vfs_equalopts(). This allows vfs_sanitizeopts() to filter redundant
occurrences of these options. It was possible that for example both "ro"
and "rw" options became active concurrently.
PR: kern/133614
Discussed on: freebsd-hackers
MFC after: 1 month
Also, express this new maximum as a fraction of the kernel's address
space size rather than a constant so that increasing KVA_PAGES will
automatically increase this maximum. As a side-effect of this change,
kern.maxvnodes will automatically increase by a proportional amount.
While I'm here ensure that this change doesn't result in an unintended
increase in maxpipekva on i386. Calculate maxpipekva based upon the
size of the kernel address space and the amount of physical memory
instead of the size of the kmem map. The memory backing pipes is not
allocated from the kmem map. It is allocated from its own submap of
the kernel map. In short, it has no real connection to the kmem map.
(In fact, the commit messages for the maxpipekva auto-sizing talk
about using the kernel map size, cf. r117325 and r117391, even though
the implementation actually used the kmem map size.) Although the
calculation is now done differently, the resulting value for
maxpipekva should remain almost the same on i386. However, on amd64,
the value will be reduced by 2/3. This is intentional. The recent
change to VM_KMEM_SIZE_SCALE on amd64 for the benefit of ZFS also had
the unnecessary side-effect of increasing maxpipekva. This change is
effectively restoring maxpipekva on amd64 to its prior value.
Eliminate init_param3() since it is no longer used.
so there's no need to enable the RX of invalid frames just to do ANI.
The if_ath code and AR5212 ANI code setup the RX filter bits to enable
receiving OFDM/CCK errors if the device doesn't have the hardware
MIB counters. It isn't initialising it for the AR5416+ because all of
those chips have hardware MIB counters.
This fixes the odd (and performance affecting!) situation where if ani
is enabled (via sysctl dev.ath.X.intmit) then suddenly there's be a very
large volume of phy errors - which is good to track, but not what was
intended. Since each PHY error is a received (0 length) frame, it can
significantly tie up the RX side of things.
equal to secondary counters:
primary_localcnt = secondary_remotecnt
primary_remotecnt = secondary_localcnt
Previously it was done wrong and split-brain was observed after
primary had synchronized up-to-date data from secondary.
Approved by: pjd (mentor)
MFC after: 1 week
This (almost) gives us the address space back (at the bottom) that we lost
at the top.
Region 0 has traditionally been reserved for IA-32 emulation, which has not
been of great interest. By starting 64-bit processes at the 4G boundary we
at least preserve some of the advantages:
1. Any invalid pointer cast (from int to pointer and back) will still
always fail and not only when more than 4GB of memory is in use.
2. Memory sharing between 64-bit and 32-bit processes is still possibly
by using addresses < 4G.
It's still not ready for prime-time - there's some TX niggles with these 11n
cards that I'm still trying to wrap my head around, and AMPDU-TX is just not
implemented so things will come to a crashing halt if you're not careful.
"extended capabilities" to refer to the new set of capability structures
starting at offset 0x100 in config space for PCI-express devices. For now
both function names will still work. I will merge this to older branches
to ease driver portability, but 9.0 will ship with a new pci_find_extcap()
function that locates extended capabilities instead.
Reviewed by: imp
MFC after: 1 week
This fix modifies the const addac initval array, rather than modifying
a local copy. It means that running >1 AR9160 on a board may prove to
be unpredictable.
The AR5416 init path also does something similar, so supporting
>1 AR5416 of different revisions could cause problems.
The later fix will be to create a private copy of the Addac data
for the AR5416, AR9160 (and AR9100 when it's merged in) and then
modify that as needed.
Obtained From: Linux ath9k
I found this when trying to figure out why the RX PHY error count
didn't match the OFDM error count ANI was using. It turns out
there was two problems:
* What this commit addresses - using the wrong mask for OFDM errors,
and
* The RX filter is set incorrectly after a channel scan (at least)
even if interference mitigation is enabled by default.
ANI is still disabled by default for the AR5416 and later chips.
set as TCP.
- Eliminate the fully linear non-scatter/gather rx path, there is no
harm in using arrays of clusters for both TCP and UDP.
- Implement support for enabling/disabling per-vlan priority pause and
queues via sysctl.
makes booting more reliable (and working at all on USB sticks). While here,
move responsibility for setting up fstab into the various platform mk-*.sh
scripts.
Suggested by: many
bring it in line with the rest of the register initialisation.
I've verified that the 2/5ghz board values written to the
chip match what was previously written.
* add pspoll/uapsd queue setup defaults;
* enable the exponential backoff window rather than the random
backoff window when doing TX contention management.
would be a problem, make sure it isn't overwritten by whatever is in
there at cold reset.
This brings the > ar5416 init path treatment of AR_MISC_MODE.
report descriptor information, sysctl utility
will show it for us.
- Modify sysctl node description to make it more
understanable.
Found by: Alexander Best <arundel@freebsd.org>
Submitted by: Eygene Ryabinkin <rea@freebsd.org>
MFC after: 14 days
Approved by: thompsa (mentor)
We can use capsicum for secondary worker processes and hastctl.
When working as primary we drop privileges using chroot+setgid+setuid
still as we need to send ioctl(2)s to ggate device, for which capsicum
doesn't allow (yet).
X-MFC after: capsicum is merged to stable/8