The ccr(4) driver supports use of the crypto accelerator engine on
Chelsio T6 NICs in "lookaside" mode via the opencrypto framework.
Currently, the driver supports AES-CBC, AES-CTR, AES-GCM, and AES-XTS
cipher algorithms as well as the SHA1-HMAC, SHA2-256-HMAC, SHA2-384-HMAC,
and SHA2-512-HMAC authentication algorithms. The driver also supports
chaining one of AES-CBC, AES-CTR, or AES-XTS with an authentication
algorithm for encrypt-then-authenticate operations.
Note that this driver is still under active development and testing and
may not yet be ready for production use. It does pass the tests in
tests/sys/opencrypto with the exception that the AES-GCM implementation
in the driver does not yet support requests with a zero byte payload.
To use this driver currently, the "uwire" configuration must be used
along with explicitly enabling support for lookaside crypto capabilities
in the cxgbe(4) driver. These can be done by setting the following
tunables before loading the cxgbe(4) driver:
hw.cxgbe.config_file=uwire
hw.cxgbe.cryptocaps_allowed=-1
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D10763
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Reviewed by: np
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7599
in lockstat.ko. This means that lockstat probes now have typed arguments and
will utilize SDT probe hot-patching support when it arrives.
Reviewed by: gnn
Differential Revision: https://reviews.freebsd.org/D2993
This will require for AArch64 as we dont have modules yet.
Sponsored by: HEIF5
Sponsored by: ARM Ltd.
Differential Revision: https://reviews.freebsd.org/D1997
This port failed to gain traction and probably only a couple Wii consoles
ran FreeBSD all the way to single user mode with an md(4). IPC
support was never implemented, so it was impossible to use any peripheral
Any further development, if any, will happen at https://github.com/rpaulo/wii.
Discussed with: nathanw (a long time ago), jhibbits
For compatibility, 'device windtunnel' is still supported, but one should use
'device adm1030' instead, and this has been updated in GENERIC and NOTES.
implementation specific vs. the common architecture definition.
Bring PPC4XX defines (PSL, SPR, TLB). Note the new definitions under
BOOKE_PPC4XX are not used in the code yet.
This change set is not supposed to affect existing E500 support, it's just
another reorg step before bringing support for E500mc, E5500 and PPC465.
Obtained from: AppliedMicro, Freescale, Semihalf
available on firmwares 3.15 and earlier.
Caveats: Support for the internal SATA controller is currently missing,
as is support for framebuffer resolutions other than 720x480. These
deficiencies will be remedied soon.
Special thanks to Peter Grehan for providing the hardware that made this
port possible, and thanks to Geoff Levand of Sony Computer Entertainment
for advice on the LV1 hypervisor.
PowerMac7,2.
- The fcu driver lets us read and write the fan RPMs for all fans in the
PowerMac7,2. This driver is PowerMac specific.
- The ds1775 is a driver to read the temperature for the drive bay sensor.
- The max6690 is another driver to read temperatures. Here it is used to
read the inlet, the backside and the U3 heatsink temperature.
An additional driver, the ad7417, will follow later.
Thanks to nwhitehorn for guiding me through this driver development.
Approved by: nwhitehorn (mentor)
Kernel sources for 64-bit PowerPC, along with build-system changes to keep
32-bit kernels compiling (build system changes for 64-bit kernels are
coming later). Existing 32-bit PowerPC kernel configurations must be
updated after this change to specify their architecture.
power and thermal control, as well as GPIOs on Xserves and controlling
sound codecs for Apple built-in audio.
Submitted by: Marco Trillo
Obtained from: NetBSD
The kernel config file is KERNCONF=MPC85XX, so the usual procedure applies:
1. make buildworld TARGET_ARCH=powerpc
2. make buildkernel TARGET_ARCH=powerpc TARGET_CPUTYPE=e500 KERNCONF=MPC85XX
This default config uses kernel-level FPU emulation. For the soft-float world
approach:
1. make buildworld TARGET_ARCH=powerpc TARGET_CPUTYPE=e500
2. disable FPU_EMU option in sys/powerpc/conf/MPC85XX
3. make buildkernel TARGET_ARCH=powerpc TARGET_CPUTYPE=e500 KERNCONF=MPC85XX
Approved by: cognet (mentor)
MFp4: e500
a pointer to struct bus_space. The structure contains function
pointers that do the actual bus space access.
The reason for this change is that previously all bus space
accesses were little endian (i.e. had an explicit byte-swap
for multi-byte accesses), because all busses on Macs are little
endian.
The upcoming support for Book E, and in particular the E500
core, requires support for big-endian busses because all
embedded peripherals are in the native byte-order.
With this change, there's no distinction between I/O port
space and memory mapped I/O. PowerPC doesn't have I/O port
space. Busses assign tags based on the byte-order only.
For that purpose, two global structures exist (bs_be_tag and
bs_le_tag), of which the address can be taken to get a valid
tag.
Obtained from: Juniper, Semihalf
processors (it's the PowerPC Operating Environment Architecture).
AIM designates the processors made by the Apple-IBM-Motorola
alliance and those we typically support.
While here, remove the NetBSD option IPKDB. It's not an option
used by us. Also, PPC_HAVE_FPU is not used by us either. Remove
that too.
Obtained from: Juniper, Semihalf
to gem_attach() as the former access softc members not yet initialized
at that time and gem_reset() actually is enough to stop the chip. [1]
o Revise the use of gem_bitwait(); add bus_barrier() calls before calling
gem_bitwait() to ensure the respective bit has been written before we
starting polling on it and poll for the right bits to change, f.e. even
though we only reset RX we have to actually wait for both GEM_RESET_RX
and GEM_RESET_TX to clear. Add some additional gem_bitwait() calls in
places we've been missing them according to the GEM documentation.
Along with this some excessive DELAYs, which probably only were added
because of bugs in gem_bitwait() and its use in the first place, as
well as as have of an gem_bitwait() reimplementation in gem_reset_tx()
were removed.
o Add gem_reset_rxdma() and use it to deal with GEM_MAC_RX_OVERFLOW errors
more gracefully as unlike gem_init_locked() it resets the RX DMA engine
only, causing no link loss and the FIFOs not to be cleared. Also use it
deal with GEM_INTR_RX_TAG_ERR errors, with previously were unhandled.
This was based on information obtained from the Linux GEM and OpenSolaris
ERI drivers.
o Turn on workarounds for silicon bugs in the Apple GMAC variants.
This was based on information obtained from the Darwin GMAC and Linux GEM
drivers.
o Turn on "infinite" (i.e. maximum 31 * 64 bytes in length) DMA bursts.
This greatly improves especially RX performance.
o Optimize the RX path, this consists of:
- kicking the receiver as soon as we've a spare descriptor in gem_rint()
again instead of just once after all the ready ones have been handled;
- kicking the receiver the right way, i.e. as outlined in the GEM
documentation in batches of 4 and by pointing it to the descriptor
after the last valid one;
- calling gem_rint() before gem_tint() in gem_intr() as gem_tint() may
take quite a while;
- doubling the size of the RX ring to 256 descriptors.
Overall the RX performance of a GEM in a 1GHz Sun Fire V210 was improved
from ~100Mbit/s to ~850Mbit/s.
o In gem_add_rxbuf() don't assign the newly allocated mbuf to rxs_mbuf
before calling bus_dmamap_load_mbuf_sg(), if bus_dmamap_load_mbuf_sg()
fails we'll free the newly allocated mbuf, unable to recycle the
previous one but a NULL pointer dereference instead.
o In gem_init_locked() honor the return value of gem_meminit().
o Simplify gem_ringsize() and dont' return garbage in the default case.
Based on OpenBSD.
o Don't turn on MAC control, MIF and PCS interrupts unless GEM_DEBUG is
defined as we don't need/use these interrupts for operation.
o In gem_start_locked() sync the DMA maps of the descriptor rings before
every kick of the transmitter and not just once after enqueuing all
packets as the NIC might instantly start transmitting after we kicked
it the first time.
o Keep state of the link state and use it to enable or disable the MAC
in gem_mii_statchg() accordingly as well as to return early from
gem_start_locked() in case the link is down. [3]
o Initialize the maximum frame size to a sane value.
o In gem_mii_statchg() enable carrier extension if appropriate.
o Increment if_ierrors in case of an GEM_MAC_RX_OVERFLOW error and in
gem_eint(). [3]
o Handle IFF_ALLMULTI correctly; don't set it if we've turned promiscuous
group mode on and don't clear the flag if we've disabled promiscuous
group mode (these were mostly NOPs though). [2]
o Let gem_eint() also report GEM_INTR_PERR errors.
o Move setting sc_variant from gem_pci_probe() to gem_pci_attach() as
device probe methods are not supposed to touch the softc.
o Collapse sc_inited and sc_pci into bits for sc_flags.
o Add CTASSERTs ensuring that GEM_NRXDESC and GEM_NTXDESC are set to
legal values.
o Correctly set up for 802.3x flow control, though #ifdef out the code
that actually enables it as this needs more testing and mainly a proper
framework to support it.
o Correct and add some conversions from hard-coded functions names to
__func__ which were borked or forgotten in if_gem.c rev. 1.42.
o Use PCIR_BAR instead of a homegrown macro.
o Replace sc_enaddr[6] with sc_enaddr[ETHER_ADDR_LEN].
o In gem_pci_attach() in case attaching fails release the resources in
the opposite order they were allocated.
o Make gem_reset() static to if_gem.c as it's not needed outside that
module.
o Remove the GEM_GIGABIT flag and the associated code; GEM_GIGABIT was
never set and the associated code was in the wrong place.
o Remove sc_mif_config; it was only used to cache the contents of the
respective register within gem_attach().
o Remove the #ifdef'ed out NetBSD/OpenBSD code for establishing a suspend
hook as it will never be used on FreeBSD.
o Also probe Apple Intrepid 2 GMAC and Apple Shasta GMAC, add support for
Apple K2 GMAC. Based on OpenBSD.
o Add support for Sun GBE/P cards, or in other words actually add support
for cards based on GEM to gem(4). This mainly consists of adding support
for the TBI of these chips. Along with this the PHY selection code was
rewritten to hardcode the PHY number for certain configurations as for
example the PHY of the on-board ERI of Blade 1000 shows up twice causing
no link as the second incarnation is isolated.
These changes were ported from OpenBSD with some additional improvements
and modulo some bugs.
o Add code to if_gem_pci.c allowing to read the MAC-address from the VPD on
systems without Open Firmware.
This is an improved version of my variant of the respective code in
if_hme_pci.c
o Now that gem(4) is MI enable it for all archs.
Pointed out by: yongari [1]
Suggested by: rwatson [2], yongari [3]
Tested on: i386 (GEM), powerpc (GMACs by marcel and yongari),
sparc64 (ERI and GEM)
Reviewed by: yongari
Approved by: re (kensmith)
NOTES though, as ofw_syscons(4) doesn't properly interface with
syscons(4) regarding loading the font specified with SC_DFLT_FONT,
causing a kernel with both options SC_OFWFB and SC_NO_MODE_CHANGE
to not link.
and pc98 MD files. Remove nodevice and nooption lines specific
to sio(4) from ia64, powerpc and sparc64 NOTES. There were no
such lines for arm yet.
sio(4) is usable on less than half the platforms, not counting
a future mips platform. Its presence in MI files is therefore
increasingly becoming a burden.
