by amd64 and i386: For buffered writes we collect data and write it
out a ${DEV_BSIZE}-sized block at a time. The fragsz variable is used
to keep track of how much data we have collected in the buffer so far
and it's reset to zero immediately after writing a block to the dump
device.
When the last, possibly partially filled buffer is flushed, we didn't
reset fragsz to 0 and as such would stop reflecting reality. Since we
currently only need to do buffered writes once, this isn't a problem.
However, when kernel dumps are made by hand (say by callling doadump
from within DDB), the improperly cleared state from the first call to
dumpsys causes the next call to dumpsys to create an invalid code file.
This change resets fragsz after flushing the partially filled buffer so
that it fixes the two problems at once.
Approved by: re (scottl)
This is good enough to be able to run a RELENG_4 gdb binary against
a RELENG_4 application, along with various other tools (eg: 4.x gcore).
We use this at work.
ia32_reg.[ch]: handle the 32 bit register file format, used by ptrace,
procfs and core dumps.
procfs_*regs.c: vary the format of proc/XXX/*regs depending on the client
and target application.
procfs_map.c: Don't print a 64 bit value to 32 bit consumers, or their
sscanf fails. They expect an unsigned long.
imgact_elf.c: produce a valid 32 bit coredump for 32 bit apps.
sys_process.c: handle 32 bit consumers debugging 32 bit targets. Note
that 64 bit consumers can still debug 32 bit targets.
IA64 has got stubs for ia32_reg.c.
Known limitations: a 5.x/6.x gdb uses get/setcontext(), which isn't
implemented in the 32/64 wrapper yet. We also make a tiny patch to
gdb pacify it over conflicting formats of ld-elf.so.1.
Approved by: re
immediate is not saved by the architecture. Any of the break.{mifx}
instructions have their immediate saved in cr.iim on interruption.
Consequently, when we handle the break interrupt, we end up with a
break value of 0 when it was a break.b. The immediate is important
because it distinguishes between different uses of the break and
which are defined by the runtime specification.
The bottomline is that when the GNU debugger replaces a B-unit
instruction with a break instruction in the inferior, we would not
send the process a SIGTRAP when we encounter it, because the value
is not one we recognize as a debugger breakpoint.
This change adds logic to decode the bundle in which the break
instruction lives whenever the break value is 0. The assumption
being that it's a break.b and we fetch the immediate directly out
of the instruction. If the break instruction was not a break.b,
but any of break.{mifx} with an immediate of 0, we would be doing
unnecessary work. But since a break 0 is invalid, this is not a
problem and it will still result in a SIGILL being sent to the
process.
Approved by: re (scottl)
vm_page's machine-dependent fields. Use this function in
vm_pageq_add_new_page() so that the vm_page's machine-dependent and
machine-independent fields are initialized at the same time.
Remove code from pmap_init() for initializing the vm_page's
machine-dependent fields.
Remove stale comments from pmap_init().
Eliminate the Boolean variable pmap_initialized from the alpha, amd64,
i386, and ia64 pmap implementations. Its use is no longer required
because of the above changes and earlier changes that result in physical
memory that is being mapped at initialization time being mapped without
pv entries.
Tested by: cognet, kensmith, marcel
- Implement sampling modes and logging support in hwpmc(4).
- Separate MI and MD parts of hwpmc(4) and allow sharing of
PMC implementations across different architectures.
Add support for P4 (EMT64) style PMCs to the amd64 code.
- New pmcstat(8) options: -E (exit time counts) -W (counts
every context switch), -R (print log file).
- pmc(3) API changes, improve our ability to keep ABI compatibility
in the future. Add more 'alias' names for commonly used events.
- bug fixes & documentation.
in other codes. Add cpu_set_user_tls, use it to tweak user register
and setup user TLS. I ever wanted to merge it into cpu_set_kse_upcall,
but since cpu_set_kse_upcall is also used by M:N threads which may
not need this feature, so I wrote a separated cpu_set_user_tls.
o Remove the clock interface. Not only does it conflict with the MI
version when device genclock is added to the kernel, it was also
not possible to have more than 1 clock device. This of course would
have been a problem if we actually had more than 1 clock device.
In short: we don't need a clock interface and if we do eventually,
we should be using the MI one.
o Rewrite inittodr() and resettodr() to take into account that:
1) We use the EFI interface directly.
2) time_t is 64-bit and we do need to make sure we can determine
leap years from year 2100 and on. Add a nice explanation of
where leap years come from and why.
3) This rewrite happened in 2005 so any date prior to 1/1/2005
(either M/D/Y or D/M/Y) is bogus. Reprogram the EFI clock with
1/1/2005 in that case.
4) The EFI clock has a high probability of being correct, so
only (further) correct the EFI clock when the file system time
is larger. That should never happen in a time-synchronised world.
Complain when EFI lost 2 days or more.
Replace the copyright notice now that I (pretty much) rewrote all of
this file.
into _bus.h to help with name space polution from including all of bus.h.
In a few days, I'll commit changes to the MI code to take advantage of thse
sepration (after I've made sure that these changes don't break anything in
the main tree, I've tested in my trees, but you never know...).
Suggested by: bde (in 2002 or 2003 I think)
Reviewed in principle by: jhb
unw_step(). Both errors denote the end of a stack trace (i.e. no
prior frame), but are otherwise not error conditions.
Have db_trace() return 0 when the trace ends due to one of these
return codes as they are really normal termination conditions.
This change especially improves the output of the "show thread"
command in DDB when there are threads in fork_trampoline() and
previously db_trace() would return an error, causing the show
command to emit '***'.
MCA state requires a spin lock, which requires a valid curthread.
This change allows SMP kernels to boot into multi-user again.
While here, update the copyright notice and use __FBSDID for the
revision string.
1 Move the debug.clock_adjust_* sysctls to debug.clock.adjust_* to
make it easier to get only the clock statistics.
2 Make the sysctls read-only [suggested by Marius].
3 When determining the new clock adjustment, we checked for an error
either larger than 12.5% or smaller than 12.5%. We left out an error
of exactly 12.5%. For errors larger than 12.5% we adjust the clock
reload value in such a way that the next clock interrupt would be
early (as in premature). For errors less than 12.5% we stopped the
adjustment.
The current algorithm doesn't benefit from excluding an error of
exactly 12.5%. Change the code to stop adjusting the clock if the
error is *not* larger than 12.5% [suggested by Marius].
Discussed with: marius@
critical_enter() and critical_exit() are now solely a mechanism for
deferring kernel preemptions. They no longer have any affect on
interrupts. This means that standalone critical sections are now very
cheap as they are simply unlocked integer increments and decrements for the
common case.
Spin mutexes now use a separate KPI implemented in MD code: spinlock_enter()
and spinlock_exit(). This KPI is responsible for providing whatever MD
guarantees are needed to ensure that a thread holding a spin lock won't
be preempted by any other code that will try to lock the same lock. For
now all archs continue to block interrupts in a "spinlock section" as they
did formerly in all critical sections. Note that I've also taken this
opportunity to push a few things into MD code rather than MI. For example,
critical_fork_exit() no longer exists. Instead, MD code ensures that new
threads have the correct state when they are created. Also, we no longer
try to fixup the idlethreads for APs in MI code. Instead, each arch sets
the initial curthread and adjusts the state of the idle thread it borrows
in order to perform the initial context switch.
This change is largely a big NOP, but the cleaner separation it provides
will allow for more efficient alternative locking schemes in other parts
of the kernel (bare critical sections rather than per-CPU spin mutexes
for per-CPU data for example).
Reviewed by: grehan, cognet, arch@, others
Tested on: i386, alpha, sparc64, powerpc, arm, possibly more
FreeBSD based on aue(4) it was picked by OpenBSD, then from OpenBSD ported
to NetBSD and finally NetBSD version merged with original one goes into
FreeBSD.
Obtained from: http://www.gank.org/freebsd/cdce/
NetBSD
OpenBSD
This is mentioned in the Handbook but it is not as obvious to new
users why bpf is needed compared to the other largely self-explanatory
items in GENERIC.
PR: conf/40855
MFC after: 1 week
sys/bus_dma.h instead of being copied in every single arch. This slightly
reorders a flag that was specific to AXP and thus changes the ABI there.
The interface still relies on bus_space definitions found in <machine/bus.h>
so it cannot be included on its own yet, but that will be fixed at a later
date. Add an MD <machine/bus_dma.h> for ever arch for consistency and to
allow for future MD augmentation of the API. sparc64 makes heavy use of
this right now due to its different bus_dma implemenation.
place.
This moves the dependency on GCC's and other compiler's features into
the central sys/cdefs.h file, while the individual source files can
then refer to #ifdef __COMPILER_FEATURE_FOO where they by now used to
refer to #if __GNUC__ > 3.1415 && __BARC__ <= 42.
By now, GCC and ICC (the Intel compiler) have been actively tested on
IA32 platforms by netchild. Extension to other compilers is supposed
to be possible, of course.
Submitted by: netchild
Reviewed by: various developers on arch@, some time ago
We need to be able to test for the (possible) non-existence of the
FPSWA code.
PR: ia64/77591
Submitted by: Christian Kandeler (christian dot kandeler at hob dot de)
MFC after: 1 day
uses the i8237 without trying to emulate the PC architecture move
the register definitions for the i8237 chip into the central include
file for the chip, except for the PC98 case which is magic.
Add new isa_dmatc() function which tells us as cheaply as possible
if the terminal count has been reached for a given channel.
the last action of kern_exit(). Instead, it is a MD callout to cleanup
per-process state during exit.
- Add notes of concern to Alpha and ia64 about the possible need to drop
fp state in cpu_thread_exit() rather than in cpu_exit() since it is
per-thread state rather than per-process.
o implement double-extended and single precision loads and stores,
o implement double precision stores,
o replace the machdep.unaligned_print sysctl with debug.unaligned_print
and change the default value to 0,
o replace the machdep.unaligned_sigbus sysctl with debug.unaligned_test,
o Remmove the fillfd() function. The function is trvial enough for
inline assembly.
The debug.unaligned_test sysctl is used to test the emulation of
misaligned loads and stores. When PSR.ac is 0, the CPU will handle
misaligned memory accesses itselfi and we don't get an exception
for it. When PSR.ac is 1, the process needs to be signalled and we
should not emulate. The sysctl takes effect when PSR.ac is 1 and
tells us that we should emulate and not send a signal.
PR: 72268
MFC after: 1 week
on entry and it assumes the responsibility for releasing the page queues
lock if it must sleep.
Remove a bogus comment from pmap_enter_quick().
Using the first change, modify vm_map_pmap_enter() so that the page queues
lock is acquired and released once, rather than each time that a page
is mapped.
In such cases, the busying of the page and the unlocking of the
containing object by vm_map_pmap_enter() and vm_fault_prefault() is
unnecessary overhead. To eliminate this overhead, this change
modifies pmap_enter_quick() so that it expects the object to be locked
on entry and it assumes the responsibility for busying the page and
unlocking the object if it must sleep. Note: alpha, amd64, i386 and
ia64 are the only implementations optimized by this change; arm,
powerpc, and sparc64 still conservatively busy the page and unlock the
object within every pmap_enter_quick() call.
Additionally, this change is the first case where we synchronize
access to the page's PG_BUSY flag and busy field using the containing
object's lock rather than the global page queues lock. (Modifications
to the page's PG_BUSY flag and busy field have asserted both locks for
several weeks, enabling an incremental transition.)
"vm_fault: fault on nofault entry, addr: %lx" panic. The problem was a
stale PTE in the TLB that marked the page as not present, even though
we had a good PTE in the VHPT. We typically don't yet insert PTEs in
the TLB. We do that lazily. The CPU will look for the PTE in the VHPT
when there's no PTE in the TLB. Unfortunately this doesn't handle the
case of the stale PTE in the TLB. The quick fix is to invalidate the
TLB (sloppily) when the VHPT doesn't contain a valid PTE. This is also
the only case that may cause a PTE in the TLB that marks a page as
non-present.
specified register, but a pointer to the in-memory representation of
that value. The reason for this is twofold:
1. Not all registers can be represented by a register_t. In particular
FP registers fall in that category. Passing the new register value
by reference instead of by value makes this point moot.
2. When we receive a G or P packet, both are for writing a register,
the packet will have the register value in target-byte order and
in the memory representation (modulo the fact that bytes are sent
as 2 printable hexadecimal numbers of course). We only need to
decode the packet to have a pointer to the register value.
This change fixes the bug of extracting the register value of the P
packet as a hexadecimal number instead of as a bit array. The quick
(and dirty) fix to bswap the register value in gdb_cpu_setreg() as
it has been added on i386 and amd64 can therefore be removed and has
in fact been that.
Tested on: alpha, amd64, i386, ia64, sparc64
o Remove a bogus comment that relates to alpha.
o s/u_int64_t/uint64_t/g
o Add bi_spare2 to make the internal padding explicit.
o Move BOOTINFO_MAGIC after the field it applies to.
table with console settings, we now only need to know at which
address the UART lives. Leaving the baudrate unspecified results
in us using the baudrate at which the UART operates. This removes
one parameter that can interfere with a successful installation
out of the box.
control the number of lines per page rather than a constant. The variable
can be examined and changed in ddb as '$lines'. Setting the variable to
0 will effectively turn off paging.
- Change db_putchar() to force out pending whitespace before outputting
newlines and carriage returns so that one can rub out content on the
current line via '\r \r' type strings.
- Change the simple pager to rub out the --More-- prompt explicitly when
the routine exits.
- Add some aliases to the simple pager to make it more compatible with
more(1): 'e' and 'j' do a single line. 'd' does half a page, and
'f' does a full page.
MFC after: 1 month
Inspired by: kris
modes on a tty structure.
Both the ".init" and the current settings are initialized allowing
the function to be used both at attach and open time.
The function takes an argument to decide if echoing should be enabled.
Echoing should not be enabled for regular physical serial ports
unless they are consoles, in which case they should be configured
by ttyconsolemode() instead.
Use the new function throughout.
need to mask off the page offset bits. (This operation made some sense
prior to i386/i386/pmap.c revision 1.254 when we passed a physical address
rather than a vm_page pointer to pmap_enter().)
uses predate the change in the pmap_enter() interface that replaced the
page's physical address by the address of its vm_page structure. The
PHYS_TO_VM_PAGE() was being used to compute the address of the same vm_page
structure that was being passed in.
old or previous value instead of void. This is not as is documented
in atomic(9), but is API (and ABI) compatible and simply makes sense.
This feature will primarily be used for atomic PTE updates in PMAP/ng.
a stack trace from ddb, the output will pause with a '--More--' prompt
every 18 lines. If you hit Enter, it will print another line and prompt
again. If you hit space it will output another page and then prompt.
If you hit 'q' or 'x' it will abort the rest of the stack trace.
- Fix the sparc64 userland stack trace to honor the total count of lines
to print. This is useful if your trace happens to walk back onto
0xdeadc0de and gets stuck in an endless loop.
MFC after: 1 month
Tested on: i386, alpha, sparc64
Completely remove the remaining EFI includes and add our own (type)
definitions instead. While here, abstract more of the internals by
providing interface functions.
EFI headers and put them all in <machine/fpu.h>. The Intel EFI headers
conflict with the Intel ACPI headers (duplicate type definitions), so
are being phased out in the kernel.
and which takes a M_WAITOK/M_NOWAIT flag argument.
Add compatibility isa_dmainit() macro which whines loudly if
isa_dma_init() fails.
Problem uncovered by: tegge
and was propagated to nearly every platform. The boundary of the child needs
to consider the boundary of the parent and pick the minimum of the two, not
the maximum. However, if either is 0 then pick the appropriate one.
This bug was exposed by a recent change to ATA, which should now be fixed by
this change. The alignment and maxsegsz tag attributes likely also need
a similar review in the near future.
This is a MT5 candidate.
Reviewed by: marcel
Submitted by: sos (in part)
the alignment and boundary constraints are being respected, which
fixes the reported ATA problems with SiI chips.
I consider the busdma implementation worrisome nonetheless. Not
only is there too much MI code duplicated in MD files, there's a
lot of questionable code. I smell a wholesale, cross-platform
overhaul coming...
MT5 candidate.
but with slightly cleaned up interfaces.
The KSE structure has become the same as the "per thread scheduler
private data" structure. In order to not make the diffs too great
one is #defined as the other at this time.
The KSE (or td_sched) structure is now allocated per thread and has no
allocation code of its own.
Concurrency for a KSEGRP is now kept track of via a simple pair of counters
rather than using KSE structures as tokens.
Since the KSE structure is different in each scheduler, kern_switch.c
is now included at the end of each scheduler. Nothing outside the
scheduler knows the contents of the KSE (aka td_sched) structure.
The fields in the ksegrp structure that are to do with the scheduler's
queueing mechanisms are now moved to the kg_sched structure.
(per ksegrp scheduler private data structure). In other words how the
scheduler queues and keeps track of threads is no-one's business except
the scheduler's. This should allow people to write experimental
schedulers with completely different internal structuring.
A scheduler call sched_set_concurrency(kg, N) has been added that
notifies teh scheduler that no more than N threads from that ksegrp
should be allowed to be on concurrently scheduled. This is also
used to enforce 'fainess' at this time so that a ksegrp with
10000 threads can not swamp a the run queue and force out a process
with 1 thread, since the current code will not set the concurrency above
NCPU, and both schedulers will not allow more than that many
onto the system run queue at a time. Each scheduler should eventualy develop
their own methods to do this now that they are effectively separated.
Rejig libthr's kernel interface to follow the same code paths as
linkse for scope system threads. This has slightly hurt libthr's performance
but I will work to recover as much of it as I can.
Thread exit code has been cleaned up greatly.
exit and exec code now transitions a process back to
'standard non-threaded mode' before taking the next step.
Reviewed by: scottl, peter
MFC after: 1 week
The removed argument could trivially be derived from the remaining one.
That in turn should be the same as curthread, but it is possible that curthread could be expensive to derive on some syste,s so leave it as an argument.
Having both proc and thread as an argumen tjust gives an opportunity for
them to get out sync.
MFC after: 3 days
in diagnostics. It has outlived its usefulness and has started
causing panics for people who turn on DIAGNOSTIC, in what is otherwise
good code.
MFC after: 2 days
these two reasons:
1. On ia64 a function pointer does not hold the address of the first
instruction of a functions implementation. It holds the address
of a function descriptor. Hence the user(), btrap(), eintr() and
bintr() prototypes are wrong for getting the actual code address.
2. The logic forces interrupt, trap and exception entry points to
be layed-out contiguously. This can not be achieved on ia64 and is
generally just bad programming.
The MCOUNT_FROMPC_USER macro is used to set the frompc argument to
some kernel address which represents any frompc that falls outside
the kernel text range. The macro can expand to ~0U to bail out in
that case.
The MCOUNT_FROMPC_INTR macro is used to set the frompc argument to
some kernel address to represent a call to a trap or interrupt
handler. This to avoid that the trap or interrupt handler appear to
be called from everywhere in the call graph. The macro can expand
to ~0U to prevent adjusting frompc. Note that the argument is selfpc,
not frompc.
This commit defines the macros on all architectures equivalently to
the original code in sys/libkern/mcount.c. People can take it from
here...
Compile-tested on: alpha, amd64, i386, ia64 and sparc64
Boot-tested on: i386
valid pmap to the pmap functions that require one. Remove the checks for
NULL. (These checks have their origins in the Mach pmap.c that was
integrated into BSD. None of the new code written specifically for
FreeBSD included them.)
compile option. All FreeBSD packet filters now use the PFIL_HOOKS API and
thus it becomes a standard part of the network stack.
If no hooks are connected the entire packet filter hooks section and related
activities are jumped over. This removes any performance impact if no hooks
are active.
Both OpenBSD and DragonFlyBSD have integrated PFIL_HOOKS permanently as well.
of the MCOUNT_ENTER, MCOUNT_EXIT and MCOUNT_DECL defines. Also make
sure there's a prototype of _MCOUNT_DECL(). This allows us to build
a kernel. There are still unresolved symbols, so linking fails.
_mcount() stub when profiling is enabled. Emit this code sequence
for assembly routines as welli (MCOUNT definition in <machine/asm.h>.
We do not pass the GOT entry however as the 4th argument, because it's
not used. The _mcount() stub calls __mcount(), which does the actual
work. Define _MCOUNT_DECL to define __mcount. We do not have an
implementation of mcount(), so we define MCOUNT as empty, but have a
weak alias to _mcount() in _mcount.S.
Note that the _mcount() stub in the kernel is slightly different from
the stub in userland. This is because we do not have to worry about
nested routines in the kernel.
have been rush hour...
While here, move COMPAT_IA32 from opt_global.h to opt_compat.h like on
amd64. Consequently, it's unsafe to use the option in pcb.h. We now
unconditionally have the ia32 specific registers in the PCB.
This commit is untested.
we update the registers. That way we don't have any dirty registers to
worry about and also know that bsp=bspstore, which makes updating the
RSE related registers predictable.
This is not the end of it. We need more validity checks, but for now
this allows us to complete the gdb testsuite without crashing the
kernel.
to allow dumping per-thread machine specific notes. On ia64 we use this
function to flush the dirty registers onto the backingstore before we
write out the PRSTATUS notes.
Tested on: alpha, amd64, i386, ia64 & sparc64
Not tested on: arm, powerpc
The hardware always gives read access for privilege level 0, which
means that we cannot use the hardware access rights and privilege
level in the PTE to test whether there's a change in protection. So,
we save the original vm_prot_t in the PTE as well.
Add pmap_pte_prot() to set the proper access rights and privilege
level on the PTE given a pmap and the requested protection.
The above allows us to compare the protection in pmap_extract_and_hold()
which was missing. While in pmap_extract_and_hold(), add pmap locking.
While here, clean up most (i.e. all but one) PTE macros we inherited
from alpha. They were either unused, used inconsistently, badly named
or simply weren't beneficial. We save the wired and managed state of
the PTE in distinct (bit) fields.
While in pte.h, s/u_int64_t/uint64_t/g
pmap locking obtained from: alc@
feedback & review by: alc@
path. The basic problem is that we cannot set the single stepping flag
directly, because we don't leave the kernel via an interrupt return. So,
we need another way to set the single stepping flag.
The way we do this is by enabling the lower-privilege transfer trap, which
gets raised when we drop the privilege level. However, since we're still
running in kernel space (sec), we're not yet done. We clear the lower-
privilege transfer trap, enable the taken-branch trap and continue exiting
the kernel until we branch into user space.
Given the current code, there's a total of two traps this way before
we can raise SIGTRAP.
after a fork(2) in fork_trampoline(). By moving the epc_syscall_return
label immediately before the call to do_ast() in epc_syscall(), we not
only achieve that but also handle the detour through exception_return
when the frame corresponds to an asynchronous kernel entry. Hence, we
simplified fork_trampoline() as a side-effect.
related to breakpoints and single stepping into SIGTRAP so gdb(1) knows
why the remote target has stopped. In particular, gdb(1) needs to know
if the reason is something of its own doing.
text/data are covered on APs. This enables the kernel to boot on
a 4 way Intel Itanium-2 platform. This has a secondary effect of
keeping the TRs identical on BP and the APs.
reviewed by: marcel@
being defined, define and use a new MD macro, cpu_spinwait(). It only
expands to something on i386 and amd64, so the compiled code should be
identical.
Name of the macro found by: jhb
Reviewed by: jhb
their own directory and module, leaving the MD parts in the MD
area (the MD parts _are_ part of the modules). /dev/mem and /dev/io
are now loadable modules, thus taking us one step further towards
a kernel created entirely out of modules. Of course, there is nothing
preventing the kernel from having these statically compiled.
brings ia64 to parity with alpha, amd64, and i386 in this area.)
- Prevent a race in pmap_find_pte(): If pmap_find_pte() sleeps in
uma_zalloc(), another thread could allocate a pte at the same address.
Instead, sleep at a higher level and retry the lookup before retrying
the allocation.
Reviewed and tested by: marcel@
dereference curthread. It is called only from critical_{enter,exit}(),
which already dereferences curthread. This doesn't seem to affect SMP
performance in my benchmarks, but improves MySQL transaction throughput
by about 1% on UP on my Xeon.
Head nodding: jhb, bmilekic
the thread ID and call db_trace_thread().
Since arm has all the logic in db_stack_trace_cmd(), rename the
new DB_COMMAND function to db_stack_trace to avoid conflicts on
arm.
While here, have db_stack_trace parse its own arguments so that
we can use a more natural radix for IDs. If the ID is not a thread
ID, or more precisely when no thread exists with the ID, try if
there's a process with that ID and return the first thread in it.
This makes it easier to print stack traces from the ps output.
requested by: rwatson@
tested on: amd64, i386, ia64
future:
rename ttyopen() -> tty_open() and ttyclose() -> tty_close().
We need the ttyopen() and ttyclose() for the new generic cdevsw
functions for tty devices in order to have consistent naming.
pmap_protect() and pmap_remove(). In general, they require the lock in
order to modify a page's pv list or flags. In some cases, however,
pmap_protect() can avoid acquiring the lock.
pmap_remove_pages(). (The implementation of pmap_remove_pages() is
optional. If pmap_remove_pages() is unimplemented, the acquisition and
release of the page queues lock is unnecessary.)
Remove spl calls from the alpha, arm, and ia64 pmap_remove_pages().
Most of the changes are a direct result of adding thread awareness.
Typically, DDB_REGS is gone. All registers are taken from the
trapframe and backtraces use the PCB based contexts. DDB_REGS was
defined to be a trapframe on all platforms anyway.
Thread awareness introduces the following new commands:
thread X switch to thread X (where X is the TID),
show threads list all threads.
The backtrace code has been made more flexible so that one can
create backtraces for any thread by giving the thread ID as an
argument to trace.
With this change, ia64 has support for breakpoints.
o ksym_start and ksym_end changed type to vm_offset_t.
o Make debugging support conditional upon KDB instead of DDB.
o Call kdb_enter() instead of breakpoint().
o Remove implementation of Debugger().
o Call kdb_trap() according to the new world order.
unwinder:
o s/db_active/kdb_active/g
o Various s/ddb/kdb/g
o Add support for unwinding from the PCB as well as the trapframe.
Abuse a spare field in the special register set to flag whether
the PCB was actually constructed from a trapframe so that we can
make the necessary adjustments.
md_var.h:
o Add RSE convenience macros.
o Add ia64_bsp_adjust() to add or subtract from BSP while taking
NaT collections into account.
a PCB from a trapframe for purposes of unwinding the stack. The PCB
is used as the thread context and all but the thread that entered the
debugger has a valid PCB.
This function can also be used to create a context for the threads
running on the CPUs that have been stopped when the debugger got
entered. This however is not done at the time of this commit.
in which multiple (presumably different) debugger backends can be
configured and which provides basic services to those backends.
Besides providing services to backends, it also serves as the single
point of contact for any and all code that wants to make use of the
debugger functions, such as entering the debugger or handling of the
alternate break sequence. For this purpose, the frontend has been
made non-optional.
All debugger requests are forwarded or handed over to the current
backend, if applicable. Selection of the current backend is done by
the debug.kdb.current sysctl. A list of configured backends can be
obtained with the debug.kdb.available sysctl. One can enter the
debugger by writing to the debug.kdb.enter sysctl.
backend improves over the old GDB support in the following ways:
o Unified implementation with minimal MD code.
o A simple interface for devices to register themselves as debug
ports, ala consoles.
o Compression by using run-length encoding.
o Implements GDB threading support.
bootp -> BOOTP
bootp.nfsroot -> BOOTP_NFSROOT
bootp.nfsv3 -> BOOTP_NFSV3
bootp.compat -> BOOTP_COMPAT
bootp.wired_to -> BOOTP_WIRED_TO
- i.e. back out the previous commit. It's already possible to
pxeboot(8) with a GENERIC kernel.
Pointed out by: dwmalone
has outlined which break numbers are software interrupts, debugger
breakpoints and ABI specific breaks. We mostly treated all break
numbers we didn't care about as debugger breakpoints.
BOOTP -> bootp
BOOTP_NFSROOT -> bootp.nfsroot
BOOTP_NFSV3 -> bootp.nfsv3
BOOTP_COMPAT -> bootp.compat
BOOTP_WIRED_TO -> bootp.wired_to
This lets you PXE boot with a GENERIC kernel by putting this sort of thing
in loader.conf:
bootp="YES"
bootp.nfsroot="YES"
bootp.nfsv3="YES"
bootp.wired_to="bge1"
or even setting the variables manually from the OK prompt.
than as one-off hacks in various other parts of the kernel:
- Add a function maybe_preempt() that is called from sched_add() to
determine if a thread about to be added to a run queue should be
preempted to directly. If it is not safe to preempt or if the new
thread does not have a high enough priority, then the function returns
false and sched_add() adds the thread to the run queue. If the thread
should be preempted to but the current thread is in a nested critical
section, then the flag TDF_OWEPREEMPT is set and the thread is added
to the run queue. Otherwise, mi_switch() is called immediately and the
thread is never added to the run queue since it is switch to directly.
When exiting an outermost critical section, if TDF_OWEPREEMPT is set,
then clear it and call mi_switch() to perform the deferred preemption.
- Remove explicit preemption from ithread_schedule() as calling
setrunqueue() now does all the correct work. This also removes the
do_switch argument from ithread_schedule().
- Do not use the manual preemption code in mtx_unlock if the architecture
supports native preemption.
- Don't call mi_switch() in a loop during shutdown to give ithreads a
chance to run if the architecture supports native preemption since
the ithreads will just preempt DELAY().
- Don't call mi_switch() from the page zeroing idle thread for
architectures that support native preemption as it is unnecessary.
- Native preemption is enabled on the same archs that supported ithread
preemption, namely alpha, i386, and amd64.
This change should largely be a NOP for the default case as committed
except that we will do fewer context switches in a few cases and will
avoid the run queues completely when preempting.
Approved by: scottl (with his re@ hat)
to <sys/gmon.h>. Cleaned them up a little by not attempting to ifdef
for incomplete and out of date support for GUPROF in userland, as in
the sparc64 version.
remove the empty line between the fdc and sio devices. The empty
line suggests that the comment applies to fdc only while it applies
to all following devices and options.
Typo spotted by: ru@
gets the relocation base passed in relocbase, we cannot declare a
local variable with the same name. Assume the argument holds the
same value as the local variable did...
elf_reloc() backends for two reasons. First, to support the possibility
of there being two elf linkers in the kernel (eg: amd64), and second, to
pass the relocbase explicitly (for relocating .o format kld files).
the kernel. We can guarantee this by resetting the FP status register.
This masks all FP traps. The reason we did get FP traps was that we
didn't reset the FP status register in all cases.
Make sure to reset the FP status register in syscall(). This is one of
the places where it was forgotten.
While on the subject, reset the FP status register only when we trapped
from user space.
individual asm versions. The global lock is shared between the BIOS and
OS and thus cannot use our mutexes. It is defined in section 5.2.9.1 of
the ACPI specification.
Reviewed by: marcel, bde, jhb
o Fix and improve comments and references,
o Add PFIL_HOOKS, UFS_ACL and UFS_DIRHASH,
o Switch from SCHED_4BSD to SCHED_ULE,
o Remove SCSI_DELAY (there's no SCSI support),
move its declaration to the machine-dependent header file on those
machines that use it. In principle, only i386 should have it.
Alpha and AMD64 should use their direct virtual-to-physical mapping.
- Remove pmap_kenter_temporary() from ia64. It is unused. Approved
by: marcel@
distinguish between debugger inserted breakpoints and fixed
breakpoints. While here, make sure the break instruction never
ends up in the last slot of a bundle by forcing it to be an
M-unit instruction. This makes it easier for use to skip over
it.
level of abstraction for any and all CPU mask and CPU bitmap variables
so that platforms have the ability to break free from the hard limit
of 32 CPUs, simply because we don't have more bits in an u_int. Note
that the type is not supposed to solve massive parallelism, where
the number of CPUs can be larger than the width of the widest integral
type. As such, cpumask_t is not supposed to be a compound type. If
such would be necessary in the future, we can deal with the issues
then and there. For now, it can be assumed that the type is integral
and unsigned.
With this commit, all MD definitions start off as u_int. This allows
us to phase-in cpumask_t at our leasure without breaking anything.
Once cpumask_t is used consistently, platforms can switch to wider
(or smaller) types if such would be beneficial (or not; whatever :-)
Compile-tested on: i386
for uart(4) to figure out which device to use as console. Use this file
to define hw.uart.console instead so that we don't have to put it in
the default loader.conf, which makes it hard to override.
dependent function by the same name and a machine-independent function,
sf_buf_mext(). Aside from the virtue of making more of the code machine-
independent, this change also makes the interface more logical. Before,
sf_buf_free() did more than simply undo an sf_buf_alloc(); it also
unwired and if necessary freed the page. That is now the purpose of
sf_buf_mext(). Thus, sf_buf_alloc() and sf_buf_free() can now be used
as a general-purpose emphemeral map cache.
based on the Madison core and targeting the low end of the spectrum.
Its clock frequency is 1Ghz, whereas Madison starts at 1.3Ghz. Since
the CPUID information is the same for Madison and Deerfield, we use
the clock frequency to identify the processor.
Supposedly the Deerfield only uses 62W, which seems to be less than
modern Xeon processors (about 70W) and about half what a Madison would
need.
ever since alpha/alpha/pmap.c revision 1.81 introduced the list allpmaps,
there has been no reason for having this function on Alpha. Briefly,
when pmap_growkernel() relied upon the list of all processes to find and
update the various pmaps to reflect a growth in the kernel's valid
address space, pmap_init2() served to avoid a race between pmap
initialization and pmap_growkernel(). Specifically, pmap_pinit2() was
responsible for initializing the kernel portions of the pmap and
pmap_pinit2() was called after the process structure contained a pointer
to the new pmap for use by pmap_growkernel(). Thus, an update to the
kernel's address space might be applied to the new pmap unnecessarily,
but an update would never be lost.
