We should just leave the underlying TTY objects alone when scrolling
around in KDB. It should be handled by Syscons exclusively.
Reported by: pluknet gmail com
address space sizes to be longs instead of ints. Specifically, the follow
values are now longs: runningbufspace, bufspace, maxbufspace,
bufmallocspace, maxbufmallocspace, lobufspace, hibufspace, lorunningspace,
hirunningspace, maxswzone, maxbcache, and maxpipekva. Previously, a
relatively small number (~ 44000) of buffers set in kern.nbuf would result
in integer overflows resulting either in hangs or bogus values of
hidirtybuffers and lodirtybuffers. Now one has to overflow a long to see
such problems. There was a check for a nbuf setting that would cause
overflows in the auto-tuning of nbuf. I've changed it to always check and
cap nbuf but warn if a user-supplied tunable would cause overflow.
Note that this changes the ABI of several sysctls that are used by things
like top(1), etc., so any MFC would probably require a some gross shims
to allow for that.
MFC after: 1 month
debug.hashstat.rawnchash sysctl in particular as taking 7 milliseconds on
a 3GHz Intel Xeon (4x2) running 7.1. It accounted for almost a quarter of
the total runtime of 'sysctl -a'. It also performs lots of copyout's while
holding the namecache lock (this does not attempt to fix that).
MFC after: 2 weeks
IPv4 stack.
Diffs are minimized against p4.
PCS has been used for some protocol verification, more widespread
testing of recorded sources in Group-and-Source queries is needed.
sizeof(struct igmpstat) has changed.
__FreeBSD_version is bumped to 800070.
in make.conf or src.conf.
- When GPT is enabled (which it is by default), use memory above 1 MB and
leave the memory from the end of the bss to the end of the 640k window
purely for the stack. The loader has grown and now it is much more
common for the heap and stack to grow into each other when both are
located in the 640k window.
PR: kern/129526
MFC after: 1 week
ports tree so that programs use libusb from the base by default. Thanks to
Stanislav Sedov for sorting out the ports build.
Bump __FreeBSD_version to 800069
Help and testing by: stas
was introduced. If you have a bus, say cardbus, that is derived from
a base-bus (say PCI), then ordinarily all PCI drivers would attach to
cardbus devices. However, there had been one exception: kldload
wouldn't work.
The problem is in devclass_add_driver. In this routine, all we did
was call to the pci device's BUS_DRIVER_ADDED routine. However, since
cardbus bus instances had a different devclass, none of them were
called.
The solution is to call all subclass devclasses, recursively down the
tree, of the class that was loaded. Since we don't have a 'children
class' pointer, we search the whole list of devclasses for a class
whose parent matches. Since just done a kldload time, this isn't as
bad as it sounds. In addition, we short-circuit the whole process by
marking those classes with subclasses with a flag. We'll likely have
to reevaluate this method the number of devclasses with subclasses
gets large.
This means we can remove the "cardbus" lines from all the PCI drivers
since we have no cardbus specific attach device attachments in the
tree.
# Also: minor tweak to an error message
unlikely but not impossible given modern thread counts) wrap-around,
and the compiler was padding it out to an int (at least) anyway.
MFC after: 3 days (but confirm ABI impact)
system call entry path and i386 IP checksum generation: we now assume
all code is MPSAFE unless explicitly marked otherwise. Remove XXX
Giant comments along similar lines: the code by the comments either
doesn't need or doesn't want Giant (especially the NMI handler).
MFC after: 3 days
not there is an audit record hung off of td_ar on the current thread.
Test this flag instead of td_ar when auditing syscall arguments or
checking for an audit record to commit on syscall return. Under
these circumstances, td_pflags is much more likely to be in the cache
(especially if there is no auditing of the current system call), so
this should help reduce cache misses in the system call return path.
MFC after: 1 week
Reported by: kris
Obtained from: TrustedBSD Project
get default next page configuration. While I'm here explicitly set
IP1000PHY_ANAR_CSMA bit. This bit is read-only and always set
by hardware so setting it has no effect but it would clear the
intention. With this change controllers that couldn't establish
1000baseT link should work.
PR: kern/130846
mapping. The tunable is OFF for all controllers except RTL8169SC
family. RTL8169SC seems to require more magic to use memory
register mapping. r187483 added a fix for RTL8169SCe controller but
it does not looke like fix other variants of RTL8169SC.
Tested by: Gavin Stone-Tolcher g.stone-tolcher <> its dot uq dot edu dot au
o correct dBm<->mW conversion logic
o set net80211 TXPMGT capability only if driver reports it is capable
PR: kern/132342
Submitted by: "Paul B. Mahol" <onemda@gmail.com>
Fix bugs and improve HID parsing.
- fix possible memory leak found
- fix possible NULL pointer access
- fix possible invalid memory read
- parsing improvements
- reset item data position when a new report ID is detected.
Submitted by: Hans Petter Selasky
query functions in the kernel, as these effectively serialize
parallel calls to the gettimeofday(2) system call, as well as
other kernel services that use timestamps.
Use the NetBSD version of the fix (kern_tc.c:1.32 by ad@) as
they have picked up our timecounter code and also ran into the
same problem.
Reported by: kris
Obtained from: NetBSD
MFC after: 3 days
locks: a global list/counter/generation counter protected by a new
mutex unp_list_lock, and a global linkage rwlock, unp_global_rwlock,
which protects the connections between UNIX domain sockets.
This eliminates conditional lock acquisition that was previously a
property of the global lock being held over sonewconn() leading to a
call to uipc_attach(), which also required the global lock, but
couldn't rely on it as other paths existed to uipc_attach() that
didn't hold it: now uipc_attach() uses only the list lock, which
follows the linkage lock in the lock order. It may also reduce
contention on the global lock for some workloads.
Add global UNIX domain socket locks to hard-coded witness lock
order.
MFC after: 1 week
Discussed with: kris
A difference between the old and the new TTY layer is that the new
implementation does not perform any post-processing before returning
data back to userspace when calling read().
sh(1)'s read turns the TTY into a raw mode before calling select(). This
means that the first character will not receive any ICRNL processing.
Inherit this flag from the original terminal attributes.
Even though this issue is not present on RELENG_*, I'm MFCing it to make
sh(1) in jails behave better.
PR: bin/129566
MFC after: 2 weeks
