via AHCI-like memory resource at BAR(5). Use it if BIOS was so kind to
allocate memory for that BAR. This allows hot-plug support and connection
speed reporting.
MFC after: 2 weeks
i.e. alignment, max_address, max_iosize and segsize (only max_address is
thought to have an negative impact regarding this issue though), after
calling ata_dmainit() either directly or indirectly so these values have
no effect or at least no effect on the DMA tags and the defaults are used
for the latter instead. So change the drivers to set these parameters
up-front and ata_dmainit() to honor them.
Reviewd by: mav
MFC after: 1 month
- Implement proper combined mode decoding for Intel controllers to properly
identify SATA and PATA channels and associate ATA channels with SATA ports.
This fixes wrong reporting and in some cases hard resets to wrong SATA ports.
- Improve SATA registers support to handle hot-plug events and potentially
interface errors. For ICH5/6300ESB chipsets these registers accessible via
PCI config space. For later ones they may be accessible via PCI BAR(5).
- For controllers not generating interrupts on hot-plug events, implement
periodic status polling. Use it to detect hot-plug on Intel and VIA
controllers. Same probably could also be used for Serverworks and SIS.
K2 SATA controllers. The chip's status register must be read first, and
as a long, for other registers to be correctly updated after a command, and
this includes the command sequence in device detection as well as the
previously handled case after interrupts. While here, clean up some
previous hacks related to this controller.
Reported by: many
Reviewed by: mav
MFC after: 3 weeks
response to DMA activate FIS under certain circumstances. This is
recommended fix from chip datasheet. If triggered, this bug most likely
cause write command timeout.
MFC after: 2 weeks
value 0xff. On hot-plug this value confuses ata_generic_reset() device
presence detection logic. As soon as we already know drive presence from
SATA hard reset, hint ata_generic_reset() to wait for device signature
until success or full timeout.
corruption bug where if an ATA command is issued before DMA is started,
data will become available to the controller before it knows what to do
with it. This results in either data corruption or a controller crash.
This patch remedies the problem by adopting the workaround employed
by Linux and Darwin: starting the DMA engine prior to sending the ATA
command.
Observer on: Xserve G5
Reviewed by: mav
MFC after: 1 week
fix. On Apple OpenPICs, the low/high bit of the interrupt sense is only
respected for interrupt 0. We currently erroneously program all OpenPIC
interrupts level high instead of level low by default, which only matters
for some G5 systems where the SATA controllers use IRQ 0.
This change is a quick fix that will be reverted once the effect of
changing the default interrupt sense on embedded systems is known.
MFC after: 3 days
Limit early revisions from 6Gb/s to 3Gb/s by default, or they negotiate
only 1.5Gbps, when 3Gb/s devices connected.
Add dummy driver for PATA part of these controllers, preventing generic
driver attach them. It causes system freeze when SATA controller used after
PATA was touched.
- These revisions no longer have cable detection capability.
- The UDMA support bit of register 0x4b has been dropped without an
replacement.
- According to Linux it's crucial for working ATAPI DMA support to
also set the reserved bit 1 of regsiter 0x53 with these revisions.
MFC after: 1 week
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
