MSI are implemented via Inbound Shared Doorbell 1 interrupts. Interrupts
are triggered by writing to Software Triggered Interrupt registeri (PCIe
card using physical address of this register in BAR0 space). There are 32
interrupts available. It can be increased by using Doorbell 2 and
Doorbell 3 registers to 96 interrupts.
Obtained from: Marvell, Semihalf
MSI are implemented via software interrupt. PCIe cards will write
into software interrupt register which will cause inbound shared
interrupt which will be interpreted as a MSI.
Obtained from: Marvell, Semihalf
- Add functions to calculate clocks instead using hardcoded values
- Update reset and timers functions
- Update number of interrupts
- Change name of platform from db88f78100 to db78460
- Correct DRAM size and PCI IRQ routing in dts file.
Obtained from: Semihalf
to this pmap.
Revise some comments.
The file vm/vm_param.h includes the file machine/vmparam.h, so there is no
need to directly include it.
Tested by: andrew
allocating them on the stack of various bus_dmamap_load*() functions. The
S/G lists are stored in the DMA tags. This matches the implementation on
all other platforms.
Discussed with: scottl, gibbs
Tested by: stas (arm@)
pmap_get_pv_entry(). In fact, some callers already held it around calls.
(In earlier versions, the same statements would apply to the page queues
lock.)
While I'm here tidy up the style of a few nearby statements and revise
some comments.
Tested by: Ian Lepore
o Disable multi-block operations: they sometimes fail.
o Don't use the PROOF bits yet: they hang the system hard.
o Disable the the multi-block operations for !rm9200, but it
still doesn't help.
o Fix writing < 12 bytes errata to actually work.
o Enable, for the moment, reporting extra bytes soaked up.
restructuring of the driver. I've tried to preserve the other silicon
workarounds that we've added over the years, but haven't had a chance
to extensively test on other hardware. On my AT91RM9200 with 30MHz/1
wire/64 block transfers, I've been able to go from ~.66MB/s to
2.25MB/s in the simple tests I performed, almost a 3.5x improvement.
This cuts the boot time almost in half when everything else goes
right (timed from rtc message to login: prompt).
PR: 155214
Submitted by: Ian Lapore
explicltly enable that. The driver chose to use 60MHz / 2 (30MHz)
most of the time rather than 60MHz / 4 (15MHz) based on the Linux
driver of the time. This pushes the spec a little in order to not
suffer the penalty of running at 15MHz. However, when other bus
masters are active in the system, and the user tries 4-wire mode, the
internal bus arbitration would fail with data loss as a result.
# Comments from PR were reworked to reflect my historical perspective
PR: 155214 (partial)
Submitted by: Ian Lepore
BUS_DMA_COHERENT attribute
The minimum unit for changing "cachable" attribute is page, so call
to pmap_change_attr effectively disable cache for all pages that newly
allocated DMA memory region spans on. The problem is that general-purpose
memory could reside on these pages too and disabling cache might affect
performance. Moreover ldrex/strex operators raise Data Abort exception
when accessing memory on page with "cachable" attribute off.
BUS_DMA_COHERENT does nto require memory to be coherent. It just suggests
to do best effort for reducing synchronization overhead.
frequencies. The maximum freqency is 100 kHz according to the datasheet.
- Add child device probing support based on the device tree. It now tries to
find i2c-address property in the tree and attach the device with given slave
address to iicbus.
Cummulative patch of changes that are not vendor-specific:
- ARMv6 and ARMv7 architecture support
- ARM SMP support
- VFP/Neon support
- ARM Generic Interrupt Controller driver
- Simplification of startup code for all platforms
ARM EABI the syscall value will be moved to a register to ease adding thumb
support. When this happens decoding of the instruction will no longer be
required.
to pull vm_param.h was removed. Other big dependency of vm_page.h on
vm_param.h are PA_LOCK* definitions, which are only needed for
in-kernel code, because modules use KBI-safe functions to lock the
pages.
Stop including vm_param.h into vm_page.h. Include vm_param.h
explicitely for the kernel code which needs it.
Suggested and reviewed by: alc
MFC after: 2 weeks
when running FreeBSD on QEMU emulating a Gumstix board.
While here remove the use of a magic number in the not-XScale version.
Pointed out by: kib
Reviewed by: stas
This is not strictly required with the current ABI but will be when we
switch to the ARM EABI. The aapcs requires the stack to be 4 byte aligned
at all times and 8 byte aligned when calling a public subroutine where the
current ABI only requires sp to be a multiple of 4.
off da0s1a instead of ate0. Note that MMC/SD is slot B. Until I
switch over to NAND boot, dataflash booting will preclude having SD
cards inserted at boot, so this last bit is untested.
My SAM9260-EK not boots to multi-user prompt.
Update i2c devices to just include the eeprom.
Update dataflash chip select to be CS 1 (this doesn't work yet and
needs changes to at91_spi and the spibus infrastructure).
Fix typo in comment.
FDT-enabled targets were broken after r238043 that relies
on device up the hierarchy to properly setup interrupt.
nexus device for ARM platforms did job only partially:
setting handler but not unmasking interrupt. Unmasking
was performed by platform code.
Reviewed by: andrew@
