making the use of sc_hwmap to do direct mapping impractical. Switch to
indexing by the rate index instead of the rate code and adjust associated
state and logic appropriately. This has several benefits including
simplification of the led code.
o fix radiotap capture of HT rates
o fix conditional compilation of HT radiotap support to be based on the
hal having 5416 support; not the ABI version as hal builds may or may
not include 5416 support
o update tx rssi data only when an ACK was received
o return tx rssi from sampled data instead of the last frame
o track noise floor
o return rx rssi and noise floor (was broken)
o pass country code, outdoor indication, and ecm mode into the hal
when requesting a channel list
o add a console msg when regulatory setup fails
o add placeholder code to map between Atheros sku's and 802.11 sku's
that handles only the debug country code used to unlock the full
channel list (to be used only for debugging)
o fix multiple instances of mismapping the 802.11 location to the
outdoor indication (anywhere may be outdoor also)
in sta and adhoc modes; this should've been done forever ago as most all
drivers use this hook to set per-station transmit parameters such as for
tx rate control
o adjust drivers to remove explicit calls to the driver newassoc method
The cn_unit and cn_tp fields don't seem to be used anywhere. Some
drivers set them, while others don't. Just remove them, in an attempt to
make our consdev code a little easier to understand.
G3 as well as the internal ADB keyboard and mice in PowerBooks and iBooks. This
also brings in Mac GPIO support, for which we should eventually have a better
interface.
Obtained from: NetBSD (CUDA and PMU drivers)
Olaf Kirch noticed that the i915_set_status_page() function of the i915
kernel driver calls ioremap with an address offset that is supplied by
userspace via ioctl. The function zeroes the mapped memory via memset
and tells the hardware about the address. Turns out that access to that
ioctl is not restricted to root so users could probably exploit that to
do nasty things. We haven't tried to write actual exploit code though.
It only affects the Intel G33 series and newer.
Approved by: bz (secteam)
Obtained from: Intel drm repo
Security: CVE-2008-3831
Memory Interface (CFI). The flash memory can be read and written
to through /dev/cfi# and an ioctl() exists so processes can read
the query information.
The driver supports the AMD and Intel command set, though only
the AMD command has been tested.
Obtained from: Juniper Networks, Inc.
with several points unappropriate for the present parser. This patch
disables input-to-output analog monitoring but instead fixes recording.
Tested by Tobias Grosser on ThinkPad T61p.
might make Qualcomm and Option cards (which have all endpoints in 1
interface) work.
- Change the USB buffer sizes to depend on the transfer speed. With UMTS
we use a buffer 384k / 1000 frames/sec * 50msecs =~ 15kB for example.
- Add a MODULE_VERSION statement
but I inadvertently overwrote the change when I synced to git. Commit
the fix in both places, so this doesn't happen again.
Approved by: jhb (mentor)
MFC after: 2 weeks
This update fixes a transmit bug in the multi-queue (MSI-X) firmware
which happens when RDMAs complete out of order, and provides
improved support for the new Myri10GE NIC models (10G-PCIE-8Bx)
Sponsored by: Myricom Inc.
MFC after:3 days
With our new TTY layer we use a two step device destruction procedure.
The TTY first gets abandoned by the device driver. When the TTY layer
notices all threads have left the TTY layer, it deallocates the TTY.
This means that the device unit number should not be reused before a
callback from the TTY layer to the device driver has been made. newbus
doesn't seem to support this concept (yet), so right now just add a
destructor with a big comment in it. It's not ideal, but at least it's
better than panicing.
Reported by: rnoland
Driver supports PCI devices with class 8 and subclass 5 according to
SD Host Controller Specification.
Update NOTES, enable module and static build.
Enable related mmc and mmcsd modules build.
Discussed on: mobile@, current@
other fixes:
- Add pointers back to device_t objects in softc structures instead
of storing the unit and using devclass_get_device().
- Add 'lpbb', 'pcf', 'pps', and 'vpo' child devices to every 'ppbus' device
instead of just the first one.
- Store softc pointers in si_drv1 of character devices instead of
pulling the unit number from the minor number and using
devclass_get_softc() and devclass_get_device().
- Store the LP_BYPASS flag in si_drv2 instead of encoding it in the minor
number.
- Destroy character devices for lpt(4) when detaching the device.
- Use bus_print_child_footer() instead of duplicating it in
ppbus_print_child() and fix ppbus_print_child()'s return value.
- Remove unused AVM ivar from ppbus.
- Don't store the 'mode' ivar in the ppbus ivars since we always fetch it
from the parent anyway.
- Try to detach all the child devices before deleting them in
ppbus_detach().
- Use pause() instead of a tsleep() on a dummy address when polling the
ppbus.
- Use if_printf() and device_printf() instead of explicit names with unit
numbers.
Silence on: current@
Erase operation gives card's logic information about unused areas to help it
implement wear-leveling with lower overhead comparing to usual writing.
Erase is much faster then write and does not depends on data bus speed.
Also as result of hitting in-card write logic optimizations I have measured
up to 50% performance boost on writing undersized blocks into preerased areas.
At the same time there are strict limitations on size and allignment of erase
operations. We can erase only blocks aligned to the erase sector size and
with size multiple of it. Different cards has different erase sector size
which usually varies from 64KB to 4MB. SD cards actually allow to erase
smaller blocks, but it is much more expensive as it is implemented via
read-erase-write sequence and so not sutable for the BIO_DELETE purposes.
Reviewed by: imp@
(still a power of 2) rather than 63k transfers. Even with 63k transfers
some machines (such as Dell SC1435's) were experiencing chronic data
corruption.
- Use the MIO method to talk to the Serverworks HT1000_S1 SATA controller
like all the other SATA controllers rather than the compat PATA
method. This lets the controller see all 4 SATA ports and also
matches the behavior of the Linux driver.
Silence from: sos
MFC after: 3 days
bank instead of copper/fiber bank which in turn resulted in
wrong registers were accessed during PHY operation. It is
believed that page 0 should be used for copper PHY so reinitialize
E1000_EADR to select default copper PHY.
This fixes link establishment issue of nfe(4) on Sun Fire X4140.
OpenBSD also has similimar patch but they just reset the E1000_EADR
register to page 0. However some Marvell PHYs((88E3082, 88E1000)
don't have the extended address register and the meaning of the
register is quite different for each PHY model. So selecting copper
PHY is limited to 88E1149 PHY which seems to be the only one that
exhibits link establishment problem. If parent device know the type
of PHY(either copper or fiber) that information should be notified
to PHY driver but there is no good way to pass this information yet.
Reported by: thompsa
Reviewed by: thompsa
the Sierra and Novatel devices, ignore all umass devices and hide the umass
devices that represent the CD ROM devices (but not the SD card slot in the
Huawei Mobile dongle).
Note: This driver in FBSD7 seems to suffer from memory corruption when used
with an Option GT Quad. The E220 however works flawlessly.
Also add the ID for the Option GTMaxHSUPA, provided by Olivier Fromme.
o better quality of the movement smoothing
o more features such as tap-hold and virtual scrolling
Support must still be enabled with this line in your /boot/loader.conf:
hw.psm.synaptics_support="1"
The following sysctls were removed:
hw.psm.synaptics.low_speed_threshold
hw.psm.synaptics.min_movement
hw.psm.synaptics.squelch_level
An overview of this new driver and a short documentation about the added
sysctls is available on the wiki:
http://wiki.freebsd.org/SynapticsTouchpad
simplifies certain device attachments (Kauai ATA, for instance), and makes
possible others on new hardware.
On G5 systems, there are several otherwise standard PCI devices
(Serverworks SATA) that will not allow their interrupt properties to be
written, so this information must be supplied directly from Open Firmware.
Obtained from: sparc64
This supports 1Gbps Ethernet engine found on ARM-based SOCs (Orion, Kirkwood,
Discovery), as well as on system controllers for PowerPC processors (MV64430,
MV6446x).
The following advanced features are supported:
- multicast
- VLAN tagging
- IP/TCP/UDP checksum calculation offloading
- polling
- interrupt coalescing
Obtained from: Marvell, Semihalf
the last byte of the ethernet address was not read which in turn
resulted in getting 5 out of the 6 bytes of ethernet address and
always returned ENOENT. I did not notice the bug on FPGA version
because of additional configuration data in EEPROM.
Pointed out by: bouyer at NetBSD
example the Huawei Mobile has an SD card slot on the second interface.
- Do not attach to Qualcomm and Novatel cards. If ignored these cards will
switch to modem mode automatically it seems.
- Reduce the priority on generic attachment to the appropriate level.
Note: A better solution is to send an eject command straightaway, but that can
be left till later.
* Orion
- 88F5181
- 88F5182
- 88F5281
* Kirkwood
- 88F6281
* Discovery
- MV78100
The above families of SOCs are built around CPU cores compliant with ARMv5TE
instruction set architecture definition. They share a number of integrated
peripherals. This commit brings support for the following basic elements:
* GPIO
* Interrupt controller
* L1, L2 cache
* Timers, watchdog, RTC
* TWSI (I2C)
* UART
Other peripherals drivers will be introduced separately.
Reviewed by: imp, marcel, stass (Thanks guys!)
Obtained from: Marvell, Semihalf
will ease the identification of memory leaks as the OS will be able to track
allocations for us by malloc type. vmstat -m will show all of the
allocations.
Convert the calls to drm_alloc() and friends, which are used in shared code
to static __inline__ while we are here.
Approved by: jhb (mentor)
from operating on a list with a single item. This code is used much more by
the i915 driver with xorg-7.4. Correct it to match the actual linux
implementation.
Approved by: jhb (mentor)
busmastering support. This also adds register definitions for MSI support,
which we will be using shortly.
Approved by: jhb (mentor)
Obtained from: drm git master
macio's enable-enet word, which apparently does nothing on some machines,
open an OF instance of the ethernet controller. This fixes cold booting
from disk on my Blue & White G3.
MFC after: 3 days
device id is JMC260 family. Previously it just verified the deivce
is JMC260 Rev A0. This will make it easy for newer JMC2xx support.
Pointed out by: bouyer at NetBSD
This was located in the ubsa driver, but should be moved into a separate
driver:
- 3G modems provide multiple serial ports to allow AT commands while the PPP
connection is up.
- 3G modems do not provide baud rate or other serial port settings.
- Huawei cards need specific initialisation.
- ubsa is for Belkin adapters, an Linuxy choice for another device like 3G.
Speeds achieved here with a weak signal at best is ~40kb/s (UMTS). No spooky
STALLED messages as well.
Next: Move over all entries for Sierra and Novatel cards once I have found
testers, and implemented serial port enumeration for Sierra (or rather have
Andrea Guzzo do it). They list all endpoints in 1 iface instead of 4 ifaces.
Submitted by: aguzzo@anywi.com
MFC after: 3 weeks
have in common right now is a memset. This saves a parameter to
these routines, as well as a level of indentation.
o Make mmc_get_bits a little clearer... It really only works on 128-bit
registers right now.
reduce ABI disruptions when new cpu types and new PMC events are added
in the future.
- Support alternate spellings for PMC events. Derive the canonical
spelling of an event name from its enumeration name in 'enum pmc_event'.
- Provide a way for users to disambiguate between identically named events
supported by multiple classes of PMCs in a CPU.
- Change libpmc's machine-dependent event specifier parsing code to
better support CPUs containing two or more classes of PMC resources.
If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.
However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:
atacore: ATA core functionality, always needed for any ATA setup
atacard: CARDBUS support
atacbus: PC98 cbus support
ataisa: ISA bus support
atapci: PCI bus support only generic chipset support.
ataahci: AHCI support, also pulled in by some vendor modules.
ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia; Vendor support, ie atavia for VIA chipsets
atadisk: ATA disk driver
ataraid: ATA softraid driver
atapicd: ATAPI cd/dvd driver
atapifd: ATAPI floppy/flashdisk driver
atapist: ATAPI tape driver
atausb: ATA<>USB bridge
atapicam: ATA<>CAM bridge
This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:
device atacore
device atapci
device atavia
And then you need the atadisk, atapicd etc lines in there just as usual.
If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.
can reliably provoke data corruption on systems equipped with a
plenty of memory during high load.
Reported by: gnn via iXsystems
MFC candidate: RELENG_7_1, RELENG_7
We don't explicity check for error here and M_WAITOK will just put the
process to sleep waiting on resources to become available.
Suggested by jhb@
Approved by: jhb (mentor)
in GENERIC and LINT. [1]
- Rename hpt_dbg_level to hpt_iop_dbg_level to avoid multiple definition
of hpt_dbg_level (hptmv also has hpt_dbg_level).
PR: 127551 [1]
Reviewed by: scottl@
MFC after: 1 month
NDIS_TXPKTS and don't allocate unused extra spaces for sc->ndis_txarray
and sc->ndis_txpool.
PR: kern/127644
Submitted by: Antoine Pelisse <apelisse_at_gmail.com>
MFC after: 1 week
This reverts a private patch which is causing issues with many Intel chipsets.
I will review that patch and see what we need to do to fix it up later, but
for the time being, we will just get these chips working again.
This update contains a lot of code cleanup and is post gem merge
(no, we don't have gem support). It should prove much easier to read the
code now. A lot of thanks goes to vehemens for that work. I have adapted
the code to use cdevpriv for tracking per open file data. That alleviates
the old ugly hack that we used to try and accomplish the task and helped to
clean up the open / close behavior a good bit. This also replaces the hack
that was put in place a year or so ago to prevent radeons from locking up
with AIGLX enabled. I have had a couple of radeon testers report that it
still works as expected, though I no longer have radeon hardware to test with
myself. Other various fixes from the linux crew and Intel, many of
which are muddled in with the gem merge.
Approved by: jhb (mentor)
Obtained from: mesa/drm git master
MFC after: 2 weeks
obtained from Linux forcedeth driver.
While I'm here move creating a sysctl node for process_limit to
function nfe_sysctl_node().
Tested by: "Arno J. Klaassen" < arno <at> heho dot snv dot jussieu dot fr >
g33 based chips use a different method of identifying the gtt size.
g45 based chips gtt is located in a different area of stolen memory.
Approved by: jhb (mentor)
MFC after: 2 weeks
from the vimage project, as per plan established at devsummit 08/08:
http://wiki.freebsd.org/Image/Notes200808DevSummit
Introduce INIT_VNET_*() initializer macros, VNET_FOREACH() iterator
macros, and CURVNET_SET() context setting macros, all currently
resolving to NOPs.
Prepare for virtualization of selected SYSCTL objects by introducing a
family of SYSCTL_V_*() macros, currently resolving to their global
counterparts, i.e. SYSCTL_V_INT() == SYSCTL_INT().
Move selected #defines from sys/sys/vimage.h to newly introduced header
files specific to virtualized subsystems (sys/net/vnet.h,
sys/netinet/vinet.h etc.).
All the changes are verified to have zero functional impact at this
point in time by doing MD5 comparision between pre- and post-change
object files(*).
(*) netipsec/keysock.c did not validate depending on compile time options.
Implemented by: julian, bz, brooks, zec
Reviewed by: julian, bz, brooks, kris, rwatson, ...
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
- Support for Myricom 10G-PCIE-8B NICs
- multi-slice firmware: fix a bug when the presence of 32-bit or
64-bit DMA addresses for interrupt queues and data is not uniform across
slices.
- Improves automatic selection between ethp_z8e/eth_z8e
Sponsored by: Myricom Inc.
- simplify page hold logic
- allow pages for processes other than that of curthread to
have pages held
- normalize the interface to more closely resemble the functions in
sys/vm
MFC after: 1 week
only mode and restore original value of extended address register
instead of overwriting it with page 1. There are still instance
information passing issue(e.g configured media type: fiber or
copper) from driver to PHY layer but this change make the selected
PHY work with 88E1112 PHY.
Reported by: Krzysztof Jedruczyk < beaker <at> hot dot pl >
Tested by: Krzysztof Jedruczyk < beaker <at> hot dot pl >
This should fix occasional Tx checksum corruption issue.
Reported by: Garrett Cooper < yanefbsd <at> gmail dot com >
Tested by: Garrett Cooper < yanefbsd <at> gmail dot com >
disabled by default because there's problems with it on AT91RM9200,
currently the only host controller in the tree. I've not had time to
track those problems to ground. I'm committing because this is
important for other host controllers that are in the pipeline.
Submitted by: mav@
but an RW mapping exists for the underlying page. This change fixes the bug by using the
page / NULL returned from pmap_extract_and_hold to determine whether or not vm_fault needs
to be called.
The bug was pointed out by alc.
MFC after: 3 days
former more explicitly tells the compiler that you want an empty loop.
There are some lint programs that use this hint to avoid generating
warnings.
No functional change...
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
When I changed kern_conf.c three months ago I made device unit numbers
equal to (unneeded) device minor numbers. We used to require
bitshifting, because there were eight bits in the middle that were
reserved for a device major number. Not very long after I turned
dev2unit(), minor(), unit2minor() and minor2unit() into macro's.
The unit2minor() and minor2unit() macro's were no-ops.
We'd better not remove these four macro's from the kernel, because there
is a lot of (external) code that may still depend on them. For now it's
harmless to remove all invocations of unit2minor() and minor2unit().
Reviewed by: kib
Thanks goes to ITE who provided docs and feedback and made this possible.
Minor fixups to the Intel ICH code for bugs found while doing this.
(ITE8213 is very semilar to an Intel ICH)
MFC after: 1 week
Kick the device into the right mode if it comes up as a flash-disk.
Set the buffers to a sensible 1024 bytes instead of a far too small
default.
Don't attempt to change speed, baud, parity and such, the device does
not understand it.
have hardware ram buffer. The silicon bug seem to be triggered by
pause frames if receive buffer is not aligned on FIFO word(8 bytes).
To workaround the issue, make sure to align Rx buffers on 8 bytes.
Unfortunately this workaround requires yet another Rx fixup for
strict alignment architecture machines to align IP header.
For newer hardwares that lacks ram buffer may not have this bug so
check number of available ram buffer size to see the existence of
ram buffer.
Reported by: Ian Freislich (ianf <at> clue dot co dot za), das
Tested by: Ian Freislich (ianf <at> clue dot co dot za)
containing an Ethernet address fitted as this is yet another thing
that fails in that case in order to avoid the one second delay
until pci_read_vpd_reg() times out.
- Const'ify the bge_devs array.
when it runs on half-duplex media.
While I'm here add register definition for GPREG1. ATM the GPREG1
register is only valid for JMC250 A1/A2.
Submitted by: Ethan at JMicron
o don't use the key index to identify when the driver has been
asked to allocate a key slot, use an explicit flag; allows
drivers to force s/w fallback for entries in the global table
o change callback api to allocate driver resources for a crypto key:
- de-const the key parameter so drivers can muck with the flags
- on callback failure don't automatically try to setup s/w crypto;
instead the driver must now mark the key entry for s/w crypto and
the caller will re-attach the cipher module
NB: api change permits drivers more control over fallback to s/w
crypto (e.g. based on a limited number of h/w key slots)
to vga_pci.c to request on behalf of it's children. This causes vgapci to show
up as the interrupt owner in vmstat -i, rather than the child device.
Approved by: jhb(mentor)
kib@ and I have decided we will MFC the bpf(4)/snp(4) fixes after we've
released 7.1. Make sure the code in HEAD doesn't refer to a flag we
don't need anyway.
snp(4) in the MPSAFE TTY P4 branch already works, but still needs some
polishing before it can be integrated to SVN.
