- use pseudo-dma
- provide the same features and interface as sio
- support multiple boards
- fix bugs.
Some compile-time configuration constants are set to support higher
speeds and Cyclom-16Y's at a 30% relative cost in efficiency.
Cyclom-16Y support is untested.
adapted to FreeBSD by Heikki Suonsivu <hsu@cs.hut.fi>.
Submitted by: Andrew Werple <andrew@werple.apana.org.au> and
Heikki Suonsivu <hsu@cs.hut.fi>
Obtained from: NetBSD
Handles at least Trantor T130 and ProAudioSpectrum adapters.
The pas driver has consequently been removed.
This driver can be configured without without interrupts.
Manpage to follow when PAS16 has been edited in.
Reviewed by: phk
Submitted by: Serge Vakulenko, <vak@cronyx.ru>
floppy driver (or in the hardware?). It turned out to be caused by
spurious interrupts, right after an FDC reset.
Also major cleanup in the low-level structure, there are now functions
performing error-checks for the FDC I/O.
Submitted by: (mostly) Peter Dufault <dufault@FreeBSD.org>
be merged at some point)
New AMD family ethernet driver. Should support BICC,NE2100, TNIC,
AT1500 and anything else that uses a Lance/PCnet type chip. Only been
tested with the BICC so far though.
Still work to do on performance and MULTICAST support needs to be added
but it's basically working and I want the revision history from this
point on
date: 1994/05/22 12:35:38; author: joerg; state: Exp; lines: +6 -6
First round of floppy changes. Try making `fd' more robust.
New features:
. ioctl command for setting the drive type (density etc.); restricted
to the super-user
. ioctl for getting/seting `drive options'; currently only option
is FDOPT_NORETRY: inhibit the usual retries; used when verifying
a newly formatted track
Fixes:
. function prototypes
. made all internal functions `static'
. cleaned up & corrected .h files
. restructured, to make the chaotic function sequence more rational
. compiled with -Wall, and cleared all warnings
. introduced a mirror for the (write-only) `digital output register',
to avoid the current kludge
. device probing completed by seeking/recalibrating, and looking
for track 0 being found
. holding the controller down in reset state while it is idle (and
thus saving allot of headaches)
. make requests fail that are not a multiple of the (physical)
sector size
. removed the fixed physical sector size (512 bytes), allowing for any
size the controller could handle (128/256/512/1024 bytes)
. replaced some silly messages
. fixed the TRACE* macro usage, debugging reports should be complete
now again (debugging output is HUGE! though)
. removed fd_timeout for SEEK command; seeks are always reported by
the controller to succeed, since the `success' only refers to the
controller's idea of success - there is no hardware line to tell about
the seek end (other than the `track 0' line)
. catch SENSEI's that report about a `terminated due to READY changed'
status - could happen after a controller reset
. converted ``hz / <something>'' divide operations to divisors that are
powers of two, so gcc can optimize them into shifts
. write/format operations are checked against a write-protected medium
now *prior* starting the operation
. error reports of `invalid command' and `wrong cylinder' will cause
shortcuts in the retrier() now
. fixed a bug in the retrier() causing bogus block numbers to be reported
. fdformat() does care for errors now
Known Bugs:
. no attempts have been made (yet) to improve the performance
. sometimes, bogus ``seek/recalib failed'' messages are logged; this
is still a bug in the driver, but it's not harmful since it's
usually caught by the retrier()
Reviewed by:
Submitted by:
Obtained from:
This is the slowest and most stupid of our SCSI-drivers, but it is there
and it works. It has been tested with CD-ROM and disk.
It uses no interrupts, no DMA, just polled I/0.
Transfer-rate is <= 100Kbyte/sec.
If you set the jumpers on the board, you can change the unit-number and
you will be able to have four of these co-exist in one computer, why one
would do that is somewhat unclear though.
If I ever get my hand on the docs for this, I will improve it of course,
but for now we can install and access those CD-ROMs.
This driver supports all the DEC EtherWORKS III NICs (DE203, DE204,
and DE205) and the later DEC EtherWORKS II NICs (DE200, DE201, DE202,
DE422). DEPCA-style boards prior to the DE200 have not been tested
and may not work.
Submitted by: Matt Thomas (thomas@lkg.dec.com)
based originally on work by David Greenman and adapted to FreeBSD
(and cleaned up a bit) by myself. It supports the IBM Credit Card
Adapter for the IBM Thinkpad, and I've had no trouble making it work
on my Toshiba T1910 with a National `InfoMover' NE4100 PCMCIA ethernet
card (I'm commiting this message through it right now :-).
This is actually sneaking it in after feature-freeze, but it's just
too useful to pass up! As always, necessity is a mother.
