: jhb, Yousif Hassan <yousif / alumni.jmu.edu>
Remove this argument and pass curthread directly to underlying
VOP_LOCK1() VFS method. This modify makes the code cleaner and in
particular remove an annoying dependence helping next lockmgr() cleanup.
KPI results, obviously, changed.
Manpage and FreeBSD_version will be updated through further commits.
As a side note, would be valuable to say that next commits will address
a similar cleanup about VFS methods, in particular vop_lock1 and
vop_unlock.
Tested by: Diego Sardina <siarodx at gmail dot com>,
Andrea Di Pasquale <whyx dot it at gmail dot com>
1837014 Kernel panics after authentication of an outgoing packet
1836992 Potential bugs in packet auth code (w/patches)
1836967 Kernel panic when using auth rule with keep state
and another reported only to FreeBSD by Andiry (see PR)
PR: kern/118251
Submitted by: Andriy Syrovenko <andriys@gmail.com>
Reviewed by: darrenr
MFC after: 5 days
This import includes:
o wpi Wireless driver for the Intel 3945 Wireless Lan Controller (802.11abg) (sys/dev/wpi)
o Intel firmware revision 2.14.4 & associated LICENSE (sys/dev/contrib/wpi, sys/contrib/dev/wpi/LICENSE)
o wpifw Firmware driver (sys/modules/wpifw)
Approved by: mlaier, sam (co-mentors)
(BIO_WRITE and BIO_FLUSH) as it is done is Solaris. The difference is
that Solaris calls it only for sync requests, but we can't say in GEOM
is the request is sync or async, so we do it for every request.
MFC after: 1 week
* Do not hold any locks over calls to copyin/copyout.
* Clean up some #ifdefs
* fix a possible mbuf leak when NAT fails on policy routed packets
PR: 117216
Framework by moving from mac_mbuf_create_netlayer() to more specific
entry points for specific network services:
- mac_netinet_firewall_reply() to be used when replying to in-bound TCP
segments in pf and ipfw (etc).
- Rename mac_netinet_icmp_reply() to mac_netinet_icmp_replyinplace() and
add mac_netinet_icmp_reply(), reflecting that in some cases we overwrite
a label in place, but in others we apply the label to a new mbuf.
Obtained from: TrustedBSD Project
we move towards netinet as a pseudo-object for the MAC Framework.
Rename 'mac_create_mbuf_linklayer' to 'mac_mbuf_create_linklayer' to
reflect general object-first ordering preference.
Sponsored by: SPARTA (original patches against Mac OS X)
Obtained from: TrustedBSD Project, Apple Computer
from Mac OS X Leopard--rationalize naming for entry points to
the following general forms:
mac_<object>_<method/action>
mac_<object>_check_<method/action>
The previous naming scheme was inconsistent and mostly
reversed from the new scheme. Also, make object types more
consistent and remove spaces from object types that contain
multiple parts ("posix_sem" -> "posixsem") to make mechanical
parsing easier. Introduce a new "netinet" object type for
certain IPv4/IPv6-related methods. Also simplify, slightly,
some entry point names.
All MAC policy modules will need to be recompiled, and modules
not updates as part of this commit will need to be modified to
conform to the new KPI.
Sponsored by: SPARTA (original patches against Mac OS X)
Obtained from: TrustedBSD Project, Apple Computer
to kproc_xxx as they actually make whole processes.
Thos makes way for us to add REAL kthread_create() and friends
that actually make theads. it turns out that most of these
calls actually end up being moved back to the thread version
when it's added. but we need to make this cosmetic change first.
I'd LOVE to do this rename in 7.0 so that we can eventually MFC the
new kthread_xxx() calls.
After discussion with Sam, switch back to use firmware(9) instead of
having the firmware in hex format.
Put the binary firmware uuencoded into sys/contrib/dev/npe, and slap a
LICENSE file, as found on the Intel website.
Approved by: re (blanket), mux (mentor)
MFC After: 1 week
This patch was part of ACPI-CA 20070508 release and the
following is excerpt from its change log:
Fixed a problem where the Global Lock handle was not properly
updated if a thread that acquired the Global Lock via executing
AML code then attempted to acquire the lock via the
AcpiAcquireGlobalLock interface. Reported by Joe Liu.
Approved by: re (kensmith)
Tested by: ambrisko
Obtained from: Intel
value, so we don't run out of KVA. The default vnodes limit fits better for
UFS, but ZFS allocated more file system specific memory for a vnode than UFS.
Don't touch vnodes limit if we detect it was tuned by system administrator
and restore original value when ZFS is unloaded.
This isn't final fix, but before we implement something better, this will
help to stabilize ZFS under heavy load on i386.
Approved by: re (bmah)
ICMP error message, do not access th_flags. The field is beyond
the first eight bytes of the header that are required to be present
and were pulled up in the mbuf.
A random value of th_flags can have TH_SYN set, which made the
sequence number comparison not apply the window scaling factor,
which led to legitimate ICMP(v6) packets getting blocked with
"BAD ICMP" debug log messages (if enabled with pfctl -xm), thus
breaking PMTU discovery.
Triggering the bug requires TCP window scaling to be enabled
(sysctl net.inet.tcp.rfc1323, enabled by default) on both end-
points of the TCP connection. Large scaling factors increase
the probability of triggering the bug.
PR: kern/115413: [ipv6] ipv6 pmtu not working
Tested by: Jacek Zapala
Reviewed by: mlaier
Approved by: re (kensmith)
Rev 1.9 introduced another path where machclk_freq would be initialized
before the rest of setup was done (i.e. initializing the callout). Make
the one-time initialization a separate function and make init_machclk()
able to be called multiple times, any time. We depend on tsc_freq first
being updated from the highest priority eventhandler, thus we run last
and call init_machclk() to set machclk_freq. Also, don't initialize
static variables to 0.
Tested by: Eygene Ryabinkin
Approved by: re
