freebsd-nq/sys/pci/if_rl.c

/*-
 * Copyright (c) 1997, 1998
 *	Bill Paul <wpaul@ctr.columbia.edu>.  All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. All advertising materials mentioning features or use of this software
 *    must display the following acknowledgement:
 *	This product includes software developed by Bill Paul.
 * 4. Neither the name of the author nor the names of any co-contributors
 *    may be used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED.  IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
 * THE POSSIBILITY OF SUCH DAMAGE.
 */

#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");

/*
 * RealTek 8129/8139 PCI NIC driver
 *
 * Supports several extremely cheap PCI 10/100 adapters based on
 * the RealTek chipset. Datasheets can be obtained from
 * www.realtek.com.tw.
 *
 * Written by Bill Paul <wpaul@ctr.columbia.edu>
 * Electrical Engineering Department
 * Columbia University, New York City
 */
/*
 * The RealTek 8139 PCI NIC redefines the meaning of 'low end.' This is
 * probably the worst PCI ethernet controller ever made, with the possible
 * exception of the FEAST chip made by SMC. The 8139 supports bus-master
 * DMA, but it has a terrible interface that nullifies any performance
 * gains that bus-master DMA usually offers.
 *
 * For transmission, the chip offers a series of four TX descriptor
 * registers. Each transmit frame must be in a contiguous buffer, aligned
 * on a longword (32-bit) boundary. This means we almost always have to
 * do mbuf copies in order to transmit a frame, except in the unlikely
 * case where a) the packet fits into a single mbuf, and b) the packet
 * is 32-bit aligned within the mbuf's data area. The presence of only
 * four descriptor registers means that we can never have more than four
 * packets queued for transmission at any one time.
 *
 * Reception is not much better. The driver has to allocate a single large
 * buffer area (up to 64K in size) into which the chip will DMA received
 * frames. Because we don't know where within this region received packets
 * will begin or end, we have no choice but to copy data from the buffer
 * area into mbufs in order to pass the packets up to the higher protocol
 * levels.
 *
 * It's impossible given this rotten design to really achieve decent
 * performance at 100Mbps, unless you happen to have a 400Mhz PII or
 * some equally overmuscled CPU to drive it.
 *
 * On the bright side, the 8139 does have a built-in PHY, although
 * rather than using an MDIO serial interface like most other NICs, the
 * PHY registers are directly accessible through the 8139's register
 * space. The 8139 supports autonegotiation, as well as a 64-bit multicast
 * filter.
 *
 * The 8129 chip is an older version of the 8139 that uses an external PHY
 * chip. The 8129 has a serial MDIO interface for accessing the MII where
 * the 8139 lets you directly access the on-board PHY registers. We need
 * to select which interface to use depending on the chip type.
 */

#ifdef HAVE_KERNEL_OPTION_HEADERS
#include "opt_device_polling.h"
#endif

#include <sys/param.h>
#include <sys/endian.h>
#include <sys/systm.h>
#include <sys/sockio.h>
#include <sys/mbuf.h>
#include <sys/malloc.h>
#include <sys/kernel.h>
#include <sys/module.h>
#include <sys/socket.h>

#include <net/if.h>
#include <net/if_arp.h>
#include <net/ethernet.h>
#include <net/if_dl.h>
#include <net/if_media.h>
#include <net/if_types.h>

#include <net/bpf.h>

#include <machine/bus.h>
#include <machine/resource.h>
#include <sys/bus.h>
#include <sys/rman.h>

#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>

#include <dev/pci/pcireg.h>
#include <dev/pci/pcivar.h>

MODULE_DEPEND(rl, pci, 1, 1, 1);
MODULE_DEPEND(rl, ether, 1, 1, 1);
MODULE_DEPEND(rl, miibus, 1, 1, 1);

/* "device miibus" required.  See GENERIC if you get errors here. */
#include "miibus_if.h"

/*
 * Default to using PIO access for this driver. On SMP systems,
 * there appear to be problems with memory mapped mode: it looks like
 * doing too many memory mapped access back to back in rapid succession
 * can hang the bus. I'm inclined to blame this on crummy design/construction
 * on the part of RealTek. Memory mapped mode does appear to work on
 * uniprocessor systems though.
 */
#define RL_USEIOSPACE

#include <pci/if_rlreg.h>

/*
 * Various supported device vendors/types and their names.
 */
static struct rl_type rl_devs[] = {
	{ RT_VENDORID, RT_DEVICEID_8129, RL_8129,
		"RealTek 8129 10/100BaseTX" },
	{ RT_VENDORID, RT_DEVICEID_8139, RL_8139,
		"RealTek 8139 10/100BaseTX" },
	{ RT_VENDORID, RT_DEVICEID_8139D, RL_8139,
		"RealTek 8139 10/100BaseTX" },
	{ RT_VENDORID, RT_DEVICEID_8138, RL_8139,
		"RealTek 8139 10/100BaseTX CardBus" },
	{ RT_VENDORID, RT_DEVICEID_8100, RL_8139,
		"RealTek 8100 10/100BaseTX" },
	{ ACCTON_VENDORID, ACCTON_DEVICEID_5030, RL_8139,
		"Accton MPX 5030/5038 10/100BaseTX" },
	{ DELTA_VENDORID, DELTA_DEVICEID_8139, RL_8139,
		"Delta Electronics 8139 10/100BaseTX" },
	{ ADDTRON_VENDORID, ADDTRON_DEVICEID_8139, RL_8139,
		"Addtron Technolgy 8139 10/100BaseTX" },
	{ DLINK_VENDORID, DLINK_DEVICEID_530TXPLUS, RL_8139,
		"D-Link DFE-530TX+ 10/100BaseTX" },
	{ DLINK_VENDORID, DLINK_DEVICEID_690TXD, RL_8139,
		"D-Link DFE-690TXD 10/100BaseTX" },
	{ NORTEL_VENDORID, ACCTON_DEVICEID_5030, RL_8139,
		"Nortel Networks 10/100BaseTX" },
	{ COREGA_VENDORID, COREGA_DEVICEID_FETHERCBTXD, RL_8139,
		"Corega FEther CB-TXD" },
	{ COREGA_VENDORID, COREGA_DEVICEID_FETHERIICBTXD, RL_8139,
		"Corega FEtherII CB-TXD" },
	{ PEPPERCON_VENDORID, PEPPERCON_DEVICEID_ROLF, RL_8139,
		"Peppercon AG ROL-F" },
	{ PLANEX_VENDORID, PLANEX_DEVICEID_FNW3603TX, RL_8139,
		"Planex FNW-3603-TX" },
	{ PLANEX_VENDORID, PLANEX_DEVICEID_FNW3800TX, RL_8139,
		"Planex FNW-3800-TX" },
	{ CP_VENDORID, RT_DEVICEID_8139, RL_8139,
		"Compaq HNE-300" },
	{ LEVEL1_VENDORID, LEVEL1_DEVICEID_FPC0106TX, RL_8139,
		"LevelOne FPC-0106TX" },
	{ EDIMAX_VENDORID, EDIMAX_DEVICEID_EP4103DL, RL_8139,
		"Edimax EP-4103DL CardBus" }
};

static int rl_attach(device_t);
static int rl_detach(device_t);
static void rl_dmamap_cb(void *, bus_dma_segment_t *, int, int);
static int rl_dma_alloc(struct rl_softc *);
static void rl_dma_free(struct rl_softc *);
static void rl_eeprom_putbyte(struct rl_softc *, int);
static void rl_eeprom_getword(struct rl_softc *, int, uint16_t *);
static int rl_encap(struct rl_softc *, struct mbuf **);
static int rl_list_tx_init(struct rl_softc *);
static int rl_list_rx_init(struct rl_softc *);
static int rl_ifmedia_upd(struct ifnet *);
static void rl_ifmedia_sts(struct ifnet *, struct ifmediareq *);
static int rl_ioctl(struct ifnet *, u_long, caddr_t);
static void rl_intr(void *);
static void rl_init(void *);
static void rl_init_locked(struct rl_softc *sc);
static void rl_mii_send(struct rl_softc *, uint32_t, int);
static void rl_mii_sync(struct rl_softc *);
static int rl_mii_readreg(struct rl_softc *, struct rl_mii_frame *);
static int rl_mii_writereg(struct rl_softc *, struct rl_mii_frame *);
static int rl_miibus_readreg(device_t, int, int);
static void rl_miibus_statchg(device_t);
static int rl_miibus_writereg(device_t, int, int, int);
#ifdef DEVICE_POLLING
static void rl_poll(struct ifnet *ifp, enum poll_cmd cmd, int count);
static void rl_poll_locked(struct ifnet *ifp, enum poll_cmd cmd, int count);
#endif
static int rl_probe(device_t);
static void rl_read_eeprom(struct rl_softc *, uint8_t *, int, int, int);
static void rl_reset(struct rl_softc *);
static int rl_resume(device_t);
static void rl_rxeof(struct rl_softc *);
static void rl_setmulti(struct rl_softc *);
static int rl_shutdown(device_t);
static void rl_start(struct ifnet *);
static void rl_start_locked(struct ifnet *);
static void rl_stop(struct rl_softc *);
static int rl_suspend(device_t);
static void rl_tick(void *);
static void rl_txeof(struct rl_softc *);
static void rl_watchdog(struct rl_softc *);

#ifdef RL_USEIOSPACE
#define RL_RES			SYS_RES_IOPORT
#define RL_RID			RL_PCI_LOIO
#else
#define RL_RES			SYS_RES_MEMORY
#define RL_RID			RL_PCI_LOMEM
#endif

static device_method_t rl_methods[] = {
	/* Device interface */
	DEVMETHOD(device_probe,		rl_probe),
	DEVMETHOD(device_attach,	rl_attach),
	DEVMETHOD(device_detach,	rl_detach),
	DEVMETHOD(device_suspend,	rl_suspend),
	DEVMETHOD(device_resume,	rl_resume),
	DEVMETHOD(device_shutdown,	rl_shutdown),

	/* bus interface */
	DEVMETHOD(bus_print_child,	bus_generic_print_child),
	DEVMETHOD(bus_driver_added,	bus_generic_driver_added),

	/* MII interface */
	DEVMETHOD(miibus_readreg,	rl_miibus_readreg),
	DEVMETHOD(miibus_writereg,	rl_miibus_writereg),
	DEVMETHOD(miibus_statchg,	rl_miibus_statchg),

	{ 0, 0 }
};

static driver_t rl_driver = {
	"rl",
	rl_methods,
	sizeof(struct rl_softc)
};

static devclass_t rl_devclass;

DRIVER_MODULE(rl, pci, rl_driver, rl_devclass, 0, 0);
DRIVER_MODULE(rl, cardbus, rl_driver, rl_devclass, 0, 0);
DRIVER_MODULE(miibus, rl, miibus_driver, miibus_devclass, 0, 0);

#define EE_SET(x)					\
	CSR_WRITE_1(sc, RL_EECMD,			\
		CSR_READ_1(sc, RL_EECMD) | x)

#define EE_CLR(x)					\
	CSR_WRITE_1(sc, RL_EECMD,			\
		CSR_READ_1(sc, RL_EECMD) & ~x)

/*
 * Send a read command and address to the EEPROM, check for ACK.
 */
static void
rl_eeprom_putbyte(struct rl_softc *sc, int addr)
{
	register int		d, i;

	d = addr | sc->rl_eecmd_read;

	/*
	 * Feed in each bit and strobe the clock.
	 */
	for (i = 0x400; i; i >>= 1) {
		if (d & i) {
			EE_SET(RL_EE_DATAIN);
		} else {
			EE_CLR(RL_EE_DATAIN);
		}
		DELAY(100);
		EE_SET(RL_EE_CLK);
		DELAY(150);
		EE_CLR(RL_EE_CLK);
		DELAY(100);
	}
}

/*
 * Read a word of data stored in the EEPROM at address 'addr.'
 */
static void
rl_eeprom_getword(struct rl_softc *sc, int addr, uint16_t *dest)
{
	register int		i;
	uint16_t		word = 0;

	/* Enter EEPROM access mode. */
	CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_PROGRAM|RL_EE_SEL);

	/*
	 * Send address of word we want to read.
	 */
	rl_eeprom_putbyte(sc, addr);

	CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_PROGRAM|RL_EE_SEL);

	/*
	 * Start reading bits from EEPROM.
	 */
	for (i = 0x8000; i; i >>= 1) {
		EE_SET(RL_EE_CLK);
		DELAY(100);
		if (CSR_READ_1(sc, RL_EECMD) & RL_EE_DATAOUT)
			word |= i;
		EE_CLR(RL_EE_CLK);
		DELAY(100);
	}

	/* Turn off EEPROM access mode. */
	CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_OFF);

	*dest = word;
}

/*
 * Read a sequence of words from the EEPROM.
 */
static void
rl_read_eeprom(struct rl_softc *sc, uint8_t *dest, int off, int cnt, int swap)
{
	int			i;
	uint16_t		word = 0, *ptr;

	for (i = 0; i < cnt; i++) {
		rl_eeprom_getword(sc, off + i, &word);
		ptr = (uint16_t *)(dest + (i * 2));
		if (swap)
			*ptr = ntohs(word);
		else
			*ptr = word;
	}
}

/*
 * MII access routines are provided for the 8129, which
 * doesn't have a built-in PHY. For the 8139, we fake things
 * up by diverting rl_phy_readreg()/rl_phy_writereg() to the
 * direct access PHY registers.
 */
#define MII_SET(x)					\
	CSR_WRITE_1(sc, RL_MII,				\
		CSR_READ_1(sc, RL_MII) | (x))

#define MII_CLR(x)					\
	CSR_WRITE_1(sc, RL_MII,				\
		CSR_READ_1(sc, RL_MII) & ~(x))

/*
 * Sync the PHYs by setting data bit and strobing the clock 32 times.
 */
static void
rl_mii_sync(struct rl_softc *sc)
{
	register int		i;

	MII_SET(RL_MII_DIR|RL_MII_DATAOUT);

	for (i = 0; i < 32; i++) {
		MII_SET(RL_MII_CLK);
		DELAY(1);
		MII_CLR(RL_MII_CLK);
		DELAY(1);
	}
}

/*
 * Clock a series of bits through the MII.
 */
static void
rl_mii_send(struct rl_softc *sc, uint32_t bits, int cnt)
{
	int			i;

	MII_CLR(RL_MII_CLK);

	for (i = (0x1 << (cnt - 1)); i; i >>= 1) {
		if (bits & i) {
			MII_SET(RL_MII_DATAOUT);
		} else {
			MII_CLR(RL_MII_DATAOUT);
		}
		DELAY(1);
		MII_CLR(RL_MII_CLK);
		DELAY(1);
		MII_SET(RL_MII_CLK);
	}
}

/*
 * Read an PHY register through the MII.
 */
static int
rl_mii_readreg(struct rl_softc *sc, struct rl_mii_frame *frame)
{
	int			i, ack;

	/* Set up frame for RX. */
	frame->mii_stdelim = RL_MII_STARTDELIM;
	frame->mii_opcode = RL_MII_READOP;
	frame->mii_turnaround = 0;
	frame->mii_data = 0;

	CSR_WRITE_2(sc, RL_MII, 0);

	/* Turn on data xmit. */
	MII_SET(RL_MII_DIR);

	rl_mii_sync(sc);

	/* Send command/address info. */
	rl_mii_send(sc, frame->mii_stdelim, 2);
	rl_mii_send(sc, frame->mii_opcode, 2);
	rl_mii_send(sc, frame->mii_phyaddr, 5);
	rl_mii_send(sc, frame->mii_regaddr, 5);

	/* Idle bit */
	MII_CLR((RL_MII_CLK|RL_MII_DATAOUT));
	DELAY(1);
	MII_SET(RL_MII_CLK);
	DELAY(1);

	/* Turn off xmit. */
	MII_CLR(RL_MII_DIR);

	/* Check for ack */
	MII_CLR(RL_MII_CLK);
	DELAY(1);
	ack = CSR_READ_2(sc, RL_MII) & RL_MII_DATAIN;
	MII_SET(RL_MII_CLK);
	DELAY(1);

	/*
	 * Now try reading data bits. If the ack failed, we still
	 * need to clock through 16 cycles to keep the PHY(s) in sync.
	 */
	if (ack) {
		for(i = 0; i < 16; i++) {
			MII_CLR(RL_MII_CLK);
			DELAY(1);
			MII_SET(RL_MII_CLK);
			DELAY(1);
		}
		goto fail;
	}

	for (i = 0x8000; i; i >>= 1) {
		MII_CLR(RL_MII_CLK);
		DELAY(1);
		if (!ack) {
			if (CSR_READ_2(sc, RL_MII) & RL_MII_DATAIN)
				frame->mii_data |= i;
			DELAY(1);
		}
		MII_SET(RL_MII_CLK);
		DELAY(1);
	}

fail:
	MII_CLR(RL_MII_CLK);
	DELAY(1);
	MII_SET(RL_MII_CLK);
	DELAY(1);

	return (ack ? 1 : 0);
}

/*
 * Write to a PHY register through the MII.
 */
static int
rl_mii_writereg(struct rl_softc *sc, struct rl_mii_frame *frame)
{

	/* Set up frame for TX. */
	frame->mii_stdelim = RL_MII_STARTDELIM;
	frame->mii_opcode = RL_MII_WRITEOP;
	frame->mii_turnaround = RL_MII_TURNAROUND;

	/* Turn on data output. */
	MII_SET(RL_MII_DIR);

	rl_mii_sync(sc);

	rl_mii_send(sc, frame->mii_stdelim, 2);
	rl_mii_send(sc, frame->mii_opcode, 2);
	rl_mii_send(sc, frame->mii_phyaddr, 5);
	rl_mii_send(sc, frame->mii_regaddr, 5);
	rl_mii_send(sc, frame->mii_turnaround, 2);
	rl_mii_send(sc, frame->mii_data, 16);

	/* Idle bit. */
	MII_SET(RL_MII_CLK);
	DELAY(1);
	MII_CLR(RL_MII_CLK);
	DELAY(1);

	/* Turn off xmit. */
	MII_CLR(RL_MII_DIR);

	return (0);
}

static int
rl_miibus_readreg(device_t dev, int phy, int reg)
{
	struct rl_softc		*sc;
	struct rl_mii_frame	frame;
	uint16_t		rval = 0;
	uint16_t		rl8139_reg = 0;

	sc = device_get_softc(dev);

	if (sc->rl_type == RL_8139) {
		/* Pretend the internal PHY is only at address 0 */
		if (phy) {
			return (0);
		}
		switch (reg) {
		case MII_BMCR:
			rl8139_reg = RL_BMCR;
			break;
		case MII_BMSR:
			rl8139_reg = RL_BMSR;
			break;
		case MII_ANAR:
			rl8139_reg = RL_ANAR;
			break;
		case MII_ANER:
			rl8139_reg = RL_ANER;
			break;
		case MII_ANLPAR:
			rl8139_reg = RL_LPAR;
			break;
		case MII_PHYIDR1:
		case MII_PHYIDR2:
			return (0);
		/*
		 * Allow the rlphy driver to read the media status
		 * register. If we have a link partner which does not
		 * support NWAY, this is the register which will tell
		 * us the results of parallel detection.
		 */
		case RL_MEDIASTAT:
			rval = CSR_READ_1(sc, RL_MEDIASTAT);
			return (rval);
		default:
			device_printf(sc->rl_dev, "bad phy register\n");
			return (0);
		}
		rval = CSR_READ_2(sc, rl8139_reg);
		return (rval);
	}

	bzero((char *)&frame, sizeof(frame));
	frame.mii_phyaddr = phy;
	frame.mii_regaddr = reg;
	rl_mii_readreg(sc, &frame);

	return (frame.mii_data);
}

static int
rl_miibus_writereg(device_t dev, int phy, int reg, int data)
{
	struct rl_softc		*sc;
	struct rl_mii_frame	frame;
	uint16_t		rl8139_reg = 0;

	sc = device_get_softc(dev);

	if (sc->rl_type == RL_8139) {
		/* Pretend the internal PHY is only at address 0 */
		if (phy) {
			return (0);
		}
		switch (reg) {
		case MII_BMCR:
			rl8139_reg = RL_BMCR;
			break;
		case MII_BMSR:
			rl8139_reg = RL_BMSR;
			break;
		case MII_ANAR:
			rl8139_reg = RL_ANAR;
			break;
		case MII_ANER:
			rl8139_reg = RL_ANER;
			break;
		case MII_ANLPAR:
			rl8139_reg = RL_LPAR;
			break;
		case MII_PHYIDR1:
		case MII_PHYIDR2:
			return (0);
			break;
		default:
			device_printf(sc->rl_dev, "bad phy register\n");
			return (0);
		}
		CSR_WRITE_2(sc, rl8139_reg, data);
		return (0);
	}

	bzero((char *)&frame, sizeof(frame));
	frame.mii_phyaddr = phy;
	frame.mii_regaddr = reg;
	frame.mii_data = data;
	rl_mii_writereg(sc, &frame);

	return (0);
}

static void
rl_miibus_statchg(device_t dev)
{
}

/*
 * Program the 64-bit multicast hash filter.
 */
static void
rl_setmulti(struct rl_softc *sc)
{
	struct ifnet		*ifp = sc->rl_ifp;
	int			h = 0;
	uint32_t		hashes[2] = { 0, 0 };
	struct ifmultiaddr	*ifma;
	uint32_t		rxfilt;
	int			mcnt = 0;

	RL_LOCK_ASSERT(sc);

	rxfilt = CSR_READ_4(sc, RL_RXCFG);

	if (ifp->if_flags & IFF_ALLMULTI || ifp->if_flags & IFF_PROMISC) {
		rxfilt |= RL_RXCFG_RX_MULTI;
		CSR_WRITE_4(sc, RL_RXCFG, rxfilt);
		CSR_WRITE_4(sc, RL_MAR0, 0xFFFFFFFF);
		CSR_WRITE_4(sc, RL_MAR4, 0xFFFFFFFF);
		return;
	}

	/* first, zot all the existing hash bits */
	CSR_WRITE_4(sc, RL_MAR0, 0);
	CSR_WRITE_4(sc, RL_MAR4, 0);

	/* now program new ones */
	IF_ADDR_LOCK(ifp);
	TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) {
		if (ifma->ifma_addr->sa_family != AF_LINK)
			continue;
		h = ether_crc32_be(LLADDR((struct sockaddr_dl *)
		    ifma->ifma_addr), ETHER_ADDR_LEN) >> 26;
		if (h < 32)
			hashes[0] |= (1 << h);
		else
			hashes[1] |= (1 << (h - 32));
		mcnt++;
	}
	IF_ADDR_UNLOCK(ifp);

	if (mcnt)
		rxfilt |= RL_RXCFG_RX_MULTI;
	else
		rxfilt &= ~RL_RXCFG_RX_MULTI;

	CSR_WRITE_4(sc, RL_RXCFG, rxfilt);
	CSR_WRITE_4(sc, RL_MAR0, hashes[0]);
	CSR_WRITE_4(sc, RL_MAR4, hashes[1]);
}

static void
rl_reset(struct rl_softc *sc)
{
	register int		i;

	RL_LOCK_ASSERT(sc);

	CSR_WRITE_1(sc, RL_COMMAND, RL_CMD_RESET);

	for (i = 0; i < RL_TIMEOUT; i++) {
		DELAY(10);
		if (!(CSR_READ_1(sc, RL_COMMAND) & RL_CMD_RESET))
			break;
	}
	if (i == RL_TIMEOUT)
		device_printf(sc->rl_dev, "reset never completed!\n");
}

/*
 * Probe for a RealTek 8129/8139 chip. Check the PCI vendor and device
 * IDs against our list and return a device name if we find a match.
 */
static int
rl_probe(device_t dev)
{
	struct rl_type		*t;
	uint16_t		devid, revid, vendor;
	int			i;
	
	vendor = pci_get_vendor(dev);
	devid = pci_get_device(dev);
	revid = pci_get_revid(dev);

	if (vendor == RT_VENDORID && devid == RT_DEVICEID_8139) {
		if (revid == 0x20) {
			/* 8139C+, let re(4) take care of this device. */
			return (ENXIO);
		}
	}
	t = rl_devs;
	for (i = 0; i < sizeof(rl_devs) / sizeof(rl_devs[0]); i++, t++) {
		if (vendor == t->rl_vid && devid == t->rl_did) {
			device_set_desc(dev, t->rl_name);
			return (BUS_PROBE_DEFAULT);
		}
	}

	return (ENXIO);
}

struct rl_dmamap_arg {
	bus_addr_t	rl_busaddr;
};

static void
rl_dmamap_cb(void *arg, bus_dma_segment_t *segs, int nsegs, int error)
{
	struct rl_dmamap_arg	*ctx;

	if (error != 0)
		return;

	KASSERT(nsegs == 1, ("%s: %d segments returned!", __func__, nsegs));

        ctx = (struct rl_dmamap_arg *)arg;
        ctx->rl_busaddr = segs[0].ds_addr;
}

/*
 * Attach the interface. Allocate softc structures, do ifmedia
 * setup and ethernet/BPF attach.
 */
static int
rl_attach(device_t dev)
{
	uint8_t			eaddr[ETHER_ADDR_LEN];
	uint16_t		as[3];
	struct ifnet		*ifp;
	struct rl_softc		*sc;
	struct rl_type		*t;
	int			error = 0, i, rid;
	int			unit;
	uint16_t		rl_did = 0;

	sc = device_get_softc(dev);
	unit = device_get_unit(dev);
	sc->rl_dev = dev;

	mtx_init(&sc->rl_mtx, device_get_nameunit(dev), MTX_NETWORK_LOCK,
	    MTX_DEF);
	callout_init_mtx(&sc->rl_stat_callout, &sc->rl_mtx, 0);

	pci_enable_busmaster(dev);

	/* Map control/status registers. */
	rid = RL_RID;
	sc->rl_res = bus_alloc_resource_any(dev, RL_RES, &rid, RF_ACTIVE);

	if (sc->rl_res == NULL) {
		device_printf(dev, "couldn't map ports/memory\n");
		error = ENXIO;
		goto fail;
	}

#ifdef notdef
	/*
	 * Detect the Realtek 8139B. For some reason, this chip is very
	 * unstable when left to autoselect the media
	 * The best workaround is to set the device to the required
	 * media type or to set it to the 10 Meg speed.
	 */
	if ((rman_get_end(sc->rl_res) - rman_get_start(sc->rl_res)) == 0xFF)
		device_printf(dev,
"Realtek 8139B detected. Warning, this may be unstable in autoselect mode\n");
#endif

	sc->rl_btag = rman_get_bustag(sc->rl_res);
	sc->rl_bhandle = rman_get_bushandle(sc->rl_res);

	/* Allocate interrupt */
	rid = 0;
	sc->rl_irq[0] = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid,
	    RF_SHAREABLE | RF_ACTIVE);

	if (sc->rl_irq[0] == NULL) {
		device_printf(dev, "couldn't map interrupt\n");
		error = ENXIO;
		goto fail;
	}

	/*
	 * Reset the adapter. Only take the lock here as it's needed in
	 * order to call rl_reset().
	 */
	RL_LOCK(sc);
	rl_reset(sc);
	RL_UNLOCK(sc);

	sc->rl_eecmd_read = RL_EECMD_READ_6BIT;
	rl_read_eeprom(sc, (uint8_t *)&rl_did, 0, 1, 0);
	if (rl_did != 0x8129)
		sc->rl_eecmd_read = RL_EECMD_READ_8BIT;

	/*
	 * Get station address from the EEPROM.
	 */
	rl_read_eeprom(sc, (uint8_t *)as, RL_EE_EADDR, 3, 0);
	for (i = 0; i < 3; i++) {
		eaddr[(i * 2) + 0] = as[i] & 0xff;
		eaddr[(i * 2) + 1] = as[i] >> 8;
	}

	/*
	 * Now read the exact device type from the EEPROM to find
	 * out if it's an 8129 or 8139.
	 */
	rl_read_eeprom(sc, (uint8_t *)&rl_did, RL_EE_PCI_DID, 1, 0);

	t = rl_devs;
	sc->rl_type = 0;
	while(t->rl_name != NULL) {
		if (rl_did == t->rl_did) {
			sc->rl_type = t->rl_basetype;
			break;
		}
		t++;
	}

	if (sc->rl_type == 0) {
		device_printf(dev, "unknown device ID: %x\n", rl_did);
		error = ENXIO;
		goto fail;
	}

	if ((error = rl_dma_alloc(sc)) != 0)
		goto fail;

	ifp = sc->rl_ifp = if_alloc(IFT_ETHER);
	if (ifp == NULL) {
		device_printf(dev, "can not if_alloc()\n");
		error = ENOSPC;
		goto fail;
	}

	/* Do MII setup */
	if (mii_phy_probe(dev, &sc->rl_miibus,
	    rl_ifmedia_upd, rl_ifmedia_sts)) {
		device_printf(dev, "MII without any phy!\n");
		error = ENXIO;
		goto fail;
	}

	ifp->if_softc = sc;
	if_initname(ifp, device_get_name(dev), device_get_unit(dev));
	ifp->if_mtu = ETHERMTU;
	ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST;
	ifp->if_ioctl = rl_ioctl;
	ifp->if_start = rl_start;
	ifp->if_init = rl_init;
	ifp->if_capabilities = IFCAP_VLAN_MTU;
	ifp->if_capenable = ifp->if_capabilities;
#ifdef DEVICE_POLLING
	ifp->if_capabilities |= IFCAP_POLLING;
#endif
	IFQ_SET_MAXLEN(&ifp->if_snd, IFQ_MAXLEN);
	ifp->if_snd.ifq_drv_maxlen = IFQ_MAXLEN;
	IFQ_SET_READY(&ifp->if_snd);

	/*
	 * Call MI attach routine.
	 */
	ether_ifattach(ifp, eaddr);

	/* Hook interrupt last to avoid having to lock softc */
	error = bus_setup_intr(dev, sc->rl_irq[0], INTR_TYPE_NET | INTR_MPSAFE,
	    NULL, rl_intr, sc, &sc->rl_intrhand[0]);
	if (error) {
		device_printf(sc->rl_dev, "couldn't set up irq\n");
		ether_ifdetach(ifp);
	}

fail:
	if (error)
		rl_detach(dev);

	return (error);
}

/*
 * Shutdown hardware and free up resources. This can be called any
 * time after the mutex has been initialized. It is called in both
 * the error case in attach and the normal detach case so it needs
 * to be careful about only freeing resources that have actually been
 * allocated.
 */
static int
rl_detach(device_t dev)
{
	struct rl_softc		*sc;
	struct ifnet		*ifp;

	sc = device_get_softc(dev);
	ifp = sc->rl_ifp;

	KASSERT(mtx_initialized(&sc->rl_mtx), ("rl mutex not initialized"));

#ifdef DEVICE_POLLING
	if (ifp->if_capenable & IFCAP_POLLING)
		ether_poll_deregister(ifp);
#endif
	/* These should only be active if attach succeeded */
	if (device_is_attached(dev)) {
		RL_LOCK(sc);
		rl_stop(sc);
		RL_UNLOCK(sc);
		callout_drain(&sc->rl_stat_callout);
		ether_ifdetach(ifp);
	}
#if 0
	sc->suspended = 1;
#endif
	if (sc->rl_miibus)
		device_delete_child(dev, sc->rl_miibus);
	bus_generic_detach(dev);

	if (sc->rl_intrhand[0])
		bus_teardown_intr(dev, sc->rl_irq[0], sc->rl_intrhand[0]);
	if (sc->rl_irq[0])
		bus_release_resource(dev, SYS_RES_IRQ, 0, sc->rl_irq[0]);
	if (sc->rl_res)
		bus_release_resource(dev, RL_RES, RL_RID, sc->rl_res);

	if (ifp)
		if_free(ifp);

	rl_dma_free(sc);

	mtx_destroy(&sc->rl_mtx);

	return (0);
}

static int
rl_dma_alloc(struct rl_softc *sc)
{
	struct rl_dmamap_arg	ctx;
	int			error, i;

	/*
	 * Allocate the parent bus DMA tag appropriate for PCI.
	 */
	error = bus_dma_tag_create(bus_get_dma_tag(sc->rl_dev),	/* parent */
	    1, 0,			/* alignment, boundary */
	    BUS_SPACE_MAXADDR_32BIT,	/* lowaddr */
	    BUS_SPACE_MAXADDR,		/* highaddr */
	    NULL, NULL,			/* filter, filterarg */
	    BUS_SPACE_MAXSIZE_32BIT, 0,	/* maxsize, nsegments */
	    BUS_SPACE_MAXSIZE_32BIT,	/* maxsegsize */
	    0,				/* flags */
	    NULL, NULL,			/* lockfunc, lockarg */
	    &sc->rl_parent_tag);
	if (error) {
                device_printf(sc->rl_dev,
		    "failed to create parent DMA tag.\n");
		goto fail;
	}
	/* Create DMA tag for Rx memory block. */
	error = bus_dma_tag_create(sc->rl_parent_tag,	/* parent */
	    RL_RX_8139_BUF_ALIGN, 0,	/* alignment, boundary */
	    BUS_SPACE_MAXADDR,		/* lowaddr */
	    BUS_SPACE_MAXADDR,		/* highaddr */
	    NULL, NULL,			/* filter, filterarg */
	    RL_RXBUFLEN + RL_RX_8139_BUF_GUARD_SZ, 1,	/* maxsize,nsegments */
	    RL_RXBUFLEN + RL_RX_8139_BUF_GUARD_SZ,	/* maxsegsize */
	    0,				/* flags */
	    NULL, NULL,			/* lockfunc, lockarg */
	    &sc->rl_cdata.rl_rx_tag);
	if (error) {
                device_printf(sc->rl_dev,
		    "failed to create Rx memory block DMA tag.\n");
		goto fail;
	}
	/* Create DMA tag for Tx buffer. */
	error = bus_dma_tag_create(sc->rl_parent_tag,	/* parent */
	    RL_TX_8139_BUF_ALIGN, 0,	/* alignment, boundary */
	    BUS_SPACE_MAXADDR,		/* lowaddr */
	    BUS_SPACE_MAXADDR,		/* highaddr */
	    NULL, NULL,			/* filter, filterarg */
	    MCLBYTES, 1,		/* maxsize, nsegments */
	    MCLBYTES,			/* maxsegsize */
	    0,				/* flags */
	    NULL, NULL,			/* lockfunc, lockarg */
	    &sc->rl_cdata.rl_tx_tag);
	if (error) {
                device_printf(sc->rl_dev, "failed to create Tx DMA tag.\n");
		goto fail;
	}

	/*
	 * Allocate DMA'able memory and load DMA map for Rx memory block.
	 */
	error = bus_dmamem_alloc(sc->rl_cdata.rl_rx_tag,
	    (void **)&sc->rl_cdata.rl_rx_buf, BUS_DMA_WAITOK |
	    BUS_DMA_COHERENT | BUS_DMA_ZERO, &sc->rl_cdata.rl_rx_dmamap);
	if (error != 0) {
		device_printf(sc->rl_dev,
		    "failed to allocate Rx DMA memory block.\n");
		goto fail;
	}
	ctx.rl_busaddr = 0;
	error = bus_dmamap_load(sc->rl_cdata.rl_rx_tag,
	    sc->rl_cdata.rl_rx_dmamap, sc->rl_cdata.rl_rx_buf,
	    RL_RXBUFLEN + RL_RX_8139_BUF_GUARD_SZ, rl_dmamap_cb, &ctx,
	    BUS_DMA_NOWAIT);
	if (error != 0 || ctx.rl_busaddr == 0) {
		device_printf(sc->rl_dev,
		    "could not load Rx DMA memory block.\n");
		goto fail;
	}
	sc->rl_cdata.rl_rx_buf_paddr = ctx.rl_busaddr;

	/* Create DMA maps for Tx buffers. */
	for (i = 0; i < RL_TX_LIST_CNT; i++) {
		sc->rl_cdata.rl_tx_chain[i] = NULL;
		sc->rl_cdata.rl_tx_dmamap[i] = NULL;
		error = bus_dmamap_create(sc->rl_cdata.rl_tx_tag, 0,
		    &sc->rl_cdata.rl_tx_dmamap[i]);
		if (error != 0) {
			device_printf(sc->rl_dev,
			    "could not create Tx dmamap.\n");
			goto fail;
		}
	}

	/* Leave a few bytes before the start of the RX ring buffer. */
	sc->rl_cdata.rl_rx_buf_ptr = sc->rl_cdata.rl_rx_buf;
	sc->rl_cdata.rl_rx_buf += RL_RX_8139_BUF_RESERVE;

fail:
	return (error);
}

static void
rl_dma_free(struct rl_softc *sc)
{
	int			i;

	/* Rx memory block. */
	if (sc->rl_cdata.rl_rx_tag != NULL) {
		if (sc->rl_cdata.rl_rx_dmamap != NULL)
			bus_dmamap_unload(sc->rl_cdata.rl_rx_tag,
			    sc->rl_cdata.rl_rx_dmamap);
		if (sc->rl_cdata.rl_rx_dmamap != NULL &&
		    sc->rl_cdata.rl_rx_buf_ptr != NULL)
			bus_dmamem_free(sc->rl_cdata.rl_rx_tag,
			    sc->rl_cdata.rl_rx_buf_ptr,
			    sc->rl_cdata.rl_rx_dmamap);
		sc->rl_cdata.rl_rx_buf_ptr = NULL;
		sc->rl_cdata.rl_rx_buf = NULL;
		sc->rl_cdata.rl_rx_dmamap = NULL;
		bus_dma_tag_destroy(sc->rl_cdata.rl_rx_tag);
		sc->rl_cdata.rl_tx_tag = NULL;
	}

	/* Tx buffers. */
	if (sc->rl_cdata.rl_tx_tag != NULL) {
		for (i = 0; i < RL_TX_LIST_CNT; i++) {
			if (sc->rl_cdata.rl_tx_dmamap[i] != NULL) {
				bus_dmamap_destroy(
				    sc->rl_cdata.rl_tx_tag,
				    sc->rl_cdata.rl_tx_dmamap[i]);
				sc->rl_cdata.rl_tx_dmamap[i] = NULL;
			}
		bus_dma_tag_destroy(sc->rl_cdata.rl_tx_tag);
		sc->rl_cdata.rl_tx_tag = NULL;
		}
	}

	if (sc->rl_parent_tag != NULL) {
		bus_dma_tag_destroy(sc->rl_parent_tag);
		sc->rl_parent_tag = NULL;
	}
}

/*
 * Initialize the transmit descriptors.
 */
static int
rl_list_tx_init(struct rl_softc *sc)
{
	struct rl_chain_data	*cd;
	int			i;

	RL_LOCK_ASSERT(sc);

	cd = &sc->rl_cdata;
	for (i = 0; i < RL_TX_LIST_CNT; i++) {
		cd->rl_tx_chain[i] = NULL;
		CSR_WRITE_4(sc,
		    RL_TXADDR0 + (i * sizeof(uint32_t)), 0x0000000);
	}

	sc->rl_cdata.cur_tx = 0;
	sc->rl_cdata.last_tx = 0;

	return (0);
}

static int
rl_list_rx_init(struct rl_softc *sc)
{

	RL_LOCK_ASSERT(sc);

	bzero(sc->rl_cdata.rl_rx_buf_ptr,
	    RL_RXBUFLEN + RL_RX_8139_BUF_GUARD_SZ);
	bus_dmamap_sync(sc->rl_cdata.rl_tx_tag, sc->rl_cdata.rl_rx_dmamap,
	    BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE);

	return (0);
}

/*
 * A frame has been uploaded: pass the resulting mbuf chain up to
 * the higher level protocols.
 *
 * You know there's something wrong with a PCI bus-master chip design
 * when you have to use m_devget().
 *
 * The receive operation is badly documented in the datasheet, so I'll
 * attempt to document it here. The driver provides a buffer area and
 * places its base address in the RX buffer start address register.
 * The chip then begins copying frames into the RX buffer. Each frame
 * is preceded by a 32-bit RX status word which specifies the length
 * of the frame and certain other status bits. Each frame (starting with
 * the status word) is also 32-bit aligned. The frame length is in the
 * first 16 bits of the status word; the lower 15 bits correspond with
 * the 'rx status register' mentioned in the datasheet.
 *
 * Note: to make the Alpha happy, the frame payload needs to be aligned
 * on a 32-bit boundary. To achieve this, we pass RL_ETHER_ALIGN (2 bytes)
 * as the offset argument to m_devget().
 */
static void
rl_rxeof(struct rl_softc *sc)
{
	struct mbuf		*m;
	struct ifnet		*ifp = sc->rl_ifp;
	uint8_t			*rxbufpos;
	int			total_len = 0;
	int			wrap = 0;
	uint32_t		rxstat;
	uint16_t		cur_rx;
	uint16_t		limit;
	uint16_t		max_bytes, rx_bytes = 0;

	RL_LOCK_ASSERT(sc);

	bus_dmamap_sync(sc->rl_cdata.rl_rx_tag, sc->rl_cdata.rl_rx_dmamap,
	    BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE);

	cur_rx = (CSR_READ_2(sc, RL_CURRXADDR) + 16) % RL_RXBUFLEN;

	/* Do not try to read past this point. */
	limit = CSR_READ_2(sc, RL_CURRXBUF) % RL_RXBUFLEN;

	if (limit < cur_rx)
		max_bytes = (RL_RXBUFLEN - cur_rx) + limit;
	else
		max_bytes = limit - cur_rx;

	while((CSR_READ_1(sc, RL_COMMAND) & RL_CMD_EMPTY_RXBUF) == 0) {
#ifdef DEVICE_POLLING
		if (ifp->if_capenable & IFCAP_POLLING) {
			if (sc->rxcycles <= 0)
				break;
			sc->rxcycles--;
		}
#endif
		rxbufpos = sc->rl_cdata.rl_rx_buf + cur_rx;
		rxstat = le32toh(*(uint32_t *)rxbufpos);

		/*
		 * Here's a totally undocumented fact for you. When the
		 * RealTek chip is in the process of copying a packet into
		 * RAM for you, the length will be 0xfff0. If you spot a
		 * packet header with this value, you need to stop. The
		 * datasheet makes absolutely no mention of this and
		 * RealTek should be shot for this.
		 */
		total_len = rxstat >> 16;
		if (total_len == RL_RXSTAT_UNFINISHED)
			break;

		if (!(rxstat & RL_RXSTAT_RXOK) ||
		    total_len < ETHER_MIN_LEN ||
		    total_len > ETHER_MAX_LEN + ETHER_VLAN_ENCAP_LEN) {
			ifp->if_ierrors++;
			rl_init_locked(sc);
			return;
		}

		/* No errors; receive the packet. */
		rx_bytes += total_len + 4;

		/*
		 * XXX The RealTek chip includes the CRC with every
		 * received frame, and there's no way to turn this
		 * behavior off (at least, I can't find anything in
		 * the manual that explains how to do it) so we have
		 * to trim off the CRC manually.
		 */
		total_len -= ETHER_CRC_LEN;

		/*
		 * Avoid trying to read more bytes than we know
		 * the chip has prepared for us.
		 */
		if (rx_bytes > max_bytes)
			break;

		rxbufpos = sc->rl_cdata.rl_rx_buf +
			((cur_rx + sizeof(uint32_t)) % RL_RXBUFLEN);
		if (rxbufpos == (sc->rl_cdata.rl_rx_buf + RL_RXBUFLEN))
			rxbufpos = sc->rl_cdata.rl_rx_buf;

		wrap = (sc->rl_cdata.rl_rx_buf + RL_RXBUFLEN) - rxbufpos;
		if (total_len > wrap) {
			m = m_devget(rxbufpos, total_len, RL_ETHER_ALIGN, ifp,
			    NULL);
			if (m == NULL) {
				ifp->if_ierrors++;
			} else {
				m_copyback(m, wrap, total_len - wrap,
					sc->rl_cdata.rl_rx_buf);
			}
			cur_rx = (total_len - wrap + ETHER_CRC_LEN);
		} else {
			m = m_devget(rxbufpos, total_len, RL_ETHER_ALIGN, ifp,
			    NULL);
			if (m == NULL)
				ifp->if_ierrors++;
			cur_rx += total_len + 4 + ETHER_CRC_LEN;
		}

		/* Round up to 32-bit boundary. */
		cur_rx = (cur_rx + 3) & ~3;
		CSR_WRITE_2(sc, RL_CURRXADDR, cur_rx - 16);

		if (m == NULL)
			continue;

		ifp->if_ipackets++;
		RL_UNLOCK(sc);
		(*ifp->if_input)(ifp, m);
		RL_LOCK(sc);
	}

	/* No need to sync Rx memory block as we didn't mofify it. */
}

/*
 * A frame was downloaded to the chip. It's safe for us to clean up
 * the list buffers.
 */
static void
rl_txeof(struct rl_softc *sc)
{
	struct ifnet		*ifp = sc->rl_ifp;
	uint32_t		txstat;

	RL_LOCK_ASSERT(sc);

	/*
	 * Go through our tx list and free mbufs for those
	 * frames that have been uploaded.
	 */
	do {
		if (RL_LAST_TXMBUF(sc) == NULL)
			break;
		txstat = CSR_READ_4(sc, RL_LAST_TXSTAT(sc));
		if (!(txstat & (RL_TXSTAT_TX_OK|
		    RL_TXSTAT_TX_UNDERRUN|RL_TXSTAT_TXABRT)))
			break;

		ifp->if_collisions += (txstat & RL_TXSTAT_COLLCNT) >> 24;

		bus_dmamap_sync(sc->rl_cdata.rl_tx_tag, RL_LAST_DMAMAP(sc),
		    BUS_DMASYNC_POSTWRITE);
		bus_dmamap_unload(sc->rl_cdata.rl_tx_tag, RL_LAST_DMAMAP(sc));
		m_freem(RL_LAST_TXMBUF(sc));
		RL_LAST_TXMBUF(sc) = NULL;
		/*
		 * If there was a transmit underrun, bump the TX threshold.
		 * Make sure not to overflow the 63 * 32byte we can address
		 * with the 6 available bit.
		 */
		if ((txstat & RL_TXSTAT_TX_UNDERRUN) &&
		    (sc->rl_txthresh < 2016))
			sc->rl_txthresh += 32;
		if (txstat & RL_TXSTAT_TX_OK)
			ifp->if_opackets++;
		else {
			int			oldthresh;
			ifp->if_oerrors++;
			if ((txstat & RL_TXSTAT_TXABRT) ||
			    (txstat & RL_TXSTAT_OUTOFWIN))
				CSR_WRITE_4(sc, RL_TXCFG, RL_TXCFG_CONFIG);
			oldthresh = sc->rl_txthresh;
			/* error recovery */
			rl_reset(sc);
			rl_init_locked(sc);
			/* restore original threshold */
			sc->rl_txthresh = oldthresh;
			return;
		}
		RL_INC(sc->rl_cdata.last_tx);
		ifp->if_drv_flags &= ~IFF_DRV_OACTIVE;
	} while (sc->rl_cdata.last_tx != sc->rl_cdata.cur_tx);

	if (RL_LAST_TXMBUF(sc) == NULL)
		sc->rl_watchdog_timer = 0;
}

static void
rl_tick(void *xsc)
{
	struct rl_softc		*sc = xsc;
	struct mii_data		*mii;

	RL_LOCK_ASSERT(sc);
	mii = device_get_softc(sc->rl_miibus);
	mii_tick(mii);

	rl_watchdog(sc);

	callout_reset(&sc->rl_stat_callout, hz, rl_tick, sc);
}

#ifdef DEVICE_POLLING
static void
rl_poll(struct ifnet *ifp, enum poll_cmd cmd, int count)
{
	struct rl_softc *sc = ifp->if_softc;

	RL_LOCK(sc);
	if (ifp->if_drv_flags & IFF_DRV_RUNNING)
		rl_poll_locked(ifp, cmd, count);
	RL_UNLOCK(sc);
}

static void
rl_poll_locked(struct ifnet *ifp, enum poll_cmd cmd, int count)
{
	struct rl_softc *sc = ifp->if_softc;

	RL_LOCK_ASSERT(sc);

	sc->rxcycles = count;
	rl_rxeof(sc);
	rl_txeof(sc);

	if (!IFQ_DRV_IS_EMPTY(&ifp->if_snd))
		rl_start_locked(ifp);

	if (cmd == POLL_AND_CHECK_STATUS) {
		uint16_t	status;

		/* We should also check the status register. */
		status = CSR_READ_2(sc, RL_ISR);
		if (status == 0xffff)
			return;
		if (status != 0)
			CSR_WRITE_2(sc, RL_ISR, status);

		/* XXX We should check behaviour on receiver stalls. */

		if (status & RL_ISR_SYSTEM_ERR) {
			rl_reset(sc);
			rl_init_locked(sc);
		}
	}
}
#endif /* DEVICE_POLLING */

static void
rl_intr(void *arg)
{
	struct rl_softc		*sc = arg;
	struct ifnet		*ifp = sc->rl_ifp;
	uint16_t		status;

	RL_LOCK(sc);

	if (sc->suspended)
		goto done_locked;

#ifdef DEVICE_POLLING
	if  (ifp->if_capenable & IFCAP_POLLING)
		goto done_locked;
#endif

	for (;;) {
		status = CSR_READ_2(sc, RL_ISR);
		/* If the card has gone away, the read returns 0xffff. */
		if (status == 0xffff)
			break;
		if (status != 0)
			CSR_WRITE_2(sc, RL_ISR, status);
		if ((status & RL_INTRS) == 0)
			break;
		if (status & RL_ISR_RX_OK)
			rl_rxeof(sc);
		if (status & RL_ISR_RX_ERR)
			rl_rxeof(sc);
		if ((status & RL_ISR_TX_OK) || (status & RL_ISR_TX_ERR))
			rl_txeof(sc);
		if (status & RL_ISR_SYSTEM_ERR) {
			rl_reset(sc);
			rl_init_locked(sc);
		}
	}

	if (!IFQ_DRV_IS_EMPTY(&ifp->if_snd))
		rl_start_locked(ifp);

done_locked:
	RL_UNLOCK(sc);
}

/*
 * Encapsulate an mbuf chain in a descriptor by coupling the mbuf data
 * pointers to the fragment pointers.
 */
static int
rl_encap(struct rl_softc *sc, struct mbuf **m_head)
{
	struct mbuf		*m;
	bus_dma_segment_t	txsegs[1];
	int			error, nsegs, padlen;

	RL_LOCK_ASSERT(sc);

	m = *m_head;
	padlen = 0;
	/*
	 * Hardware doesn't auto-pad, so we have to make sure
	 * pad short frames out to the minimum frame length.
	 */
	if (m->m_pkthdr.len < RL_MIN_FRAMELEN)
		padlen = RL_MIN_FRAMELEN - m->m_pkthdr.len;
	/*
	 * The RealTek is brain damaged and wants longword-aligned
	 * TX buffers, plus we can only have one fragment buffer
	 * per packet. We have to copy pretty much all the time.
	 */
	if (m->m_next != NULL || (mtod(m, uintptr_t) & 3) != 0 ||
	    (padlen > 0 && M_TRAILINGSPACE(m) < padlen)) {
		m = m_defrag(*m_head, M_DONTWAIT);
		if (m == NULL) {
			m_freem(*m_head);
			*m_head = NULL;
			return (ENOMEM);
		}
	}
	*m_head = m;

	if (padlen > 0) {
		/*
		 * Make security concious people happy: zero out the
		 * bytes in the pad area, since we don't know what
		 * this mbuf cluster buffer's previous user might
		 * have left in it.
		 */
		bzero(mtod(m, char *) + m->m_pkthdr.len, padlen);
		m->m_pkthdr.len += padlen;
		m->m_len = m->m_pkthdr.len;
	}

	error = bus_dmamap_load_mbuf_sg(sc->rl_cdata.rl_tx_tag,
	    RL_CUR_DMAMAP(sc), m, txsegs, &nsegs, 0);
	if (error != 0)
		return (error);
	if (nsegs == 0) {
		m_freem(*m_head);
		*m_head = NULL;
		return (EIO);
	}

	RL_CUR_TXMBUF(sc) = m;
	bus_dmamap_sync(sc->rl_cdata.rl_tx_tag, RL_CUR_DMAMAP(sc),
	    BUS_DMASYNC_PREWRITE);
	CSR_WRITE_4(sc, RL_CUR_TXADDR(sc), RL_ADDR_LO(txsegs[0].ds_addr));

	return (0);
}

/*
 * Main transmit routine.
 */
static void
rl_start(struct ifnet *ifp)
{
	struct rl_softc		*sc = ifp->if_softc;

	RL_LOCK(sc);
	rl_start_locked(ifp);
	RL_UNLOCK(sc);
}

static void
rl_start_locked(struct ifnet *ifp)
{
	struct rl_softc		*sc = ifp->if_softc;
	struct mbuf		*m_head = NULL;

	RL_LOCK_ASSERT(sc);

	while (RL_CUR_TXMBUF(sc) == NULL) {

		IFQ_DRV_DEQUEUE(&ifp->if_snd, m_head);

		if (m_head == NULL)
			break;

		if (rl_encap(sc, &m_head)) {
			if (m_head == NULL)
				break;
			IFQ_DRV_PREPEND(&ifp->if_snd, m_head);
			ifp->if_drv_flags |= IFF_DRV_OACTIVE;
			break;
		}

		/* Pass a copy of this mbuf chain to the bpf subsystem. */
		BPF_MTAP(ifp, RL_CUR_TXMBUF(sc));

		/* Transmit the frame. */
		CSR_WRITE_4(sc, RL_CUR_TXSTAT(sc),
		    RL_TXTHRESH(sc->rl_txthresh) |
		    RL_CUR_TXMBUF(sc)->m_pkthdr.len);

		RL_INC(sc->rl_cdata.cur_tx);

		/* Set a timeout in case the chip goes out to lunch. */
		sc->rl_watchdog_timer = 5;
	}

	/*
	 * We broke out of the loop because all our TX slots are
	 * full. Mark the NIC as busy until it drains some of the
	 * packets from the queue.
	 */
	if (RL_CUR_TXMBUF(sc) != NULL)
		ifp->if_drv_flags |= IFF_DRV_OACTIVE;
}

static void
rl_init(void *xsc)
{
	struct rl_softc		*sc = xsc;

	RL_LOCK(sc);
	rl_init_locked(sc);
	RL_UNLOCK(sc);
}

static void
rl_init_locked(struct rl_softc *sc)
{
	struct ifnet		*ifp = sc->rl_ifp;
	struct mii_data		*mii;
	uint32_t		rxcfg = 0;
	uint32_t		eaddr[2];

	RL_LOCK_ASSERT(sc);

	mii = device_get_softc(sc->rl_miibus);

	/*
	 * Cancel pending I/O and free all RX/TX buffers.
	 */
	rl_stop(sc);

	/*
	 * Init our MAC address.  Even though the chipset
	 * documentation doesn't mention it, we need to enter "Config
	 * register write enable" mode to modify the ID registers.
	 */
	CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_WRITECFG);
	bzero(eaddr, sizeof(eaddr));
	bcopy(IF_LLADDR(sc->rl_ifp), eaddr, ETHER_ADDR_LEN);
	CSR_WRITE_STREAM_4(sc, RL_IDR0, eaddr[0]);
	CSR_WRITE_STREAM_4(sc, RL_IDR4, eaddr[1]);
	CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_OFF);

	/* Init the RX memory block pointer register. */
	CSR_WRITE_4(sc, RL_RXADDR, sc->rl_cdata.rl_rx_buf_paddr +
	    RL_RX_8139_BUF_RESERVE);
	/* Init TX descriptors. */
	rl_list_tx_init(sc);
	/* Init Rx memory block. */
	rl_list_rx_init(sc);

	/*
	 * Enable transmit and receive.
	 */
	CSR_WRITE_1(sc, RL_COMMAND, RL_CMD_TX_ENB|RL_CMD_RX_ENB);

	/*
	 * Set the initial TX and RX configuration.
	 */
	CSR_WRITE_4(sc, RL_TXCFG, RL_TXCFG_CONFIG);
	CSR_WRITE_4(sc, RL_RXCFG, RL_RXCFG_CONFIG);

	/* Set the individual bit to receive frames for this host only. */
	rxcfg = CSR_READ_4(sc, RL_RXCFG);
	rxcfg |= RL_RXCFG_RX_INDIV;

	/* If we want promiscuous mode, set the allframes bit. */
	if (ifp->if_flags & IFF_PROMISC) {
		rxcfg |= RL_RXCFG_RX_ALLPHYS;
		CSR_WRITE_4(sc, RL_RXCFG, rxcfg);
	} else {
		rxcfg &= ~RL_RXCFG_RX_ALLPHYS;
		CSR_WRITE_4(sc, RL_RXCFG, rxcfg);
	}

	/* Set capture broadcast bit to capture broadcast frames. */
	if (ifp->if_flags & IFF_BROADCAST) {
		rxcfg |= RL_RXCFG_RX_BROAD;
		CSR_WRITE_4(sc, RL_RXCFG, rxcfg);
	} else {
		rxcfg &= ~RL_RXCFG_RX_BROAD;
		CSR_WRITE_4(sc, RL_RXCFG, rxcfg);
	}

	/* Program the multicast filter, if necessary. */
	rl_setmulti(sc);

#ifdef DEVICE_POLLING
	/* Disable interrupts if we are polling. */
	if (ifp->if_capenable & IFCAP_POLLING)
		CSR_WRITE_2(sc, RL_IMR, 0);
	else
#endif
	/* Enable interrupts. */
	CSR_WRITE_2(sc, RL_IMR, RL_INTRS);

	/* Set initial TX threshold */
	sc->rl_txthresh = RL_TX_THRESH_INIT;

	/* Start RX/TX process. */
	CSR_WRITE_4(sc, RL_MISSEDPKT, 0);

	/* Enable receiver and transmitter. */
	CSR_WRITE_1(sc, RL_COMMAND, RL_CMD_TX_ENB|RL_CMD_RX_ENB);

	mii_mediachg(mii);

	CSR_WRITE_1(sc, RL_CFG1, RL_CFG1_DRVLOAD|RL_CFG1_FULLDUPLEX);

	ifp->if_drv_flags |= IFF_DRV_RUNNING;
	ifp->if_drv_flags &= ~IFF_DRV_OACTIVE;

	callout_reset(&sc->rl_stat_callout, hz, rl_tick, sc);
}

/*
 * Set media options.
 */
static int
rl_ifmedia_upd(struct ifnet *ifp)
{
	struct rl_softc		*sc = ifp->if_softc;
	struct mii_data		*mii;

	mii = device_get_softc(sc->rl_miibus);

	RL_LOCK(sc);
	mii_mediachg(mii);
	RL_UNLOCK(sc);

	return (0);
}

/*
 * Report current media status.
 */
static void
rl_ifmedia_sts(struct ifnet *ifp, struct ifmediareq *ifmr)
{
	struct rl_softc		*sc = ifp->if_softc;
	struct mii_data		*mii;

	mii = device_get_softc(sc->rl_miibus);

	RL_LOCK(sc);
	mii_pollstat(mii);
	RL_UNLOCK(sc);
	ifmr->ifm_active = mii->mii_media_active;
	ifmr->ifm_status = mii->mii_media_status;
}

static int
rl_ioctl(struct ifnet *ifp, u_long command, caddr_t data)
{
	struct ifreq		*ifr = (struct ifreq *)data;
	struct mii_data		*mii;
	struct rl_softc		*sc = ifp->if_softc;
	int			error = 0;

	switch (command) {
	case SIOCSIFFLAGS:
		RL_LOCK(sc);
		if (ifp->if_flags & IFF_UP) {
			rl_init_locked(sc);
		} else {
			if (ifp->if_drv_flags & IFF_DRV_RUNNING)
				rl_stop(sc);
		}
		RL_UNLOCK(sc);
		error = 0;
		break;
	case SIOCADDMULTI:
	case SIOCDELMULTI:
		RL_LOCK(sc);
		rl_setmulti(sc);
		RL_UNLOCK(sc);
		error = 0;
		break;
	case SIOCGIFMEDIA:
	case SIOCSIFMEDIA:
		mii = device_get_softc(sc->rl_miibus);
		error = ifmedia_ioctl(ifp, ifr, &mii->mii_media, command);
		break;
	case SIOCSIFCAP:
#ifdef DEVICE_POLLING
		if (ifr->ifr_reqcap & IFCAP_POLLING &&
		    !(ifp->if_capenable & IFCAP_POLLING)) {
			error = ether_poll_register(rl_poll, ifp);
			if (error)
				return(error);
			RL_LOCK(sc);
			/* Disable interrupts */
			CSR_WRITE_2(sc, RL_IMR, 0x0000);
			ifp->if_capenable |= IFCAP_POLLING;
			RL_UNLOCK(sc);
			return (error);
			
		}
		if (!(ifr->ifr_reqcap & IFCAP_POLLING) &&
		    ifp->if_capenable & IFCAP_POLLING) {
			error = ether_poll_deregister(ifp);
			/* Enable interrupts. */
			RL_LOCK(sc);
			CSR_WRITE_2(sc, RL_IMR, RL_INTRS);
			ifp->if_capenable &= ~IFCAP_POLLING;
			RL_UNLOCK(sc);
			return (error);
		}
#endif /* DEVICE_POLLING */
		break;
	default:
		error = ether_ioctl(ifp, command, data);
		break;
	}

	return (error);
}

static void
rl_watchdog(struct rl_softc *sc)
{

	RL_LOCK_ASSERT(sc);

	if (sc->rl_watchdog_timer == 0 || --sc->rl_watchdog_timer >0)
		return;

	device_printf(sc->rl_dev, "watchdog timeout\n");
	sc->rl_ifp->if_oerrors++;

	rl_txeof(sc);
	rl_rxeof(sc);
	rl_init_locked(sc);
}

/*
 * Stop the adapter and free any mbufs allocated to the
 * RX and TX lists.
 */
static void
rl_stop(struct rl_softc *sc)
{
	register int		i;
	struct ifnet		*ifp = sc->rl_ifp;

	RL_LOCK_ASSERT(sc);

	sc->rl_watchdog_timer = 0;
	callout_stop(&sc->rl_stat_callout);
	ifp->if_drv_flags &= ~(IFF_DRV_RUNNING | IFF_DRV_OACTIVE);

	CSR_WRITE_1(sc, RL_COMMAND, 0x00);
	CSR_WRITE_2(sc, RL_IMR, 0x0000);

	/*
	 * Free the TX list buffers.
	 */
	for (i = 0; i < RL_TX_LIST_CNT; i++) {
		if (sc->rl_cdata.rl_tx_chain[i] != NULL) {
			if (sc->rl_cdata.rl_tx_chain[i] != NULL) {
				bus_dmamap_sync(sc->rl_cdata.rl_tx_tag,
				    sc->rl_cdata.rl_tx_dmamap[i],
				    BUS_DMASYNC_POSTWRITE);
				bus_dmamap_unload(sc->rl_cdata.rl_tx_tag,
				    sc->rl_cdata.rl_tx_dmamap[i]);
				m_freem(sc->rl_cdata.rl_tx_chain[i]);
				sc->rl_cdata.rl_tx_chain[i] = NULL;
			}
			CSR_WRITE_4(sc, RL_TXADDR0 + (i * sizeof(uint32_t)),
			    0x0000000);
		}
	}
}

/*
 * Device suspend routine.  Stop the interface and save some PCI
 * settings in case the BIOS doesn't restore them properly on
 * resume.
 */
static int
rl_suspend(device_t dev)
{
	struct rl_softc		*sc;

	sc = device_get_softc(dev);

	RL_LOCK(sc);
	rl_stop(sc);
	sc->suspended = 1;
	RL_UNLOCK(sc);

	return (0);
}

/*
 * Device resume routine.  Restore some PCI settings in case the BIOS
 * doesn't, re-enable busmastering, and restart the interface if
 * appropriate.
 */
static int
rl_resume(device_t dev)
{
	struct rl_softc		*sc;
	struct ifnet		*ifp;

	sc = device_get_softc(dev);
	ifp = sc->rl_ifp;

	RL_LOCK(sc);

	/* reinitialize interface if necessary */
	if (ifp->if_flags & IFF_UP)
		rl_init_locked(sc);

	sc->suspended = 0;

	RL_UNLOCK(sc);

	return (0);
}

/*
 * Stop all chip I/O so that the kernel's probe routines don't
 * get confused by errant DMAs when rebooting.
 */
static int
rl_shutdown(device_t dev)
{
	struct rl_softc		*sc;

	sc = device_get_softc(dev);

	RL_LOCK(sc);
	rl_stop(sc);
	RL_UNLOCK(sc);

	return (0);
}