The check for early exit should be checking the SLB entry itself. As
currently written it was checking the address of the SLB, which is always
non-zero, so would go through the kernel SR restore loop regardless.
Submitted by: mmacy
MFC after: 2 weeks
The second statements on the lines are not guarded by the `if' condition.
This triggers a warning with newer gcc. It's relatively harmless given the
usage, but incorrect. Instead, wrap the statements so they're properly
guarded.
Reported by: powerpc64-gcc xtoolchain
MFC after: 1 week
Chacha20 with a 256 bit key and 128 bit counter size is a good match for an
AES256-ICM replacement.
In userspace, Chacha20 is typically marginally slower than AES-ICM on
machines with AESNI intrinsics, but typically much faster than AES on
machines without special intrinsics. ChaCha20 does well on typical modern
architectures with SIMD instructions, which includes most types of machines
FreeBSD runs on.
In the kernel, we can't (or don't) make use of AESNI intrinsics for
random(4) anyway. So even on amd64, using Chacha provides a modest
performance improvement in random device throughput today.
This change makes the stream cipher used by random(4) configurable at boot
time with the 'kern.random.use_chacha20_cipher' tunable.
Very rough, non-scientific measurements at the /dev/random device, on a
GENERIC-NODEBUG amd64 VM with 'pv', show a factor of 2.2x higher throughput
for Chacha20 over the existing AES-ICM mode.
Reviewed by: delphij, markm
Approved by: secteam (delphij)
Differential Revision: https://reviews.freebsd.org/D19475
When we roam between networks and our link-state goes down, automatically remove
the IPv6-Only flag from the interface. Otherwise we might switch from an
IPv6-only to and IPv4-only network and the flag would stay and we would prevent
IPv4 from working.
While the actual function call to clear the flag is under EXPERIMENTAL,
the eventhandler is not as we might want to re-use it for other
functionality on link-down event (such was re-calculate default routers
for example if there is more than one).
Reviewed by: hrs
Differential Revision: https://reviews.freebsd.org/D19487
I just found that at least on Skylake CPUs cpu_ticks() never returns odd
values, only even, and possibly has even bigger step (176/2?), that makes
its lower bits very bad entropy source, leaving half of taskqueues unused.
Switch to sbinuptime(), closer to upstreams, mitigates the problem by the
rate conversion working as kind of hash function. In case that is somehow
not enough (timer rate is too low or too divisible) mix in curcpu.
MFC after: 1 week
dyn_install_state() uses `rule` pointer when it creates state.
For O_LIMIT states this pointer actually is not struct ip_fw,
it is pointer to O_LIMIT_PARENT state, that keeps actual pointer
to ip_fw parent rule. Thus we need to cache rule id and number
before calling dyn_get_parent_state(), so we can use them later
when the `rule` pointer is overrided.
PR: 236292
MFC after: 3 days
On GENERIC kernels with empty loader.conf, there is no functional change.
DFLTPHYS and MAXBSIZE are both 64kB at the moment. This change allows
larger bufcache block sizes to be used when either MAXBSIZE (custom kernel)
or the loader.conf tunable vfs.maxbcachebuf (GENERIC) is adjusted higher
than the default.
Suggested by: ken@
All changes are hidden behind the EXPERIMENTAL option and are not compiled
in by default.
Add ND6_IFF_IPV6_ONLY_MANUAL to be able to set the interface into no-IPv4-mode
manually without router advertisement options. This will allow developers to
test software for the appropriate behaviour even on dual-stack networks or
IPv6-Only networks without the option being set in RA messages.
Update ifconfig to allow setting and displaying the flag.
Update the checks for the filters to check for either the automatic or the manual
flag to be set. Add REVARP to the list of filtered IPv4-related protocols and add
an input filter similar to the output filter.
Add a check, when receiving the IPv6-Only RA flag to see if the receiving
interface has any IPv4 configured. If it does, ignore the IPv6-Only flag.
Add a per-VNET global sysctl, which is on by default, to not process the automatic
RA IPv6-Only flag. This way an administrator (if this is compiled in) has control
over the behaviour in case the node still relies on IPv4.
When open(2) was invoked against a FUSE filesystem with an unexpected flags
value (no O_RDONLY / O_RDWR / O_WRONLY), an assertion fired, causing panic.
For now, prevent the panic by rejecting such VOP_OPENs with EINVAL.
This is not considered the correct long term fix, but does prevent an
unprivileged denial-of-service.
PR: 236329
Reported by: asomers
Reviewed by: asomers
Sponsored by: Dell EMC Isilon
* The ani function bitmap was being badly used when determining if a command
could be used. In hostap modes only a couple of the ANI control parameters
are enabled.
* The ani function bitmap was not being reset to HAL_ANI_ALL if transitioning
from AP -> STA.
* Change mrcCckOff to mrcCck - 1 == on, rather than 1 == off. This matches
the API used to set the value from userland via the diagnostic API.
* Handle OFDM/CCK noise immunity level commands in ar9300_ani_control().
These will only come from userland and it will go and program the rest of
the ANI control parameters with the values in the ANI table.
* Ensure all of the ANI parameters can be tweaked at runtime, even if they're
disabled.
Tested:
* carambola2 (AR9331), STA/AP modes
This mirrors the arm64 implementation and is for use in the minidump
code.
Submitted by: Mitchell Horne <mhorne063@gmail.com>
Differential Revision: https://reviews.freebsd.org/D18321
Note that only entries wired by userspace are shown as such. In
particular, entries transiently wired by sysctl_wire_old_buffer() are
not flagged as wired in procstat -v output.
Reviewed by: kib (previous version)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19461
From Jake:
"The iflib_fl_setup() function tries to pick various buffer sizes based
on the max_frame_size value defined by the parent driver. However, this
code was wrapped under CONTIGMALLOC_WORKS, which was never actually
defined anywhere.
This same code pattern was used in if_em.c, likely trying to match
what iflib uses.
Since CONTIGMALLOC_WORKS is not defined, remove this dead code from
iflib_fl_setup and if_em.c
Given that various iflib drivers appear to be using a similar
calculation, it might be worth making this buffer size a value that the
driver can peek at in the future."
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed by: shurd@
MFC after: 1 week
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D19199
The if_tun cloner is not virtualised, but if_clone_attach() does use a
virtualised list of cloners.
The result is that we can't find the if_tun cloner when we try to remove
a renamed tun interface. Virtualise the cloner, and move the final
cleanup into a sysuninit so that we're sure this happens after all of
the vnet_sysuninits
Note that we need unit numbers to be system-unique (rather than unique
per vnet, as is done by if_clone_simple()). The unit number is used to
create the corresponding /dev/tunX device node, and this node must match
with the interface.
Switch to if_clone_advanced() so that we have control over the unit
numbers.
Reproduction scenario:
jail -c -n foo persist vnet
jexec test ifconfig tun create
jexec test ifconfig tun0 name wg0
jexec test ifconfig wg0 destroy
PR: 235704
Reviewed by: bz, hrs, hselasky
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19248
In revision 254095, gpt_entries is not set to match the on-disk
hdr_entries, but rather is computed based on available space.
There are 2 problems with this:
1. The GPT backend respects hdr_entries and only reads and writes
that number of partition entries. On top of that, CRC32 is
computed over the table that has hdr_entries elements. When
the common code works on what is possibly a larger number, the
behaviour becomes inconsistent and problematic. In particular,
it would be possible to add a new partition that on a reboot
isn't there anymore.
2. The calculation of gpt_entries is based on flawed assumptions.
The GPT specification does not dictate that sectors are layed
out in a particular way that the available space can be
determined by looking at LBAs. In practice, implementations
do the same thing, because there's no reason to do it any
other way. Still, GPT allows certain freedoms that can be
exploited in some form or shape if the need arises.
PR: 229977
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19438
Mask off the bits we don't care about when checking that capabilities
of the member interfaces have been disabled as intended.
Submitted by: Ryan Moeller <ryan@ixsystems.com>
Reviewed by: kristof, mav
MFC after: 1 week
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D18924
of it being explicitly passed as an argument. No functional changes.
The big picture here is that I want to get rid of the 'td' argument
being passed everywhere, and this is the first piece that affects
the NFS server.
Reviewed by: rmacklem
MFC after: 2 weeks
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D19417
Add more on-disk superblock consistency checks to ext2_compute_sb_data() function.
It should decrease the probability of mounting filesystems with corrupted superblock data.
Reviewed by: pfg
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D19322
I'm trying to debug why reception upstairs here is so terrible and it
turns out ANI is buggy. (Which is no surprise, ANI is always buggy.)
Tested:
* Carambola2 (AR9331), STA/AP modes
- Fix data frames transmission via POWER_STATUS register setup -
it seems to be set by MACID_CONFIG firmware command, which was broken*
in r290439 and later disabled in r307529.
We can re-enable it later if / when firmware rate adaptation will be
ready; however, this step will be required anyway - for firmware-less
builds.
- Force RTS / CTS protection frame rate to CCK1 (this rate works fine
without any additional setup; no better workaround is known yet).
The problem was not observed on the channel 1 or with CCK1 rate enforced
('ifconfig wlan0 ucastrate 1' for 11 b/g; not possible for 11n networks
due to ifconfig(8) bug).
* I'm not sure if it works before r290439 because - AFAIR - I never seen
firmware rate adaptation working for 10-STABLE urtwn(4)
(It needs EN_BCN bit set and RSSI updates at least).
Tested with RTL8188CUS in STA mode
(in regular mode and with disabled MRR - DARFRC*8 is set to 0)
PR: 233949
MFC after: 2 weeks
Since in most configurations CTL serves as network service, we found
that this change improves local system interactivity under heavy load.
Priority of main threads is set slightly higher then worker taskqueues
to make them quickly sort incoming requests not creating bottlenecks,
while plenty of worker taskqueues should be less sensitive to latency.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
to call soabort() on a newborn socket created by sonewconn() in case
if further setup of PCB failed. Code in sofree() handles such socket
correctly.
Submitted by: jtl, rrs
MFC after: 3 weeks
FDT data. The sector size must be a multiple of the device's page size.
If not configured, use the historical default of the device page size.
Setting the disk sector size to 512 or 4096 allows a variety of standard
filesystems to be used on the device. Of course you wouldn't want to be
writing frequently to a SPI flash chip like it was a disk drive, but for
data that gets written once (or rarely) and read often, using a standard
filesystem is a nice convenient thing.
some #define'd names to be more descriptive. When reporting a post-write
compare failure, report the page number, not the byte address of the page.
The latter is the only functional change, it makes the number match the
words of the error message.
This is especially important for writes. SPI is inherently a bidirectional
bus; you receive data (even if it's garbage) while writing. We should not
receive that data into the same buffer we're writing to the device.
When reading it doesn't matter what we send to the device, but using the
dummy buffer for that as well is pleasingly symmetrical.
On very large powerpc64 systems (2x22x4 power9) it's very easy to run out of
available IRQs and crash the system at boot. Scale the count by mp_ncpus,
similar to x86, so this doesn't happen. Further work can be done in the future
to scale the I/O IRQs as well, but that's left for the future.
Submitted by: mmacy
MFC after: 3 weeks
When a vCPU is HLTed, interrupts with a priority below the processor
priority (PPR) should not resume the vCPU while interrupts at or above
the PPR should. With posted interrupts, bhyve maintains a bitmap of
pending interrupts in PIR descriptor along with a single 'pending'
bit. This bit is checked by a CPU running in guest mode at various
places to determine if it should be checked. In addition, another CPU
can force a CPU in guest mode to check for pending interrupts by
sending an IPI to a special IDT vector reserved for this purpose.
bhyve had a bug in that it would only notify a guest vCPU of an
interrupt (e.g. by sending the special IPI or by resuming it if it was
idle due to HLT) if an interrupt arrived that was higher priority than
PPR and no interrupts were currently pending. This assumed that if
the 'pending' bit was set, any needed notification was already in
progress. However, if the first interrupt sent to a HLTed vCPU was
lower priority than PPR and the second was higher than PPR, the first
interrupt would set 'pending' but not notify the vCPU, and the second
interrupt would not notify the vCPU because 'pending' was already set.
To fix this, track the priority of pending interrupts in a separate
per-vCPU bitmask and notify a vCPU anytime an interrupt arrives that
is above PPR and higher than any previously-received interrupt.
This was found and debugged in the bhyve port to SmartOS maintained by
Joyent. Relevant SmartOS bugs with more background:
https://smartos.org/bugview/OS-6829https://smartos.org/bugview/OS-6930https://smartos.org/bugview/OS-7354
Submitted by: Patrick Mooney <pmooney@pfmooney.com>
Reviewed by: tychon, rgrimes
Obtained from: SmartOS / Joyent
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19299
As a step towards adding other potential streaming ciphers. As well as just
pushing the loop down into the rijndael APIs (basically 128-bit wide AES-ICM
mode) to eliminate some excess explicit_bzero().
No functional change intended.
Reviewed by: delphij, markm
Approved by: secteam (delphij)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D19411
level socket option SCTP_GET_LOCAL_ADDRESSES in a getsockopt() call.
Thanks to Thomas Barabosch for reporting the issue which was found by
running syzkaller.
MFC after: 3 days
In all of the architectures we have today, we always use PAGE_SIZE.
While in theory one could define different things, none of the
current architectures do, even the ones that have transitioned from
32-bit to 64-bit like i386 and arm. Some ancient mips binaries on
other systems used 8k instead of 4k, but we don't support running
those and likely never will due to their age and obscurity.
Reviewed by: imp (who also contributed the commit message)
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D19280
When porting code once written for Linux we find not only uints but also ushort and ulong.
Provide central typedefs as part of the linuxkpi for those as well.
Reviewed by: hselasky, emaste
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19405
The plls frequency are now correctly calculated in fractional mode
and integer mode.
While here add some debug printfs (disabled by default)
Tested with powerd on the little cluster on a RockPro64.
MFC after: 1 week
We mistakenly used the extoff value from the last packet to patch the
next_header field. If a malicious host sends a chain of fragmented packets
where the first packet and the final packet have different lengths or number of
extension headers we'd patch the next_header at the wrong offset.
This can potentially lead to panics or rule bypasses.
Security: CVE-2019-5597
Obtained from: OpenBSD
Reported by: Corentin Bayet, Nicolas Collignon, Luca Moro at Synacktiv
Firmware needed by petitboot, for example, GPU firmware, can be installed to
a partition in the flash filesystem. This driver exposes the full flash
given by the device tree, letting the user manage firmware, etc, from
FreeBSD.
To use the partitions provided by the flash module, the fdt_slicer module is
needed, but the module isn't needed for raw access, so there's no direct
dependency link in here.
MFC after: 2 weeks
For some reason this seems to be required on aarch64, but I can build armv7
from clean without needing this in the list. (The file does get included,
so the mystery is why armv7 works.)
The OPAL firmware only supports a finite number of in-flight asynchronous
operations. Rather than have each subsystem try to manage its own, use a
central management service to hand out tokens.
More work can be done to improve asynchronous behavior, such as funneling
things through a future OPAL heartbeat handler, but capabilities will be
added as needed.
Augment the existing consumers (i2c and sensors) to use this new API.
MFC after: 4 weeks
SGE_QSETS is an upper bound -- fewer qsets may be allocated depending on
the number of CPUs.
Reviewed by: markj, np, vangyzen
X-MFC-With: r333288
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D17274
When the device is in attaching state, detach should return
EBUSY instead of success. In other case, there could be race
between attach and detach during the driver unloading.
If driver goes sleep and releases GIANT lock during attaching,
unloading module could start. In such case when attach continues
after module unload, page fault "supervisor read instruction,
page not present" occurred.
This patch works around the real issue, which is a locking
deficiency of the busses.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: imp
Obtained from: Semihalf
MFC after: 2 weeks
Sponsored by: Amazon, Inc.
Differential Revision: https://reviews.freebsd.org/D19375
geom_flashmap depends on a slicer being available in order to do any
work. On fdt platforms this is provided by fdt_slicer, but this needs
to be available. Often it's compiled into the kernel for platforms that
boot from the relevant media, but this is not always the case. Add the
file to the geom_flashmap module so that it can be used on platforms
which don't always need this functionality available.
Specifically, ccr(4) devices are also children of cxgbe nexus devices.
Rather than making assumptions about the child device's softc, walk
the list of ports from the nexus' softc to determine if a child is a
port in t4_child_location_str(). This fixes a panic when detaching a
ccr device.
Reviewed by: np
MFC after: 1 week
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D19399
They have no effect, as with filesystem file descriptors.
This improves compatibility with some existing userspace code.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D19330
This was actually the known good configuration we used before.
Single MSI-X configuration doesn't even work there on my tests, just due
to lack of documentation not sure whether by design or I am doing something
wrong.
PR: 233654
MFC after: 1 week
not supported.
According to SDM rev. 69 vol. 3, for PDPTE registers loads:
- when PAT is not supported, access to the PDPTE page is performed as
UC, see 4.9.1;
- when PAT is supported, the access is WB, see 4.9.2.
So potentially CPU might load stale memory as PDPTEs if both PAT and
self-snoop are not implemented. To be safe, add total local cache
flush to pmap_cold() before initial load of cr3, and flush PDPTE page
in pmap_pinit(), if PAT is not implemented.
Reviewed by: markj
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D19365
@cem removed references to pdwait4(2) (a nonexistent syscall) in
r320058.
This change removes references to pdwait4(2) and `CAP_PDWAIT` in
rights(4) to not mislead the user into thinking that pdwait4(2)/`CAP_PDWAIT` is
actually implemented in the stock FreeBSD kernel.
The goal of this functionality was to simplify monitoring/manipulating
processes started with `pdfork`, et al, and avoid races with waiting on pids.
The syscall was never completed though--just discussed on the capsicum mailing
list back in 2015:
https://lists.cam.ac.uk/pipermail/cl-capsicum-discuss/2015-May/msg00012.html
. That being said, there are members of the project (@rwatson, etc) who
have longterm goals to implement this syscall to better secure pdfork(2)
calls.
PR: 235871
Reviewed by: emaste
Discussed with: rwatson
Approved by: emaste (mentor)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D18950
These are 4Gb/s and pretty old and slow now, so I see no reason to fight
for their performance over stability.
PR: 233654
MFC after: 1 week
Sponsored by: iXsystems, Inc.
There are some problem reports possibly related to the new driver use of
multiple interrupts on older cards. Hopefully this allow to workaround
them.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
This allows us to limit the number of CPUs to use, e.g. to debug problems
seen when enabling multiple clusters.
Reviewed by: manu
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D19404
Linux generates the content of procfs files using a mechanism prefixed with
seq_*. This in particular came up with recent gcov import.
Sponsored by: The FreeBSD Foundation
r344162 exposed a bug in one of ixgbe's interrupt filters; they are never
supposed to return 0. Fix the interrupt filter to return the proper nonzero
return value.
Reported by: Oleg Ginzburg <olevole@olevole.ru>
MFC after: 1 week
Sponsored by: Intel Corporation
supporting older kernels. However, all supported versions of FreeBSD
have unmapped I/Os (as do several that have gone EOL), remove it. It's
unlikely the driver would work on the older kernels anyway at this
point.
supported in years. A number of changes have been made to the driver
that likely wouldn't work on those older versions that aren't properly
ifdef'd and it's project policy to GC such code once it is stale.
Replace long per-LUN queue of blocked commands, scanned on each command
completion and sometimes even twice, causing up to O(n^^2) processing cost,
by much shorter per-command blocked queues, scanned only when respective
command completes, and check only commands before the previous blocker,
reducing cost to O(n).
While there, unblock aborted commands to make them "complete" ASAP to be
removed from the OOA queue and so not waste time ordering other commands
against them. Aborted commands that were not sent to execution yet should
have no visible side effects, so this is safe and easy optimization now,
comparing to commands already in processing, which are a still pain.
Together those two optimizations should fix quite pathological case, when
due to backend slowness CTL accumulated many thousands of blocked requests,
partially aborted by initiator and so supposedly not even existing, but
still wasting CTL CPU time.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Marvell XHCI is in fact generic-xhci, so move the driver and
add the compatible string.
While here, get and enable the phy if the dtb provide one.
The xhci bindings state that phys should be in a 'phys' property but
Marvell DTS uses 'usb-phy', only add support for 'usb-phy' for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
This is a "fake" phy that handle regulator, clocks and reset gpio.
Only clock and regulator is supported for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
- Use strlcpy() with sizeof() instead of strncpy().
- Simplify initialization of TCP functions structures.
init_tcp_functions() was already called before the first call to
register a stack. Just inline the work in the SYSINIT and remove
the racy helper variable. Instead, KASSERT that the rw lock is
initialized when registering a stack.
- Protect the default stack via a direct pointer comparison.
The default stack uses the name "freebsd" instead of "default" so
this protection wasn't working for the default stack anyway.
Reviewed by: rrs
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D19152
This is the common denominator for rockchip compatible from RK3288 to RK3399.
The other compatible are generally present in the DTS but the controllers
are the same.
MFC after: 1 week
Remove the mode_val from the clock definition as it's a bit unreadable.
Use mode_shift to represent which bit control the mode in the register.
Simplify some case where we can avoid a register read before changing it.
Set the PLL back to normal mode after the PLL have stabilized.
Discussed with: mmel
MFC after: 1 week
devicetree/bindings/mtd/partition.txt.
In the old style, all the children of the device node which did not have a
compatible property were the partitions. In the new style, there is a child
node of the device which has a compatible string of "fixed-partitions", and
its children are the individual partitions.
Also, support the read-only property by setting the corresponding slice flag.
unwrapping multiple lines of code. Also, convert some short multiline
comments into single-line comments. Change old-school FALSE to false.
All in all, no functional changes, it's just more compact and readable.
Summary:
To safely synchronize timebase we need to disable the timebase on all
cores, set timebase, and resynchronize. This adds two new devices, mutually
exclusive, which attach on the SoC simplebus, to freeze and unfreeze the
timebase. The devices are singletons, and platform-specific, so no reason
to make them optional and in separate files.
This was found to be necessary for top(1) to work correctly on an AmigaOne
X5000 (P5020 SoC). It also fixes bufdaemon and bufspacedaemon hangs at
shutdown.
Test Plan: Regression test on various Book-E hardware.
Reviewed by: nwhitehorn
Tested by: Brandon Bergren (git_bdragon.rtk0.net)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19208
Embedded lzma decompression library becomes a module usable by other
consumers, in addition to geom_uzip.
Most important code changes are
- removal of XZ_DEC_SINGLE define, we need the code to work
with XZ_DEC_DYNALLOC;
- xz_crc32_init() call is removed from geom_uzip, xz module handles
initialization on its own.
xz is no longer embedded into geom_uzip, instead the depend line for
the module is provided, and corresponding kernel option is added to
each MIPS kernel config file using geom_uzip.
The commit also carries unrelated cleanup by removing excess "device geom_uzip"
in places which were missed in r344479.
Reviewed by: cem, hselasky, ray, slavash (previous versions)
Sponsored by: Mellanox Technologies
Differential revision: https://reviews.freebsd.org/D19266
MFC after: 3 weeks
- Don't leak the ksiginfo structure.
- Hold the proc lock when sending a signal in fasttrap_sigsegv().
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
The file has not been touched upstream in over a decade, and the nature
of the code means that a lot of FreeBSD-specific bits are required. Remove
the dead code to improve readability. No functional change intended.
Discussed with: cem
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
No platforms except i386, amd64 and powerpc implement fasttrap; the
fasttrap files for other arches do not contain any code and bloat
the output from cscope, so just remove them.
MFC after: 1 week
No map function was provided before so every regulator lookup resolved
the regulator with id 1, as it uses the default mapper, which is wrong.
Correctly map the regulators.
While here remove some debug printfs and make them disable by default.
MFC after: 1 week
RockChip clocks register have a write mask in the upper 16 bits, if a 1
is present the corresponding bit in the lower 16 ones is set.
Use this instead of always setting the mask to 0xFFFF0000.
This avoids a read of the register.
While here, when switching PLL frequency, first switch it to slow mode.
When set to slow mode the PLL clock will be the external oscillator.
Changing the PLL parameters while its output is used can cause hang (sometimes).
MFC after: 1 week
RockChip clocks register have a write mask in the upper 16 bits, if a 1
is present the corresponding bit in the lower 16 ones is set.
Use this instead of always setting the mask to 0xFFFF0000.
This avoids a read of the register.
While here set the parent after changing its freqeuncy, this reduce the time
between changing the parent and changing the divider for the arm clock.
MFC after: 1 week
RockChip clocks register have a write mask in the upper 16 bits, if a 1
is present the corresponding bit in the lower 16 ones is set.
Use this instead of always setting the mask to 0xFFFF0000.
This avoids a read of the register.
While here add some debug printf useful for debuging clock problems
MFC after: 1 week
Instead carefully write upper word, and only than the lower word with
PG_V, for previously invalid ptes. It provides some measurable system
time saving on buildworld.
Reviewed by: markj
Tested by: pho
Measured by: bde (early version)
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D19226
Non-x86 arches use an inconsistently named header for the file containing
"pc" attributes, and the ifdef messes to include the right header were out
of date in the 2 files that I added to the MI files list.
Only amd64, arm, i386, mips, powerpc and sparc64 are supposed to support
syscons. Only arm and mips were out of date in the ifdef. Test
coverage for of syscons in arm is broken (turned off) in NOTES, but
syscons is in some other arm config files which universe detects as broken.
arm64 and riscv remain broken due to the opposite bug of not turning off
sc in NOTES, the same as before r344458 (see r344443).
The header is MD to contain possibly-non-"pc" encodings of attributes, but
since the attributes are essentially virtual in graphics mode and non-x86
arches only support graphics mode, the header has always been the same on
all arches except for different style bugs, so there should be only 1 MI
copy of it for syscons' use. It was used in pcvt and still gives an an
API and an ABI, so it should be public and MI near or in sys/consio.h.
Implement ffs_getpages_async(), which when possible calls the asynchronous
flavor of the generic pager's getpages function. When the underlying
block size is larger than the system page size, however, it will invoke
the (synchronous) buffer cache pager, followed by a call to the client
completion routine. This retains true asynchronous completion in the most
common (block size <= page size) case, which is important for the performance
of the new sendfile(2). The behavior in the larger block size case mirrors
the default implementation of VOP_GETPAGES_ASYNC, which most other
filesystems use anyway as they do not override the getpages_async method.
PR: 235708
Reported by: pho
Reviewed by: kib, glebius
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19340
shorter than its size resulting in a hole as its final block (which
is a violation of the invarients of the UFS filesystem).
Soft updates will always ensure that the file size is correct when
writing inodes to disk for files that contain only direct block
pointers. However soft updates does not roll back sizes for files
with indirect blocks that it has set to unallocated because their
contents have not yet been written to disk. Hence, the file can
appear to have a hole at its end because the block pointer has been
rolled back to zero when its inode was written to disk. Thus,
fsck_ffs calculates the last allocated block in the file. For files
that extend into indirect blocks, fsck_ffs checks for a size past
the last allocated block of the file and if that is found, shortens
the file to reference the last allocated block thus avoiding having
it reference a hole at its end.
Submitted by: Chuck Silvers <chs@netflix.com>
Tested by: Chuck Silvers <chs@netflix.com>
MFC after: 1 week
Sponsored by: Netflix
On platforms without a direct map (i.e., platforms without
UMA_MD_SMALL_ALLOC defined), the boundary tag allocator reserves a
number of tags for use when allocating a new slab of boundary tags,
as such platforms require free boundary tags in order to allocate
boundary tags. r327899 increased the number of boundary tags required
for a KVA allocation in the worst case, and the aforementioned
reservation was not updated accordingly. In some cases, this could
lead to a system hang. Fix the problem by increasing this reservation.
Also reduce KVA_QUANTUM on systems lacking superpage support.
The previous import quantum (4MB with a 4KB page size) was quite large
for systems with limited KVA, and fragmentation in kernel_arena could
cause kernel memory allocation failures even with a substantial amount
of free KVA.
Reported and tested by: jhibbits
Reviewed by: alc, kib
No objections: jeff
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19337
the tag wasn't being computed properly due to chaning a >= comparison
to an == comparison.
Specifically: CBC-MAC encodes the length of the authorization data
into the the stream to be encrypted/hashed. For short data, this is
two bytes (big-endian 16 bit value); for larger data, it's 6 bytes
(a prefix of 0xff, 0xfe, followed by a 32-bit big-endian length). And
there's a larger size, which is 10 bytes. These extra bytes weren't
being accounted for with the post-review code. The other bit that then came
into play was that OCF only calls the Update code with blksiz=16, which
meant that I had to ignore the length variable. (It also means that it
can't be called with a single buffer containing the AAD and payload;
however, OCF doesn't do this for the software-only algorithsm.)
I tested with this script:
ALG=aes-ccm
DEV=soft
for aad in 0 1 2 3 4 14 16 24 30 32 34 36 1020
do
for dln in 16 32 1024 2048 10240
do
echo "Testing AAD length ${aad} data length ${dln}"
/root/cryptocheck -A ${aad} -a ${ALG} -d ${DEV} ${dln}
done
done
Reviewed by: cem
Sponsored by: iXsystems Inc.
Instead of PRIVATELIB + NO_PIC. This avoids the need for the wlandebug
PIE special case added in r344211, and provides a stronger guarantee
against 3rd party software coming to depend on the API or ABI.
If / when we declare the API/ABI to be stable we can make it a normal
library.
Discussed with: bapt
Sponsored by: The FreeBSD Foundation
RockChip clocks have a write mask in the upper 16bits of the mux register
which wasn't set in the set_mux function.
Also the wrong parent was tested instead of the real current one, when
switch parent, test with the current one before.
Pointy Hat: manu
MFC after: 1 week
Both SpiFlash (mx25l) and DataFlash (at45d) drivers create a disk device
with a name of /dev/flash/spiN where N is the driver's unit number. If
both types of devices are present in the same system, this creates a fatal
conflict that prevents attachment of whichever device attaches second
(because mx25l0 and at45d0 both try to create a spi0).
This gives each type of device a unique name (mx25lN or at45dN respectively)
and also adds an alias of spiN for compatibility. When both device types
appear in the same system, only the first to attach gets the spiN alias.
When the second device attaches there is a non-fatal warning that the alias
can't be created, but both devices are still accessible via their primary
names (and there is no need for the spiN name to work for backwards
compatibility on such a system, because it has never been possible to use
the spiN names when both devices exist).
jedec ID as its older cousin the AT45DB642D, but uses a different page size.
The only way to distinguish between the two chips is that the 2D chip has
0 bytes of extended ID info and the new 1E has 1 byte of extended ID. The
actual value of the extended ID byte is all zeroes. In other words, it's
the presence of the extended info that identifies this chip. (Presumably
a future upgrade might define non-zero values for the extended ID byte.)