Otherwise kernel traps on NULL dereference if fpu_kern(9) is used from the
thread0 context.
Reported by: cem
Reviewed by: cem, jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
PG_PROMOTED, that indicates whether lingering 4KB page mappings might
need to be flushed on a PDE change that restricts or destroys a 2MB
page mapping. This flag allows the pmap to avoid range invalidations
that are both unnecessary and costly.
Reviewed by: kib, markj
MFC after: 6 weeks
Differential Revision: https://reviews.freebsd.org/D9665
show pte from the pmap of the process of the current DDB thread, instead
of necessarily the PCPU pmap.
Submitted by: Ryan Libby <rlibby@gmail.com>
Reviewed by: kib
MFC after: 1 week
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D9645
This also adds support for LINUX_ARCH_SET_GS.
Reviewed by: dchagin
MFC after: 2 weeks
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9372
For the loop that dirties vm_pages in case superpage was written to,
check the complete condition before the loop.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Implement get_pcpu() for amd64/sparc64/mips/powerpc, and use it to
replace pcpu_find(curcpu) in MI code.
Reviewed by: andreast, kan, lidl
Tested by: lidl(mips, sparc64), andreast(powerpc)
Differential Revision: https://reviews.freebsd.org/D9587
MTRR handlers are set in {amd64/i686}_mem_drvinit, which is called at
SI_SUB_DRIVERS, and that's too late when EARLY_AP_STARTUP is set because APs
have already started at this point. {amd64/i686}_mrinit is also called too late
for the BSP, since that happens when the memory device is attached, also after
APs have already started.
Move the position to SI_SUB_CPU, and also initialize the state for the BSP, so
that the APs can correctly get to the same state as the BSP.
Sponsored by: Citrix Systems R&D
MFC after: 1 week
Reviewed by: jhb, kib
Differential Revision: https://reviews.freebsd.org/D9630
but it allows to use 64 bit linux strace(1) on 64 bit linux binaries.
Reviewed by: dchagin (earlier version)
MFC after: 2 weeks
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9406
Refresh upstream driver before impending conversion to iflib.
Major new features:
- Support for Fortville-based 25G adapters
- Support for I2C reads/writes
(To prevent getting or sending corrupt data, you should set
dev.ixl.0.debug.disable_fw_link_management=1 when using I2C
[this will disable link!], then set it to 0 when done. The driver implements
the SIOCGI2C ioctl, so ifconfig -v works for reading I2C data,
but there are read_i2c and write_i2c sysctls under the .debug sysctl tree
[the latter being useful for upper page support in QSFP+]).
- Addition of an iWARP client interface (so the future iWARP driver for
X722 devices can communicate with the base driver).
- Compiling this option in is enabled by default, with "options IXL_IW" in
GENERIC.
Differential Revision: https://reviews.freebsd.org/D9227
Reviewed by: sbruno
MFC after: 2 weeks
Sponsored by: Intel Corporation
and wrong numbering for a few unimplemented syscalls.
For 32-bit Linuxulator, socketcall() syscall was historically
the entry point for the sockets API. Starting in Linux 4.3, direct
syscalls are provided for the sockets API. Enable it.
The initial version of patch was provided by trasz@ and extended by me.
Submitted by: trasz
MFC after: 2 week
Differential Revision: https://reviews.freebsd.org/D9381
The switch to get_pcpu() in MI code seems to cause hangs on MIPS.
Back out until we can get a better idea of what's happening there.
Reported by: kan, lidl
protection change.
On superpage promotion, x86 pmaps do not invalidate existing 4K
entries for the superpage range, because they are compatible with the
promoted 2/4M entry. But the invalidation on superpage removal or
protection change only did single INVLPG with the base address of the
superpage. This reliably flushed superpage TLB entry, and 4K entry
for the first page of the superpage, potentially leaving other 4K TLB
entries lingering. Do the invalidation of the whole superpage range
to correct the problem.
Note that the precise invalidation is done by x86 code for kernel_pmap
only, for user pmaps whole (per-AS) TLB is flushed. This made the bug
well hidden, because promotions of the kernel mappings require
specific load.
Reported and tested by: Jonathan Looney <jtl@netflix.com> (previous version)
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
SDM states that CLFLUSHOPT instructions can be ordered with other
writes by SFENCE, heavier MFENCE is not required.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
The error is:
vmm_dev.c: In function 'alloc_memseg':
vmm_dev.c:261:11: error: null argument where non-null required (argument 1) [-Werror=nonnull]
Apparently, the gcc is unable to figure out that if a ternary operator
produced a non-NULL value once, then the operator with exactly the same
operands would produce the same value again.
MFC after: 1 week
We would previously invalidate such entries individually, resulting in more
IPIs than necessary.
Reviewed by: alc, kib
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D9094
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
hammer_time(). This makes assembler exception handlers not fault
itself when setting PCB flags, and allow normal kernel trap handler to
get control. The pointer is reset after FPU parameters are obtained.
Set thread0.td_critnest to 1 for duration of hammer_time() as well.
In particular, page faults at that early stage panic immediately
instead of trying to call not yet operational VM to resolve it.
As result, faults during second half of the hammer_time() execution
have a chance to be reported instead of silent machine reboot or hang.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Changes include modifications in kernel crash dump routines, dumpon(8) and
savecore(8). A new tool called decryptcore(8) was added.
A new DIOCSKERNELDUMP I/O control was added to send a kernel crash dump
configuration in the diocskerneldump_arg structure to the kernel.
The old DIOCSKERNELDUMP I/O control was renamed to DIOCSKERNELDUMP_FREEBSD11 for
backward ABI compatibility.
dumpon(8) generates an one-time random symmetric key and encrypts it using
an RSA public key in capability mode. Currently only AES-256-CBC is supported
but EKCD was designed to implement support for other algorithms in the future.
The public key is chosen using the -k flag. The dumpon rc(8) script can do this
automatically during startup using the dumppubkey rc.conf(5) variable. Once the
keys are calculated dumpon sends them to the kernel via DIOCSKERNELDUMP I/O
control.
When the kernel receives the DIOCSKERNELDUMP I/O control it generates a random
IV and sets up the key schedule for the specified algorithm. Each time the
kernel tries to write a crash dump to the dump device, the IV is replaced by
a SHA-256 hash of the previous value. This is intended to make a possible
differential cryptanalysis harder since it is possible to write multiple crash
dumps without reboot by repeating the following commands:
# sysctl debug.kdb.enter=1
db> call doadump(0)
db> continue
# savecore
A kernel dump key consists of an algorithm identifier, an IV and an encrypted
symmetric key. The kernel dump key size is included in a kernel dump header.
The size is an unsigned 32-bit integer and it is aligned to a block size.
The header structure has 512 bytes to match the block size so it was required to
make a panic string 4 bytes shorter to add a new field to the header structure.
If the kernel dump key size in the header is nonzero it is assumed that the
kernel dump key is placed after the first header on the dump device and the core
dump is encrypted.
Separate functions were implemented to write the kernel dump header and the
kernel dump key as they need to be unencrypted. The dump_write function encrypts
data if the kernel was compiled with the EKCD option. Encrypted kernel textdumps
are not supported due to the way they are constructed which makes it impossible
to use the CBC mode for encryption. It should be also noted that textdumps don't
contain sensitive data by design as a user decides what information should be
dumped.
savecore(8) writes the kernel dump key to a key.# file if its size in the header
is nonzero. # is the number of the current core dump.
decryptcore(8) decrypts the core dump using a private RSA key and the kernel
dump key. This is performed by a child process in capability mode.
If the decryption was not successful the parent process removes a partially
decrypted core dump.
Description on how to encrypt crash dumps was added to the decryptcore(8),
dumpon(8), rc.conf(5) and savecore(8) manual pages.
EKCD was tested on amd64 using bhyve and i386, mipsel and sparc64 using QEMU.
The feature still has to be tested on arm and arm64 as it wasn't possible to run
FreeBSD due to the problems with QEMU emulation and lack of hardware.
Designed by: def, pjd
Reviewed by: cem, oshogbo, pjd
Partial review: delphij, emaste, jhb, kib
Approved by: pjd (mentor)
Differential Revision: https://reviews.freebsd.org/D4712
module loading is successful, but attempts to use it will not be
successful. This is similar to what we do (did?) with ACPI on non-ACPI
systems. We succeed if we can't find the necessary information to hook
into EFI, but still fail if we're unable to allocate resources if we
do find EFI.
Not Objected to by: kib@
MFC Afer: 3 days
If we load a binary that is designed to be a library, it produces
relocatable code via assembler directives in the assembly itself
(rather than compiler options). This emits R_X86_64_PLT32 relocations,
which are not handled by the kernel linker.
Submitted by: gallatin
Reviewed by: kib
contain a vm_page_t at the specified index. However, with this
change, vm_radix_remove() no longer panics. Instead, it returns NULL
if there is no vm_page_t at the specified index. Otherwise, it
returns the vm_page_t. The motivation for this change is that it
simplifies the use of radix tries in the amd64, arm64, and i386 pmap
implementations. Instead of performing a lookup before every remove,
the pmap can simply perform the remove.
Reviewed by: kib, markj
Differential Revision: https://reviews.freebsd.org/D8708
Rather than reporting a page fault due to a bad PTE as a protection
violation with the "rsv" flag, treat these faults as a separate type of
fault altogether.
MFC after: 1 month
Upstream the BUF_TRACKING and FULL_BUF_TRACKING buffer debugging code.
This can be handy in tracking down what code touched hung bios and bufs
last. The full history is especially useful, but adds enough bloat that
it shouldn't be enabled in release builds.
Function names (or arbitrary string constants) are tracked in a
fixed-size ring in bufs. Bios gain a pointer to the upper buf for
tracking. SCSI CCBs gain a pointer to the upper bio for tracking.
Reviewed by: markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8366
Previously these were only declared under #ifdef SMP in <machine/smp.h>.
However, these variables are defind in pmap.c unconditionally, and efirt.c
references them unconditionally. This fixes non-SMP kernel builds.
Discussed with: kib
MFC after: 1 week
Just using vm_paddr_t value with all bits set.
That should work as long as the type is unsigned.
While there, fix a couple of whitespace issues nearby.
MFC after: 1 week
X-MFC with: r307903
Reject attempts to read from or memory map offsets in /dev/mem that are
beyond the maximum-supported physical address of the current CPU.
Reviewed by: kib
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D7408
To achieve that the whole svm_softc is allocated with contigmalloc now.
It would be more effient to de-embed those arrays and allocate only them
with contigmalloc.
Previously, if malloc(9) used non-contiguous pages for the arrays, then
random bits in physical pages next to the first page would be used to
determine permissions for I/O port and MSR accesses. That could result
in a guest dangerously modifying the host hardware configuration.
One example is that sometimes NMI watchdog driver in a Linux guest
would be able to configure a performance counter on a host system.
The counter would generate an interrupt and if hwpmc(4) driver is loaded
on the host, then the interrupt would be delivered as an NMI.
Discussed with: jhb
Reviewed by: grehan
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8321
- Make !KDB config buildable.
- Simplify interface to nmi_handle_intr() by evaluating panic_on_nmi
in one place, namely nmi_call_kdb(). This allows to remove do_panic
argument from the functions, and to remove i386/amd64 duplication of
the variable and sysctl definitions. Note that now NMI causes
panic(9) instead of trap_fatal() reporting and then panic(9),
consistently for NMIs delivered while CPU operated in ring 0 and 3.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
On several Intel chipsets, diagnostic NMIs sent from BMC or NMIs
reporting hardware errors are broadcasted to all CPUs.
When kernel is configured to enter kdb on NMI, the outcome is
problematic, because each CPU tries to enter kdb. All CPUs are
executing NMI handlers, which set the latches disabling the nested NMI
delivery; this means that stop_cpus_hard(), used by kdb_enter() to
stop other cpus by broadcasting IPI_STOP_HARD NMI, cannot work. One
indication of this is the harmless but annoying diagnostic "timeout
stopping cpus".
Much more harming behaviour is that because all CPUs try to enter kdb,
and if ddb is used as debugger, all CPUs issue prompt on console and
race for the input, not to mention the simultaneous use of the ddb
shared state.
Try to fix this by introducing a pseudo-lock for simultaneous attempts
to handle NMIs. If one core happens to enter NMI trap handler, other
cores see it and simulate reception of the IPI_STOP_HARD. More,
generic_stop_cpus() avoids sending IPI_STOP_HARD and avoids waiting
for the acknowledgement, relying on the nmi handler on other cores
suspending and then restarting the CPU.
Since it is impossible to detect at runtime whether some stray NMI is
broadcast or unicast, add a knob for administrator (really developer)
to configure debugging NMI handling mode.
The updated patch was debugged with the help from Andrey Gapon (avg)
and discussed with him.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D8249
These two ALU instructions first appeared on Linux. Then, libpcap adopted
and made them available since 1.6.2. Now more platforms including NetBSD
have them in kernel. So do we.
--이 줄 이하는 자동으로 제거됩니다--
Split efirt.ko initialization into early stage where runtime services
KPI environment is created, to be used e.g. for RTC, and the later
devfs node creation stage, per module.
Switch the efi device to use make_dev_s(9) instead of make_dev(9). At
least, this gracefully handles the duplicated device name issue.
Remove ARGSUSED comment from efidev_ioctl(), all unused arguments are
annotated with __unused attribute.
Reported by: ambrisko, O. Hartmann <ohartman@zedat.fu-berlin.de>
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Using the device pager with /dev/kmem is not stable since KVA mappings
are transient, but the device pager caches the PA associated with a
given offset forever. Interestingly, mips' implementation of
memmap() already refused requests for /dev/kmem.
Note that kvm_read/kvm_write do not use mmap, but use read and write on
/dev/kmem, so this should not affect libkvm users.
Reviewed by: kib
MFC after: 2 months
to add actions that run when a TCP frame is sent or received on a TCP
session in the ESTABLISHED state. In the base tree, this functionality is
only used for the h_ertt module, which is used by the cc_cdg, cc_chd, cc_hd,
and cc_vegas congestion control modules.
Presently, we incur overhead to check for hooks each time a TCP frame is
sent or received on an ESTABLISHED TCP session.
This change adds a new compile-time option (TCP_HHOOK) to determine whether
to include the hhook(9) framework for TCP. To retain backwards
compatibility, I added the TCP_HHOOK option to every configuration file that
already defined "options INET". (Therefore, this patch introduces no
functional change. In order to see a functional difference, you need to
compile a custom kernel without the TCP_HHOOK option.) This change will
allow users to easily exclude this functionality from their kernel, should
they wish to do so.
Note that any users who use a custom kernel configuration and use one of the
congestion control modules listed above will need to add the TCP_HHOOK
option to their kernel configuration.
Reviewed by: rrs, lstewart, hiren (previous version), sjg (makefiles only)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D8185
userland. It supports userland interfaces to UEFI Runtime Services. This is
indended to the the MI portion of EFI RuntimeServices support.
Differential Revision: https://reviews.freebsd.org/D8128
Reviewed by: kib@, wblock@, Ganael Laplanche
Reduce the cost of TLB invalidation on x86 by using per-CPU completion flags
Reduce contention during TLB invalidation operations by using a per-CPU
completion flag, rather than a single atomically-updated variable.
On a Westmere system (2 sockets x 4 cores x 1 threads), dtrace measurements
show that smp_tlb_shootdown is about 50% faster with this patch; observations
with VTune show that the percentage of time spent in invlrng_single_page on an
interrupt (actually doing invalidation, rather than synchronization) increases
from 31% with the old mechanism to 71% with the new one. (Running a basic file
server workload.)
Submitted by: Anton Rang <rang at acm.org>
Reviewed by: cem (earlier version)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8041
Reduce contention during TLB invalidation operations by using a per-CPU
completion flag, rather than a single atomically-updated variable.
On a Westmere system (2 sockets x 4 cores x 1 threads), dtrace measurements
show that smp_tlb_shootdown is about 50% faster with this patch; observations
with VTune show that the percentage of time spent in invlrng_single_page on an
interrupt (actually doing invalidation, rather than synchronization) increases
from 31% with the old mechanism to 71% with the new one. (Running a basic file
server workload.)
Submitted by: Anton Rang <rang at acm.org>
Reviewed by: cem (earlier version), kib
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8041
like other PCI network drivers. The sys/ofed directory is now mainly
reserved for generic infiniband code, with exception of the mthca driver.
- Add new manual page, mlx4en(4), describing how to configure and load
mlx4en.
- All relevant driver C-files are now prefixed mlx4, mlx4_en and
mlx4_ib respectivly to avoid object filename collisions when compiling
the kernel. This also fixes an issue with proper dependency file
generation for the C-files in question.
- Device mlxen is now device mlx4en and depends on device mlx4, see
mlx4en(4). Only the network device name remains unchanged.
- The mlx4 and mlx4en modules are now built by default on i386 and
amd64 targets. Only building the mlx4ib module depends on
WITH_OFED=YES .
Sponsored by: Mellanox Technologies
i.e. SandyBridge and IvyBridge, correct a race between pmap_activate()
and invltlb_pcid_handler().
Reported by and tested by: Slawa Olhovchenkov <slw@zxy.spb.ru>
MFC after: 1 week
early printfs and debugging of vm86 initialization and some other early
initialization in some cases.) Add an option debug.late_console (with
default 1=off) to move console and kdb initialization back where it was.
Do the same for amd64 although there is no vm86 there.
On my test system, debug.late_console=0 works for the syscons, sio and
uart console drivers on amd64 and i386, and for vt on i386 but not on
amd64.
The early printfs fixed by debug.late_console=0 are:
- on i386, the message about lost memory above 4G
- with -v in otherwise normal use, about 20 printfs for SMAP
- other debugging messages for memory sizing. Mostly under -v and
not printed in normal use.
Document in a comment how much earlier the initialization and early
printf()s can be. That is very early for the console. Not much more
than curthread is needed. kdb use obviously needs to be not so early,
since it needs IDT initialization and that is done relatively late
for convenience and historical reasons.
Runtime services require special execution environment for the call.
Besides that, OS must inform firmware about runtime virtual memory map
which will be active during the calls, with the SetVirtualAddressMap()
runtime call, done while the 1:1 mapping is still used. There are two
complication: the SetVirtualAddressMap() effectively must be done from
loader, which needs to know kernel address map in advance. More,
despite not explicitely mentioned in the specification, both 1:1 and
the map passed to SetVirtualAddressMap() must be active during the
SetVirtualAddressMap() call. Second, there are buggy BIOSes which
require both mappings active during runtime calls as well, most likely
because they fail to identify all relocations to perform.
On amd64, we can get rid of both problems by providing 1:1 mapping for
the duration of runtime calls, by temprorary remapping user addresses.
As result, we avoid the need for loader to know about future kernel
address map, and avoid bugs in BIOSes. Typically BIOS only maps
something in low 4G. If not runtime bugs, we would take advantage of
the DMAP, as previous versions of this patch did.
Similar but more complicated trick can be used even for i386 and 32bit
runtime, if and when the EFI boot on i386 is supported. We would need
a trampoline page, since potentially whole 4G of VA would be switched
on calls, instead of only userspace portion on amd64.
Context switches are disabled for the duration of the call, FPU access
is granted, and interrupts are not disabled. The later is possible
because kernel is mapped during calls.
To test, the sysctl mib debug.efi_time is provided, setting it to 1
makes one call to EFI get_time() runtime service, on success the efitm
structure is printed to the control terminal. Load efirt.ko, or add
EFIRT option to the kernel config, to enable code.
Discussed with: emaste, imp
Tested by: emaste (mac, qemu)
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
physical address of the EFI System Table. Add _KERNEL guard around
its declaration in sys/efi.h.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Note that lgdt() name is already used for function which, besides
loading GDT, also reloads segment descriptors cache, thus new function
is named bare_lgdt().
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
amd64 pmap.
The new pmap_pinit_pml4() function initializes the level 4 page table
with entries for the kernel mappings. Both functions are needed for
upcoming EFI Runtime Services support.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
i386-only section, and fix a comment about the amd64 kernel trapframe
not having stackregs.
tf_rsp doesn't need decoding on amd64, but had an old clone of i386
code to do this in 1 place, and since the amd64 kernel trapframe does
have stackregs, the result was an off-by-16 error for %rsp in an error
message.
While here, avoid using the old variable 'code' and remove it
in trap(). ('code' was meant for holding things like %dr6,
but is too small to hold %dr6 on amd64 and was reduced to an
obfuscation of tf_err, with early truncation on amd64.)
Submitted by: Michael Butler (imb@...)
This is not very easy to do, since ddb didn't know when traps are
for single-stepping. It more or less assumed that traps are either
breakpoints or single-step, but even for x86 this became inadequate
with the release of the i386 in ~1986, and FreeBSD passes it other
trap types for NMIs and panics.
On x86, teach ddb when a trap is for single stepping using the %dr6
register. Unknown traps are now treated almost the same as breakpoints
instead of as the same as single-steps. Previously, the classification
of breakpoints was almost correct and everything else was unknown so
had to be treated as a single-step. Now the classification of single-
steps is precise, the classification of breakpoints is almost correct
(as before) and everything else is unknown and treated like a
breakpoint.
This fixes:
- breakpoints not set by ddb, including the main one in kdb_enter(),
were treated as single-steps and not stopped on when stepping
(except for the usual, simple case of a step with residual count 1).
As special cases, kdb_enter() didn't stop for fatal traps or panics
- similarly for "hardware breakpoints".
Use a new MD macro IS_SSTEP_TRAP(type, code) to code to classify
single-steps. This is excessively complicated for bug-for-bug and
backwards compatibilty. Design errors apparently started in Mach
in ~1990 or perhaps in the FreeBSD interface in ~1993. Common trap
types like single steps should have a unique MI code (like the TRAP*
codes for user SIGTRAP) so that debuggers don't need macros like
IS_SSTEP_TRAP() to decode them. But 'type' is actually an ambiguous
MD trap number, and code was always 0 (now it is (int)%dr6 on x86).
So it was impossible to determine the trap type from the args.
Global variables had to be used.
There is already a classification macro db_pc_is_single_step(), but
this just gets in the way. It is only used to recover from bugs in
IS_BREAKPOINT_TRAP(). On some arches, IS_BREAKPOINT_TRAP() just
duplicates the ambiguity in 'type' and misclassifies single-steps as
breakpoints. It defaults to 'false', which is the opposite of what is
needed for bug-for-bug compatibility.
When this is cleaned up, MI classification bits should be passed in
'code'. This could be done now for positive-logic bits, since 'code'
was always 0, but some negative logic is needed for compatibility so
a simple MI classificition is not usable yet.
After reading %dr6, clear the single-step bit in it so that the type
of the next debugger trap can be decoded. This is a little
ddb-specific. ddb doesn't understand the need to clear this bit and
doing it before calling kdb is easiest. gdb would need to reverse
this to support hardware breakpoints, but it just doesn't support
them now since gdbstub doesn't support %dr*.
Fix a bug involving %dr6: when emulating a single-step trap for vm86,
set the bit for it in %dr6. Userland debuggers need this. ddb now
needs this for vm86 bios calls. The bit gets copied to 'code' then
cleared again.
Fix related style bugs:
- when clearing bits for hardware breakpoints in %dr6, spell the mask
as ~0xf on both amd64 and i386 to get the correct number of bits
using sign extension and not need a comment about using the wrong
mask on amd64 (amd64 traps for invalid results but clearing the
reserved top bits didn't trap since they are 0).
- rewrite my old wrong comments about using %dr6 for ddb watchpoints.
The 'cpu' and 'cpu_class' variables were always set to the same value
on amd64 and are legacy holdovers from i386. Remove them entirely on
amd64.
Reviewed by: imp, kib (older version)
Differential Revision: https://reviews.freebsd.org/D7888
SEL_UPL and sometimes PSL_VM. This is just a style change on amd64,
but on i386 it fixes 1 unimportant place where the PSL_VM check was
missing and starts fixing 1 important place where the PSL_VM check
had a logic error.
Fix logic errors in treating vm86 bioscall mode as kernel mode. The
main place checked all the necessary flags, but put the necessary
parentheses for the PSL_VM and PCB_VM86CALL checks in the wrong
place. The broken case is only reached if a vm86 bioscall uses a
%cs which is nonzero mod 4, but that is unusual -- most bios calls
start with %cs = 0xc000 or 0xf000 and rarely change it. Another
place was missing the check for PCB_VM86CALL, but was only reachable
if there are bugs virtualizing PSL_I.
Add a macro TF_HAS_STACKREGS() and use this instead of converting
open-coded checks of SEL_UPL, etc. to TRAPF_USERMODE() when we only
care about whether the frame has stack registers. This fixes 3
places in my recent fix for register variables in vm86 mode where I
messed up the PSL_VM check and cleans up other places.
The flag specifies that the block which uses FPU must be executed in
critical section, i.e. take no context switches, and does not need an
FPU save area during the execution.
It is intended to be applied around fast and short code pathes where
save area allocation is impossible or undesirable, due to context or
due to the relative cost of calculation vs. allocation.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Move PMAP_TS_REFERENCED_MAX out of the various pmap implementations and
into vm/pmap.h, and describe what its purpose is. Eliminate the archaic
"XXX" comment about its value. I don't believe that its exact value, e.g.,
5 versus 6, matters.
Update the arm64 and riscv pmap implementations of pmap_ts_referenced()
to opportunistically update the page's dirty field.
On amd64, use the PDE value already cached in a local variable rather than
dereferencing a pointer again and again.
Reviewed by: kib, markj
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D7836
Add routines to trigger a function level reset (FLR) of a PCI-express
device via the PCI-express device control register. This also includes
support routines to wait for pending transactions to complete as well
as calculating the maximum completion timeout permitted by a device.
Change the ppt(4) driver to reset pass through devices before attaching
to a VM during startup and before detaching from a VM during shutdown.
Reviewed by: imp, wblock (earlier version)
MFC after: 1 month
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7751
When the I/O MMU is active in bhyve, all PCI devices need valid entries
in the DMAR context tables. The I/O MMU code does a single enumeration
of the available PCI devices during initialization to add all existing
devices to a domain representing the host. The ppt(4) driver then moves
pass through devices in and out of domains for virtual machines as needed.
However, when new PCI devices were added at runtime either via SR-IOV or
HotPlug, the I/O MMU tables were not updated.
This change adds a new set of EVENTHANDLERS that are invoked when PCI
devices are added and deleted. The I/O MMU driver in bhyve installs
handlers for these events which it uses to add and remove devices to
the "host" domain.
Reviewed by: imp
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7667
This allows a pass through device to be reset to a normal device driver
on the host and reused on the host. ppt devices are now always active in
some I/O MMU domain when the I/O MMU is active, either the host domain
or the domain of a VM they are attached to.
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7666
Idle page zeroing has been disabled by default on all architectures since
r170816 and has some bugs that make it seemingly unusable. Specifically,
the idle-priority pagezero thread exacerbates contention for the free page
lock, and yields the CPU without releasing it in non-preemptive kernels. The
pagezero thread also does not behave correctly when superpage reservations
are enabled: its target is a function of v_free_count, which includes
reserved-but-free pages, but it is only able to zero pages belonging to the
physical memory allocator.
Reviewed by: alc, imp, kib
Differential Revision: https://reviews.freebsd.org/D7714
dependent pmap_ts_referenced() so that it updates the page's dirty field
if a modified bit is found while counting reference bits. This
opportunistic update can be performed at low cost and can eliminate the
need for some future calls to pmap_is_modified() by the machine-
independent layer.
Reviewed by: kib, markj
MFC after: 3 weeks
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D7722
for zeroing pages in idle where nontemporal writes are clearly best.
This is almost a no-op since zeroing in idle works does nothing good
and is off by default. Fix END() statement forgotten in previous
commit.
Align the loop in sse2_pagezero(). Since it writes to main memory,
the loop doesn't have to be very carefully written to keep up.
Unrolling it was considered useless or harmful and was not done on
i386, but that was too careless.
Timing for i386: the loop was not unrolled at all, and moved only 4
bytes/iteration. So on a 2GHz CPU, it needed to run at 2 cycles/
iteration to keep up with a memory speed of just 4GB/sec. But when
it crossed a 16-byte boundary, on old CPUs it ran at 3 cycles/
iteration so it gave a maximum speed of 2.67GB/sec and couldn't even
keep up with PC3200 memory. Fix the alignment so that it keep up with
4GB/sec memory, and unroll once to get nearer to 8GB/sec. Further
unrolling might be useless or harmful since it would prevent the loop
fitting in 16-bytes. My test system with an old CPU and old DDR1 only
needed 5+ GB/sec. My test system with a new CPU and DDR3 doesn't need
any changes to keep up ~16GB/sec.
Timing for amd64: with 8-byte accesses and newer faster CPUs it is
easy to reach 16GB/sec but not so easy to go much faster. The
alignment doesn't matter much if the CPU is not very old. The loop
was already unrolled 4 times, but needs 32 bytes and uses a fancy
method that doesn't work for 2-way unrolling in 16 bytes. Just
align it to 32-bytes.
same name as for i386). It is not reconnected yet.
Which method is better is too machine-dependent and system-dependent
to replace the old method unconditionally.
Rather than enabling the I/O MMU when the vmm module is loaded,
defer initialization until the first attempt to pass a PCI device
through to a guest. If the I/O MMU fails to initialize or is not
present, than fail the attempt to pass a PCI device through to a
guest.
The hw.vmm.force_iommu tunable has been removed since the I/O MMU is
no longer enabled during boot. However, the I/O MMU support can be
disabled by setting the hw.vmm.iommu.enable tunable to 0 to prevent
use of the I/O MMU on any systems where it is buggy.
Reviewed by: grehan
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D7448
A nice thing about requiring a vDSO is that it makes it incredibly easy
to provide full support for running 32-bit processes on 64-bit systems.
Instead of letting the kernel be responsible for composing/decomposing
64-bit arguments across multiple registers/stack slots, all of this can
now be done in the vDSO. This means that there is no need to provide
duplicate copies of certain system calls, like the sys_lseek() and
freebsd32_lseek() we have for COMPAT_FREEBSD32.
This change imports a new vDSO from the CloudABI repository that has
automatically generated code in it that copies system call arguments
into a buffer, padding them to eight bytes and zero-extending any
pointers/size_t arguments. After returning from the kernel, it does the
inverse: extracting return values, in the process truncating
pointers/size_t values to 32 bits.
Obtained from: https://github.com/NuxiNL/cloudabi
In all of these source files, the userspace pointer size corresponds
with the kernelspace pointer size, meaning that casting directly works.
As I'm planning on making 32-bit execution on 64-bit systems work as
well, use TO_PTR() here as well, so that the changes between source
files remain minimal.
Move msix_disable_migration under #ifdef SMP since it doesn't make sense
for !SMP kernels.
PR: 212014
Reported by: Glyn Grinstead <glyn@grinstead.org>
MFC after: 3 days
The si(4) driver supported multiport serial adapters for ISA, EISA, and
PCI buses. This driver does not use bus_space, instead it depends on
direct use of the pointer returned by rman_get_virtual(). It is also
still locked by Giant and calls for patch testing to convert it to use
bus_space were unanswered.
Relnotes: yes
CloudABI executables already provide support for passing in vDSOs. This
functionality is used by the emulator for OS X to inject system call
handlers. On FreeBSD, we could use it to optimize calls to
gettimeofday(), etc.
Though I don't have any plans to optimize any system calls right now,
let's go ahead and already pass in a vDSO. This will allow us to
simplify the executables, as the traditional "syscall" shims can be
removed entirely. It also means that we gain more flexibility with
regards to adding and removing system calls.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D7438
exception is caught in kernel mode. There are third-party modules
which trigger the issue, and since the problem causes usermode state
corruption at least, panic in production kernels as well.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
difference between files.
For pc98, put x86/mp_x86.c into the same place as used by i386 file list.
Fix typo in comment.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
The current implementation uses non-temporal writes. This turns out to
be detrimental to performance if the page is used shortly after, which
is the typical case with page faults.
Switch to rep stos.
Reviewed by: kib
MFC after: 1 week
Any sensible workflow will include a revision control system from which
to restore the old files if required. In normal usage, developers just
have to clean up the mess.
Reviewed by: jhb
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D7353
Set vm_guest to a new enum value (VM_GUEST_KVM) when kvm is detected and use
vm_guest in conditionals testing for KVM.
Also, fix a conditional checking if we're running in a VM which caught only
the generic VM case, but not more specific VMs (KVM, VMWare, etc.). (Spotted
by: vangyzen).
Differential revision: https://reviews.freebsd.org/D7172
Sponsored by: Dell Inc.
Approved by: kib (mentor), vangyzen (mentor)
Reviewed by: alc
MFC after: 4 weeks
If the hypervisor version is smaller than 4.6.0. Xen commits 74fd00 and
70a3cb are required on the hypervisor side for this to be fixed, and those
are only included in 4.6.0, so stay on the safe side and disable MSI-X
interrupt migration on anything older than 4.6.0.
It should not cause major performance degradation unless a lot of MSI-X
interrupts are allocated.
Sponsored by: Citrix Systems R&D
MFC after: 3 days
Reviewed by: jhb
Differential revision: https://reviews.freebsd.org/D7148
FreeBSD support NX bit on X86_64 processors out of the box, for i386 emulation
use READ_IMPLIES_EXEC flag, introduced in r302515.
While here move common part of mmap() and mprotect() code to the files in compat/linux
to reduce code dupcliation between Linuxulator's.
Reported by: Johannes Jost Meixner, Shawn Webb
MFC after: 1 week
XMFC with: r302515, r302516
In Linux if this flag is set, PROT_READ implies PROT_EXEC for mmap().
Linux/i386 set this flag automatically if the binary requires executable stack.
READ_IMPLIES_EXEC flag will be used in the next Linux mmap() commit.
It turns out that this value is not used within the system call code
under normal conditions, except when using tracing tools like ktrace.
If we forget to set this value, it is set to random garbage. This may
cause ktrace to hang indefinitely, making it impossible to kill.
Reported by: Michael Plass
PR: 210800
MFC before: 11.0-RELEASE
mp_maxid or CPU_FOREACH() as appropriate. This fixes a number of places in
the kernel that assumed CPU IDs are dense in [0, mp_ncpus) and would try,
for example, to run tasks on CPUs that did not exist or to allocate too
few buffers on systems with sparse CPU IDs in which there are holes in the
range and mp_maxid > mp_ncpus. Such circumstances generally occur on
systems with SMT, but on which SMT is disabled. This patch restores system
operation at least on POWER8 systems configured in this way.
There are a number of other places in the kernel with potential problems
in these situations, but where sparse CPU IDs are not currently known
to occur, mostly in the ARM machine-dependent code. These will be fixed
in a follow-up commit after the stable/11 branch.
PR: kern/210106
Reviewed by: jhb
Approved by: re (glebius)
threads, to make it less confusing and using modern kernel terms.
Rename the functions to reflect current use of the functions, instead
of the historic KSE conventions:
cpu_set_fork_handler -> cpu_fork_kthread_handler (for kthreads)
cpu_set_upcall -> cpu_copy_thread (for forks)
cpu_set_upcall_kse -> cpu_set_upcall (for new threads creation)
Reviewed by: jhb (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Approved by: re (hrs)
Differential revision: https://reviews.freebsd.org/D6731
does not cover the dynamically registered ficititious ranges, and
fictitious pages mappings are not promoted. Offer a dummy struct
md_page to fetch constant superpage pv list generation to satisfy
logic. Also, by initializing the pv_dummy pv_list to empty, we can
remove several explicit PG_FICTITIOUS tests.
Reported and tested by: Michael Butler <imb@protected-networks.net>
(previous version)
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D6728
Approved by: re (hrs)
Do not try to change attributes for DMAP when working on a mapping
which is not covered by the DMAP. This was reported on real system
where a BAR of a device (NTB) was mapped outside the PCI window.
Reported and tested by: mav
Reviewed by: jhb, mav
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D6668
The only current purpose of the pvh lock was explained there
On Wed, Jan 09, 2013 at 11:46:13PM -0600, Alan Cox wrote:
> Let me lay out one example for you in detail. Suppose that we have
> three processors and two of these processors are actively using the same
> pmap. Now, one of the two processors sharing the pmap performs a
> pmap_remove(). Suppose that one of the removed mappings is to a
> physical page P. Moreover, suppose that the other processor sharing
> that pmap has this mapping cached with write access in its TLB. Here's
> where the trouble might begin. As you might expect, the processor
> performing the pmap_remove() will acquire the fine-grained lock on the
> PV list for page P before destroying the mapping to page P. Moreover,
> this processor will ensure that the vm_page's dirty field is updated
> before releasing that PV list lock. However, the TLB shootdown for this
> mapping may not be initiated until after the PV list lock is released.
> The processor performing the pmap_remove() is not problematic, because
> the code being executed by that processor won't presume that the mapping
> is destroyed until the TLB shootdown has completed and pmap_remove() has
> returned. However, the other processor sharing the pmap could be
> problematic. Specifically, suppose that the third processor is
> executing the page daemon and concurrently trying to reclaim page P.
> This processor performs a pmap_remove_all() on page P in preparation for
> reclaiming the page. At this instant, the PV list for page P may
> already be empty but our second processor still has a stale TLB entry
> mapping page P. So, changes might still occur to the page after the
> page daemon believes that all mappings have been destroyed. (If the PV
> entry had still existed, then the pmap lock would have ensured that the
> TLB shootdown completed before the pmap_remove_all() finished.) Note,
> however, the page daemon will know that the page is dirty. It can't
> possibly mistake a dirty page for a clean one. However, without the
> current pvh global locking, I don't think anything is stopping the page
> daemon from starting the laundering process before the TLB shootdown has
> completed.
>
> I believe that a similar example could be constructed with a clean page
> P' and a stale read-only TLB entry. In this case, the page P' could be
> "cached" in the cache/free queues and recycled before the stale TLB
> entry is flushed.
TLBs for addresses with updated PTEs are always flushed before pmap
lock is unlocked. On the other hand, amd64 pmap code does not always
flushes TLBs before PV list locks are unlocked, if previously PTEs
were cleared and PV entries removed.
To handle the situations where a thread might notice empty PV list but
third thread still having access to the page due to TLB invalidation
not finished yet, introduce delayed invalidation. Comparing with the
pvh_global_lock, DI does not block entered thread when
pmap_remove_all() or pmap_remove_write() (callers of
pmap_delayed_invl_wait()) are executed in parallel. But _invl_wait()
callers are blocked until all previously noted DI blocks are leaved,
thus ensuring that neccessary TLB invalidations were performed before
returning from pmap_remove_all() or pmap_remove_write().
See comments for detailed description of the mechanism, and also for
the explanations why several pmap methods, most important
pmap_enter(), do not need DI protection.
Reviewed by: alc, jhb (turnstile KPI usage)
Tested by: pho (previous version)
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D5747
bus_get_cpus() returns a specified set of CPUs for a device. It accepts
an enum for the second parameter that indicates the type of cpuset to
request. Currently two valus are supported:
- LOCAL_CPUS (on x86 this returns all the CPUs in the package closest to
the device when DEVICE_NUMA is enabled)
- INTR_CPUS (like LOCAL_CPUS but only returns 1 SMT thread for each core)
For systems that do not support NUMA (or if it is not enabled in the kernel
config), LOCAL_CPUS fails with EINVAL. INTR_CPUS is mapped to 'all_cpus'
by default. The idea is that INTR_CPUS should always return a valid set.
Device drivers which want to use per-CPU interrupts should start using
INTR_CPUS instead of simply assigning interrupts to all available CPUs.
In the future we may wish to add tunables to control the policy of
INTR_CPUS (e.g. should it be local-only or global, should it ignore
SMT threads or not).
The x86 nexus driver exposes the internal set of interrupt CPUs from the
the x86 interrupt code via INTR_CPUS.
The ACPI bus driver and PCI bridge drivers use _PXM to return a suitable
LOCAL_CPUS set when _PXM exists and DEVICE_NUMA is enabled. They also and
the global INTR_CPUS set from the nexus driver with the per-domain set from
_PXM to generate a local INTR_CPUS set for child devices.
Compared to the r298933, this version uses 'struct _cpuset' in
<sys/bus.h> instead of 'cpuset_t' to avoid requiring <sys/param.h>
(<sys/_cpuset.h> still requires <sys/param.h> for MAXCPU even though
<sys/_bitset.h> does not after recent changes).
PCI-express HotPlug support is implemented via bits in the slot
registers of the PCI-express capability of the downstream port along
with an interrupt that triggers when bits in the slot status register
change.
This is implemented for FreeBSD by adding HotPlug support to the
PCI-PCI bridge driver which attaches to the virtual PCI-PCI bridges
representing downstream ports on HotPlug slots. The PCI-PCI bridge
driver registers an interrupt handler to receive HotPlug events. It
also uses the slot registers to determine the current HotPlug state
and drive an internal HotPlug state machine. For simplicty of
implementation, the PCI-PCI bridge device detaches and deletes the
child PCI device when a card is removed from a slot and creates and
attaches a PCI child device when a card is inserted into the slot.
The PCI-PCI bridge driver provides a bus_child_present which claims
that child devices are present on HotPlug-capable slots only when a
card is inserted. Rather than requiring a timeout in the RC for
config accesses to not-present children, the pcib_read/write_config
methods fail all requests when a card is not present (or not yet
ready).
These changes include support for various optional HotPlug
capabilities such as a power controller, mechanical latch,
electro-mechanical interlock, indicators, and an attention button.
It also includes support for devices which require waiting for
command completion events before initiating a subsequent HotPlug
command. However, it has only been tested on ExpressCard systems
which support surprise removal and have none of these optional
capabilities.
PCI-express HotPlug support is conditional on the PCI_HP option
which is enabled by default on arm64, x86, and powerpc.
Reviewed by: adrian, imp, vangyzen (older versions)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D6136
call pmap_invalidate_page() even though they are not destroying a leaf-
level page table entry.
Eliminate some bogus white-space characters in a comment.
Reviewed by: kib
bus_get_cpus() returns a specified set of CPUs for a device. It accepts
an enum for the second parameter that indicates the type of cpuset to
request. Currently two valus are supported:
- LOCAL_CPUS (on x86 this returns all the CPUs in the package closest to
the device when DEVICE_NUMA is enabled)
- INTR_CPUS (like LOCAL_CPUS but only returns 1 SMT thread for each core)
For systems that do not support NUMA (or if it is not enabled in the kernel
config), LOCAL_CPUS fails with EINVAL. INTR_CPUS is mapped to 'all_cpus'
by default. The idea is that INTR_CPUS should always return a valid set.
Device drivers which want to use per-CPU interrupts should start using
INTR_CPUS instead of simply assigning interrupts to all available CPUs.
In the future we may wish to add tunables to control the policy of
INTR_CPUS (e.g. should it be local-only or global, should it ignore
SMT threads or not).
The x86 nexus driver exposes the internal set of interrupt CPUs from the
the x86 interrupt code via INTR_CPUS.
The ACPI bus driver and PCI bridge drivers use _PXM to return a suitable
LOCAL_CPUS set when _PXM exists and DEVICE_NUMA is enabled. They also and
the global INTR_CPUS set from the nexus driver with the per-domain set from
_PXM to generate a local INTR_CPUS set for child devices.
Reviewed by: wblock (manpage)
Differential Revision: https://reviews.freebsd.org/D5519
Summary:
The Initial Local APIC ID is returned by CPUID function 1 (in EBX).
On AMD Family 10h systems the way that ID is built is controlled by
an MSR bit (InitApicIdCpuIdLo). BKDG instructs BIOS to set it in a
certain way, but a BIOS can be buggy. In that case the ID can confuse
tools that use it, e.g. hwloc.
For example, on a system that I own real Local APIC IDs are configured
as 0, 1, 2, 3, but IDs reported via CPUID.1 are 0, 0x40, 0x80, 0xc0.
See: https://github.com/open-mpi/hwloc/issues/183
Reviewed by: kib
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6060
rounddown2 tends to produce longer lines than the original code
and when the code has a high indentation level it was not really
advantageous to do the replacement.
This tries to strike a balance between readability using the macros
and flexibility of having the expressions, so not everything is
converted.
(And 4Kn minidump support, but only for amd64.)
Make sure all I/O to the dump device is of the native sector size. To
that end, we keep a native sector sized buffer associated with dump
devices (di->blockbuf) and use it to pad smaller objects as needed (e.g.
kerneldumpheader).
Add dump_write_pad() as a convenience API to dump smaller objects with
zero padding. (Rather than pull in NPM leftpad, we wrote our own.)
Savecore(1) has been updated to deal with these dumps. The format for
512-byte sector dumps should remain backwards compatible.
Minidumps for other architectures are left as an exercise for the
reader.
PR: 194279
Submitted by: ambrisko@
Reviewed by: cem (earlier version), rpokala
Tested by: rpokala (4Kn/512 except 512 fulldump), cem (512 fulldump)
Relnotes: yes
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D5848
Submitted by: Jun Su <junsu microsoft com>
Reviewed by: jhb, kib, sephe
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5910
doreti provides the common code path for returning from interrupt
andlers on x86. Exposing doreti as a global symbol allows kernel
modules to include low-level interrupt handlers instead of requiring
all low-level handlers to be statically compiled into the kernel.
Submitted by: Howard Su <howard0su@gmail.com>
Reviewed by: kib
Some BIOSes disable AMD Topology extension on AMD Family 15h notebook
processors. We re-enable the extension, so that we can properly discover
core and cache topology. Linux seems to do the same.
Reported by: Johannes Dieterich <dieterich.joh@gmail.com>
Reviewed by: jhb, kib
Tested by: Johannes Dieterich <dieterich.joh@gmail.com>
(earlier version)
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D5883
DTrace-related exceptions in userland code are handled elsewhere.
One practical problem was a crash in dtrace_invop_start() when saved
%rsp pointed to a virtual address that was not backed.
i386 code already ignored userland exceptions.
Reviewed by: markj, kib
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D5906
We're currently seeing how hard it would be to run CloudABI binaries on
operating systems cannot be modified easily (Windows, Mac OS X). The
idea is that we want to just run them without any sandboxing. Now
that CloudABI executables are PIE, this is already a bit easier, but TLS
is still problematic:
- CloudABI executables want to write to the %fs, which typically
requires extra system calls by the emulator every time it needs to
switch between CloudABI's and its own TLS.
- If CloudABI executables overwrite the %fs base unconditionally, it
also becomes harder for the emulator to store a backup of the old
value of %fs. To solve this, let's no longer overwrite %fs, but just
%fs:0.
As CloudABI's C library does not use a TCB, this space can now be used
by an emulator to keep track of its internal state. The executable can
now safely overwrite %fs:0, as long as it makes sure that the TCB is
copied over to the new TLS area.
Ensure that there is an initial TLS area set up when the process starts,
only containing a bogus TCB. We don't really care about its contents on
FreeBSD.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D5836
kern.features.linux: 1 meaning linux 32 bits binaries are supported
kern.features.linux64: 1 meaning linux 64 bits binaries are supported
The goal here is to help 3rd party applications (including ports) to determine
if the host do support linux emulation
Reviewed by: dchagin
MFC after: 1 week
Relnotes: yes
Differential Revision: D5830
- Set BI_CAN_EXEC_DYN, so we can execute ET_DYN ELF files in addition to
regular ET_EXECs.
- Provide an AT_BASE entry in the auxiliary vector, so the executable
knows at which address it got loaded and can apply relocations.
Simplify and unify placeholder type definitions.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D5771
This moves the enabling of interrupts slightly earlier (the old location
was still before devices were enumerated and probed) and does it in the
interrupt code (rather than in the device configuration code). This
also avoids tripping over an assertion on the first TLB shootdown with
earlier AP startup.
Reviewed by: kib
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D5710
during argument validity verification, unbound zero'ing of the process LDT
and adjacent memory can be initiated from usermode.
Submitted by: CORE Security
Patch by: kib
Security: SA-16:15
non-multiple of 64 bytes. Thereafter, the user state save area is
misaligned, which triggers assertion in the debugging kernels, or
segmentation violation on accesses for non-debugging configs.
Force the desired alignment of the user save area as the fix
(workaround is to disable bit 9 in the hw.xsave_mask loader tunable).
This correction is required for booting on the upcoming Intel' Purley
platform.
Reported and tested by: "Pieper, Jeffrey E" <jeffrey.e.pieper@intel.com>,
jimharris
Sponsored by: The FreeBSD Foundation
MFC after: 3 days
- Advertise the word size for CloudABI ABIs via the SV_LP64 flag. All of
the other ABIs include either SV_ILP32 or SV_LP64.
- Fix kdump to not assume a 32-bit ABI if the ABI flags field is non-zero
but SV_LP64 isn't set. Instead, only assume a 32-bit ABI if SV_ILP32 is
set and fallback to the unknown value of "00" if neither SV_LP64 nor
SV_ILP32 is set.
Reviewed by: kib, ed
Differential Revision: https://reviews.freebsd.org/D5560
need to include it explicitly when <vm/vm_param.h> is already included.
Suggested by: alc
Reviewed by: alc
Differential Revision: https://reviews.freebsd.org/D5379
POSIX requires these members to be of type void * rather than the
char * inherited from 4BSD. NetBSD and OpenBSD both changed their
fields to void * back in 1998. No new build failures were reported
via an exp-run.
PR: 206503 (exp-run)
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D5092
AT_SECURE auxv entry has been added to the Linux 2.5 kernel to pass a
boolean flag indicating whether secure mode should be enabled. 1 means
that the program has changes its credentials during the execution.
Being exported AT_SECURE used by glibc issetugid() call.
Submitted by: imp, dchagin
Security: FreeBSD-SA-16:10.linux
Security: CVE-2016-1883
registers. This brings amd64 on par with i386, providing consistent
initial FPU state.
Note that we do not clear any extended state, at least because kernel
does not understand extended state structure and consequences of zero
overwrite after fninit()/fpusave().
Submitted by: joss.upton@yahoo.com
PR: 206370
MFC after: 2 weeks
The set_robust_list system call request the kernel to record the head
of the list of robust futexes owned by the calling thread. The head
argument is the list head to record.
The get_robust_list system call should return the head of the robust
list of the thread whose thread id is specified in pid argument.
The list head should be stored in the location pointed to by head
argument.
In contrast, our implemenattion of get_robust_list system call copies
the known portion of memory pointed by recorded in set_robust_list
system call pointer to the head of the robust list to the location
pointed by head argument.
So, it is possible for a local attacker to read portions of kernel
memory, which may result in a privilege escalation.
Submitted by: mjg
Security: SA-16:03.linux
