generations of 802.11abg chipsets from Ralink Technology.
Get rid of the pccard front-end while I'm here since all adapters are
cardbus ones.
Obtained from: OpenBSD
into a separate module. Accordingly, convert the option into a device
named similarly.
Note for MFC: Perhaps the option should stay in RELENG_6 for POLA reasons.
Suggested by: scottl
Reviewed by: cokane
MFC after: 5 days
to call back for completition and something else is holding the taskqueue
waiting for ATA to return data.
This should clear up the "semaphore timeout !! DANGER Will Robinson !!"
in most situations, and log "taskqueue timeout - completing request directly"
instead, with a delayed "WARNING - freeing taskqueue zombie request" when
the taskqueue finally calls us back with the now stale request.
(It would have been nice if there was a way to remove a scheduled item from
a taskqueue, but that is not currently implemented in the kernel).
A real fix for this is in the works but wont make it to 6.1RELEASE
definite MFC candidate.
- Don't use a common buffer in the softc to store per-command data. Reserve
a buffer in the command itself.
- Don't allocate DMA memory for the kernel command structures when all you
really need is DMA memory for the scratch buffer embedded in them. Instead
allocate a slab for the scratch buffers and divide it up as needed.
- Call bus_dmamap_unload() at the completion of commands.
- Preserve and clear the CAM CCB status flags at completion.
- Reorder some low-level command operations to try to close races.
- Limit the simq to 32 commands for now. There are some serious problems
with the driver under load that are not well understood, so keeping the
simq lower helps avoid this. It has been tested at a higher value, but
this is a safe value that doesn't show much performance degredation.
These changes allow the driver to work reliably with >4GB of memory on i386
and amd64, and also work around deadlocks seen under very high load in
certain situations. The work-around is far from ideal, but without and
documentation it is hard to know what the right fix is.
MFC candidate
By default syscons(4) will look for the kbdmux(4) keyboard first, and then,
if not found, look for any keyboard.
Current kbd code is modified so if kbdmux(4) is the current keyboard, all
new keyboards are automatically added to the kbdmux(4).
Switch to kbdmux(4) can be done at boot time, by loading kbdmux module at
the loader prompt, or at runtime, by kldload'ing the kbdmux module and
releasing current active keyboard.
If, for whatever reason, kbdmux(4) is not required/desired then just do
not load it and everything should work as before. It is also possible to
kldunload kbdmux at runtime and syscons(4) will automatically switch to
the first available keyboard.
No response from: freebsd-current@
MFC after: 1 day
mpt_soft_reset more than once. And to wait for MPT_DB_STATE_READY
twice. I mean, this is crucial- give the IOC a chance to get
ready.
If mpt_reset is called to reinit things, and we succeed, make
sure to re-enable interrupts. This is what has mostly led to
system lockup after having to hard reset the chip. Also, if
we think that interrupts aren't function in mpt_cam_timeout,
for goodness sake, turn them on again.
In read_cfg_header, return distinguishing errnos so the caller
can decide what's an error. It's *not* an error to fail to
read a RAID page from a non-RAID capable device like the FC929X.
Some whitespace fixes (removing spaces from ends of lines).
Developed with: Norbert Koch < NKoch at demig dot de >
No response from: freebsd-current@
Tested by: Norbert Koch < NKoch at demig dot de >
MFC after: 1 day
not hang the system for 5 seconds. If a TMF doesn't complete within,
oh, say 500ms, that's enough.
Put in a printout to catch mpt_recover_commands being activated with
no commands.
*both* SAS and FC, not just SAS.
b) Don't tell the chip we want it to do FIFO signalling if we actually
don't set up the address where the FIFO signal is supposed to be written
(oops).
is closed and then reopened. This appears to be necessary now that
we no longer clear endpoint stalls every time a pipe is opened.
Previously we could assume an initial toggle value of zero because
the clear-stall operation resets the device's toggle state.
Reported by: Holger Kipp
MFC after: 3 days
(atkbd(4)) and PS/2 mouse (psm(4)) are used together.
Turns out that atkbd(4) check_char() method may return "true" while
read_char() method returns NOKEY. When this happens kbdmux(4) was
simply stuck in the dead loop. Avoid dead loop in kbdmux(4) by breaking
out of the loop if read_char() method returns NOKEY.
It almost seems like a bug in atkkbd(4), atkbd_check_char() calls
kbdc_data_ready(), and, the later will return "true" if there are
pending data in either kbd or aux queue. However, because both aux
and kbd are on the same controller, I'm not sure if this is a bug
or feature.
Tested by: markus
MFC after: 1 day
is finished with it; this may only occur when the tx queue is setup as
dba-gated but since the fix is cheap apply it to all queues
while here make the queue depth signed for use in assertions
Reviewed by: apatti
MFC after: 2 weeks
Return BUS_PROBE_LOW_PRIORITY for a successful probe. This is in
preparation of the introduction of scc(4), which is going to handle
SCCs in the near future.
mutex.
- Don't use callout_drain() to stop the toffhandle callout while holding the
fdc mutex (this could deadlock) in functions called from softclock
(callouts aren't allowed to do voluntary sleeps). Instead, use
callout_stop(). Note that since we hold the associated mutex and are now
using callout_init_mtx(), callout_stop() is just as effective as
callout_drain(). (Though callout_drain() is still needed in detach to
make sure softclock isn't contesting on our mutex before we destroy the
mutex.)
- Remove unused callout 'tohandle' from softc.
MFC after: 1 week
interrupt handlers rather than BUS_SETUP_INTR() and BUS_TEARDOWN_INTR().
Uses of the BUS_*() versions in the implementation of foo_intr methods
in bus drivers were not changed. Mostly this just means that some
drivers might start printing diagnostic messages like [FAST] when
appropriate as well as honoring mpsafenet=0.
- Fix two more of the ppbus drivers' identify routines to function
correctly in the mythical case of a machine with more than one ppbus.
processing the interrupt events. If we clear them afterwards we
can completely miss some events as the NIC can change the source
flags while we're in the handler. In order to not get another
interrupt while we're in ifp->if_input() with the driver lock
dropped we now turn off NIC interrupts while in the interrupt
handler. Previously this was meant to be achieved by clearing the
interrupt source flags after processing the interrupt events but
didn't really work as clearing these flags doesn't actually
acknowledge and re-enable the events.
This fixes the device timeouts seen with the VMware LANCE.
- Relax the watchdog timer somewhat; don't enable it until the last
packet is enqueued and if there is a TX interrupt but there are
still outstanding ones reload the timer.
Reported and tested by: Morten Rodal <morten@rodal.no>
MFC after: 3 days
The ed driver on pc98 was broken by if_edvar.h rev1.31.
Reported by: Kaho Toshikazu (kaho at elam kais kyoto-u ac jp)
Tested by: Eiji Kato (ekato at a1 mbn or jp)
MFC after: 3 days
More info regarding these nics can be found at http://www.myri.com.
Please note that the files
sys/dev/myri10ge/{mcp_gen_header.h,myri10ge_mcp.h} are internally
shared between all our drivers (solaris, macosx, windows, linux, etc).
I'd like to keep these files unchanged, so I can just import newer
versions of them when the firmware API/ABI changes. This means I'm
stuck with some of the crazy-long #define names, and possibly
non-style(9) characteristics of these files.
Many thanks to mlaier for doing firmware(9) just as I
needed it, and to scottl for his helpful review.
Reviewed by: scottl, glebius
Sponsored by: Myricom Inc.
forcing DMA alignment to default buffer size.
- Make sure DMA pointer properly aligned to avoid being truncated by caller
which causing severe underruns and random popping (especially in 32bit
playback / recording).
- Add AC97 inverted external amplifier quirk for Maxselect x710s
- http://maxselect.ru/
MFC after: 1 week
the SMI/TCO address space. Switch the bus space I/O to the
one specific for either the SMI or TCO space. Re-calibrate
the tick. Add some more device id's, 82801FBR submitted by des.
This makes it work on the platforms I've tested with.
Go ahead by: des
should fix strange link state behaviour reported for bcm5721 & bcm5704c
2) Clear bge_link flag in bge_stop()
3) Force link state check after bge_ifmedia_upd(). Otherwise we can miss link
event if PHY changes it's state fast enough.
Tested by: phk (bcm5704c)
Approved by: glebius (mentor)
MFC after: 1 week
Acknowledgement should definitly go to JMicron Technology for providing full
docs on the metadata format as the only vendor so far, big thanks from here.
- In em_attach() remove em_check_for_link(). Not needed here, since
already done in em_hardware_init().
- In em_attach() replace the printing block with call to
em_update_link_status().
- Remove modification of sc->link_state from em_hardware_init() and
from em_media_status(). This makes em_update_link_status() a
single point of change. Call em_update_link_status() where needed.
to getting rid u_int for uint and so on).
b) Turn back on 64 bit DAC support. Cheeze it a bit in that we have two
DMA callback functions- one when we have bus_addr_t > 4 bits in width and
the other which should be normal. Even Cheezier in that we turn off setting
up DMA maps to be BUS_SPACE_MAXADDR if we're in ISP_TARGET_MODE. More work
on this in a week or so.
c) Tested under amd64 and 1MB DFLTPHYS, sparc64, i386 (PAE, but insufficient
memory to really test > 4GB). LINT check under amd64.
MFC after: 1 month
automatically both SATA and SAS drives. The async SAS event handling we catch
but ignore at present (so automagic attach/detach isn't hooked up yet).
Do 64 bit PCI support- we can now work on systems with > 4GB of memory.
Do large transfer support- we now can support up to reported chain depth, or
the length of our request area. We simply allocate additional request elements
when we would run out of room for chain lists.
Tested on Ultra320, FC and SAS controllers on AMD64 and i386 platforms.
There were no RAID cards available for me to regression test.
The error recovery for this driver still is pretty bad.
to work with ipmitools. It works with other tools that have an OpenIPMI
driver interface. The port will need to get updated to used this.
I have not implemented the IPMB mode yet so ioctl's for that don't
really do much otherwise it should work like the OpenIPMI version.
The ipmi.h definitions was derived from the ipmitool header file.
The bus attachments are done for smbios and pci/smbios. Differences
in bus probe order for modules/static are delt with. ACPI attachment
should be done.
This drivers registers with the watchdod(4) interface
Work to do:
- BT interface
- IPMB mode
This has been tested on Dell PE2850, PE2650 & PE850 with i386 & amd64
kernel.
I will link this into the build on next week.
Tom Rhodes, helped me with the man page.
Sponsored by: IronPort Systems Inc.
Inspired from: ipmitool & Linux
o add dfs+radar hooks; DFS is presently disabled in the hal
o channel and mode handling changes
o various api changes
o be more aggressive about iq calibration settling so ap mode
operation is better immediately after startup
o rfkill/rfsilent sysctl support
o tpc ack/cts sysctl support
MFC after: 2 weeks
o assume all data frames have been classified so there's no need
to check if QoS is being used, just fetch the wme priority from
the mbuf
o fix double counting of noack frames
o fix nearby comment
MFC after: 2 weeks
o pull nexttbtt forward in adhoc mode too
o resync beacon timers on joining a bss or ibss as the tstamp we
collected while scanning is almost certainly out of date
Note we may need to refine the ibss mode check in ath_recv_mgmt.
Reviewed by: avatar, dyoung
Obtained from: atheros
MFC after: 2 weeks
frame and if we get a beacon miss interrupt ignore it if we've received
a frame within the beacon miss interval. This should never trigger
and the handling at the net80211 layer should likewise deal with this
but it doesn't hurt and can suppress extranous probe request frames.
Note that we can legtimately get a bmiss when under heavy load.
MFC after: 2 weeks
- Restart watchdog if we *did* processed any descriptors. [1]
- Log the watchdog event if the link is *up*. [2]
PR: kern/92948 [1]
Submitted by: Mihail Balikov <mihail.balikov interbgc.com> [1]
PR: kern/92895 [2]
Submitted by: Vladimir Ivanov <wawa yandex-team.ru> [2]
than just deleting them. Also add comments about why we do this.
Given the current behavior of delete_child, I don't think this changes
anything. It just feels cleaner.
dereferencing) since a NULL value would be a bug here.
Note: Both affected functions look very similar. A refactoring may
be beneficial.
CID: 483, 485
Found with: Coverity Prevent(tm)
Discussed with: ariff
MFC after: 5 days
needed here, except there's a bug which results in detaching the device
twice.
Move the NULL pointer check to the beginning of the function and convert
it into a KASSERT.
CID: 420
Found with: Coverity Prevent(tm)
Discussed with: ariff
MFC after: 5 days
Control) devices as console. These are microcontrollers which are either
on-board or part of an add-on card and provide terminal server, remote
power switch and monitoring functionality. For console usage these are
connected to the rest of the system via a SCC or an UART. This commit adds
support for the following variants (corresponds to what 'input-device' and
'output-device' have to be set to):
rsc found on-board in E250 and supposedly some Netra, connected
via a SAB82532, com. parameters can be determined via OFW
rsc-console RSC card found in E280R, Fire V4x0, Fire V8x0, connected
via a NS16550, hardwired to 115200 8N1
lom-console LOMlite2 card found in Netra 20/T4, connected via a NS16550,
hardwired to 9600 8N1
- Add my copyright to uart_cpu_sparc64.c as I've rewritten about one third
of that file over time.
Tested on: E250, E280R
Thanks to: dwhite@ for providing access to an E280R
OK'ed by: marcel
MFC after: 1 week
casting a structure to a uint32_t *. Many drivers in the tree do this, but
I'll not update them until these changes can be reviewed by the pedantic
standards folks.
in order to query the underlying Windows driver for the station address
and some other properties. There is a slim chance that the card may
receive a packet and indicate it up to us before ndis_attach() can call
ndis_halt_nic(). This is bad, because both the softc structure and
the ifnet structure aren't fully initialized yet: many pointers are
still NULL, so if we make it into ndis_rxeof(), we will panic.
To fix this, we need to do the following:
- Move the calls to IoAllocateWorkItem() to before the call to ndis_init_nic().
- Move the initialization of the RX DPC and status callback function pointers
to before ndis_init_nic() as well.
- Modify ndis_rxeof() to check if the IFF_DRV_RUNNING flag is set. If it
isn't, we return any supplied NDIS_PACKETs to the NIC without processing
them.
This fixes a crash than can occur when activating a wireless NIC in
close proximity to a very busy wireless network, reported by Ryan
Beasley (ryan%^$!ATgoddamnbastard-****!!!DOTorg.
MFC after: 3 days
are bus_addr_t, not bus_size_t.
In any case, turn off DAC support entirely until it is revamped to actually
work *correctly* for 64 bit platforms (not using a PAE definition and for
both initiator and target mode).
