Arm64 allows us to create execute only mappings. To make sure userspace is
unable to accidentally execute kernel code set the user execute never
bit in the kernel page tables.
MFC after: 1 week
Sponsored by: DARPA, AFRL
r351049 bogusly deleted these lines from files.amd64 but failed to add them to
files.x86. Since this works on i386, add them to files.x86 rather than just
adding them back to files.amd64.
PR: 240734
Reported by: Michael Pro
Summary:
ARM64 currently treats all data abort exceptions as page faults. This
can cause infinite loops on non-page fault faults, such as alignment faults.
Since kernel-side alignment faults should be avoided, this adds support directly
to the el0 fault handler, instead of the data_abort() handler.
Test Plan: Tested on rpi3, with a misaligned ldm test.
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D22133
I limited potentially infinite timings by 960 us based on a footnote on
page 38 of Maxim Integrated Application Note 937, Book of iButton
Standards: "In order not to mask interrupt signalling by other devices
on the 1–Wire bus, tRSTL + tR should always be less than 960 us."
MFC after: 3 weeks
Previously we used the minimal value of 1 us and it was really tight.
Application Note 3829 has a table describing recommended t_rec values
for various bus voltages, temperature conditions and numbers of slave
devices. The new value decreases the maximum possible data rate from
16.3 Kbit/s to 13.3 Kbit/s, but it allows for up to four slaves on a
3.3V bus (under room temperature).
References:
- Maxim Integrated Application Note 3829
Determining the Recovery Time for Multiple-Slave 1-Wire(R) Networks
- Maxim Integrated Application Note 937
Book of iButton Standards
Discussed with: imp (D22108)
MFC after: 3 weeks
We may want to mask exceptions when in userspace. This was previously
impossible as threads are created with all exceptions unmasked and
signals expected userspace to mask any. Fix these by copying the
mask state on thread creation and allow exceptions to be masked on
signal return, as long as they don't change.
Sponsored by: DARPA, AFRL
To allow consistent values to be used in both the kernel and userspace
create a function for these to be read from the kernel. They use a newly
created macro with the name of the ID register to read. For now there is
redundant information in the user_regs array as it still holds the CRm and
Op2 values, however this will be fixed in a later change.
This will be used by ptrace to allow hardware breakpoints in userspace.
Sponsored by: DARPA, AFRL
These instructions are used to access the registers described in armreg.h,
and will be used in a future change to create a per-register identification
macro.
Sponsored by: DARPA, AFRL
The debug monitor register state is now stored in a struct and updated
when required. Currently there is only a kernel state, however a
per-process state will be added in a future change.
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D22128
Previously we would call data_abort on all data and instruction aborts
however this is incorrect for most abort types. Move to use an array
of function pointers to allow for more handlers to be easily added.
Reviewed by: jhibbits
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D22170
Because of the previous naming scheme the old ID_AA64PFR0_EL1 macro
collided with a potential macro for the register of the same name. To fix
this collision rename these macros.
Sponsored by: DARPA, AFRL
The previous code came from OpenSolaris, which in my understanding require
allocation size to be known to free memory. To store that size previous
code allocated additional 8 byte header. But I have noticed that zlib
with present settings allocates 64KB context buffers for each call, that
could be efficiently cached by UMA, but addition of those 8 bytes makes
them fall back to physical RAM allocations, that cause huge overhead and
lock congestion on small blocks. Since FreeBSD's free() does not have
the size argument, switching to it solves the problem, increasing write
speed to ZVOLs with 4KB block size and GZIP compression on my 40-threads
test system from ~60MB/s to ~600MB/s.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
flag and use the same system.
This enables further fault locking improvements by allowing more faults to
proceed with a shared lock.
Reviewed by: kib
Tested by: pho
Differential Revision: https://reviews.freebsd.org/D22116
Certain consumers still need to guarantee a stable reference so we can not
switch entirely to atomics yet. Exclusive lock holders can still modify
and examine the refcount without using the ref api.
Reviewed by: kib
Tested by: pho
Sponsored by: Netflix, Intel
Differential Revision: https://reviews.freebsd.org/D21598
Recent changes to busy/valid/dirty have enabled page based synchronization
and the object lock is no longer required in many cases.
Reviewed by: kib
Sponsored by: Netflix, Intel
Differential Revision: https://reviews.freebsd.org/D21597
Declare retry in the function scope.
Rename it to retry as there is a timeout function which was
causing to code to compile.
Reported by: jhibbits
MFC after: 1 month
X-MFC-WITH: r354089
It turns out that a test of backtrace symbol resolution and formatting
requires symbols. Another option mightt be building with -rdynamic instead,
but this works for now.
Re-enabled skipped CI test, as it should now pass.
PR: 241562
Submitted by: lwhsu
Reported by: lwhsu
X-MFC-With: r354126, r354135, r354144
and IPv6. With IPv6 we may call if_addmulti() in context of processing
of an incoming packet. Usually this is interrupt context. While most
of the NIC drivers are able to reprogram multicast filters without
sleeping, some of them can't. An example is e1000 family of drivers.
With iflib conversion the problem was somewhat hidden. Iflib processes
packets in private taskqueue, so going to sleep doesn't trigger an
assertion. However, the sleep would block operation of the driver and
following incoming packets would fill the ring and eventually would
start being dropped. Enabling epoch for the full time of a packet
processing again started to trigger assertions for e1000.
Fix this problem once and for all using a general taskqueue to call
if_ioctl() method in all cases when if_addmulti() is called in a
non sleeping context. Note that nobody cares about returned value.
Reviewed by: hselasky, kib
Differential Revision: https://reviews.freebsd.org/D22154
Epoch itself doesn't rely on the counter and it is provided
merely for sleeping subsystems to check it.
- In functions that sleep use THREAD_CAN_SLEEP() to assert
correctness. With EPOCH_TRACE compiled print epoch info.
- _sleep() was a wrong place to put the assertion for epoch,
right place is sleepq_add(), as there ways to call the
latter bypassing _sleep().
- Do not increase td_no_sleeping in non-preemptible epochs.
The critical section would trigger all possible safeguards,
no sleeping counter is extraneous.
Reviewed by: kib
Revert rL349624 : Let TableGen write output only if it changed,
instead of doing so in cmake, attempt 2
Differential Revision: https://reviews.llvm.org/D55842
-----------------
As discussed on PR43385 this is causing Visual Studio msbuilds to
perpetually rebuild all tablegen generated files
Pull in r373664 from upstream llvm trunk (by Nico Weber):
Reland r349624: Let TableGen write output only if it changed, instead
of doing so in cmake
Move the write-if-changed logic behind a flag and don't pass it with
the MSVC generator. msbuild doesn't have a restat optimization, so
not doing write-if-change there doesn't have a cost, and it should
fix whatever causes PR43385.
This should fix the scenario where an incremental build from before
r353358 (the clang 9.0.0 upgrade) to r353358 or later fails to update
the timestamp of the generated lib/clang/headers/arm_fp16.h header.
After such a build, installing world from read-only source and object
directories would attempt to generate the header again, leading to
"clang-tblgen: error opening arm_fp16.h.d:Read-only file system".
Reported by: avg, np
PR: 241402
MFC after: 1 month
X-MFC-With: r353358
The source part of the review will be addressed in a different way.
Reviewed by: emaste, brooks
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D21492
Add lib/libzstd to _elftoolchain_libs
tools/build/Makefile needs to create the install dir for libzstd
Since this would make the line too long, rework to use a list
in one per line format (easier to add in future)
and dispense with the .for loop
Reviewed by: emaste bapt
Differential Revision: https://reviews.freebsd.org/D220134
After r353292, netmap generic adapter on if_vlan interfaces panics on
asserting the NET_EPOCH. In more detail, this happens when
nm_os_generic_xmit_frame() is called, that is in the generic txsync
routine.
Fix the issue by entering the NET_EPOCH during the generic txsync.
We amortize the cost of entering/exiting over a whole batch of
transmissions.
PR: 241489
Reported by: Aleksandr Fedorov <aleksandr.fedorov@itglobal.com>
The bogus requirement was causing CI infrastructure (which does not mount
procfs) to skip the test. Procfs has not been needed by libexecinfo on
FreeBSD (nor NetBSD) for years. Both now use a sysctl to obtain the path to
the current process image.
X-MFC-With: r354126
stderr:
Traceback (most recent call last):
File "/usr/tests/sys/netpfil/common/pft_ping.py", line 135, in <module>
main()
File "/usr/tests/sys/netpfil/common/pft_ping.py", line 124, in main
ping(args.sendif[0], args.to[0], args)
File "/usr/tests/sys/netpfil/common/pft_ping.py", line 74, in ping
raw = sp.raw(str(PAYLOAD_MAGIC))
File "/usr/local/lib/python3.6/site-packages/scapy/compat.py", line 52, in raw
return bytes(x)
TypeError: string argument without an encoding
MFC with: r354121
Sponsored by: The FreeBSD Foundation
In order to move python2 out of the test framework to avoid py2 vs. py3
confusions upgrade the remaining test cases using scapy to work with py3.
That means only one version of scapy needs to be installed in the CI system.
It also gives a path forward for testing i386 issues observed in the CI
system with some of these tests.
Fixes are:
- Use default python from environment (which is 3.x these days).
- properly ident some lines as common for the rest of the file to avoid
errors.
- cast the calculated offset to an int as the division result is considered
a float which is not accepted input.
- when comparing payload to a magic number make sure we always add the
payload properly to the packet and do not try to compare string in
the result but convert the data payload back into an integer.
- fix print formating.
Discussed with: lwhsu, kp (taking it off his todo :)
MFC after: 2 weeks
This patch modifies the zfs_ioc_snapshot_list_next() ioctl to enable it
to take input parameters that alter the way looping through the list of
snapshots is performed. The idea here is to restrict functions that
throw away some of the snapshots returned by the ioctl to a range of
snapshots that these functions actually use. This improves efficiency
and execution speed for some rollback and send operations.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#8077zfsonlinux/zfs@4c0883fb4a
MFC after: 2 weeks
