chipset-specific code to attach chipset-specific data.
- Use chipset-specific data in the acard and promise chipsets rather than
changing the ivars of ATA PCI devices. ivars are reserved for use by the
parent bus driver and are _not_ available for use by devices directly.
This fixes a panic during sysctl -a with certain Promise controllers with
ACPI enabled.
Reviewed by: mav
Tested by: Magnus Kling (kingfon @ gmail) (on 7)
MFC after: 3 days
- Generate fake channel interrupts even if channel busy with previous
request to let it finish. Without this, dumping requests were just queued
and never processed.
- Drop pre-dump requests queue on dumping. ATA code, working in dumping
(interruptless) mode, unable to handle long request queue. Actually, to get
coherent dump we anyway should do as few unrelated actions as possible.
Feature is controlled by hint.ata.X.pm_level tunable:
0 - PM disabled, old behaviour, default.
1 - device is allowed to initiate PM state change, host is passive.
2 - host initiates PARTIAL state transition every time port is idle.
3 - host initiates SLUMBER state transition every time port is idle.
PARTIAL state has up to 100us (50us for me) wakeup latency, but for my
ICH8M saves 0.5W of power per drive. SLUMBER state has up to 10ms (3.5ms
for me) wakeup latency, but saves 0.8W of power.
Modes 2 and 3 are implemented only for AHCI driver now.
Interface power management is incompatible with device presence detection
(host receives no signal from drive, so unable to monitor it), so later is
disabled when PM is used.
controllers may be configured as legacy IDE mode by modifying subclass and
progif without actually changing PCI device IDs. Instead of complicating
code, we always force AHCI mode while probing. Also we restore AHCI mode
while resuming per ATI/AMD register programming/requirement guides.
- Fix SB700/800 "combined" mode. Unlike SB600, this PATA controller can
combine two SATA ports and emulate one PATA channel as primary or secondary
depending on BIOS configuration. When the combined mode is disabled, this
channel disappears and it works just like SB600 PATA controller, however.
- Add more PCI device IDs for SB700/800 and adjust device descriptions.
SB800 shares the same PCI device IDs and added two more SATA IDs.
the ATA status register with a 4-byte read request. This updates it, and
subsequent 1-byte reads will return the correct result.
This commit adds a hack to do this, which is currently ifdef'd powerpc,
although Linux and Darwin do this unconditionally on all platforms.
Add ch_suspend/ch_resume methods for PCI controllers and implement them
for AHCI. Refactor AHCI channel initialization according to it.
Fix Port Multipliers operation. It is far from perfect yet, but works now.
Tested with JMicron JMB363 AHCI + SiI 3726 PMP pair.
Previous version was also tested with SiI 4726 PMP.
Hardware sponsored by: Vitsch Electronics / VEHosting.nl
both disks, or if we should suppress the slave drive. Default to
suppressing the slave, in the case that this REQIURED tuple turns out
to not actually be present...
ready status. Most of controllers managed to issue coommand and set BUSY
bit almost simultaneously, before we will read it, but at least JMicron JMB363
don't. Ignore timeout errors to keep old behavior when error there was
impossible.
For me this fixes timeout errors on the first command after channel attach
or reinit. Boot in my case is not affected, as there is much time passing
between reset and next command giving reset time to complete.
done in other places. Until we have no support for command queueing we have
no any benefit from FBS, while enabling it only here somehow leads to
"port not ready" errors on Intel 63XXESB2 controller.
Tested by: Larry Rosenman <ler AT lerctr.org>
and partially r188903. Revert breaks new drives detection on reinit to the
state as it was before me, but fixes series of new bugs reported by some
people.
Unconditional queueing of ata_completed() calls can lead to deadlock if
due to timeout ata_reinit() was called at the same thread by previous
ata_completed(). Calling of ata_identify() on ata_reinit() in current
implementation opens numerous races and deadlocks.
Problems I was touching here are still exist and should be addresed, but
probably in different way.
drivers' probe routines. It allows not to sleep and so not drop Giant inside
ata_identify() critical section and so avoid crash if it reentered on
request timeout. Reentering of probe call checked inside of it.
Give device own knowledge about it's type (ata/atapi/atapicam). It is not
a good idea to ask channel status for device type inside ata_getparam().
Add softc memory deallocation on device destruction.
kernel dumping case.
ata_completed() may initiate ata_reinit() on error, that may lead to drives
attach or detach. Attach and detach are sending requests to drives and sleep
waiting for results. But ata_finish() can be called directly from
interrupt handler where sleeping is prohibited, so we must break this chain
somewhere. This place seems to fit best.
- protect againtst recursions,
- add new devices detection using ata_identify().
Improve ata_identify():
- do not add duplicate device if device already exist.
Rework SATA hot-plug events handling. Instead of unsafe duplicate
implementation use common ata_reinit() to handle all state changes.
All together this gives quite stable and robust cold- and hot-plug operation,
invariant to false, lost and duplicate events.
ATA specification declares minimal reset time of 5us. SATA keeps it, but
requires devices to handle commands transmitted even one by one without
any gap.
as ATA RAID, but generic ATAPCI driver unable to detect drives there. AHCI
driver reported to handle them fine. Linux does the same.
Submitted by: Andrey V. Elsukov on stable@
ata_detach() to implement IOCATAATTACH/IOCATADETACH ioctls.
This will permit channel drivers to properly shutdown port hardware on channel
detach and init it on attach.
join allocate() and dmainit() atapci subdriver's channel initialization
methods into single ch_attach() method.
As opposite to ch_attach() add new ch_detach() method to deallocate/disable
channel.
to not allocate them after the recent ata channels enumeration changes.
It allows to save some resources, not bother user with unexisting hardware
and not check unimplemented ports status on every interrupt.
Works fine with AHCI and theoretically other MSI capable devices.
At this moment support disabled by default. To enable it, set
"hint.atapci.X.msi=1" device hint.
- specification claims that 1 second is just a maximum controller reset time;
implement controller reset properly to save almost 1 second of boot, and
about half second of resume time;
- enable channel interrupts only after channel status reset to fix duplicate
device creation on resume due to unwanted device connection event;
- as described in specification, wait for disk ready status after channel
power-up; it is not so important when disk already touched by BIOS, but
solves device not ready problems on resume and probably some other cases.
- uncomment channel stop/start on soft-reset as it is declared mandatory by
specification; it was commented due to some random drive detection problems
on VIA and JMicron controllers, but I hope it is fixed by previous point.
Move channel softc initialization from ata_XXX_probe() to ata_XXX_attach().
Instead of calculating ata channel number as position in child device list,
pass it's real number directly from controller probe routine using ivars.
It is simpler and IMHO more correct.
expected in acd_fixate().
This should fix various problems folks are having with 'burncd' reporting
"burncd: ioctl(CDRIOCFIXATE): Input/output error" during the fixate phase
when "fixate" is issued together with the "data" command.
PR: 95979
Submitted by: Jaakko Heinonen <jh@saunalahti.fi>
created by atapicam is being kept opened or mounted. This is probably just
a temporary solution until we invent something better.
Reviewed by: scottl
Approved by: rwatson (mentor)
Sponsored by: FreeBSD Foundation
Reported by: Jaakko Heinonen
storage class. This check was lost. It is not important for the most cases,
but as it was reported on current@, it does important for sis driver and
surely inportant for AHCI driver. So restore it there.
Submitted by: Toshikazu ICHINOSEKI, Andrey V. Elsukov
Discussed on: current@
configuration registers (which are not going to change) on every interrupt
looks expensive, especially when interrupt is shared. Profiling shows me 3%
of time spent by atapci0 on pure network load due to IRQ sharing with em0.
(still a power of 2) rather than 63k transfers. Even with 63k transfers
some machines (such as Dell SC1435's) were experiencing chronic data
corruption.
- Use the MIO method to talk to the Serverworks HT1000_S1 SATA controller
like all the other SATA controllers rather than the compat PATA
method. This lets the controller see all 4 SATA ports and also
matches the behavior of the Linux driver.
Silence from: sos
MFC after: 3 days
If you just config KERNEL as usual there should be no apparent changes, you'll get all chipset support code compiled in.
However there is now a way to only compile in code for chipsets needed on a pr vendor basis. ATA now has the following "device" entries:
atacore: ATA core functionality, always needed for any ATA setup
atacard: CARDBUS support
atacbus: PC98 cbus support
ataisa: ISA bus support
atapci: PCI bus support only generic chipset support.
ataahci: AHCI support, also pulled in by some vendor modules.
ataacard, ataacerlabs, ataadaptec, ataamd, ataati, atacenatek, atacypress, atacyrix, atahighpoint, ataintel, ataite, atajmicron, atamarvell, atamicron, atanational, atanetcell, atanvidia, atapromise, ataserverworks, atasiliconimage, atasis, atavia; Vendor support, ie atavia for VIA chipsets
atadisk: ATA disk driver
ataraid: ATA softraid driver
atapicd: ATAPI cd/dvd driver
atapifd: ATAPI floppy/flashdisk driver
atapist: ATAPI tape driver
atausb: ATA<>USB bridge
atapicam: ATA<>CAM bridge
This makes it possible to config a kernel with just VIA chipset support by having the following ATA lines in the kernel config file:
device atacore
device atapci
device atavia
And then you need the atadisk, atapicd etc lines in there just as usual.
If you use ATA as modules loaded at boot there is few changes except the rename of the "ata" module to "atacore", things looks just as usual.
However under atapci you now have a whole bunch of vendor specific drivers, that you can kldload individually depending on you needs. Drivers have the same names as used in the kernel config explained above.
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
Thanks goes to ITE who provided docs and feedback and made this possible.
Minor fixups to the Intel ICH code for bugs found while doing this.
(ITE8213 is very semilar to an Intel ICH)
MFC after: 1 week
This can be used to disable the 80pin cable check on systems which forget to
set the bit -- such as certain laptops and Soekris boards.
PR: kern/114605 (somewhat reworked)
Submitted by: marck
MFC after: 1 week
when it worked as generic IDE.
PR: 125422
Submitted by: Andrey V. Elsukov <bu7cher at yandex dot ru>
Approved by: imp (mentor, implicit)
MFC after: 1 week
Handle cases where dma function pointers may be NULL, and where
the max_iosize can't be derived from a DMA data structure. For
the latter, revert to the prior behaviour of using DFLTPHYS for
the max i/o size when there is no other data.
Reviewed by: marcel
No objection by: sos
So if we have channel 0..3 devclass_get_maxunit is 4.
It's never been a problem as devclass_get_device() has
catched a possibly bad input.
Discussed with: scottl
This avoids calling busdma in the request processing path which caused a traumatic performance degradation.
Allocation has be postponed to after we know how many devices we possible can have on portmulitpliers to save some space.
The problem is that the PM support is part of a much larger WIP here, but due to popular demand I decided to get some of it imported.
Also I forgot the mention:
HW sponsored by: Vitsch Electronics / VEHosting
Support is working on the Silicon Image SiI3124/3132.
Support is working on some AHCI chips but far from all.
Remember this is WIP, so test reports and (constructive) suggestions are welcome!
for a configurable number of seconds, spin the disk down. Spin it back
up on the next request.
Notice that the timeout is only armed by a request, so to spin down a
disk you may have to do:
atacontrol spindown ad10 5
dd if=/dev/ad10 of=/dev/null count=1
To disable spindown, set timeout to zero:
atacontrol spindown ad10 0
In order to debug any trouble caused, this code is somewhat noisy on the
console.
Enabling spindown on a disk containing / or /var/log/messages is not
going to do anything sensible.
Spinning a disk up and down all the time will wear it out, use sensibly.
Approved by: sos
set, announce BIO_DELETE capability and issue ATA_CFA_ERASE when we get one.
Once we issue more BIO_DELETE, this will improve lifetime, and
possibly write speed of Flash based devices which have usable flash
adaptation layers.
For now, about the only usage is the newfs(1) -E flag.
Approved by: sos
peoples code with irrelevant changes[1]:
Use bus_{read|write_*() instead of bus_space_{read|write}_*() for
purely stylistic reasons.
Due to compiler optimizations and inlining, this is for all practical
purposes without effect in the compiled code.
[1] NB: Approved by: sos
The HT1000 DMA engine seems to not always like 64K transfers and sometimes barfs data all over memory leading to instant chrash and burn.
Also fix 48bit adressing issues, apparently newer chips needs 16bit writes and not the usual fifo thing.
HW donated by: Travis Mikalson at TerraNovaNet
Revert the probe in atapi-cd.c to the old usage now its fixed on AHCI.
THis change also fixes using virtual CD's om fx parallels.
Still leaves the GEOM problem of telling media vs device access apart in the access function.
UDMA modes.
Please notice that Soekris NET5501 bios versions before 1.32f has a bug
that prevents this from working.
Approved by: re (gnn)
MFC: 2 weeks
detailed status on each of the backing subdisks. This allows userland
to see which subdisks are online, failed, missing, or a hot spare.
MFC after: 1 week
Approved by: re (bmah)
Reviewed by: sos
some false positives but at this moment it is better to add
support then to dont have it at all (comment from Soren).
PR: kern/111516
Submitted by: Thomas Nystrom <thn at saeab dot se>
Approved by: re (kensmith)
Approved by: imp (mentor)
OK'ed by: sos (With the comment noted above about false
positives).
now takes a device_t to be the parent of the bus that is being created.
Most SIMs have been updated with a reasonable argument, but a few exceptions
just pass NULL for now. This argument isn't used yet and the newbus
integration likely won't be ready until after 7.0-RELEASE.
than the 5288.
It is not correctly implemented in earlier silicon, and the BIOS often
lies about AHCI capability on platforms where these chips are deployed.
With this change I am able to boot FreeBSD on the ASUS Vintage AH-1
barebones system.
Approved by: sos
as some combinations of chipset, controller and target do not behave
correctly when DMA is enabled for other commands.
PR: kern/103602
MFC after: 2 weeks
This workaround the problem in Parallels/VMWare where the emulated drivers are
slower, especially with ATA_FLUSHCACHE. The problem appears much more
frequently with ZFS which use it a lot more.
Approved: sos, pjd
use to synchornize and protect all data objects that are used for that
SIM. Drivers that are not yet MPSAFE register Giant and operate as
usual. RIght now, no drivers are MPSAFE, though a few will be changed
in the coming week as this work settles down.
The driver API has changed, so all CAM drivers will need to be recompiled.
The userland API has not changed, so tools like camcontrol do not need to
be recompiled.
