the queue where to enqueue pages that are going to be unwired.
- Add stronger checks to the enqueue/dequeue for the pagequeues when
adding and removing pages to them.
Of course, for unmanaged pages the queue parameter of vm_page_unwire() will
be ignored, just as the active parameter today.
This makes adding new pagequeues quicker.
This change effectively modifies the KPI. __FreeBSD_version will be,
however, bumped just when the full cache of free pages will be
evicted.
Sponsored by: EMC / Isilon storage division
Reviewed by: alc
Tested by: pho
portsnap extract, where previously it would panic.. clearly someone
who knows pmap should optimize this code per alc's comment...
Submitted by: alc
MFC after: probably
In particular, don't check the value of the bus_dma map against NULL
to determine if either bus_dmamem_alloc() or bus_dmamap_load() succeeded.
Instead, assume that bus_dmamap_load() succeeeded (and thus that
bus_dmamap_unload() should be called) if the bus address for a resource
is non-zero, and assume that bus_dmamem_alloc() succeeded (and thus
that bus_dmamem_free() should be called) if the virtual address for a
resource is not NULL.
In many cases these bugs could result in leaks when a driver was detached.
Reviewed by: yongari
MFC after: 2 weeks
don't create a map before calling bus_dmamem_alloc() (such maps were
leaked). It is believed that the extra destroy of the map was generally
harmless since bus_dmamem_alloc() often uses special maps for which
bus_dmamap_destroy() is a no-op (e.g. on x86).
Reviewed by: scottl
a partially populated reservation becomes fully populated, and decrease this
field when a fully populated reservation becomes partially populated.
Use this field to simplify the implementation of pmap_enter_object() on
amd64, arm, and i386.
On all architectures where we support superpages, the cost of creating a
superpage mapping is roughly the same as creating a base page mapping. For
example, both kinds of mappings entail the creation of a single PTE and PV
entry. With this in mind, use the page size field to make the
implementation of vm_map_pmap_enter(..., MAP_PREFAULT_PARTIAL) a little
smarter. Previously, if MAP_PREFAULT_PARTIAL was specified to
vm_map_pmap_enter(), that function would only map base pages. Now, it will
create up to 96 base page or superpage mappings.
Reviewed by: kib
Sponsored by: EMC / Isilon Storage Division
SoC's registers base address may differ between boards
(0xf1000000 or 0xd0000000). Therefore, in order to use
the proper CPU Boot Address Redirect register during SMP
initialization in mptramp the real, physical address has
to be passed to mptramp based on the value from DT.
Reviewed by: gber
During Armada's platform_mp_start_ap(), mptramp code
is being copied to the specific physical location (0xffff0000).
Before r265694 the address to which the code should be copied
was equal to the address of mpentry routine that followed the
mptramp in locore.S. Now the mptramp end address should be
exported and used as a copy limit.
Reviewed by: gber
(7-bit device address << 1), always leaving the room for the read/write bit.
This commit convert ti_i2c and revert r259127 on bcm2835_bsc to make them
compatible with 8-bit addresses. Previous to this commit an i2c device
would have different addresses depending on the controller it was attached
to (by example, when compared to any iicbb(4) based i2c controller), which
was a pretty annoying behavior.
Also, update the PMIC i2c address on beaglebone* DTS files to match the new
address scheme.
Now the userland utilities need to do the correct slave address shifting
(but it is going to work with any i2c controller on the system).
Discussed with: ian
MFC after: 2 weeks
The ti_i2c controller only works in the master mode and the i2c address
passed on iicbus_reset() is used to set the controller slave address when
operating as an i2c slave (which isn't currently supported).
When talking to a slave, the slave address is correctly provided to
ti_i2c_tranfer().
through a voltage divisor (R163 and R164 on page 4 of BBB schematic).
Add a note about this on ti_adc(4) man page. The ti_adc(4) man page will
first appear on 10.1-RELEASE.
MFC after: 1 week
Suggested by: Sulev-Madis Silber (ketas)
Manual page reviewed by: brueffer (D127)
and the actual PWM frequency.
Enforce the maximum value for the period sysctl.
The frequency systcl now allows the direct setting of the PWM frequency (it
will try to find the better clkdiv and period for a given frequency, i.e.
the ones that will give the better PWM resolution).
This allows the use lower frequencies on the PWM. Without changing the
clock prescaler the minimum PWM frequency was 1.52kHz.
PWM frequencies checked with an osciloscope.
PWM output tested with some R/C servos at 50Hz.
o Allow setting keymap in FDT, use hardcoded one by default
o Represent fallback keymap as a list rather than directly usable M*N array
Submitted by: Maxim Ignatenko <gelraen.ua@gmail.com>
current RADXA config. Radxa Rock (RR) boards have few types such as
RR (full version), RR Lite and some variants of RR engineering samples.
Add kernel config and FDT file for RR Lite board.
Approved by: stas (mentor)
(XScale mainly) expects the memory located before the kernel to be mapped,
and use it to allocate the page tables, the various stacks, etc.
A better fix would probably be to rewrite the various bla_machdep.c to stop
using that RAM, but I'm not so inclined to do it, especially since I don't
have hardware for all of them.
Use armv7_setttb that sets proper PT attributes.
Get rid of unused CPU functions, put nullop instead.
Exchange obsolete pj4b_/arm11_ functions to the appropriate armv7_ ones.
memory ordering model allows writes to different devices to complete out
of order, leading to a situation where the write that clears an interrupt
source at a device can complete after a write that unmasks and EOIs the
interrupt at the interrupt controller, leading to a spurious re-interrupt.
This adds a generic barrier function specific to the needs of interrupt
controllers, and calls that function from the GIC and TI AINTC controllers.
There may still be other soc-specific controllers that need to make the call.
Reviewed by: cognet, Svatopluk Kraus <onwahe@gmail.com>
MFC after: 3 days
shared flag is set on normal-memory mappings made via pmap_kenter() for SMP.
The "shared flag" part of this change isn't obvious from the diff, here's
the deal... by using the array of preformatted page table entry templates
instead of constructing the PTE from scratch, we automatically get the
right attribute bits set for both caching and shared.
MFC after: 1 week
platform code, it is expected these will be merged in the future when the
ARM code is more complete.
Until more boards can be tested only use this with the Raspberry Pi and
rrename the functions on the other SoCs.
Reviewed by: ian@
Here, "suitably endowed" means that the System Control Coprocessor
(#15) has Performance Monitoring Registers, including a CCNT (Cycle
Count) register.
The CCNT register is used in a way similar to the TSC register in
x86 processors by the get_cyclecount(9) function. The entropy-harvesting
thread is a heavy user of this function, and will benefit from not
having to call binuptime(9) instead.
One problem with the CCNT register is that it is 32-bit only, so
the upper 32-bits of the returned number are always 0. The entropy
harvester does not care, but in case any one else does, follow-up
work may include an interrup trap to increment an upper-32-bit
counter on CCNT overflow.
Another problem is that the CCNT register is not readable in user-mode
code; in can be made readable by userland, but then it is also
writable, and so is a good chunk of the PMU system. For that reason,
the CCNT is not enabled for user-mode access in this commit.
Like the x86, there is one CCNT per core, so they don't all run in
perfect sync.
Reviewed by: ian@ (an earlier version)
Tested by: ian@ (same earlier version)
Committed from: WANDBOARD-QUAD
that and the need to be in a critical section when switching to idleclock
mode for event timers, use spinlock_enter()/exit() to achieve both needs.
The ARM WFI (wait for interrupt) instruction blocks until an interrupt is
asserted, and it will unblock even if interrupts are masked, and it will
unblock immediately if an interrupt is already pending. It is necessary
to execute it with interrupts disabled, otherwise the interrupt that
should unblock it may occur and be serviced just prior to executing the
instruction. At that point the system is inappropriately asleep until
the next timer tick or some other random interrupt happens.
In general, interrupts need to be disabled continuously from the time the
decision is made that there is no work to be done and sleeping is needed
until actually going to sleep, to avoid a race where handling a new
interrupt changes the basis for deciding there is no work to be done.
Submitted by: hps@ (in slightly different form)
On modern ARM SoCs the L2 cache controller sits between the CPU and the
AXI bus, and most on-chip memory-mapped devices are on the AXI bus. We
map the device registers using the 'Device' memory attribute, which means
the memory is not cached, but writes to it are buffered. Ensuring that a
write has made it all the way to a device may require that the L2
controller take some action.
There is currently only one implementation of the new function, for the
PL310 cache controller. It invokes a function that the controller
manual calls "cache sync" but it actually has nothing to do with cache at
all, it triggers a drain of all pending store buffer writes and it blocks
until they complete.
The sheeva and xscale L2 controllers (which predate the concept of Device
memory) don't seem to have a corresponding function. It appears that the
standard armv5 drain_writebuf function includes draining all the way
through the L2 controller.
On armv4 these are defined as synonyms right now, but it's a bit ambiguous
what NOCACHE means (is buffering/write-combining also enabled or not?); this
is a first step towards replacing PTE_NOCACHE with a less ambiguous name.
Remove some other ifdefs that came in with a copy/paste that mean basically
"if this processor supports multicore stuff", because if you're starting up
an AP core... it does.
case where the controller is already enabled.
Some of the pl310 configuration registers cannot be changed while the
controller is active, so if there is any platform-specific init to be done
it must happen before enabling the controller.
The controller should not be enabled upon entry to the kernel, but u-boot
has recently developed the bad habit of leaving caches enabled when
launching the kernel, and since we have no control over that source code
we have to do our best to cope with it. The PL310 manual doesn't document
a safe sequence for disabling the controller, but the sequence used here
(force write-through mode and disable linefill allocations, then clean and
invalidate the current contents before disabling the hardware) appears to
be sound both by analysis and empirical testing.
These changes were developed and tested in collaboration with
Svatopluk Kraus <onwahe@gmail.com>.
Reviewed by: cognet@
#NO_UNIVERSE. Many of these config files are important examples, but
add little to no regresive value to the intended purpose of
UNIVERSE. We now build over 120 kernels during universe. There's
really little to no value to this over building say 60 or even 30 of
them (either is still a way too big number). This is especially true
for kernels that are nothing more than including a common base and
adding a static DTB file. Start by pruning 1/3 of the arm kernels that
add little regresion value.
Flushing the caches is required before doing a panic dump, but ARM
doesn't provide a flavor of flush that gets broadcast to other cores.
However, all cores except one are stopped before doing a dump, so this
works around the lack of a global flush/invalidate by doing it locally
on each CPU as part of stopping.
Discussed with: cognet@
This was added ca. 2004 for the purpose of ensuring the caches were in the
right state after the debugger set a breakpoint. kdb_cpu_sync_icache()
was added in 2007 to handle that situation, and now the wbinv_all is
actually harmful because the operation isn't broadcast to other cores.
using armv7_idcache_wbinv_all, because wbinv_all doesn't broadcast the
operation to other cores. In elf_cpu_load_file() use icache_sync_all()
and explain why it's needed (and why other sync operations aren't).
As part of doing this, all callers of cpu_icache_sync_all() were
inspected to ensure they weren't relying on the old side effect of
doing a wbinv_all along with the icache work.
the cpufreq code. Replace its use with smp_started. There's at least
one userland tool that still looks at the kern.smp.active sysctl, so
preserve it but point it to smp_started as well.
Discussed with: peter, jhb
MFC after: 3 days
Obtained from: Netflix
define a few imx_ccm_foo() functions that are implemented by the imx51 or
imx6 ccm code. Of course, the imx6 ccm code is still more a wish than
reality, so for now its implementations just return hard-coded numbers.
- These were needed on armv4/5 (VIVT cache), not needed on armv6.
- The wbinv_all call can't be used on SMP systems; cache operations by
set/way are not broadcast to other cores.
- The TLB maintenance operations needed for pmap_growkernel() happen in
pmap_grow_l2_bucket(), so there's no need to flush all TLB entries at
the end.
- There may not be any need for the TLB flush at the beginning of
pmap_release(), but it's left in for now pending more investigation.
Pointed out by: Svatopluk Kraus <onwahe@gmail.com>
Discussed with: cognet@
While it is the recommended initialization procedure, it hangs on the reset
of the second GPIO module on pandaboard.
Removes the module reset for now as more investigation would be needed.
Reported by: jceel
These should have been part of r264129, they are part of the overall set
of changes that got several weeks of testing. I must have fumbled them
while merging various patchsets.
On AM335x each one of the four GPIO banks has two physical interrupt
lines, so we now allocate resources and setup our interrupt handler for
all the (8) available interrupts.
On OMAP3 and OMAP4 there is only one interrupt for each GPIO bank (6
banks, 6 interrupts), but there are two set of registers where the
first one is used to setup the delivery of interrupts to the MPU and
the second set, setup the delivery of interrupts to the DSP.
On AM335x, each set of registers controls each one of the interrupt
lines.
- Remove nonexistent registers for OMAP4 and AM335x, replace their use with
the correct ones for these SoCs.
- Remove stray whitespace.
Based on OMAP3, OMAP4 and AM335x TRMs.
Tested on Beaglebone-black.
enabled. Also switch IMX6 to use SCHED_ULE.
The now-unreferenced WANDBOARD.common config will be deleted after giving
folks who may be including it a heads-up to switch to IMX6.
- Add cpu_cpwait to comply with the convention.
- Add missing TLB invalidations, especially in pmap_kenter & pmap_kremove
with distinguishing between D and ID pages.
- Modify pmap init/bootstrap invalidations to ID, just to be safe.
- Fix TLB-inv and PTE_SYNC ordering.
This combines changes submitted by ian@, cognet@, and Wojciech Macek,
which have all been tested together as a unit.
Perform sychronization (by "isb" barrier) after TTB is set. This
is done to ensure that TLB invalidation always executes after
TTB modification and operates on valid CP15 data (per specification).
Submitted by: Wojciech Macek <wma@semihalf.com>
Reviewed by: ian@, cognet@
- Don't allow high-speed mode on OMAP4 due to hardware erratum.
- Check the proper bit in the status register when waiting for the
controller to come out of reset.
- Add handling for the "non-removable" fdt property by always returning
"card is present" status.
- Add the non-removable property for the MMC card on a Beaglebone Black.
- Add the non-removable property for Pandaboard as a workaround.
For Pandaboard the card detect pin is handled by the twl6030 fpga device
which gets an interrupt on pin change and then has to query the fpga
for the actual status. We don't have code to do that yet.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
errors.
Reset the GPIO module during the initialization. This is guaranteed to be
the same as a hardware reset. Tested on AM335x (BBB) and checked against
the omap3 and omap4 TRM.
Do a better job freeing resources when there are errors and on
ti_gpio_detach().
We don't know our ARM security state, so one of them will operate.
- Don't set frequency, since it's unpossible in non-secure state.
Only rely on DTS clock-frequency value or get clock from timer.
Discussed with: ian, cognet
This adds the concept of "operating points," combinations of frequency
and voltage at which the cpu is known to work correctly. Some day these
should come from FDT data, but for now the table is hard-coded.
This also allows tuning the min and max operating frequencies. The min
frequency is what the thermal management code will slow down to if the
core temperature gets too high. The max frequency is what gets used if
the temperature is okay.
Normally the max cannot be set higher than the value burned into the
ocotp fuses as the chip's rated max, but there is now a new sysctl+tunable
cpu_overclock_enable; when set to non-zero it allows raising the frequency
above the ocotp value: USE WITH CARE! (At least one of my imx6 boards
has a cpu whose ocotp values never got set correctly; they claim a max
of 792mhz, but the physical markings on the chip say it's good to 1ghz.)
Because all these values affect the entire SoC, there is a new sysctl
node, hw.imx6, where all these values live. The values that are currently
under dev.imx6_anatop.0 should probably move to hw.imx6 too, because
"anatop" doesn't even mean anything to me, let alone to an end user.
description was eaten by the dog (or an editor crash or something).
Add variable-frequency support to the arm mpcore eventtimer driver.
This allows a platform's early init code to tell the mpcore driver that the
clock frequency can vary. That causes the mpcore driver to register an
eventtimer, but not a timecounter. The platform has to provide a time
counter using some other fixed-frequency clock, but can still use the
per-cpu goodness of the mpcore hardware for event timers.
When the platform support code does something to change the frequency of
the CPU clocks (power saving, thermal management) it must tell the mpcore
driver code about it using arm_tmr_change_frequency().
register values, then restart the timer. This prevents a situation where
an old event fires just as we're about to load a new value into the timer,
when the start routine is called to change the time of the current event.
Also re-nest the parens properly for casting the result of converting
time and frequency to a count. This doesn't actually change the result of
the calcs, but will some day prevent a loss-of-precision warning on the
assignment, if that warning gets enabled.
Support covers device drivers for:
- Interrupt Combiner
- gpio/pad, External Interrupts Controller (pad)
- I2C Interface
- Chrome Embedded Controller
- Chrome Keyboard
Also:
- Use new gpio dev class in EHCI driver
- Expand device tree information
* Save the required VFP registers on context switch. If the exception bit
is set we need to save and restore the FPINST register, and if the fp2v
bit is also set we need to save and restore FPINST2.
* Move saving and restoring the floating point control registers to C.
* Clear the fpexc exception and fp2v flags on a floating-point exception.
* Signal a SIGFPE if the fpexc exception flag is set on an undefined
instruction. This is how the ARM core signals to software there is a
floating-point exception.
The ADC has a 12bit resolution and its raw output can be read via sysctl(8)
interface.
The driver allows the setup of ADC clock, samples average and open delay
(the number of clock cycles to wait before start the conversion).
The TSC_ADC module is set in the general purpose mode (no touchscreen
support).
Tested on Beaglebone-black.
Written based on AM335x TRM.
Reviewed by: rpaulo
Approved by: adrian (mentor)
Tested by: me, Brian J. McGovern, Sulev-Madis Silber (ketas)
To reduce the diff struct pcu.cnt field was not renamed, so
PCPU_OP(cnt.field) is still used. pc_cnt and pcpu are also used in
kvm(3) and vmstat(8). The goal was to not affect externally used KPI.
Bump __FreeBSD_version_ in case some out-of-tree module/code relies on the
the global cnt variable.
Exp-run revealed no ports using it directly.
No objection from: arch@
Sponsored by: EMC / Isilon Storage Division
The armv7 architecture uses a unified TLB model for maintenence ops even
if separate instruction and data TLBs are implemented in hardware. That
means that there's no distinction between the 'I' and 'D' flavors of flush,
they all use the same 'ID' implementation. On the other hand, there is a
difference between SMP and UP on armv7, but not on arm11, so use the armv7
routines for cortex-a processors.
further refinement is required as some device drivers intended to be
portable over FreeBSD versions rely on __FreeBSD_version to decide whether
to include capability.h.
MFC after: 3 weeks
which was added by cognet in 2012, so remove the no-longer-applicable
license stuff that referred to all the old contents, and put in a
standard 2-clause BSD license (to cover the 6 lines of useful code left
in here).
swi_exit code in exception.S instead of having its own inline expansion
of the DO_AST and PULLFRAME macros. That means that now all references
to the PUSH/PULLFRAME and DO_AST macros are localized to exception.S,
so move the macros themselves into there and remove them from asmacros.h
and eliminate vectors.S. All low-level exception handling is now
consolidated into exception.S.
Along with moving the default FIQ handler, change it to disable FIQs
before returning. An FIQ should never happen, but if it does, it's got
to be disabled as part of ignoring it.
In general, we have hand-wavy support for FIQs that probably hasn't been
used for 10 years and probably doesn't work (almost certainly doesn't
work for SMP because it only updates the vector on the current cpu). This
change doesn't really make the overall situation any better or worse.
and the functionality it provided into arm/exception.S. Rename the main
irq handling routine from arm_handler_execute() to arm_irq_handler() to
make it more congruent with how other exception handlers are named, and
also update its signature to reflect what has long been reality: it is
passed just a trapframe pointer, no interrupt number argument.
never actually ran on these chips (other than using SA1 support in an
emulator to do the early porting to FreeBSD long long ago). The clutter
and complexity of some of this code keeps getting in the way of other
maintenance, so it's time to go.
to the actual handler routine. All the pointers are static-intialized to
the only handlers available, and yet various platform-specific inits still
set those pointers (to the values they're already initialized to). Begin
to drain the swamp by removing all the redundant external declarations and
runtime setting of the pointers that's scattered around various places.
The old code used static storage to preserve a couple registers while
setting up the trapframe for the main handler. Doing so was the last
leftover crumbs from the days when a low-level debugger was hooked into
the exception entry code.
Now the exception entry sequence is essentially the same as for the
other exceptions, which still involves needlessly indirecting through
a function pointer which points to the same code on every platform.
Removing that indirection will be handled as a separate cleanup.
This work is based on an analysis by Juergen Weiss.
enabled. In vfp_discard(), if the state in the VFP hardware belongs to
the thread which is dying, NULL out pcpu fpcurthread to indicate the
state currently in the hardware belongs to nobody.
Submitted by: Juergen Weiss
Pointy hat to: me
a leftover from the days when a low-level debugger had hooks in the
undefined exception vector and needed stack space to function. These days
it effectively isn't used because we switch immediately to the svc32 mode
stack on exception entry. For that, the single undef mode stack per core
that gets set up at init time works fine.
The stack wasn't necessary but it was harmful, because the space for it
was carved out of the normal per-thread svc32 stack, in effect cutting
that 8K stack in half. If svc32 mode used more than 4k of stack space it
wandered down into the undef mode stack, and then an undef exception would
overwrite a couple words on the stack while switching to svc32 mode,
corrupting the scv32 stack. Having another stack abut the bottom of the
svc32 stack also effectively mooted the guard page below the stack.
This work is based on analysis and patches submitted by Juergen Weiss.
The old code was full of complexity that would only matter if the
kernel itself used the VFP hardware. Now that's reduced to either killing
the userland process or panicking the kernel on an illegal VFP instruction.
This removes most of the complexity from the assembler code, reducing it
to just calling the save code if the outgoing thread used the VFP.
The routine that stores the VFP state now takes a flag that indicates
whether the hardware should be disabled after saving state. Right now it
always is, but this makes the code ready to be used by get/set_mcontext()
(doing so will be addressed in a future commit).
Remove the arm-specific pc_vfpcthread from struct pcpu and use the MI
field pc_fpcurthread instead.
Reviewed by: cognet
appropriate for each of the 'foo' in the tree. This will allow us to
compile them together (although symbol conflicts prevent us from doing
that today, this just fixes the file name collision).
struct sigframe containing the struct ucontext.
The signal trampoline return code on the other hand DOES have just a
struct sigframe on the stack to work with, so have it get a pointer to
the ucontext out of there to pass along to sys_sigreturn.
In other words, make everything work right whether sys_sigreturn is
invoked from the trampoline or from userland code calling sigreturn(2).
Submitted by: Takashi Komatsu <komatsu.taka@jp.panasonic.com>
Reviewed by: cognet
It is available mostly in A10 devices like Hackberry, Marsboard,
Mele A1000, A2000, A100 HTPC, cubieboard1 and A20 device
like cubieboard2.
TX performance can be improved using both channels 0 and 1.
RX performance is poor and needs improvement with the assistance of
external DMA controller in case there is bulk TCP receiver.
Reviewed by: yongari@
Approved by: stas (mentor)
we've been using was actually just spinning due to ARM having redefined
the old 'wait for interrupt' operation via the system coprocessor as a nop
and replacing it with a WFI instruction.
code can supply a better implementation. A SoC with variable CPU frequency
is likely to use a fixed-frequency timer for DELAY() (but still use the
mpcore private timers as eventtimers).
Also remove spaces from the eventtimer and timecounter names.
implementation in arm/machdep.c. Most arm platforms either don't need to
do anything, or just need to call the standard eventtimer init routines.
A generic implementation that does that is now provided via weak linkage.
Any platform that needs to do something different can provide a its own
implementation to override the generic one.
- Don't use spaces or dots in the eventtimer or timecounter names.
They turn into sysctl node names, and it's just confusing.
- Use comparator #3 instead of #1 for one-shot events. There's an
extra 1-cycle penalty in the hardware for accessing the registers
for comparator 1, no point in paying that penalty.
- Lower the quality of the eventtimer from 1000 to 800, because the
device can't support PERCPU timers and some other device in the system
may be able to provide that.
Quartz is a tiny module utilized Freescale VF6xx
system-on-chip and development kit produced by
Device Solutions.
Quartz is available in a form of LGA (38x38x2mm)
or as a module with high-density connectors.
Sponsored by: Device Solutions
the Bufferable bit in the PDE entries of the secondary processor startup
pagetables.
The caches really need to be invalidated even earlier than this, but this
is a big step in the right direction. The invalidate needs to happen
before the MMU is enabled, which means it has to be called from asm code
that's running with physical addressing. Fixing that will be handled in
a future change.
implementations for each of the chips we support. Most chips up through
armv6 can use the armv4 implementation which has a single coprocessor
opcode for this operation. The rather more complex armv7 implementation
comes from netbsd.
While this is technically more correct, I don't think it much matters,
because the only thing in the tree that calls cpu_flush_dcache() is md(4)
and I'm > 99% sure it's bogus that it does so; md has no ability to do
anything that can perturb data cache coherency.
it into a bunch of different .c files. Remove declarations for the unused
mptramp() function from everywhere except AramadaXP (and I think it's
really not used there either, because the code that references it appears
to be insanely does-nothing in nature).
WANDBOARD.common config, but with the freescale-specific optons and devices
all together at the bottom now. In addition to reformatting and shuffling
lines around, two new options are added because they're now known to work,
VFP and FREEBSD_BOOT_LOADER.
This config does not include any static DTB, it requires that u-boot
provide a DTB (or a custom kernel config can compile one in).
This will supercede all the existing WANDBOARD* configs, but those will
be left around for a while to help people transition their customized
configs to include this new one instead.
The temperature monitor device is enabled to sample the die temperature at
16hz. The temperature is published via sysctl. A callout routine at 10hz
monitors the temperature and throttles back the cpu if the temperature
goes over a user-settable throttle point (by default 10C less than the
critical high-point temperature for the chip). The hardware is supposed
to be able to deliver an interrupt when the temperature exceeds a settable
limit, but the interrupt never arrives so for now a callout does the job.
At attach time we read the maximum cpu frequency the chip is allowed to run
at and the cpu is set to run at that speed. It's reported at attach time.
A sysctl variable reports the current speed when queried.
New sysctl values:
dev.imx6_anatop.0.cpu_mhz: 984
dev.imx6_anatop.0.temperature: 37.9C
dev.imx6_anatop.0.throttle_temperature: 95.0C
Steven Lawrance did the initial heavy lifting on this, but I changed
enough stuff that I'm the one to blame if anything breaks.
Submitted by: Steven Lawrance <stl@koffein.net>
and CAMBRIA boards that does not use loader to load the kernel. This
is basically how it was done for i386. This way tunables can also be
set. For example in config file:
env "/conf/AVILA.env"
And in AVILA.env:
vfs.unmapped_buf_allowed=0
MFC after: 2 weeks
is attached, by establishing a temporary mapping of the registers when
necessary. This is a temporary measure to keep progress moving; in the
long run we need better control over the order in which devices attach
(better than "the order they appear in the fdt dts source").
Attempt to demote the superpage if trying to pmap_enter() on
one. Panic only when the particular superpage should
no longer exist for that pmap and address.
Because pmap_enter_locked() is called from few different functions
some redundancy in superpage promotion attempts can be observed.
Hence, avoid promotion in pmap_enter_object() (if the object can
be mapped by superpage it will be handled by pmap_enter_object()
itself) and also do not waste time in pmap_enter_quick().
From now on the promotion will be performed only in pmap_enter().
It was possible to create RW superpage mapping even if
the base pages were RO due to wrong setting of the prot
flag passed to pmap_map_section().
Promotion attempt should be canceled in case of attributes
mismatch between any two base pages. Since we still use
pv_flags to maintain permission to write (PVF_WRITE) and
wired status (PVF_WIRED) for a page, it is also necessary
to take those variables into account.
Invalidate L1 PTE regardles of existance of the corresponding
l2_bucket. This is relevant when superpage is entered via
pmap_enter_object() and will fix crash on entering page
in place of not properly removed superpage.
because we use the 1MiB section maps as they only need a single pagetable.
To allow this we only use pc relative loads to ensure we only load from
physical addresses until we are running from a known virtual address.
As a side effect any data from before or 64MiB after the kernel needs to
be mapped in to be used. This should not be an issue for kernels loaded
with ubldr as it places this data just after the kernel. It will be a
problem when loading directly from anything using the Linux ABI that
places the ATAG data outside this range, for example U-Boot.
Add gpioled(4) to BEAGLEBONE kernel and add the description of the four
on-board leds of beaglebone-black to its DTS file.
Approved by: adrian (mentor, implicit)
