ISR that are normally clear. RST is one, though in some overflow cases
it can be set. RDC is only set when a remote DMA is finished from the
memory mapped memory to the transmit rings, which we poll fore in the
code with ED_LOCK around the operation that would set it.
KVM clock shares the same data structures between the guest and the host
as Xen so it makes sense to just have a single copy of this code.
Differential Revision: https://reviews.freebsd.org/D1429
Reviewed by: royger (eariler version)
MFC after: 1 month
we also know that it "can't fail" given the single-threaded nature of
device enumeration. Go ahead and check it just in case, but add a
comment.
CID: 1009393
Sponsored by: Netflix, Inc
Fixed upstream in Linux commit 7ff0ebcc1e30e3216c8c62ee71f59ac830b10364
Differential Revision: https://reviews.freebsd.org/D1762
Reviewed by: hselasky, kib
Sponsored by: The FreeBSD Foundation
allocations if only one element should be allocated per page
cache. Make one allocation per element compile time configurable. Fix
a comment while at it.
Suggested by: ian @
MFC after: 1 week
that we should use a normal-TRB if there are more TRBs extending the
data-stage TRB. Add a dedicated state bit to the internal USB transfer
flags to handle this case.
Reported by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
MFC after: 1 week
In 10.1-RELEASE the default number of MSI vectors used was changed from one
to as many vectors as the HW supports.
This change resulted in an ahci timeouts regression when running on AMD
SB7x0/SB8x0/SB9x0 hardware, so its now limited to 1 MSI by default using
this new quirk.
MFC after: 2 weeks
Sponsored by: Multiplay
controller.
The gpiobus is responsible to keep track of the used pins and serialize
the access to pins.
Some of these features are important to devices that do not descend
directly from gpiobus and as such cannot make use of its features (one
classic example is gpioc that is attached to the GPIO controller and could
not, until now, make use of the gpiobus locking).
this codepath.)
(1<<30) is documented as BLM_PCH_OVERRIDE_ENABLE, which the current
i915 driver in Linux only sets for broadwell chips.
This fixes the backlight control on the Lenovo X230.
Approved by: kib
Obtained from: Linux 7aa1e7f06d6ea1bce3b27630d50769d13da28b1a
Add separate software Tx queue limit for non-TCP traffic to make total
limit higher and avoid local drops of TCP packets because of no
backpressure.
There is no point to make non-TCP limit high since without backpressure
UDP stream easily overflows any sensible limit.
Split early drops statistics since it is better to have separate counter
for each drop reason to make it unabmiguous.
Add software Tx queue high watermark. The information is very useful to
understand how big queues grow under traffic load.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Most likely is was just memory leak on the error handling path since
typically efsys_mem_t is filled in by zeros on allocation.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
sfxge_dma_alloc() calls bus_dmamem_alloc() with BUS_DMA_ZERO flag, so
allocated memory is already filled in by zeros
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Remove the first member alignment to cacheline since it is nop.
Use __aligned() for the whole structure to make sure that the structure
size is cacheline aligned.
Remove lock alignment to make the structure smaller and fit all members
used on event queue processing into one cacheline (128 bytes) on x86-64.
The lock is obtained as well from different context when event queue
statistics are retrived from sysctl context, but it is infrequent.
Reorder members to avoid padding and go in usage order on event
processing.
As the result all structure members used on event queue processing fit
into exactly one cacheline (128 byte) now.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
In fact the pointer is used only if more than one TXQ is processed in
one interrupt.
It is used (read-write) on completion path only.
Also it makes the first part of the structure smaller and it fits now
into one 128byte cache line. So, TXQ structure becomes 128 bytes smaller.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
doesn't get truncated to 32 bits.
Without this, 3x3 NICs transmitting at an MCS rate whose rix (rate
index) in the rate table is > 31 end up returning errors, as the
sample rate code doesn't think the rate is set in the rate table.
Tested:
* AR9380, STA, speaking 3x3 to an AP
Without this change a local attacker could trigger a panic by
tricking the kernel into accessing undefined kernel memory.
We would like to acknowledge Francisco Falcon from CORE Security
Technologies who discovered the issue and reported to the
FreeBSD Security Team.
More information can be found at CORE Security's advisory at:
http://www.coresecurity.com/content/freebsd-kernel-multiple-vulnerabilities
This is an errata candidate for releng/10.1 and releng/9.3. Earlier
releases are not affected.
Reported by: Francisco Falcon from CORE Security Technologies
Security: CVE-2014-0998
Reviewed by: dumbbell
MFC after: 3 days
Also, split power_suspend into power_suspend and power_suspend_early.
power_suspend_early is called before the userland is frozen.
power_suspend is called after the userland is frozen.
Currently only VT switching is hooked to power_suspend_early.
This is needed because switching away from X server requires its
cooperation, so obviously X server must not be frozen when that happens.
Freezing userland during ACPI suspend is useful because not all drivers
correctly handle suspension concurrent with other activity. This is
especially applicable to drivers ported from other operating systems
that suspend all software activity between placing drivers and hardware
into suspended state.
In particular drm2/radeon (radeonkms) depends on the described
procedure. The driver does not have any internal synchronization
between suspension activities and processing of userland requests.
Many thanks to kib for the code that allows to freeze and thaw all
userland threads.
Note that ideally we also need to park / inhibit (non-special) kernel
threads as well to ensure that they do not call into drivers.
MFC after: 17 days
suspend/resume
The goal is to avoid that the vt(4) resume happens before the video
display is resumed. The original patch was provided by Andriy Gapon.
This new patch registers the handlers in vt_upgrade(). This is done
once, thanks to the VDF_ASYNC flag. I abused this flag because it was
already abused by the keyboard allocation. The event handlers then call
the backend if it provides callbacks for suspend/resume.
Differential Revision: https://reviews.freebsd.org/D1004
On behalf of: dumbbell
MFC after: 2 weeks
Previously, the driver resets the device and abandon the requests that
are caught in flight when the dump was initiated. This was problematic
if the system is resumed after the dump is completed.
While that is probably not the typical action, it is simple to rework
the driver to very likely have the device usable after the dump without
making it more likely for the dump to fail. The in flight requests are
simply queued for completion once the dump is finished.
Requested by: markj
MFC after: 1 month
the no-longer existant sb_cc sockbuf member.
- Use sbavail() instead of sbused() in t4_soreceive_ddp() to match the
usage in soreceive_stream() on which it is based.
Discussed with: glebius (2)
for i386, and from the code inspection, nothing in the
arm/mips/sparc64 implementations depends on it.
Discussed with: imp, nwhitehorn
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
The newer boards don't have the response field that indicates
whether the SCSI status byte is present. You have to just look to
see whether it is non-zero.
The code was looking to see whether the sense length was valid
before propagating the SCSI status byte (and sense information) up
the stack. With a status like Reservation Conflict, there is no
sense information, only the SCSI status byte. So it wasn't getting
correctly returned.
isp.c:
In isp_intr(), if we are on a 2400 or 2500 type board and
get a response, look at the actual contents of the
SCSI status value and set the RQSF_GOT_STATUS flag
accordingly so that return any SCSI status value we get. The
RQSF_GOT_SENSE flag will get set later on if there is
actual sense information returned.
Submitted by: ken
MFC after: 1 week
Sponsored by: Spectra Logic
MFSpectraBSD: 1112791 on 2015/01/15
If the user sends an XPT_RESET_DEV CCB, make sure to reset the
Fibre Channel Command Reference Number if we're running on a FC
controller.
We send a SCSI Target Reset when we get this CCB, and as a result
need to reset the CRN to 1 on the next command.
isp_freebsd.c:
In the XPT_RESET_DEV implementation in isp_action(), reset
the CRN if we're on a FC controller.
Submitted by: ken
MFC after: 1 week
Sponsored by: Spectra Logic
MFSpectraBSD: 1112787 on 2015/01/15
Fix SCSI status byte reporting on 4Gb and 8Gb Qlogic boards.
The newer boards don't have the response field that indicates
whether the SCSI status byte is present. You have to just look to
see whether it is non-zero.
The code was looking to see whether the sense length was valid
before propagating the SCSI status byte (and sense information) up
the stack. With a status like Reservation Conflict, there is no
sense information, only the SCSI status byte. So it wasn't getting
correctly returned.
isp.c:
In isp_intr(), if we are on a 2400 or 2500 type board and
get a response, look at the actual contents of the
SCSI status value and set the RQSF_GOT_STATUS flag
accordingly so that return any SCSI status value we get. The
RQSF_GOT_SENSE flag will get set later on if there is
actual sense information returned.
Submitted by: ken
MFC after: 1 week
Sponsored by: Spectra Logic
MFSpectraBSD: 1112791 on 2015/01/15
systems with more than 4GB of physical memory.
To remotely debug the system 'stealthy' which has a kernel
with this change installed and firewire properly configured:
% fwcontrol -m stealthy (or stealthy's firewire EUI64)
% kgdb kernel /dev/fwmem0.0
sys/dev/firewire/fwohci.c:
Rather than hard code the upper limit for hw based
automatic responses to remote DMA requests at 4GB,
program the hardware using Maxmem, the page number
one higher than the highest physical page detected
in the system.
While here, garbage collect more useless splfw()
calls.
Submitted by: gibbs
MFC after: 1 week
Sponsored by: Spectra Logic
MFSpectraBSD: 1110994 on 2015/01/06
asynchronous remote dma request (DMA request that the
hardware cannot automatically handle).
sys/dev/firewire/firewire.c
In fw_rcv(), add missing early return in the error
path for DMA requests to unregistered regions.
Submitted by: gibbs
MFC after: 1 week
Sponsored by: Spectra Logic
MFSpectraBSD: 1110993 on 2015/01/06
sys/boot/i386/libfirewire/firewire.c:
sys/dev/firewire/firewire.c:
Fix configuration ROM generation count wrapping logic
so that the generation count is never outside of
allowed limits (0x2 -> 0xF).
sys/dev/firewire/firewire.c:
In fw_xfer_unload(), xfer->fc may be NULL. Protect
against this before taking the fc lock.
Submitted by: gibbs
MFC after: 1 week
Sponsored by: Spectra Logic
MFSpectraBSD: 1110685 on 2015/01/05
sys/dev/firewire/firewire.c:
In fw_xfer_unload() expand lock coverage so that
the test for FWXF_INQ doesn't race with it being
cleared in another thread.
Submitted by: gibbs
MFC after: 1 week
Sponsored by: Spectra Logic
MFSpectraBSD: 1110207 on 2015/01/02
sys/dev/firewire/firewire.c:
In fw_xfer_unload(), clear the FWXF_INQ flag on the
xfer under protection of the FW_GMTX, after the
xfer is removeed from the tx/rx queue. Otherwise
it is possible for the xfer to be removed again
(corrupting the list or immediately panicing) from
another thread that has found this xfer in the
transaction label table.
Submitted by: gibbs
MFC after: 1 week
Sponsored by: Spectra Logic
MFSpectraBSD: 1110200 on 2015/01/02
as the cpu id on arm64 as it may use two cells. In it's place we can use
the device id.
It is expected we will use the reg data on arm64 to enable cores so we
still need to read and store it even if it is not yet used.
Differential Revision: https://reviews.freebsd.org/D1555
Reviewed by: nwhitehorn
Sponsored by: The FreeBSD Foundation
commit 4d93914ae3db4a897ead4b. Some related drm infrastructure
changes are imported as needed.
Biggest update is the rewrite of the i915 gem io to more closely
follow Linux model, althought the mechanism used by FreeBSD port is
different.
Sponsored by: The FreeBSD Foundation
MFC after: 2 month
every operation to retrieve the bs_cookie value almost nothing actually uses.
The bus_space struct contains a private data pointer (poorly named bs_cookie,
now renamed to bs_privdata) which is used only by a few old armv4 xscale
implementations. The bus_space functions were all defined to take this
value as the first parameter instead of the bus_space_tag_t, requiring all
the inline macro and function expansions to dereference the tag to pass it
to another function, which never uses it. Now all the functions take the tag
as the first parameter and retrieve the privdata if they need it.
Also fix a couple bus_space_unmap() implementations that were calling
kva_free() instead of pmap_unmapdev().
Discussed with: cognet
This makes Mac OS X happy when it returns back from suspending.
o Switch notify state after data is transferred, but not before.
o Consider there is also Super Speed mode.
o Do not set stall bit on any pipes in device mode as Mac OS X seems
don't support it.
In collaboration with: hselasky@
driver on Rockchip boards. It currently supports PIO mode
and dma mode needs external dma controller to be used.
Submitted by: jmcneill
Approved by: stas (mentor)
"MODULE_VERSION" macro definition. Remove the redefinition of the
"MODULE_VERSION" macro from the Linux kernel compatibility API.
MFC after: 1 month
Reported by: np@
Sponsored by: Mellanox Technologies
bits.
The motivation here is to eventually teach netisr and potentially
other networking subsystems a bit more about how RSS work queues / buckets
are configured so things have a hope of auto-configuring in the future.
* net/rss_config.[ch] takes care of the generic bits for doing
configuration, hash function selection, etc;
* topelitz.[ch] is now in net/ rather than netinet/;
* (and would be in libkern if it didn't directly include RSS_KEYSIZE;
that's a later thing to fix up.)
* netinet/in_rss.[ch] now just contains the IPv4 specific methods;
* and netinet/in6_rss.[ch] now just contains the IPv6 specific methods.
This should have no functional impact on anyone currently using
the RSS support.
Differential Revision: D1383
Reviewed by: gnn, jfv (intel driver bits)
accidentally enable non-existent states.
This bug was triggered if ACPI advertises the presence of a C2 state
which we fail to parse via acpi_PkgGas due to our lack of support for
FFixedHW resources, and causes an immediate panic when an attempt is
made to enter the (NULL) state.
One affected platform is the EC2 c4.8xlarge VM instance type; there
may be others.
MFC after: 1 week
Thanks to: jkim, @_msw_
sdhci controllers, such as the one on a Raspberry Pi, mishandle the signal
timing in high speed signaling mode, but run just fine in standard mode
with the bus running at frequencies between 25-50MHz (which shouldn't work).
This is the solution adopted by U-Boot and other OSes (linux and *BSD)
for the timeouts on Raspberry Pi boards with certain SD cards. Some
research shows that this quirk is also used on a few other boards, so the
fix is a generic quirk instead of being in the RPi-specific driver code.
This change is based on information discovered by Michal Meloun.
Required when communicating to Mac OS X USB host stack.
o Also don't set stall bit to TX pipe in device mode as seems Mac OS X
don't clears it as it should.
Discussed with: hselasky@
in prep for the next NF calibration pass.
Totally missing braces. Damn you C.
Submitted by: Sascha Wildner <swildner@dragonflybsd.org>
MFC after: 1 week
MCI bluetooth coexistence method for WB222.
The rest of MCI requires a bunch more work, including adding a DMA buffer
for the MCI hardware to bounce messages in/out of and handling MCI
interrupts. But the more important part here is telling the HAL
the btcoex is enabled and MCI is in use so it configures the correct
initial bluetooth parameters in the wireless NIC and configures
things like bluetooth traffic weights and such.
So, this at least gets the HAL to do some of the right things in
configuring the inital bluetooth coexistence stuff, but doesn't
actually do full btcoex. That'll take.. some effort.
Tested:
* AR9462 (WB222), STA mode
tree's /chosen node to provide out-of-band header fields of the FDT. This
emulation is not perfect without corresponding changes to ofw_fdt_nextprop(),
but is enough to enable lookup by memory-map-parsing code.
MFC after: 1 week
resume sometimes (but not others). On powerup, other wierd issues show
up (sometimes the card comes up, but with really bogus pci config
space stuff. There may be more, but given my experience of historical
fussiness, stick to what works and make more minimal changes to that.
go back through HASWELL, IVY_BRIDGE, IVY_BRIDGE_XEON and SANDY_BRIDGE
to straighten out all the missing PMCs. We also add a new pmc tool
pmcstudy, this allows one to run the various formulas from
the documents "Using Intel Vtune Amplifier XE on XXX Generation platforms" for
IB/SB and Haswell. The tool also allows one to postulate your own
formulas with any of the various PMC's. At some point I will enahance
this to work with Brendan Gregg's flame-graphs so we can flamegraph
various PMC interactions. Note the manual page also needs some
work (lots of work) but gnn has committed to help me with that ;-)
Reviewed by: gnn
MFC after:1 month
Sponsored by: Netflix Inc.
can suspend / resume and unload / load cbb and cardbus without errors
on my Lenovo T400, which wasn't possible before. Cards suspending
and resuming in the CardBus slot not yet tested.
o Enable memory cycles to the bridge early (as part of the new
cbb_pci_bridge_init). This fixes the Bad VCC errors which were
caused by the code accessing the device registers with this
cleared. The suspend / resume process clears it.
o Refactor suspend / resume into bus specific code (though the ISA
code is just stubbed). This isn't strictly necessary, but makes
the initializaiton code more uniform and should be more bullet
proof in the face of variant behavior among cardbus bridges.
o Fixup comments in the power-up sequence to reflect reality. These
comments were written for one regime of power-up, but not updated
as things were revised.
o Add a paranoid small delay (100ms) to cover noisy cards powering
down.
o Fix some debugging prints to be easier to grep from dmesg.
Sponsored by: Netflix
simultaneously detaching kernel drivers on the same USB device we can
get stuck in the "usb_wait_pending_ref_locked()" function because the
conditions needed for allowing detach are not met. The "destroy_dev()"
function waits for all system calls involving the given character
device to return. Character device system calls may lock the USB
enumeration lock, which is also held when "destroy_dev()" is
called. This can sometimes lead to a deadlock not noticed by
WITNESS. The current solution is to ensure the calling thread is the
only one holding the USB enumeration lock and prevent other threads
from getting refs while a USB device detach is ongoing. This turned
out not to be sufficient. To solve this deadlock we could use
"destroy_dev_sched()" to schedule the device destruction in the
background, but then we don't know when it is safe to free() the
private data of the character device. Instead a callback function is
executed by the USB explore process to kill off any leftover USB
character devices synchronously after the USB device explore code is
finished and the USB enumeration lock is no longer locked. This makes
porting easier and also ensures us that character devices must
eventually go away after a USB device detach.
While at it ensure that "flag_iserror" is only written when "priv_mtx"
is locked, which is protecting it.
MFC after: 5 days
Before this change, the current code handles SIOCGIFADDR the same
way with SIOCSIFADDR, which involves full arp_ifinit, et al. They
should be unnecessary for SIOCGIFADDR case.
Differential Revision: https://reviews.freebsd.org/D1508
Reviewed by: glebius
MFC after: 2 weeks
Instead of reusing the same reg parsing code, create one, common function
that puts reg contents to the resource list. Address cells and size cells
are passed rather than acquired here so that any bus can have different
default values.
Obtained from: Semihalf
Reviewed by: andrew, ian, nwhitehorn
Sponsored by: The FreeBSD Foundation
driver name and NIC driver softc via the device(9) tree,
instead of going dirty through the ifnet(9) layer.
Differential Revision: D1506
Reviewed by: imp, jhb
if_ixl to version 1.3.0, if_ixlv to version 1.2.0
- Major change in both drivers is to add RSS support
- In ixl fix some interface speed related issues, dual
speed was not changing correctly, KR/X media was not
displaying correctly (this has a workaround until a
more robust media handling is in place)
- Add a warning when using Dell NPAR and the speed is
less than 10G
- Wrap a queue hung message in IXL_DEBUG, as it is non-fatal,
and without tuning can display excessively
MFC after: 1 week
unnecessary filter configuration code in nge_init_locked().
While I'm here add a check for driver running state for multicast
filter handling. Also remove unnecessary assignment to error
variable since it is cleared in the function entry.
Suggested by: brad@OpenBSD.org
devices which don't support the synchronize cache SCSI command are
likely to also not support the prevent-allow medium removal SCSI
command.
PR: 185747
MFC after: 1 week
moving the handling of curcmd->error != 0 to the end of the interrupt
handler. Also make sdhci_finish_data() idempotent by moving the setting
of slot->data_done = 1 down past the point where the busdma buffer is
unmapped. This allows for the possibility that the finish routine can
get called from multiple places when handling errors.
Poll for link state when the link is down, even for interrupt capable
PHYs.
Allow PHYs to report a dubious "partial" link. If this state is seen 3
consecutive times (each check is ~1s apart) then reset the PHY. This is
a workaround for a situation where repeatedly toggling the link from the
peer gets the AEL2005 PHY into a state where it never establishes a PCS
block lock even when everything is in order.
MFC after: 1 week
and not automatically come back if they were gone for a short
period of time.
The isp(4) driver has a 30 second gone device timer that gets
activated whenever a device goes away. If the device comes back
before the timer expires, we don't send a notification to CAM that
it has gone away. If, however, there is a command sent to the
device while it is gone and before it comes back, the isp(4) driver
sends the command back with CAM_SEL_TIMEOUT status.
CAM responds to the CAM_SEL_TIMEOUT status by removing the device.
In the case where a device comes back within the 30 second gone
device timer window, though, we weren't telling CAM the device
came back.
So, fix this by tracking whether we have told CAM the device is
gone, and if we have, send a rescan if it comes back within the 30
second window.
ispvar.h:
In the fcportdb_t structure, add a new bitfield,
reported_gone. This gets set whenever we return a command
with CAM_SEL_TIMEOUT status on a Fibre Channel device.
isp_freebsd.c:
In isp_done(), if we're sending CAM_SEL_TIMEOUT for for a
command sent to a FC device, set the reported_gone bit.
In isp_async(), in the ISPASYNC_DEV_STAYED case, rescan the
device in question if it is mapped to a target ID and has
been reported gone.
In isp_make_here(), take a port database entry argument,
and clear the reported_gone bit when we send a rescan to
CAM.
In isp_make_gone(), take a port database entry as an
argument, and set the reported_gone bit when we send an
async event telling CAM consumers that the device is gone.
Sponsored by: Spectra Logic
MFC after: 1 week
The Command Reference Number is used for precise delivery of
commands, and is part of the FC-Tape functionality set. (This is
only enabled for devices that support precise delivery of commands.)
It is an 8-bit unsigned number that increments from 1 to 255. The
commands sent by the initiator must be processed by the target in
CRN order if the CRN is non-zero.
There are certain scenarios where the Command Reference Number
sequence needs to be reset. When the target is power cycled, for
instance, the initiator needs to reset the CRN to 1. The initiator
will know this because it will see a LIP (when directly connected)
or get a logout/login event (when connected to a switch).
The isp(4) driver was not resetting the CRN when a target
went away and came back. When it saw the target again after a
power cycle, it would continue the CRN sequence where it left off.
The target would ignore the command because the CRN sequence is
supposed to be reset to 1 after a power cycle or other similar
event.
The symptom that the user would see is that there would be lots of
aborted INQUIRY commands after a tape library was power cycled, and
the library would fail to probe. The INQUIRY commands were being
ignored by the tape drive due to the CRN issue mentioned above.
isp_freebsd.c:
Add a new function, isp_fcp_reset_crn(). This will reset
all of the CRNs for a given port, or the CRNs for all LUNs
on a target.
Reset the CRNs for all targets on a port when we get a LIP,
loop reset, or loop down event.
Reset the CRN for a particular target when it arrives, is changed
or departs. This is less precise behavior than the
clearing behavior specified in the FCP-4 spec (which says
that it should be reset for PRLI, PRLO, PLOGI and LOGO),
but this is the level of information we have here. If this
is insufficient, then we will need to add more precise
notification from the lower level isp(4) code.
isp_freebsd.h:
Add a prototype for isp_fcp_reset_crn().
Sponsored by: Spectra Logic
MFC after: 1 week
socket-buffer implementations, introduce a return value for MCLGET()
(and m_cljget() that underlies it) to allow the caller to avoid testing
M_EXT itself. Update all callers to use the return value.
With this change, very few network device drivers remain aware of
M_EXT; the primary exceptions lie in mbuf-chain pretty printers for
debugging, and in a few cases, custom mbuf and cluster allocation
implementations.
NB: This is a difficult-to-test change as it touches many drivers for
which I don't have physical devices. Instead we've gone for intensive
review, but further post-commit review would definitely be appreciated
to spot errors where changes could not easily be made mechanically,
but were largely mechanical in nature.
Differential Revision: https://reviews.freebsd.org/D1440
Reviewed by: adrian, bz, gnn
Sponsored by: EMC / Isilon Storage Division
may also halt in C2 and not just C3 (it seems that in some cases the BIOS
advertises its C3 state as a C2 state in _CST). Just play it safe and
disable both C2 and C3 states if a user forces the use of the TSC as the
timecounter on such CPUs.
PR: 192316
Differential Revision: https://reviews.freebsd.org/D1441
No objection from: jkim
MFC after: 1 week
the knowledge of mbuf layout, and in particular constants such as M_EXT,
MLEN, MHLEN, and so on, in mbuf consumers by unifying various alignment
utility functions (M_ALIGN(), MH_ALIGN(), MEXT_ALIGN() in a single
M_ALIGN() macro, implemented by a now-inlined m_align() function:
- Move m_align() from uipc_mbuf.c to mbuf.h; mark as __inline.
- Reimplement M_ALIGN(), MH_ALIGN(), and MEXT_ALIGN() using m_align().
- Update consumers around the tree to simply use M_ALIGN().
This change eliminates a number of cases where mbuf consumers must be aware
of whether or not mbufs returned by the allocator use external storage, but
also assumptions about the size of the returned mbuf. This will make it
easier to introduce changes in how we use external storage, as well as
features such as variable-size mbufs.
Differential Revision: https://reviews.freebsd.org/D1436
Reviewed by: glebius, trasz, gnn, bz
Sponsored by: EMC / Isilon Storage Division
into mbuf storage, to reduce knowledge about mbuf/cluster layout in the
cxgb device driver.
Reviewed by: np
Sponsored by: EMC / Isilon Storage Division
which prevents us from doing a "callout_drain()" call. The callout in
question has a lock associated with it and we are not freeing the
callout. That means we can use the "callout_stop()" function to
atomically stop the callback iff the "callout_stop()" function is
called locked. This patch applies proper locking to "callout_stop()"
and replaces a "callout_drain()" with a "callout_stop()".
MFC after: 1 week
roughly 10 years, and the driver has not enjoyed any significant maintenance
since long before that. Despite well-meaning efforts from a number of
people, myself included, it never made the jump to 64-bit and was relegated
to the back-corners of i386. Now its frailty is hampering forward progress
with Clang. Any renewed engineering efforts are of course welcome and can
happen outside of the tree. No MFC of this is planned.
but not always, identical. In particular, the path entry may contain a
unit address that the name does not. If the FDT node does have an explicit
name property, treat that as an override of the FDT path rather than
ignoring it.
MFC after: 2 weeks
a) Front load as much work as possible in if_transmit, before any driver
lock or software queue has to get involved.
b) Replace buf_ring with a brand new mp_ring (multiproducer ring). This
is specifically for the tx multiqueue model where one of the if_transmit
producer threads becomes the consumer and other producers carry on as
usual. mp_ring is implemented as standalone code and it should be
possible to use it in any driver with tx multiqueue. It also has:
- the ability to enqueue/dequeue multiple items. This might become
significant if packet batching is ever implemented.
- an abdication mechanism to allow a thread to give up writing tx
descriptors and have another if_transmit thread take over. A thread
that's writing tx descriptors can end up doing so for an unbounded
time period if a) there are other if_transmit threads continuously
feeding the sofware queue, and b) the chip keeps up with whatever the
thread is throwing at it.
- accurate statistics about interesting events even when the stats come
at the expense of additional branches/conditional code.
The NIC txq lock is uncontested on the fast path at this point. I've
left it there for synchronization with the control events (interface
up/down, modload/unload).
c) Add support for "type 1" coalescing work request in the normal NIC tx
path. This work request is optimized for frames with a single item in
the DMA gather list. These are very common when forwarding packets.
Note that netmap tx in cxgbe already uses these "type 1" work requests.
d) Do not request automatic cidx updates every 32 descriptors. Instead,
request updates via bits in individual work requests (still every 32
descriptors approximately). Also, request an automatic final update
when the queue idles after activity. This means NIC tx reclaim is still
performed lazily but it will catch up quickly as soon as the queue
idles. This seems to be the best middle ground and I'll probably do
something similar for netmap tx as well.
e) Implement a faster tx path for WRQs (used by TOE tx and control
queues, _not_ by the normal NIC tx). Allow work requests to be written
directly to the hardware descriptor ring if room is available. I will
convert t4_tom and iw_cxgbe modules to this faster style gradually.
MFC after: 2 months
to change to 0xe822, which may be persistent across reboots and, thus,
confuse other OSes. Therefore, restore the original mode and frequency
setting on detach and shutdown.
- Report Ricoh R5CE822 as such.
- According to Linux, Ricoh R5CE822 also need SDHCI_QUIRK_LOWER_FREQUENCY.
- Nuke an unused softc member.
MFC after: 3 days
scatter-gather XHCI TRB entries for its payload data. The XHCI
controller can handle at least 65536 bytes per scatter-gather list
entry.
MFC after: 1 week
Suggested by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
Revert the EFI part of r276064 until I can test it properly on a real EFI
system. This was causing problems to people booting using UEFI and vt.
Reported by: O. Hartmann <ohartman@zedat.fu-berlin.de>
is called from "xhci_configure_reset_endpoint()". Ensure the 3-strikes
error feature is always enabled except for ISOCHRONOUS transfers.
MFC after: 1 week
Suggested by: marius@
chips with the same device and vendor IDs actually may provide different
functionality. While at it, canonicalize the description to match other
MosChip UARTs.
PR: 186891
MFC after: 3 days
- Simplify MSI allocation to what is actually needed for a single one.
- Release the MSI and the corresponding bus resource as appropriate when
either the interrupt resource cannot be allocated or setting up the
interrupt fails.
- Error out when interrupt allocation or setup fails and polling is
disabled.
- Release the MSI after the corresponding bus resource so the former is
not leaked on detach.
- Remove a redundant softc member.
MFC after: 3 days
for the lookup.
- For devices affected by PCI_QUIRK_MSI_INTX_BUG, ensure PCIM_CMD_INTxDIS
is cleared when using MSI/MSI-X.
- Employ PCI_QUIRK_MSI_INTX_BUG for BCM5714(S)/BCM5715(S)/BCM5780(S) rather
than clearing PCIM_CMD_INTxDIS unconditionally for all devices in bge(4).
MFC after: 3 days
AR5416 and later NICs have more than 8 (Well, more than 6) GPIO pins.
So to support rfkill on these NICs we need to bump this up or the
rfkill GPIO pin may get reset to the wrong value.
Noticed by: Anthony Jenkins <scoobi_doo@yahoo.com>
deselect it after setting the block size. This is a similar bug that
was fixed elsewhere, but not here. This makes sure that we leave the
card deselected at the end of the loop, and we don't send any commands
to the card without it selected.
Reviewed by: ian@
Current VT drivers don't register the memory regions they use with the
nexus. This patch makes vt_vga and vt_efifb register the memory regions they
use.
This is needed (at least) for Xen support, since the FreeBSD kernel will try
to use the holes in the memory map to map memory from other domains and
setup it's grant table.
Sponsored by: Citrix Systems R&D
Reported by: sbruno
Tested by: emaste
Reviewed by: ray
PR: 195537
Differential Revision: https://reviews.freebsd.org/D1291
Previously ahci_attach returned a hard coded ENXIO instead of the value
from ahci_setup_interrupt. This is effectively a NOOP change as currently
ahci_setup_interrupt only ever returns 0 or ENXIO, so just there to protect
against any future changes to that.
Differential Revision: D838
MFC after: 2 weeks
Sponsored by: Multiplay
This prevents the possiblity of any overruns on the statically allocated
struct irqs field.
Differential Revision: D838
MFC after: 2 weeks
X-MFC-With: r276012
Sponsored by: Multiplay
such as timeouts while probing a bus or testing for a feature, is
squelched. Also, error reporting is limited to 5 events per second,
because when an sdcard goes bad on a low-end embedded board, flooding
the console at high speed isn't helpful.
Original logging code contributed by Michal Meloun, but then I fancied
it up with squelching and ppsratecheck.
TI OMAP controllers which will return the reset-in-progress bit as zero if
you read the status register too fast after setting the reset bit.
The zero is apparently from a stale snapshot of the internal state presented
in the interface register, and leads to a false indication that the reset
is complete when it either hasn't started yet or is in-progress. The
workaround is to first loop until the bit is seen as asserted, then do the
normal loop waiting to see it de-asserted.
Submitted by: Michal Meloun <meloun@miracle.cz>
function parameters, the card has to be in transfer state. If it is in
the idle state, the commands are ignored. This caused us not to set
the proper parameters that we later assume to be present, leading to
downstream failures of the card / interface as our state machine
mismatches the card's.
Submitted by: Svatopluk Kraus <onwahe at gmail.com>, Michal Meloun
<meloun at miracle.cz>
While we don't support MCS, hole in received sequence numbers may mean
only PDU loss. While we don't support lost PDU recovery, terminate the
connection to avoid stuck commands.
While there, improve handling of sequence numbers wrap after 2^32 PDUs.
MFC after: 2 weeks
sheet, RX filter should be disabled before programming.
Previously it was clearing wrong bits so RX filter was not
disabled in RX filter configuration.
Reported by: brad@OpenBSD.org
This allows the Grant-table code to attach directly to the xenpv bus,
allowing us to remove the grant-table initialization done in xenpv.
Sponsored by: Citrix Systems R&D
Mave the grant table code into the dev/xen folder in preparation for turning
it into a device using the newbus interface. This is just code motion, no
functional changes.
Sponsored by: Citrix Systems R&D
When running as a Xen PVH Dom0 we need to add custom buses that override
some of the functionality present in the ACPI PCI Bus and the PCI Bus. We
currently override the ACPI PCI Bus, but not the PCI Bus, so add a new
override for the PCI Bus and share the generic functions between them.
Reported by: David P. Discher <dpd@dpdtech.com>
Sponsored by: Citrix Systems R&D
conf/files.amd64:
- Add the new files.
x86/xen/xen_pci_bus.c:
- Generic file that contains the PCI overrides so they can be used by the
several PCI specific buses.
xen/xen_pci.h:
- Prototypes for the generic overried functions.
dev/xen/pci/xen_pci.c:
- Xen specific override for the PCI bus.
dev/xen/pci/xen_acpi_pci.c:
- Xen specific override for the ACPI PCI bus.
o Move similar block/networking methods to common file
o Follow r275640 and correct MMIO registers width
o Pass value to MMIO platform_note method.
Sponsored by: DARPA, AFRL
There are two main parts to get it to work, 1) most of the register
accesses need to be word sized, other than the config register which
needs to be byte aligned, and 2) we don't need the platform driver
for this to work on the Foundation Model, allow it to be NULL.
Differential Revision: https://reviews.freebsd.org/D1240
Reviewed by: bryanv
Sponsored by: The FreeBSD Foundation
adapters. Set the pack boundary for T5 cards to be the same as the
PCIe max payload size. The chip likes it this way.
In this revision the driver allocate rx buffers that align on both
boundaries. This is not a strict requirement and a followup commit
will switch the driver to a more relaxed allocation strategy.
MFC after: 2 weeks
re-using a hardware propritary transfer descriptor, PTD, in USB host
mode. If the PTD's are recycled too quickly, it has been observed that
the hardware simply fails to schedule the requested job or resets
completely disconnecting all devices.
Always include the card human readable name. We support ~270 cards and
at ~20 bytes each, this bloats things by only ~5k. Retain the
PCMCIA_CARD vs PCMCIA_CARD_D distinction, though, in case this is
intolerable.
from the FreeBSD network code. The flag is still kept around in the
"sys/mbuf.h" header file, but does no longer have any users. Instead
the "m_pkthdr.rsstype" field in the mbuf structure is now used to
decide the meaning of the "m_pkthdr.flowid" field. To modify the
"m_pkthdr.rsstype" field please use the existing "M_HASHTYPE_XXX"
macros as defined in the "sys/mbuf.h" header file.
This patch introduces new behaviour in the transmit direction.
Previously network drivers checked if "M_FLOWID" was set in "m_flags"
before using the "m_pkthdr.flowid" field. This check has now now been
replaced by checking if "M_HASHTYPE_GET(m)" is different from
"M_HASHTYPE_NONE". In the future more hashtypes will be added, for
example hashtypes for hardware dedicated flows.
"M_HASHTYPE_OPAQUE" indicates that the "m_pkthdr.flowid" value is
valid and has no particular type. This change removes the need for an
"if" statement in TCP transmit code checking for the presence of a
valid flowid value. The "if" statement mentioned above is now a direct
variable assignment which is then later checked by the respective
network drivers like before.
Additional notes:
- The SCTP code changes will be committed as a separate patch.
- Removal of the "M_FLOWID" flag will also be done separately.
- The FreeBSD version has been bumped.
MFC after: 1 month
Sponsored by: Mellanox Technologies
- Add support for GEOM direct completion. Depending on the benchmark,
this tends to give a ~30% improvement w.r.t IOPs and BW.
- Remove an invariants check in the strategy routine. This assertion
is caught later on by an existing panic.
- Rename and resort various related functions to make more sense.
MFC after: 1 month
sending not ready data:
o Add new flag to pru_send() flags - PRUS_NOTREADY.
o Add new protocol method pru_ready().
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
o Introduce a notion of "not ready" mbufs in socket buffers. These
mbufs are now being populated by some I/O in background and are
referenced outside. This forces following implications:
- An mbuf which is "not ready" can't be taken out of the buffer.
- An mbuf that is behind a "not ready" in the queue neither.
- If sockbet buffer is flushed, then "not ready" mbufs shouln't be
freed.
o In struct sockbuf the sb_cc field is split into sb_ccc and sb_acc.
The sb_ccc stands for ""claimed character count", or "committed
character count". And the sb_acc is "available character count".
Consumers of socket buffer API shouldn't already access them directly,
but use sbused() and sbavail() respectively.
o Not ready mbufs are marked with M_NOTREADY, and ready but blocked ones
with M_BLOCKED.
o New field sb_fnrdy points to the first not ready mbuf, to avoid linear
search.
o New function sbready() is provided to activate certain amount of mbufs
in a socket buffer.
A special note on SCTP:
SCTP has its own sockbufs. Unfortunately, FreeBSD stack doesn't yet
allow protocol specific sockbufs. Thus, SCTP does some hacks to make
itself compatible with FreeBSD: it manages sockbufs on its own, but keeps
sb_cc updated to inform the stack of amount of data in them. The new
notion of "not ready" data isn't supported by SCTP. Instead, only a
mechanical substitute is done: s/sb_cc/sb_ccc/.
A proper solution would be to take away struct sockbuf from struct
socket and allow protocols to implement their own socket buffers, like
SCTP already does. This was discussed with rrs@.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Call to the driver-specific ioctl used to process ioctl number
that will lead to the out-of-bounds access to the ioctl handler
array.
PR: 193367
Approved by: kib
MFC after: 1 week
This allows one to make a kernel module to tune the
number of queues before the driver loads.
This is needed so that a module at SI_SUB_CPU can set
tunables for these drivers to take. Otherwise getenv
is called too early by the TUNABLE macros.
Reviewed by: smh
Phabric: https://reviews.freebsd.org/D1149
Records with target_mode == 1 are allocated from the end of portdb, so it
seems logical to start search from the end not traverse whole array.
MFC after: 1 month
