The priority goes from "error" to "debug".
Connectors are polled every 10 seconds. Reading EDID is part of this
polling. However, when an invalid EDID is returned, this error message
is logged. When using Newcons for instance, having a kernel message
every 10 seconds is getting annoying.
Now that it's a debug message, it'll be logged only if hw.dri.debug is
enabled. This fix console spamming for some users.
Tested by: Larry Rosenman <ler@lerctr.org>
clients. Mask RX interrupts while grabbed on the atmel serial
driver. This UART interrupts every character. When interrupts are
enabled at the mountroot> prompt, this means the ISR eats the
characters. Rather than try to create a cooperative buffering system
for the low level kernel console, instead just mask out the ISR. For
NS8250 and decsendents this isn't needed, since interrupts only happen
after 14 or more characters (depending on the fifo settings). Plumb
such that these are optional so there's no change in behavior for all
the other UART clients. ddb worked on this platform because all
interrupts were disabled while it was running, so this problem wasn't
noticed. The mountroot> issue has been around for a very very long
time.
MFC after: 3 days
... for msleep/cv_*wait() return values, where wait_event*() is used
on Linux. ERESTARTSYS is the return code expected by callers when the
operation was interrupted.
For instance, this is the case of radeon_cs_ioctl() (radeon_cs.c): if
an error occurs, and the code isn't ERESTARTSYS (eg. EINTR), it logs an
error.
Note that ERESTARTSYS is defined as ERESTART, but this keeps callers'
code close to Linux.
Submitted by: avg@ (previous version)
to the soreceive(). This exposed a bug. When reading from a raw socket,
when our fake limit is depleted, we receive a truncated mbuf chain, with
m->m_pkthdr.len > m_length(m). The first problem is that MSG_TRUNC was not
handled. The second one is that we didn't reinit uio_resid in our endless
loop (neither flags), and if socket buffer contained several records, then
we quickly deplete our fake limit. The third bug, actually introduced in
r248885, is that MJUMPAGESIZE isn't enough to handle maximum packet that
ng_ksocket(4) can theoretically receive.
Changes:
- Reinit uio_resid and flags before every call to soreceive().
- Set maximum acceptable size of packet to IP_MAXPACKET. As for now the
module doesn't support INET6.
- Properly handle MSG_TRUNC return from soreceive().
PR: 184601
Submitted & tested by: Viktor Velichkin <avisom yandex.ru>
Sponsored by: Nginx, Inc.
Normal and bold fonts each have a glyph map for single or left half-
glyphs, and right half glyphs. The flag TF_CJK_RIGHT in term_char_t
requests the right half-glyph.
Reviewed by: ed@
Sponsored by: The FreeBSD Foundation
The previous code was checking the "VGA Enable" bit on the video card's
parent PCI-to-PCI bridge only. This didn't work for the case where the
video card is attached to the root PCI bus (ie. the card has no parent
PCI-to-PCI bridge).
Now, the new code:
1. checks the "VGA Enable" bit on the parent bridge only if it's a
PCI-to-PCI bridge;
2. always checks the "I/O" and "Memory address space decoding" bits
on the video card itself.
However, vendor-specific bits are not used.
This fixes the use of many integrated Radeon cards: without this patch,
we fail to detect them as the boot display and, when radeonkms looks for
the Video BIOS, it skips the shadow copy made by the System BIOS. It
then fails to fully initialize the card, because the shadow copy is the
only way to read the Video BIOS in these situations. A workaround was to
force the boot display selection using the "hw.pci.default_vgapci_unit"
tunable.
A previous version of this patch added a new function doing the checks.
Now, the vga_pci_is_boot_display() function is used to perform the
checks (only until the boot display is found) and return if the given
device is the boot display or not.
Furthermore, vga_pci_attach() logs "Boot video device" if the card being
attached it the Chosen One:
vgapci0: <VGA-compatible display> [...]
vgapci0: Boot video device
Reviewed by: kib@, jhb@ (both a previous version)
Tested by: lunatic_ (#freebsd-xorg, integrated Radeon card,
xmj (#freebsd-xorg, i915+NVIDIA cards)
This, and several subsequent commits, are suspend/resume for various PowerMac
drivers, which will include a change to the global suspend/resume code
eventually.
Introduce a new formatting bit (TF_CJK_RIGHT) that is set when putting a
cell that is the right part of a CJK fullwidth character. This will
allow drivers like vt(9) to support fullwidth characters properly.
emaste@ has a patch to extend vt(9)'s font handling to increase the
number of Unicode -> glyph maps from 2 ({normal,bold)} to 4
({normal,bold} x {left,right}). This will need to use this formatting
bit to determine whether to draw the left or right glyph.
Reviewed by: emaste
Do not insert active ports into pool->sp_active list if they are success-
fully assigned to some thread. This makes that list include only ports that
really require attention, and so traversal can be reduced to simple taking
the first one.
Remove idle thread from pool->sp_idlethreads list when assigning some
work (port of requests) to it. That again makes possible to replace list
traversals with simple taking the first element.
With this, also shut shut off the display (DPMS-style) and disable the clocking
when the backlight level is set to 0. This is taken from the radeonkms driver
(radeon_legacy_encoders.c) which doesn't yet support PowerPC, and won't for a
while, as it's missing full AGP support.
using cpuid can be quirky (this is the case of VMWare without the
vPMC support) but fail to probe hwpmc.
o Apply the fix for XEON family of processors as established by
315338-020 document (bug AJ85).
Sponsored by: EMC / Isilon storage division
Reviewed by: fabient
eneough queue space before queuing a bunch of IP fragments.
As the comment in the committed change says, in the post-if_transmit(),
post-SMP, post-preemption world, there's just too much overlapping
concurrent code paths and different approaches to driver transmit
queue management to have this code even remotely be effective.
The only specific place it could be useful is if ALTQ is enabled
but again it doesn't at all promise that all the fragments will be
transmitted anyway.
The main reason for committing this change is to disable a parallel
place where the drops counter is incremented. This is a side effect
of an upcoming change to ixgbe/cxgbe to handle the queue drops
counter slightly better.
Sponsored by: Netflix, Inc.
The least significant 8 bits of 'pm_flags' are now used for the IPI vector
to use for nested page table TLB shootdown.
Previously we used IPI_AST to interrupt the host cpu which is functionally
correct but could lead to misleading interrupt counts for AST handler. The
AST handler was also doing a lot more than what is required for the nested
page table TLB shootdown (EOI and IRET).
Qualcomm Snapdragon S4 and Snapdragon 400/600/800 SoCs and has architectural
similarities to ARM Cortex-A15. As for development boards IFC6400 series embedded
boards from Inforce Computing uses Snapdragon S4 Pro/APQ8064.
Approved by: stas (mentor)
When processing receive buffer, write the amount of data, expected
in present request record, into socket's so_rcv.sb_lowat to make stack
aware about our needs. When processing following upcalls, ignore them
until socket collect enough data to be read and processed in one turn.
This change reduces number of context switches and other operations
in RPC stack during large NFS writes (especially via non-Jumbo networks)
by order of magnitude.
After precessing current packet, take another look into the pending
buffer to find out whether the next packet had been already received.
If not, deactivate this port right there without making RPC code to
push this port to another thread just to find that there is nothing.
If the next packet is received partially, also deactivate the port, but
also update socket's so_rcv.sb_lowat to not be woken up prematurely.
This change additionally reduces number of context switches per NFS
request about in half.
Previously the code would just iterate over the whole tree as if it were
just a list.
Without this change I would observe X server becoming more and more
jerky over time.
MFC after: 5 days
covered by sbintime (LONG_MAX seconds).
Some programs use timeout values in excess of 1000 years. The conversion
to sbintime caused wrap-around on overflow, which resulted in short or
negative timeout values. This caused long delays on sockets opened by
affected programs (e.g. OpenSSH).
Kernels compiled without -fno-strict-overflow were not affected, apparently
because the compiler tested the sign of the timeout value before performing
the multiplication that lead to overflow.
When the -fno-strict-overflow option was added to CFLAGS, this optimization
was disabled and the test was performed on the result of the multiplication.
Negative products were caught and resulted in EINVAL being returned, but
wrap-around to positive values just shortened the timeout value to the
residue of the result that could be represented by sbintime.
The fix is to cap the timeout values at the maximum that can be represented
by sbintime, which is 2^31 - 1 seconds or more than 68 years.
After this change, the kernel can be compiled with -fno-strict-overflow
with no ill effects.
MFC after: 3 days
linker_unload_file() rather than kern_kldload() and kern_kldunload(). This
ensures that the handlers are invoked for files that are loaded/unloaded
automatically as dependencies. Previously, they were only invoked for files
loaded by a user.
As a side effect, the kld_load and kld_unload handlers are now invoked with
the kernel linker lock exclusively held.
Reported by: avg
Reviewed by: jhb
MFC after: 2 weeks
re-links dynamic states to default rule instead of
flushing on rule deletion.
This can be useful while performing ruleset reload
(think about `atomic` reload via changing sets).
Currently it is turned off by default.
MFC after: 2 weeks
Sponsored by: Yandex LLC
to fail and return error.
- Use make_dev_p() in tty_makedevf() instead of make_dev_cred().
- Always pass MAKEDEV_CHECKNAME flag.
- Optionally pass MAKEDEV_REF flag.
- Provide macro for compatibility with old API.
This fixes races with simultaneous creation and desctruction of
ttys, and makes it possible to call tty_makedevf() from device
cloners.
A race in tty_watermarks() still exist, since the latter drops
lock for M_WAITOK allocation. This will be addressed in separate
commit.
Reviewed by: kib
Sponsored by: Nginx, Inc.
child process that were inherited from its parent. However, this should
not be done in the case of a vfork, since the fork handler ends up removing
the tracepoints from the shared vm space, and userland DTrace probes in the
parent will no longer fire as a result.
Now the child of a vfork may trigger userland DTrace probes enabled in its
parent, so modify the fasttrap probe handler to handle this case and handle
the child process in the same way that it would handle the traced process.
In particular, if once traces function foo() in a process that vforks, and
the child calls foo(), fasttrap will treat this call as having come from the
parent. This is the behaviour of the upstream code.
While here, add #ifdef guards to some code that isn't present upstream.
MFC after: 1 month
in6addr_any and is not in the CLIP table either. This fixes a reported
TOE+IPv6 NULL-dereference panic in do_pass_open_rpl().
While here, stop creating hardware servers for any loopback address.
It's just a waste of server tids.
MFC after: 1 week
advisory lock cannot be obtained, prevent double-close of the vnode in
vn_close() called from the fdrop(), by resetting file' f_ops methods.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Besides not making sense, open(O_EXEC) for fifo creates fifoinfo with
zero readers and writers counts, which causes premature free of pipes.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
callers treat the MSI 'addr' and 'data' fields as opaque and also lets
bhyve implement multiple destination modes: physical, flat and clustered.
Submitted by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
Reviewed by: grehan@
This allows it to be better tracked as well as being able to leverage
UMA for more interesting/useful behaviour at a later date.
Sponsored by: Netflix, Inc.
Some Intel XHCI controlles timeout processing so-called "TRBs" when
the final LINK TRB of a so-called "TD" has the CHAIN-BIT set.
MFC after: 1 week
Tested by: glebius @
the TTY. In such a case, ttydev_close() is called multiple times and
each time, t_revokecnt is incremented and cv_broadcast() is called for
both the t_outwait and t_inwait condition variables.
Let's say revoke(2) comes in first and gets to call tty_drain() from
ttydev_leave(). Let's say that the revoke comes from init(8) as the
result of running "shutdown -r now". Since shutdown prints various
messages to the console before announing that the machine will reboot
immediately, let's also say that the output queue is not empty and
that tty_drain() has something to do. Let's assume this all happens
on a 9600 baud serial console, so it takes a time to drain.
The shutdown command will exit(2) and as such will end up closing
stdout. Let's say this close will come in second, bump t_revokecnt
and call tty_wakeup(). This has tty_wait() return prematurely and
the next thing that will happen is that the thread doing revoke(2)
will flush the TTY. Since the drain wasn't complete, the flush will
effectively drop whatever is left in t_outq.
This change takes into account that tty_drain() will return ERESTART
due to the fact that t_revokecnt was bumped and in that case simply
call tty_drain() again. The thread in question is already performing
the close so it can safely finish draining the TTY before destroying
the TTY structure.
Now all messages from shutdown will be printed on the serial console.
Obtained from: Juniper Networks, Inc.
containing the trap instruction encoding (0x7c810808), and restoring it back
with the frame on return. This caused it to panic on my ppc32 machine, but
somehow my ppc64 machine overlooked it, because I was using such a simple
dtrace probe.
X-MFC-with: r259245
MFC after: 2 weeks
We need to do this because the Linux compat layer uses sx(9) for
mutex, however the lagg code uses rmlocks and calls into the mellanox
driver. This causes deadlock due to sleeping while holding a rmlock.
Submitted by: Shahar Klein (shahark mellanox.com)
MFC After: 3 days.
support all valid SAM-5 LUN IDs. CAM_VERSION is bumped, as the CAM ABI
(though not API) is changed. No behavior is changed relative to r257345
except that LUNs with non-zero high 32 bits will no longer be ignored
during device enumeration for SIMs that have set PIM_EXTLUNS.
Reviewed by: scottl
o Assign sc->an_dev in an_probe() (which isn't really a probe function in
the standard newbus sense) as we may need it for printing errors.
o Use device_printf() rather than if_printf() in an_reset() - this is
called from an_probe() long before the ifp structure is initialised
in an_attach().
o Initialize the ifp structure early in an_attach() as we use if_printf()
in cases where allocation of descriptors etc fails.
MFC after: 3 days
them up as part of firmware initialization (which the driver gets to do
only if it's the master driver).
Read the range of tids available for the ETHOFLD functionality if it's
enabled.
New is_ftid() and is_etid() functions to test whether a tid falls within
the range of filter tids or ETHOFLD tids respectively.
MFC after: 2 weeks
Historically creation of device aliases created symbolic links using only
name of target device as a link target, not considering current directory.
Fix that by adding number of "../" chunks to the terget device name,
required to get out of the current directory to devfs root first.
MFC after: 1 month
receiving Zero Length Packets, ZLPs. See comment in code for more
information.
MFC after: 1 week
Reported by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
When a da or ada device dissappears, outstanding IOs fail with
ENXIO, not EIO. The check for EIO was probably copied from Illumos,
where that is indeed the correct errno.
Without this change, pulling a busy drive from a zpool would usually
turn it into UNAVAIL, even though pulling an idle drive would turn
it into REMOVED. With this change, it is REMOVED every time.
Also, vdev_geom_io_intr shouldn't do zfs_post_remove, because that
results in devd getting two resource.fs.zfs.removed events. The
comment said that the event had to be sent directly instead of
through the async removal thread because "the DE engine is using
this information to discard prevoius I/O errors". However, the fact
that vdev_geom_io_intr was never actually sending the events until
now, and that vdev_geom_orphan never sent them at all, and that
vdev_geom_orphan usually gets called about 2 seconds after the
actual removal, means that FreeBSD's userland can cope with a late
event just fine.
Approved by: ken (mentor)
Sponsored by: Spectra Logic Corporation
MFC after: 4 weeks
In case of 4K allocation quantum that means for allocations up to 128K.
With growth of memory fragmentation these lists may grow to quite a large
sizes (tenths and hundreds of thousands items). Having in one list items
of different sizes in worst case may require full linear list traversal,
that may be very expensive. Having lists for items of single size means
that unless user specify some alignment or border requirements (that are
very rare cases) first item found on the list should satisfy the request.
While running SPEC NFS benchmark on top of ZFS on 24-core machine with
84GB RAM this change reduces CPU time spent in vmem_xalloc() from 8%
and lock congestion spinning around it from 20% to invisible levels.
And that all is by the cost of just 26 more pointers per vmem instance.
If at some point our kernel will start to actively use KVA allocations
with odd sizes above 128K, something may need to be done to bigger lists
also.
all the structures. While here, move a helper struct only used in
the kernel parser out of this header since it is not part of the MP
specification itself.
completely full, we'd not complete any of the mbufs due to the fence
post error (this creates a large leak). When this is fixed, we still
leak, but at a much smaller rate due to a race between ateintr and
atestart_locked as well as an asymmetry where atestart_locked is
called from elsewhere. Ensure that we free in-flight packets that
have completed there as well. Also remove needless check for NULL on
mb, checked earlier in the loop and simplify a redundant if.
MFC after: 3 days
When the guest is bringing up the APs in the x2APIC mode a write to the
ICR register will now trigger a return to userspace with an exitcode of
VM_EXITCODE_SPINUP_AP. This gets SMP guests working again with x2APIC.
Change the vlapic timer lock to be a spinlock because the vlapic can be
accessed from within a critical section (vm run loop) when guest is using
x2apic mode.
Reviewed by: grehan@
sys/cdefs.h. In particular, in case of COMPAT_43, param.h includes
sys/types.h, which includes sys/select.h, which includes
sys/_sigset.h. The _sigset.h customizes the provided definions based
on COMPAT_43, eliminating osigset_t if symbol is not defined. The
sys/proc.h is included after opt_compat.h and needs osigset_t.
Move opt_compat.h inclusion into the right place.
Sponsored by: The FreeBSD Foundation
the excess code in g_io_check(), bio_resid is also truncated by
g_io_deliver(). As result, bufdonebio() assigns truncated value to
the buffer b_resid field.
Use the residual bio_completed to calculate buffer b_resid from
b_bcount in bufdonebio(), instead of bio_resid, calculated from
bio_length in g_io_deliver().
The issue is seemingly caused by the code rearrange into g_io_check(),
which is not present in stable/10. The change still looks as the
useful change to have in 10 nevertheless.
Reported by: Stefan Hegnauer <stefan.hegnauer@gmx.ch>
Tested by: pho, Stefan Hegnauer <stefan.hegnauer@gmx.ch>
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
the bio is unmapped, so we must map the bio pages into pbuf. This
works around the geom classes which do not follow the MAXPHYS limit on
the i/o size, since such classes do not know about unmapped bios
either.
Reported by: Paolo Pinto <paolo.pinto@netasq.com>
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Intel manual says: "If a transition is already in progress, transition to
a new value will subsequently take effect. Reads of IA32_PERF_CTL determine
the last targeted operating point." So seems it should be fine to just
trigger wanted transition and go. Linux does the same.
MFC after: 1 month
(64MB). Even if we would find one somehow, ZFS kernel code rejects such
devices. It is funny to look on attempts to read 4 256K vdev labels from
1.44MB floppy, though it is not very practical and quite slow.
inclusion of right after sys/param.h.
o Only vt_core module use compat options, move it from common header to module.
Reported by: Larry Rosenman ler at lerctr dot org
Sponsored by: The FreeBSD Foundation
this change we may end up with a panic (Fatal kernel mode data abort:
'External Non-Linefetch Abort (S)') as described in
http://e2e.ti.com/support/arm/sitara_arm/f/791/t/276862.aspx.
It is now possible to bring up I2C1 and I2C2 on BBB.
Approved by: adrian (mentor)
o Include opt_splash.h for vt(9) to know when splash device is enabled.
o Build logo_freebsd.c only if splash and vt are enabled.
o Include opt_compat.h to know when we have to respect compatibility.
Sponsored by: The FreeBSD Foundation
(like NAA assigned) and identify the same entity (like device or port).
Otherwise there can be false positives since at least some models of
Seagate disks use same IDs for the whole device and one of its ports.
MFC after: 2 weeks
The code was unmodified compared to Linux and returned the amount of
received bytes from the i2c bus. This led to non-working i2c bus and
failure to eg. read monitor's EDID, if connected to DisplayPort.
MFC after: 3 days
Tested by: Mikaël Urankar <mikael.urankar@gmail.com>
This fixes radeon_agp_init() and gtt_size is now correct. However, this
is not enough to make Radeon AGP cards work: ttm_agp_backend.c isn't
implemented yet.
Submitted by: tijl@
going on in here than can be fixed, and I introduced some of my own. Rather
than fix the whole host of them, back out my bugs.
Found by: bde
X-MFC with: r259080
This decouples the guest's 'hz' from the host's 'hz' setting. For e.g. it is
now possible to have a guest run at 'hz=1000' while the host is at 'hz=100'.
Discussed with: grehan@
Tested by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
synchronous (with FILE_SYNC) writes because non-contiguous
byte ranges in the same buffer cache block are being
written. This patch adds a new mount option "noncontigwr"
which allows the non-contiguous byte ranges to be combined,
with the dirty byte range becoming the superset of the bytes
that are dirty, if the file has not been file locked.
This reduces the number of writes significantly for software
builds. The only case where this change might break existing
applications is where an application is writing
non-overlapping byte ranges within the same buffer cache block
of a file from multiple clients concurrently.
Since such an application would normally do file locking on
the file, avoiding the byte range merge for files that have
been file locked should be sufficient for most (maybe all?) cases.
Submitted by: jhb (earlier version)
Reviewed by: kib
MFC after: 3 weeks
vcpu and destroy its thread context. Also modify the 'HLT' processing to ignore
pending interrupts in the IRR if interrupts have been disabled by the guest.
The interrupt cannot be injected into the guest in any case so resuming it
is futile.
With this change "halt" from a Linux guest works correctly.
Reviewed by: grehan@
Tested by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
Make the scan state optional - we'll obviously need a vap, but we now
won't require the scan state. the only thing the scan state is needed
for is to check for the list of SSIDs to scan - which we can now
just plain ignore by passing in NULL as the scan state pointer.
Tested:
* Intel 5100 (STA)
This is in preparation for being able to use iwn_scan() to do an off
channel scan to reset the RF tuning.
It should be a no-op.
Tested:
* Intel 5100 (STA)
in preparation for the scan based retune logic.
The linux iwlwifi driver does a rescan (onto a non-active channel)
to force an RF retune when the PLCP error rates exceed a certain threshold.
* Add code to track HT PLCP rate errors;
* Separate out the PLCP error count fetch and update so the delta
can be used when checking for PLCP error rates;
* Implement the PLCP error logic from iwlwifi;
* For now, just print out whenever the error rate exceeds the
threshold.
The actual scan based retune will take a bit more effort; the scan
command code right now assumes that a scan state is passed in.
This does need to change to be more flexible (both for this and
in preparation for scanning multiple channels at once.)
Tested:
* 5100 (STA mode)
* 2200 (STA mode)
* 2230 (STA mode)
working on some RF tuning issues.
The linux iwlwifi driver has these thresholds which they use to see
if there are PLCP errors over a certain interval. If they hit this,
they trigger a single-channel (different from active channels!)
scan to retune the RF front-end.
for signed values due to a compiler authors considering integer
overflow as impossible.
The change follows suit of other projects taking the same measure.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
vm_max_virtual_address to be KERNVIRTADDR + 256MB. This allows some
future shock protection since the KVA requirements have gone up since
the unmapped changes have gone in, as well as preventing us from
overlapping with the hardware devices, which we map at 0xd0000000,
which we'd hit with anything more than 85MB...
MFC after: 3 days
always returning '0' for all the reads, even for the outputs. It is now
known to work with gpioiic(4) and gpioled(4).
Approved by: adrian (mentor)
Tested on: BBB
regions which represent the total amount of memory. The size of these regions
is not the physical size of the chip but it is a logical one and it is given
by the OpenFirmware, it is selectable at boot time and varies between 16MB and
256MB in my case. There is an 'automatic' option which would select the size as
64MB in case you have around 16GB of RAM.
To make sure we can allocate RAM with the automatic option bump this value
of PHYS_AVAIL_SZ to 256.
- Add 'hyperv' module into build;
- Allow building Hyper-V support as part of the kernel;
- Hook Hyper-V build into NOTES.
This is intended for MFC if re@ permits.
MFC after: 3 days
- Add support to 40Gbps devices;
- Add support to control adaptive interrupt coalescing (AIC)
via sysctl;
- Improve support of BE3 devices;
Many thanks to Emulex for their continued support of FreeBSD.
Submitted by: Venkata Duvvuru <VenkatKumar.Duvvuru Emulex Com>
MFC after: 3 days
According to online documentation [1], Ext4 has two new "special"
inodes so add the new exclude and replica inodes.
Reference:
[1] https://ext4.wiki.kernel.org/index.php/Ext4_Disk_Layout
Reported by: Mike Ma
MFC after: 3 weeks
defaults to PANIC_REBOOT_WAIT_TIME (a long-existing kernel config
setting). Use this now-variable value in place of the defined constant
to control how long the system waits after a panic before rebooting.
scheduling classes in the chip and to bind tx queue(s) to a scheduling
class respectively. These can be used for various kinds of tx traffic
throttling (to force selected tx queues to drain at a fixed Kbps rate,
or a % of the port's total bandwidth, or at a fixed pps rate, etc.).
Obtained from: Chelsio
by SCHED_PRI_TICKS should be SCHED_PRI_RANGE - 1 so that the resulting
priority value (before nice adjustment) is between SCHED_PRI_MIN and
SCHED_PRI_MAX, inclusive.
Submitted by: kib
Reported by: pho
MFC after: 1 week
has outgrown its original name. Originally this function simply sent an IPI
to the host cpu that a vcpu was executing on but now it does a lot more than
just that.
Reviewed by: grehan@
This is to support LOCK_LOG_* functionality effectively in debugging
environments but it is overkill because really LOCK_DEBUG should be on
only if (KTR_COMPILE & KTR_LOCK) is true.
Fix this by applying the correct logic.
In this process, move the KTR classes to its own header to reduce
namespace pollution.
Sponsored by: EMC / Isilon storage division
Reviewed by: jhb
for these chipsets.
* Correctly set the active/passive flag in the scan request - this is
NOT a "is the channel active|passive"; it's to do with whether we
have an SSID to actively scan for or not. The firmware takes care
of the active/passive setup of the channel.
* Calculate the active/passive dwell time based on the beacon interval
and the channel mode, rather than using a hard coded value.
* For now, hardcode the scan service_time. It's defined as:
31:22 - number of beacon intervals to come back onto the home channel
for;
0:21 - time (microseconds) to come back onto the home channel for.
When doing an active scan when the NIC is active (whether we're associated
or not - it only matters if we've setup the NIC to a destination or not)
this determines how much time to stay on the home channel for when
scanning. We can tune this based on the amount of active traffic.
For now it's 4 beacon intervals and 100 microseconds.
* Fix the "good crc threshold" setting. It differs based on the NIC
firmware. Some older firmware required a workaround; the later
firmware instead treats the field as a flag.
* Enforce that we are not sending a scan command if one is already
pending. Any time this is done is a bug and it absolutely needs
to be fixed - so be very loud.
* Add the SCAN flag to a few debug messages that are scan related but
only occuring under STATE.
Now, this does get noisy when you're scanning in an actively busy 2GHz
network as the firmware (for reason I don't quite yet understand) seems
hell bent on staying on some passive channels longer than it should.
However, it should eventually recover and complete the scan.
This is a work in progress; please let me know if things get stuck or
if things improve!
Tested:
* intel centrino 2200
* intel centrino 2230
* intel 6200
* intel 5100
* intel 4965 (gets upset, but that's a known issue)
Obtained from: linux iwlwifi
TX ring according to what the firmware requires.
The firmware requires A-MPDU sub-frames to be at a very specific ring
offset - that is, the ring slot offset should be (seqno % 256.)
This holds for every NIC I've tested thus far except the 4965,
which starts erroring out here shortly before the firmware panics.
Which is good, it's doing what it's supposed to (read: capture that
we've screwed up somewhere.)
The specifics about getting this stuff right:
* the initial seqno allocation should match up with the ringid.
* .. yes, this means we can start at a ring offset that isn't zero.
* .. because we program the start seqno in the firmware message
to setup the AC.
* The initial seqno allocation may be non-zero _and_ frames may be
being transmitted during a-mpdu negotiation. I faced similar
issues on ath(4) and had to software queue frames to that node+TID
during A-MPDU negotiation.
* seqno allocation should be in lockstep with ring increments.
* If we fail to transmit some segment, no, we shouldn't reuse that
ring slot. We should just transmit a BAR (which we aren't yet
doing, sigh) and move onto the next seqno.
* In theory there shouldn't be any holes in the seqno space when
we are transmitting frames.
Tested:
* 4965 (throws problems, so yes we have to fix this);
* 5100 (seems ok);
* 6200 (seems ok);
* 2200 (seems ok);
* 2230 (seems ok).
The directory sys/dev/drm2/i915 is apperently contributed code.
Revert to the broken version of this file to make future imports easier.
Requested by: kib
- The remote host sends a FIN
- in an ACK for a sequence number for which an ACK has already
been received
- There is still unacked data on route to the remote host
- The packet does not contain a window update
The packet may be dropped without processing the FIN flag.
PR: kern/99188
Submitted by: Staffan Ulfberg <staffan@ulfberg.se>
Discussed with: andre
MFC after: never
MACHINE_ARCH values whose binaries this kernel can run. This patch provides
a feature requested for implementing pkgng ABI identifiers in a robust
way.
The list is designed to indicate whether, say, an i386 package can be run on
the current system. If kern.supported_abis contains "i386", then the answer
is yes. Otherwise, the answer is no.
At the moment, this only supports MACHINE_ARCH and MACHINE_ARCH32. As we
gain support for more interesting combinations, this needs to become more
flexible, possibily through the sysent framework, along with the
hw.machine_arch emulation immediately preceding this code in kern_mib.c.
Reviewed by: imp
MFC after: 3 days
Open Firmware-centric:
- Keep the static list of regions in platform.c instead of ofw_machdep.c
- Move various merging and sorting operations to platform.c as well
- Move apple_hacks code out of ofw_machdep.c and into platform_powermac.c,
where it belongs
- Move CHRP-specific dynamic-reconfiguration memory parsing into
platform_chrp.c instead of pretending it is shared code
in /chosen, be ihandles. The ePAPR spec makes those cross-reference phandles,
since FDT has no concept of ihandles. Have the OF FDT CI module interpret
queries about ihandles as cross-reference phandles.
We had previously tried to flush all MKDIR_PARENT dependencies (and
all the NEWBLOCK pagedeps) by calling ffs_update(). However this will
only resolve these dependencies in direct blocks. So very large
directories with MKDIR_PARENT dependencies in indirect blocks had
not yet gotten flushed. As the directory is in the midst of doing a
complete sync, we simply defer the checking of the MKDIR_PARENT
dependencies until the indirect blocks have been sync'ed.
Reported by: Shawn Wallbridge of imaginaryforces.com
Tested by: John-Mark Gurney <jmg@funkthat.com>
PR: 183424
MFC after: 2 weeks
for extending and reusing it.
The sendfile_sync wrapper is mostly just a "mbuf transaction" wrapper,
used to indicate that the backing store for a group of mbufs has completed.
It's only being used by sendfile for now and it's only implementing a
sleep/wakeup rendezvous. However, there are other potential signaling
paths (kqueue) and other potential uses (socket zero-copy write) where the
same mechanism would also be useful.
So, with that in mind:
* extract the sendfile_sync code out into sf_sync_*() methods
* teach the sf_sync_alloc method about the current config flag -
it will eventually know about kqueue.
* move the sendfile_sync code out of do_sendfile() - the only thing
it now knows about is the sfs pointer. The guts of the sync
rendezvous (setup, rendezvous/wait, free) is now done in the
syscall wrapper.
* .. and teach the 32-bit compat sendfile call the same.
This should be a no-op. It's primarily preparation work for teaching
the sendfile_sync about kqueue notification.
Tested:
* Peter Holm's sendfile stress / regression scripts
Sponsored by: Netflix, Inc.
shifts into the sign bit. Instead use (1U << 31) which gets the
expected result.
This fix is not ideal as it assumes a 32 bit int, but does fix the issue
for most cases.
A similar change was made in OpenBSD.
Discussed with: -arch, rdivacky
Reviewed by: cperciva
requires process descriptors to work and having PROCDESC in GENERIC
seems not enough, especially that we hope to have more and more consumers
in the base.
MFC after: 3 days
http://svnweb.freebsd.org/changeset/base/258221
I introduced a bug which initialized global locks
whenever the SCTP stack initialized. This was fixed in
http://svnweb.freebsd.org/changeset/base/258574
by rodrigc@. He just initialized the locks for
the default vnet. This fix reverts to the old
behaviour before r258221, which explicitly makes
sure it is only called once, because this works also on
other platforms.
MFC after: 3 days
X-MFC with: r258574.
decides to do nothing.
If this isn't done, then a scan request whilst a scan occurs in an active
channel set or a completed channel set will hang.
Tested:
* Intel 5100, STA mode
