This also involves adding a quirk table as TRIM is broken for some
Kingston eMMC devices, though. Compared to ERASE (declared "legacy"
in the eMMC specification v5.1), TRIM has the advantage of operating
on write sectors rather than on erase sectors, which typically are
of a much larger size. Thus, employing TRIM, we don't need to fiddle
with coalescing BIO_DELETE requests that are also of (write) sector
units into erase sectors, which might not even add up in all cases.
- For some SanDisk iNAND devices, the CMD38 argument, e. g. ERASE,
TRIM etc., has to be specified via EXT_CSD[113], which now is also
handled via a quirk.
- My initial understanding was that for eMMC partitions, the granularity
should be used as erase sector size, e. g. 128 KB for boot partitions.
However, rereading the relevant parts of the eMMC specification v5.1,
this isn't actually correct. So drop the code which used partition
granularities for delmaxsize and stripesize. For the most part, this
change is a NOP, though, because a) for ERASE, mmcsd_delete() used
the erase sector size unconditionally for all partitions anyway and
b) g_disk_limit() doesn't actually take the stripesize into account.
- Take some more advantage of mmcsd_errmsg() in mmcsd(4) for making
error codes human readable.
sdhci(4), mmc(4) and mmcsd(4). For the most part, this consists of:
- Correcting and extending the infrastructure for negotiating and
enabling post-DDR52 modes already added as part of r315598. In
fact, HS400ES now should work as well but hasn't been activated
due to lack of corresponding hardware.
- Adding support executing standard SDHCI initial tuning as well
as re-tuning as required for eMMC HS200/HS400 and the fast UHS-I
SD card modes. Currently, corresponding methods are only hooked
up to the ACPI and PCI front-ends of sdhci(4), though. Moreover,
sdhci(4) won't offer any modes requiring (re-)tuning to the MMC/SD
layer in order to not break operations with other sdhci(4) front-
ends. Likewise, sdhci(4) now no longer offers modes requiring the
set_uhs_timing method introduced in r315598 to be implemented/
hooked up (previously, this method was used with DDR52 only, which
in turn is only available with Intel controllers so far, i. e. no
such limitation was necessary before). Similarly for 1.2/1.8 V VCCQ
support and the switch_vccq method.
- Addition of locking to the IOCTL half of mmcsd(4) to prevent races
with detachment and suspension, especially since it's required to
immediately switch away from RPMB partitions again after an access
to these (so re-tuning can take place anew, given that the current
eMMC specification v5.1 doesn't allow tuning commands to be issued
with a RPMB partition selected). Therefore, the existing part_mtx
lock in the mmcsd(4) softc is additionally renamed to disk_mtx in
order to denote that it only refers to the disk(9) half, likewise
for corresponding macros.
On the system where the addition of DDR52 support increased the read
throughput to ~80 MB/s (from ~45 MB/s at high speed), HS200 yields
~154 MB/s and HS400 ~187 MB/s, i. e. performance now has more than
quadrupled compared to pre-r315598.
Also, with the advent of (re-)tuning support, most infrastructure
necessary for SD card UHS-I modes up to SDR104 now is also in place.
Note, though, that the standard SDHCI way of (re-)tuning is special
in several ways, which also is why sending the actual tuning requests
to the device is part of sdhci(4). SDHCI implementations not following
the specification, MMC and non-SDHCI SD card controllers likely will
use a generic implementation in the MMC/SD layer for executing tuning,
which hasn't been written so far, though.
However, in fact this isn't a feature-only change; there are boards
based on Intel Bay Trail where DDR52 is problematic and the suggested
workaround is to use HS200 mode instead. So far exact details are
unknown, however, i. e. whether that's due to a defect in these SoCs
or on the boards.
Moreover, due to the above changes requiring to be aware of possible
MMC siblings in the fast path of mmc(4), corresponding information
now is cached in mmc_softc. As a side-effect, mmc_calculate_clock(),
mmc_delete_cards(), mmc_discover_cards() and mmc_rescan_cards() now
all are guaranteed to operate on the same set of devices as there no
longer is any use of device_get_children(9), which can fail in low
memory situations. Likewise, mmc_calculate_clock() now longer will
trigger a panic due to the latter.
o Fix a bug in the failure reporting of mmcsd_delete(); in case of an
error when the starting block of a previously stored erase request
is used (in order to be able to erase a full erase sector worth of
data), the starting block of the newly supplied bio_pblkno has to be
returned for indicating no progress. Otherwise, upper layers might
be told that a negative number of BIOs have been completed, leading
to a panic.
o Fix 2 bugs on resume:
- Things done in fork1(9) like the acquisition of an SX lock or the
sleepable memory allocation are incompatible with a MTX_DEF taken.
Thus, mmcsd_resume() must not call kproc_create(9), which in turn
uses fork1(9), with the disk_mtx (formerly part_mtx) held.
- In mmc_suspend(), the bus is powered down, which in the typical
case of a device being selected at the time of suspension, causes
the device deselection as part of the bus acquisition by mmc(4) in
mmc_scan() to fail as the bus isn't powered up again before later
in mmc_go_discovery(). Thus, power down with the bus acquired in
mmc_suspend(), which will trigger the deselection up-front.
o Fix a memory leak in mmcsd_ioctl() in case copyin(9) fails. [1]
o Fix missing variable initialization in mmc_switch_status(). [2]
o Fix R1_SWITCH_ERROR detection in mmc_switch_status(). [3]
o Handle the case of device_add_child(9) failing, for example due to
a memory shortage, gracefully in mmc(4) and sdhci(4), including not
leaking memory for the instance variables in case of mmc(4) (which
might or might not fix [4] as the latter problem has been discovered
independently).
o Handle the case of an unknown SD CSD version in mmc_decode_csd_sd()
gracefully instead of calling panic(9).
o Again, check and handle the return values of some additional function
calls in mmc(4) instead of assuming that everything went right or mark
non-fatal errors by casting the return value to void.
o Correct a typo in the Linux IOCTL compatibility; it should have been
MMC_IOC_MULTI_CMD rather than MMC_IOC_CMD_MULTI.
o Now that we are reaching ever faster speeds (more improvement in this
regard is to be expected when adding ADMA support to sdhci(4)), apply
a few micro-optimizations like predicting mmc(4) and sdhci(4) debugging
to be off or caching erase sector and maximum data sizes as well support
of block addressing in mmsd(4) (instead of doing 2 indirections on every
read/write request for determining the maximum data size for example).
Reported by: Coverity
CID: 1372612 [1], 1372624 [2], 1372594 [3], 1007069 [4]
mmc(4). For the most part, this consists of support for:
- Switching the signal voltage (VCCQ) to 1.8 V or (if supported
by the host controller) to 1.2 V,
- setting the UHS mode as appropriate in the SDHCI_HOST_CONTROL2
register,
- setting the power class in the eMMC device according to the
core supply voltage (VCC),
- using different bits for enabling a bus width of 4 and 8 bits
in the the eMMC device at DDR or higher timings respectively,
- arbitrating timings faster than high speed if there actually
are additional devices on the same MMC bus.
Given that support for DDR52 is not denoted by SDHCI capability
registers, availability of that timing is indicated by a new
quirk SDHCI_QUIRK_MMC_DDR52 and only enabled for Intel SDHCI
controllers so far. Generally, what it takes for a sdhci(4)
front-end to enable support for DDR52 is to hook up the bridge
method mmcbr_switch_vccq (which especially for 1.2 V signaling
support is chip/board specific) and the sdhci_set_uhs_timing
sdhci(4) method.
As a side-effect, this change also fixes communication with
some eMMC devices at SDR high speed mode with 52 MHz due to
the signaling voltage and UHS bits in the SDHCI controller no
longer being left in an inappropriate state.
Compared to 52 MHz at SDR high speed which typically yields
~45 MB/s with the eMMC chips tested, throughput goes up to
~80 MB/s at DDR52.
Additionally, this change already adds infrastructure and quite
some code for modes up to HS400ES and SDR104 respectively (I did
not want to add to much stuff at a time, though). Essentially,
what is still missing in order to be able to activate support
for these latter is is support for and handling of (re-)tuning.
o In sdhci(4), add two tunables hw.sdhci.quirk_clear as well as
hw.sdhci.quirk_set, which (when hooked up in the front-end)
allow to set/clear sdhci(4) quirks for debugging and testing
purposes. However, especially for SDHCI controllers on the
PCI bus which have no specific support code so far and, thus,
are picked up as generic SDHCI controllers, hw.sdhci.quirk_set
allows for setting the necessary quirks (if required).
o In mmc(4), check and handle the return values of some more
function calls instead of assuming that everything went right.
In case failures actually are not problematic, indicate that
by casting the return value to void.
Reviewed by: jmcneill
the default partition, eMMC v4.41 and later devices can additionally
provide up to:
1 enhanced user data area partition
2 boot partitions
1 RPMB (Replay Protected Memory Block) partition
4 general purpose partitions (optionally with a enhanced or extended
attribute)
Of these "partitions", only the enhanced user data area one actually
slices the user data area partition and, thus, gets handled with the
help of geom_flashmap(4). The other types of partitions have address
space independent from the default partition and need to be switched
to via CMD6 (SWITCH), i. e. constitute a set of additional "disks".
The second kind of these "partitions" doesn't fit that well into the
design of mmc(4) and mmcsd(4). I've decided to let mmcsd(4) hook all
of these "partitions" up as disk(9)'s (except for the RPMB partition
as it didn't seem to make much sense to be able to put a file-system
there and may require authentication; therefore, RPMB partitions are
solely accessible via the newly added IOCTL interface currently; see
also below). This approach for one resulted in cleaner code. Second,
it retains the notion of mmcsd(4) children corresponding to a single
physical device each. With the addition of some layering violations,
it also would have been possible for mmc(4) to add separate mmcsd(4)
instances with one disk each for all of these "partitions", however.
Still, both mmc(4) and mmcsd(4) share some common code now e. g. for
issuing CMD6, which has been factored out into mmc_subr.c.
Besides simply subdividing eMMC devices, some Intel NUCs having UEFI
code in the boot partitions etc., another use case for the partition
support is the activation of pseudo-SLC mode, which manufacturers of
eMMC chips typically associate with the enhanced user data area and/
or the enhanced attribute of general purpose partitions.
CAVEAT EMPTOR: Partitioning eMMC devices is a one-time operation.
- Now that properly issuing CMD6 is crucial (so data isn't written to
the wrong partition for example), make a step into the direction of
correctly handling the timeout for these commands in the MMC layer.
Also, do a SEND_STATUS when CMD6 is invoked with an R1B response as
recommended by relevant specifications. However, quite some work is
left to be done in this regard; all other R1B-type commands done by
the MMC layer also should be followed by a SEND_STATUS (CMD13), the
erase timeout calculations/handling as documented in specifications
are entirely ignored so far, the MMC layer doesn't provide timeouts
applicable up to the bridge drivers and at least sdhci(4) currently
is hardcoding 1 s as timeout for all command types unconditionally.
Let alone already available return codes often not being checked in
the MMC layer ...
- Add an IOCTL interface to mmcsd(4); this is sufficiently compatible
with Linux so that the GNU mmc-utils can be ported to and used with
FreeBSD (note that due to the remaining deficiencies outlined above
SANITIZE operations issued by/with `mmc` currently most likely will
fail). These latter will be added to ports as sysutils/mmc-utils in
a bit. Among others, the `mmc` tool of the GNU mmc-utils allows for
partitioning eMMC devices (tested working).
- For devices following the eMMC specification v4.41 or later, year 0
is 2013 rather than 1997; so correct this for assembling the device
ID string properly.
- Let mmcsd.ko depend on mmc.ko. Additionally, bump MMC_VERSION as at
least for some of the above a matching pair is required.
- In the ACPI front-end of sdhci(4) describe the Intel eMMC and SDXC
controllers as such in order to match the PCI one.
Additionally, in the entry for the 80860F14 SDXC controller remove
the eMMC-only SDHCI_QUIRK_INTEL_POWER_UP_RESET.
OKed by: imp
Submitted by: ian (mmc_switch_status() implementation)
comments, marking unused parameters as such, style(9), whitespace,
etc.
o In the mmc(4) bridges and sdhci(4) (bus) front-ends:
- Remove redundant assignments of the default bus_generic_print_child
device method (I've whipped these out of the tree as part of r227843
once, but they keep coming back ...),
- use DEVMETHOD_END,
- use NULL instead of 0 for pointers.
o Trim/adjust includes.
a DRIVER_MODULE() referencing mmc_driver has a MODULE_DEPEND() on mmc. This
is because the kernel linker only searches for symbols in dependent modules,
so loading sdhci_pci (and other bus-flavors of sdhci) would fail when mmc
was not compiled into the kernel (even if you hand-loaded mmc first).
(Thanks to jilles@ for providing the vital clue about the kernel linker.)
with some cards that causes them to become deselected after probing for
switch capabilities. The old workaround fixes the behavior with some cards,
but causes problems with the cards the behave correctly and don't become
deselected. Forcing a deselect then reselect appears to work correctly
with all cards in initial testing.
This is based on the patch sent by Alexander Fedorov with the following
fixes/improvements:
- Better error handling;
- Clock is derived from PLL6 (obtained from netbsd);
- No more unnecessary busy loops on interrupt handler;
- style(9) fixes and code cleanup.
I also want to thanks Martin Galvan who has sent an alternative
implementation with some interesting fixes.
Tested on CubieBoard2, Banana-Pi (thanks to netgate!) and Cubieboard1
(Pratik Singhal).
This is intended to pave the way for the upcoming GSoC work (and make
easier the build of images for the supported boards).
PR: 196081
Submitted by: Alexander Fedorov <alexander.fedorov@rtlservice.com>
boards, this prevents some error messages during enumeration and also
gives us the correct erase block size. They appear to be harmless
elsewhere.
# Note: we treat too many commands as 'can't fail' if they don't work
# after a couple of retries. We need to fix that, but not today...
specially aml8726-m6 and aml8726-m8b SoC based devices.
aml8726-m6 SoC exist in devices such as Visson ATV-102.
Hardkernel ODROID-C1 board has aml8726-m8b SoC.
The following support is included:
Basic machdep code
SMP
Interrupt controller
Clock control driver (aka gate)
Pinctrl
Timer
Real time clock
UART
GPIO
I2C
SD controller
SDXC controller
USB
Watchdog
Random number generator
PLL / Clock frequency measurement
Frame buffer
Submitted by: John Wehle
Approved by: stas (mentor)
Summary:
For new eMMC chips, we must signal controller HC capability in OP_COND command.
Reviewers: imp, ian
Reviewed By: ian
Differential Revision: https://reviews.freebsd.org/D1920
deselect it after setting the block size. This is a similar bug that
was fixed elsewhere, but not here. This makes sure that we leave the
card deselected at the end of the loop, and we don't send any commands
to the card without it selected.
Reviewed by: ian@
such as timeouts while probing a bus or testing for a feature, is
squelched. Also, error reporting is limited to 5 events per second,
because when an sdcard goes bad on a low-end embedded board, flooding
the console at high speed isn't helpful.
Original logging code contributed by Michal Meloun, but then I fancied
it up with squelching and ppsratecheck.
function parameters, the card has to be in transfer state. If it is in
the idle state, the commands are ignored. This caused us not to set
the proper parameters that we later assume to be present, leading to
downstream failures of the card / interface as our state machine
mismatches the card's.
Submitted by: Svatopluk Kraus <onwahe at gmail.com>, Michal Meloun
<meloun at miracle.cz>
In the mmcsd layer use this value to populate disk->d_ident. Also set
disk->d_descr to the full set of card identification info (includes vendor,
model, manufacturing date, etc).
mode. We don't know why it failed, so we can't know that a retry will
also fail (the low-level driver might have reset the controller state
machine or something similar that would allow a retry to work).
The MMCHS hardware is pretty much a standard SDHCI v2.0 controller with a
couple quirks, which are now supported by sdhci(4) as of r254507.
This should work for all TI SoCs that use the MMCHS hardware, but it has
only been tested on AM335x right now, so this enables it on those platforms
but leaves the existing ti_mmchs driver in place for other OMAP variants
until they can be tested.
This initial incarnation lacks DMA support (coming soon). Even without it
this improves performance pretty noticibly over the ti_mmchs driver,
primarily because it now does multiblock IO.
ensure that all such commands have a non-zero retry count except for those
that are expected to fail (for example, because they are used to probe for
feature support).
While it is possible to pass a retry count down to the hardware driver in
the command request structure, no hardware driver currently implements any
retry logic. The hardware doesn't know much about the context of a single
request, so it makes more sense to handle retries at a layer that does.
This adds retry loops to the mmc_wait_for_cmd() and mmc_wait_for_app_cmd()
functions. These functions are the gateway from other code within mmc.c
to the hardware. App commands are a sequence of two commands and a retry
has to rerun both of them in order, so it needs its own retry loop.
Retry looping is specifically NOT implemented in mmc_wait_for_request()
because it is the gateway for children on the bus, and they have to
implement their own retry logic depending on what makes sense for them.
sdchi encapsulates a generic SD Host Controller logic that relies on
actual hardware driver for register access.
sdhci_pci implements driver for PCI SDHC controllers using new SDHCI
interface
No kernel config modifications are required, but if you load sdhc
as a module you must switch to sdhci_pci instead.
- Fix some math errors in mmc_decode_csd_sd().
- Fix incorrect arguments to mmc_send_app_op_cond() in mmc_go_discovery().
- Add reporting of CSD for debug purposes.
- Add detection (and skipping) of password-locked cards.
- Add setting of block length on card if necessary.
Submitted by: Patrick Kelsey
MFC after: 3 days
- When switching to 4-bit operation, send a SET_CLR_CARD_DETECT command
to disconnect the card-detect pull-up resistor from the DAT3 line before
sending the SET_BUS_WIDTH command.
- Add the missing "reserved" zero entry to the mantissa table used to
decode various CSD fields. This was causing SD cards to report that they
could run at 30 MHz instead of the maximum 25 MHz mandated in the spec.
o Enhancements:
- At the MMC layer, format various info from the CID into a string that
uniquely identifies the card instance (manufacturer number, serial
number, product name and revision, etc). Export it as an instance
variable.
- At the MMCSD layer, display the formatted card ID string, and also
report the clock speed of the hardware (not the card's max speed), and
the number of bits and number of blocks per transfer. It comes out like
this now:
mmcsd0: 968MB <SD SD01G 8.0 SN 276886905 MFG 08/2008 by 3 SD> at mmc0
22.5MHz/4bit/128-block
o Use DEVMETHOD_END.
o Use NULL instead of 0 for pointers.
PR: 156496
Submitted by: Ian Lepore
MFC after: 1 week
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
1. Both mmc_read_ivar() and sdhci_read_ivar() use the expression
'*(int *)result = val' to assign to result which is uintptr_t *.
This does not work on big-endian 64 bit systems.
2. The media_size ivar is declared as 'off_t' which does not fit
into uintptr_t in 32bit systems, change this to long.
Submitted by: kanthms at netlogicmicro com (initial version)
