- Add quirk for ATI SB600 and SB700 to free SMB controller
- Correct schedule sleep time to 10us on the VIA ehci controller
Reported by: Dorian B<FC>ttner, Andriy Gapon
Submitted by: Hans Petter Selasky
- clean up USB detach logic. There seems to be some problems detaching multiple
USB HUBs connected in series from the root.
- after this patch the rule is:
1) Always use device_detach() on the USB HUB first.
2) Never just device_delete_child() on the USB HUB, because that function
will traverse to all the device leaves and free them first, and then the USB
stack will free the devices twice which doesn't work very well.
- make sure the did DMA delay gets set after the timeout has elapsed to make
logic more clear. There is no functional difference.
Submitted by: Hans Petter Selasky
turn ends our usb process. This means the proc pointer becomes invalid and will
panic if a new kthread is added. Count the number of threads and clear the proc
pointer on the last one.
Suggested by: julian
MFC after: 3 days
being polled.
- Remove the need for Giant from the USB HUB driver.
- Leave device unconfigured instead of disabling the USB port
when Huawei Autoinstall disk detection triggers. This should
fix problems that the Huawei device is not detected after
Autoinstall eject is issued.
- Reported by: Nikolay Antsiferov
- Fix memory use after free race for USB character devices.
- Reported by: Lucius Windschuh
- Factor out the enumeration lock into three functions to make the
coming newbus lock conversion more easy.
- usbd_enum_lock
- usbd_enum_unlock
- usbd_enum_is_locked
Submitted by: hps
enable the ones we want. This has been changed to better
match the ADMtek's reference design to avoid setting the
power-down configuration line of the PHY at the same time
it is reset.
Submitted by: John Hood via hps
direction even if the actual device is opened for read and
write. Fix fflags check so that the UFM and URIO drivers work.
Reported by: Krassimir Slavchev
Submitted by: hps
keys are pressed.
- Reported by: Various people
- add sysctl to disable keyboard led control request
- Reported by: Yoshihiro Ota
- Save system CPU usage: Patch to stop keyboard timer when no
keys are pressed.
Submitted by: hps
MFC after: 3 days
- usb_pc_cpu_invalidate() is called between [consecutive] reads from a device,
so a sequence of BUS_DMASYNC_POSTREAD and _PREREAD should be used. Note we
cannot use or'ed shorthand ( _POSTREAD | _PREREAD) for BUS_DMASYNC flags, as
the low level bus dma sync operation is implementation dependent and we
cannot assume the required order of operations to be guaranteed.
- usb_pc_cpu_flush() is called before writing to a device, so
BUS_DMASYNC_PREWRITE should be used.
Submitted by: Grzegorz Bernacki
Reviewed by: HPS, arm@, usb@ ML
Tested by: HPS, Mike Tancsa
Approved by: re (kib)
Obtained from: Semihalf
cosmetic change to reduce cruft in the proc table.
Also change the idle wait message to `-` like how taskqueues are.
Reviewed by: julian
Approved by: re (kib)
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
USB core:
- add support for defragging of written device data.
- improve handling of alternate settings in device side mode.
- correct return value from usbd_get_no_alts() function.
- reported by: HPS
- P4 ID: 166156, 166168
- report USB device release information to devd and pnpinfo.
- reported by: MIHIRA Sanpei Yoshiro
- P4 ID: 166221
Submitted by: hps
Approved by: re
See PR description for more info. Patch is
implemented differently than suggested, but
having the same result.
PR: usb/137188
Submitted by: hps
Approved by: re
- add support for defragging of written device data.
- improve handling of alternate settings in device side mode.
- correct return value from usbd_get_no_alts() function.
- reported by: HPS
- P4 ID: 166156, 166168
- report USB device release information to devd and pnpinfo.
- reported by: MIHIRA Sanpei Yoshiro
- P4 ID: 166221
Submitted by: hps
Approved by: re
- Add minimum polling support to drive UMASS
and UKBD in case of panic.
- Add extra check to ukbd probe to fix problem about
mouse devices attaching like keyboards.
- P4 ID: 166148
Submitted by: hps
Approved by: re
- add support for setting the UMS polling rate through -F option
passed to moused.
- requested by Alexander Best
- P4 ID: 166075
PR: usb/125264
Submitted by: hps
Approved by: re
USB CORE: busdma improvement
For single segment allocations the boundary field
of the BUSDMA tag should be zero. Currently all
single segment allocations are less than or equal
to 4096 bytes, so the limit does not kick in. If
any single segment USB allocations would be greater
than 4K, then it would be a problem.
Approved by: re (kensmith)
Obtained from: HPS
Giant was only used here to lock down a bit mask of allocated unit
numbers. Change the code to use its own mutex.
Reviewed by: hselasky
Approved by: re (kib)
- Add support for devices that handle set and clear stall in hardware.
- Add missing get timestamp function
- Add more xfer flags
Submitted by: Hans Petter Selasky
Approved by: re (kib)
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
Note that I also added the usbdev to the list, because the 8813 version
is not yet known there. I might have twisted the sorting there but because
8813 comes before 8818, I added it before that (with _8813 to differentiate)
the item.
PR: 135628
Submitted by: Yoshikazu GOTO <goto at on-link dot jp>
Approved by: imp (mentor, implicit)
so that it isn't exposured unless needed. In particular this means
that it's easier to tune the memory layout based on board details.
While here, remove inclusion of <machine/intr.h> from mvreg.h. This
also contains exposure to SoC specifics in MI drivers, because NIRQ
depends on the SoC.
ICIDU NI-707503 which is donated by Nick Hibma (great thanks!). Though
it has a MAXIM RF (0x8) there's some success reports with using GCT RF
(0x9) codes and it worked well for ICIDU NI-707503 too. So codes for
MAXIM and GCT RFs are integrated.
Before this commit, if I rememeber correctly, MAXIM RF is never tested
that it seems it's a first report working with FreeBSD.
part identified as Sunplus Technology Inc. This
happens to sit in a Rosewill RX81U-ES-25A 2.5" SATA
to USB 2.0 external enclosure.
Reviewed by: Hans Petter Selasky
I don't want people to override the mutex when allocating a TTY. It has
to be there, to keep drivers like syscons happy. So I'm creating a
tty_alloc_mutex() which can be used in those cases. tty_alloc_mutex()
should eventually be removed.
The advantage of this approach, is that we can just remove a function,
without breaking the regular API in the future.
- add key mappings for fn keys
- byte swapping for certain models
- Fix leds for keyboards which require an ID byte for the HID output structures
Submitted by: Hans Petter Selasky
Some hardware easily comes out of sync with regard to whether the current or
the next control transfer should be stalled, if a stall command is always
issued before receiving the SETUP packet. After this patch the stall command
will only be issued when a transfer should actually be stalled.
Submitted by: Hans Petter Selasky
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
bug referencing a destroyed lock within TX callbacks during device
detach.
Submitted by: hps (original version)
Tested by: Lucius Windschuh <lwindschuh at googlemail.com>
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
Change the roothub exec functions to take the usb request and data pointers
directly rather than placing them on the parent bus struct.
Submitted by: Hans Petter Selasky
Fix a bug in the USB power daemon code where connection of multiple HUBs in
series would result in incorrect device suspend.
Reported by: Nicolas xxx@wanadoo.fr
Submitted by: Hans Petter Selasky
Use direct reference to parent high-speed HUB instead of indirect, due to
pointer clearing race at detach of parent USB HUB.
Reported by: kientzle
Submitted by: Hans Petter Selasky
PR: usb/133545
Refactor how we interface with the root HUB. This is achieved by making a
direct call from usb2_do_request to the host controller for root hub requests,
this call will perform the controller specific register read/writes and return
the error code.
This cuts out a lot of code in the host controller files and saves one thread
per USB bus.
Submitted by: Hans Petter Selasky
- add support for more complicated HID descriptors which can have multiple
definitions of the same field.
- remove old modulo patch in ums, which I think is due to bad HID parsing,
which should be fixed now.
Reported by: netchild
Submitted by: Hans Petter Selasky
Some cancelable flags are always true. Substitute these away. These cancelable
flags were mostly useful with the root HUB which is now handled differently.
Submitted by: Hans Petter Selasky
Refactor how we interface with the root HUB. This cuts around 1200 lines of
code totally and saves one thread per USB bus.
Submitted by: Hans Petter Selasky
- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" which select for which mode
the current xfer entry is active. Options are: a) Device mode only b) Host
mode only (default-by-zero) c) Both modes. This change was scripted using
the following sed script: "s/\.mh\././g".
- the standard packet size table in "usb_transfer.c" is now a function, hence
the code for the function uses less memory than the table itself.
Submitted by: Hans Petter Selasky
- bugfixes after the memory usage reduction patch
- Use "udev->pipes_max" instead of USB_EP_MAX
- Use correct "bmRequestType" for getting the config descriptor.
Submitted by: Hans Petter Selasky
- memory usage reduction by only allocating the required USB pipes and USB
interfaces.
- cleanup some USB parsing functions to be more flexible.
Submitted by: Hans Petter Selasky
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
it is right for only a tiny fraction of these devices and this
wild-card entry is too broad.
# I run a kernel without this entry at all without ill effects...
Workaround for buggy USB hardware not handling new SETUP packet before STATUS
stage is complete, this allows xfers to endpoint0 to return a short frame.
Submitted by: Hans Petter Selasky
Reported by: me
Workaround for buggy USB hardware not handling new SETUP packet before STATUS
stage is complete, this allows xfers to endpoint0 to return a short frame.
Submitted by: Hans Petter Selasky
Reported by: me
- Move tunable defines into usb_core.h and dependancy towards usb_defs.h
- Leave hardcoded defines in "usb_defs.h".
- Allow overriding all tunable defines.
- Add more customisable typedefs.
- Correct maximum device number.
Submitted by: Hans Petter Selasky
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
Fix regression issue in the USB file system interface.
- Use cdev_privdata pointer as indicator of correct file handle.
- Remove redundant FIFO opened flags.
Don't send ZLP at close for ulpt and uscanner devices as this causes some
models to stop working. This reverts back to the USB1 behaviour.
Submitted by: Hans Petter Selasky
More HID parsing fixes for usb mice.
- be less strict on the last HID item usage.
- preserve item size and count accross items
- improve default HID usage selection.
Tested by: ache
Submitted by: Hans Petter Selasky
Fix bugs and improve HID parsing.
- fix possible memory leak found
- fix possible NULL pointer access
- fix possible invalid memory read
- parsing improvements
- reset item data position when a new report ID is detected.
Submitted by: Hans Petter Selasky
o add Transaction Translator support (still missing ISOC xfers)
o add EHCI_SCFLG_BIGEMMIO flag to force big-endian byte-select to be
set in USBMODE
o split reset work into new public routine ehci_reset so bus shim drivers
can force big-endian byte-select before ehci_init
o enable TT and big-endian MMIO
o force a reset before ehci_init to get byte-select setup
Also go back to using USB_EHCI_BIG_ENDIAN_DESC at compile time to enable the
byteswapping and reduce diffs to the original commits.
This fixes the new USB stack on the Cambria board.
the devfs clone handler to open the (invisible) devices on the fly.
The /dev entries are layed out as follows,
/dev/usbctl = master device
/dev/usb/0.1.0.5 = usb device, (<bus>.<dev>.<iface>.<endpoint>)
/dev/ugen0.1 -> usb/0.1.0.0 = ugen link to ctrl endpoint
This also removes the custom permissions model from USB. Bump
__FreeBSD_version to 800066.
Submitted by: rink (earlier version)
- We don't need to exit the Giant mutex when sleeping. This is done
automatically. Replace Giant by NULL mutex for all control requests in the
enumeration path.
- Optimise away duplicate alternate interface selection requests in USB Host
mode.
Submitted by: Hans Petter Selasky
Improvements to "usb2_transfer_setup()" and "usb2_transfer_unsetup()". Set
"ppxfer[n]" when the transfer setup is complete to prevent races. Remove
redundant NULL-checks from "usb2_transfer_unsetup()".
Submitted by: Hans Petter Selasky
- The software computed HID size is not always correct, because the algoritm
does not handle unsorted HID descriptors.
- Change the way we obtain the report ID.
- Use the X/Y/Z+button locations instead for report ID source for ums.
- Add more range checks.
- Remove Microsoft Mouse quirks. If the positions are moduloed the report
length multiplied by 8, the values seem correct.
- Some minor style changes.
Submitted by: Hans Petter Selasky
name) (not sure whether this works correctly, but should be close).
Fix the stub attach phase for some Novatel cards. They expect the CSW
(repsonse to CBW, SCSI eject command) to be fetched before switching to
modem mode.
MFC after: 2 weeks
