except for setting it. Also remove count from aha and replace it with
optional.
Also add commented out pccard lines for all the old card drivers.
They have to be commented out until they are converted because it
causes problems in NEWCARD.
striped plexes. This prevents various panics introduced in the last
rewrite of the locking code.
Suffered by: "Niels Chr. Bank-Pedersen" <ncbp@bank-pedersen.dk>
Turn off semaphores. Nobody else implements them, and there is lots of
AML out there which does totally absurd things with them, meaning that
if we try to do the right thing we are guaranteed to fail.
Use acpi_EvaluateInteger where possible.
Use FuncName rather than &FuncName when passing function addresses.
Don't evaluate the _REG method when we attach to an address space -
AcpiInstallAddressSpaceHandler does it for us.
acpi_EvaluateInteger.
Use acpi_EvaluateInteger instead of doing things the hard way where
possible.
AcpiSetSystemSleepState (unofficial) becomes AcpiEnterSleepState.
Use the AcpiGbl_FADT pointer rather than searching for the FADT.
incompletely converting simplelocks to mutexes (COM_LOCK() is supposed
to hide the SMP locking internals, but it now depends on mutex interfaces
being visible).
- When used on a 33MHz PCI BUS, the 53C1010-66 revision 0
requires extra clocks to be inserted in data out phase.
Revision 1 is fixed.
- The 53C1010-33 revision 1 requires internal cycles to be
disabled due to possible contentions on IO registers.
Revision 2 is fixed.
Fix:
- The probing of HVD from GPIO3 bit by the driver was reversed.
The driver could misprobe the bus mode of a 825 or 875 chip
that was not previously initialized (no BIOS for example).
is going away soon anyways. Instead, don't pass MTX_RECURSE to mtx_init,
so that WITNESS will panic if the driver mutex is recursed on.
- Use MTX_DEF in mtx_init() instead of assuming that it will be 0.
even if mode PS/2 is forced with bootflags. As a matter of fact,
chipsets needs some extra configuration for accessing PS/2 mode
from ECP. The current patch is only relevant for generic chipsets
since specific code is supposed to deal with this during detection.
an override as a loader settable variable (fxp_iomap). fxp_iomap is
a bitmap of fxp units that should be configured to use PCI I/O space
in stead of PCI Memory space.
Reviewed by: Kees Jan Koster <dutchman@tccn.cs.kun.nl>, dg@freebsd.org
we must also inform the card of this change. Otherwise the sequencer
will traverse a corrupt list of SCBS. The side effects of this problem
were unknown SCBs completing in the qoutfifo or worse yet, panics due
to sequencer interrupts that referenced what, to the kernel, were invalid
SCB ids.
- Use proper atomic operations to make the run time initialization
controlled by svr_str_initialized be MP safe.
- Use appropriate queue(3) macros where needed.
Initialize rid to 0. This doesn't seem to make any difference
(the driver doesn't care what rid it gets and no-one seems to
check rid's value), but follows standard conventions.
Pass in our device_t to ahc_alloc(). We now use device_T
softc storage, so passing NULL results in a panic.
Set the unit number in our softc so that the driver core
can retrieve it.
ahc_pci.c:
Set the unit number in our softc so that the driver core
can retrieve it.
aic7770.c:
Insert our softc into the list of softcs when initialization
is successful.
aic7xxx.c:
Remove a workaround for an aic7895 bug we will never trigger.
Add additional diagnostic info to ahc_dump_card_state().
Always panic the system if a sequencer assertion fails.
AHC_SCB_BTT is a "flag" not a "feature". Check the right
field in the softc.
Replace a hard coded number with a constant.
Guard against looping forever in ahc_pause_and_flushwork().
A hot eject or card failure may make the intstat register
return 0xFF, so limit the number of interrupts we'll process.
Correct the code in ahc_search_qinfifo() that guarantees that
the sequencer will see an abort collision if the qinfifo is
modified when a DMA is in progress. We now do this fixup
after modifying the queue. This guarantees that the HSCB
we place at the head of the queue is not the same as the
old head. Using "next hscb" (guaranteed not to be the
same as the first SCB) before clearing the queue could free
up the original head hscb to be used during a remove operation
placing it again at the head of the qinfifo.
aic7xxx.h:
Reduce the maximum number of outstanding commands to 253 from
254. To handle our output queue correctly on machines that only
support 32bit stores, we must clear the array 4 bytes at a
time. To avoid colliding with a DMA write from the sequencer,
we must be sure that 4 slots are empty when we write to clear
the queue. This reduces us to 253 SCBs: 1 that just completed
and the known three additional empty slots in the queue that
preceed it. Yahoo was able to force this race on one of their
systems. Interrupts were disabled for such a time that the
entire output queue was filled (254 entries complete without
any processing), and our 32bit write to clear the status clobbered
one entry.
Add a feature tag for devices that are removable.
aic7xxx.reg:
Never use the sequencer interrupt value of 0xF0. We need
to guanrantee that an INTSTAT value of 0xFF can only occur
during card failure or a hot-eject.
Align the busy targets table with the begining of scratch
space. This seems to appease a chip bug in the aic7895.
aic7xxx.seq:
Be sure to disable select-out after a bus free event that occurs
early in a selection. If we don't disable select-out, we will
believe that it is enabled even though a new selection will never
occur.
Move the clearing of SELDI to just before a jump. This appeases
another chip bug of the aic7895.
Make the target mode command loop a bit more efficient.
AHC_SCB_BTT is a "flag" not a "feature". Check the right
field in the softc.
Properly cleanup the last SCB we tested against should we
fail to properly find an SCB for a reselection.
Add some additional sequencer debugging code.
aic7xxx_freebsd.c:
Limit the driver to 253 outstanding commands per adapter.
Guard against overflow in timeout handling.
aic7xxx_inline.h:
AHC_SCB_BTT is a "flag" not a "feature". Check the right
field in the softc.
aic7xxx_pci.c:
Set the removable feature for the apa1480 cardbus and the 29160C
Compact PCI card.
Don't report high byte termination information for narrow cards.
Use a PCI read rather than a questionable delay when fetching/setting
termination settings.
MFC'ed i due time. I can't test it under current right now because
netgraph seems to do unethical things with mutexes.
musycc:
Add status per channel.
Reduce printf chattyness
Keep error counters line if_mn does.
Increase descriptor count.
if_mn:
Support experimental unframed E1 lines.
These two drivers should share more code relating to framed channelized
TDM media in general (T1/E1/E3/T3, Sonet). Anyone interested email me.
interrupt threads to run with it always >= 1, so that malloc can
detect M_WAITOK from "interrupt" context. This is also necessary
in order to context switch from sched_ithd() directly.
Reviewed By: peter
parts: isa and pccard. The isa one is known to work with an IBM
EtherJet ISA card. The pccard one isn't known to work because the
EtherJet pccard I purchased recently arrived DOA :-(. I'll commit the
pccard.conf entry when the replacement card arrives.
I plan on MFC this in a week or two.
o 1.111 imp Sync with FreeBSD.
o 1.110 nonaka Add Roland SCP-55
o 1.109 ichiro add NANOSPEED ROOT-RZ2000 WLAN Card
o 1.108 ichiro add EMTAC A2424i 11Mbps WLAN Card
o 1.107 haya Add IO Data CBIDE2 ata interface card.
o 1.106 jhawk s/NULL}/NULL }/
o 1.105 thorpej " " -> "&sp" in two entries, per Rafal Boni.
o 1.104 thorpej Add SMC 2632W. From Rafal Boni, kern/11775.
o 1.103 drochner add IBM microdrive
o 1.102 soren Typo.
o 1.101 hubertf Add ELSA WaveLAN card & a noname clone(?)
o 1.100 toddpw Socket Comm. PC Card Ethernet, and tidy up naming.
o 1.99 msaitoh MELCO LPC2-TX, Telecom Device TCD-HPC100,
MACNICA ME1-JEIDA
o 1.98 imp Sort BAY into numerical order. (already in FreeBSD)
if_vr: handle the case where vr_encap() returns failure: bust out of the
packet sending loop instead of panicking. Also add some missing
newlines to some printf()s.
if_dc: The miibus_read and miibus_write methods keep swapping in and
out of MII mode by fiddling with CSR6 for cards with MII PHYs.
This is a hack to support the original Macronix 98713 card which
has built-in NWAY that uses an MII-like management interface
even though it uses serial transceivers. Conditionalize this
so that we only do this on 98713 chips, since it does bad things
to genuine tulip chips (and maybe other clones).
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
active memory maps. This removes the need to change the memory
map from common to attribute every time a packet is sent/received.
This increases performance and decreases cpu load (ping times on
slow machines improve by about 1.5ms).
Move out the old common memory/attrbiute memory hack functions to a
new header file to tidy up the main code. I want to keep them available
for a while.
(so we can see rapidly whether something was a fabric device but is
now gone).
Add a tag which says what role this adapter should take. It can take
on the value of None, Target, Initiator or Both. None is useful for
warm failover purposes. Remove the ISP_CFG_NOINIT silliness since
a role of "None" does this.
Add a isp_lastmbxcmd tag to store the opcode for the last mailbox
command used.
Module) and FBM (Fibre Buffer Modules). Also remember to clear the
semaphore registers. Tell the RISC processor to not halt on FPM
parity errors.
Throw out the ISP_CFG_NOINIT silliness and instead go to the use of
adapter 'roles' to see whether one completes initialization or not
(mostly for Fibre Channel). The ultimate intent, btw, of all of this
is to have a warm standby adapter for failover reasons. Because
we do roles now, setting of Target Capable Class 3 service parameters
in the ICB for the 2x00 cards reflects from role. Also, in isp_start,
if we're not supporting an initiator role, we bounce outgoing commands
with a Selection Timeout error. Also clean out the TOGGLE_TMODE
goop for FC- there is no toggling of target mode like there is
for parallel SCSI cards.
Do more cleanup with respect to using target ids 0..125 in F-port
topologies. Also keep track of things which *were* fabric devices
so that when you rescan the fabric you can notify the outer layers
when fabric devices go away.
Only force a LOGOUT for fabric devices if they're still logged in
(i.e., you cat their Port Database entry. Clean up the Get All Next
scanning.
Finally, use a new tag in the softc to store the opcode for the
last mailbox command used so we can report which opcode timed
out.
exactly the same functionality via a sysctl, making this feature
a run-time option.
The default is 1(ON), which means that /dev/random device will
NOT block at startup.
setting kern.random.sys.seeded to 0(OFF) will cause /dev/random
to block until the next reseed, at which stage the sysctl
will be changed back to 1(ON).
While I'm here, clean up the sysctls, and make them dynamic.
Reviewed by: des
Tested on Alpha by: obrien
not yet been caught), don't save the config with a null drive
name (which causes the drive to be renamed "plex" on the next
start), put in the text "*invalid*" instead.
This is damage control, not a fix.
Experienced by: peter
Break some long format strings so that they fit in style(9)-sized
lines.
Remove some "outdentation".
all of the hwvol members of struct snd_mixer live in a hwvol_* namespace.
- When changing the mixer device via the hwvol_mixer sysctl, reset the
muted state so that a mute operation on a new device won't try to
unmute the new device with the old device's saved volume.
- When the volume is muted, if a down or up volume request is received,
first restore the saved volume level and then adjust it.
Reviewed by: cg
cause the watchdog to (incorrectly) detect the interface state
going from down to up one second after lmc_ifup() was called,
causing lmc_ifup() to be called again, and resetting everything.
Fix by checking the interface state within lmc_ifup().
Submitted by: Darren Croke <djc@packetdesign.com>
Rewrite lockrange and unlockrange. The lock table is now a fixed
size, so there is no possibility for race conditions when expanding.
The current size (256 locked ranges) should be large enough that it
makes no sense to expand it. To do expansion right would require
quiescing the plex (requiring at least 256 I/O completions), and the
performance implications are horrendous.
Add a mutex per plex for accessing the lock table.
Based on analysis by: tegge
This should eliminate one case of foot shooting .
vinum_scandisk: If a drive in the partition table is downed, free it.
This duplicates code for the compatibility partition, which for some
reason was omitted here.
that require us to register our FC4 types of interest. Allow ourselves, in
F-port topologies, to start logging in fabric devices in the target 0..125
range. Change ISPASYNC_PDB_CHANGED (misnamed) to ISPASYNC_LOGGED_INOUT.
Fix (*SMACK*) again some default WWN stuff. This is *really* hard to get
right across all the range of platforms.
hscbs may be traded during error recovery due to the way
we manage the qinfifo. This has the effect of changing the
index to the sense buffer even though the request sense command
references the original buffer. SCBs don't play this swapping
game and so serve as a more consistent reference.
- add a dma hack similar to the NetBSD one
- change PDQ_OS_MEM{RD,WR} to use readl/writel rather than deref'ing
a 32 bit va.
Note that I did just enough to get this working on alpha. I probably
should have updated it to use busspace, but I was too lazy to navigate
the twisty minefield of ifdefs that make up this driver.
Tested by: wilko (on both x86 and alpha)
Add the entry for the Yano U640MO-03 MO drive. (ifdef-0-ed out for now)
Fix a hack were an original buffer was modified instead of copied
(cmd[] -> (*rcmd)[])
Submitted by: Iwasa Kazmi <kzmi@ca2.so-net.ne.jp>
instead of the requested length. Otherwise all transfers look like 0 byte
transfers to CAM.
Submitted by: Iwasa Kazmi <kzmi@ca2.so-net.ne.jp>
2) Finalise the command in the case of CBI transfers with CCI (command
completion interrupt).
3) Remove a redundant bzero of a buffer.
The pccard_function_init() call creates a bunch of inactive resources
that are persistant and configured on demand. When the child driver
"allocates" a resource it is connected up to one of these. When the
child releases the resource, we should not delete our copy, just
deactivate it again. Otherwise there is nothing to recreate it again
after several probe functions have run and done an alloc/release cycle.
INVARIANTS shows 0xdeadc0de without this.
More work is needed to do a sweep though the pccard_function_disable()
call to actually delete the resources for real. Right now, we leak
memory on eject (at best), so Dont Do That(TM) yet. This affects
16 bit pccards on a cardbus bridge only. This will be fixed soon, but
for now it gets the cards working.
Reviewed by: imp
to match the pccard.conf file. There are more ID's that need adding, but
these seem to be the common ones.
This was committed on an ep0 interface under NEWCARD:
ep0: <3Com 3c589 10Mbps Ethernet> at port 0x300-0x30f irq 9 function 0 config 1 on pccard1
ep0: Ethernet address 00:10:4b:df:48:57
Reviewed by: imp
to conform to style(9), plus one other convention that I use:
o Declare variables at the start of the function, rather than in blocks
when it doesn't help understanding (mine).
o 80 column limit.
o BSD style statement continuation, rather than "gnu" style.
bus to use. We need to set it here.
This fixes the problem where a probe routine establishes and
disestablishes the interrupt and then we get a panic in the probe
routine.
However, we pass the pointer to the interrupt hanlder count to the
parent bus, which writes its own cookie there, so there may be some
problems with that which isn't apparent at the moment.
Commit made from: laptop running NEWCARD with sn driver (which works,
but gets the wrong ethernet address).
o Fix OLDCARD to use the new interface.
o Rename the offsetp argument to deltap to more closely reflect what it
is returning (it returns the delta from the requested value to the actual
value).
o Remove duplicate $FreeBSD$ in pccbb.c
o Allow deltap to be NULL.
o Convert new isa pcic driver and add XXX comments that this function isn't
actually implemented there (which means that NEWCARD pccard stuff won't
work there until it is).
o Revert attempts to make old inferface work in NEWCARD.
Subitted by: peter (Parts of the new version code)
by even a compile of the OLDCARD code, was unapproved by me the keeper
of OLDCARD and broke OLDCARD and the ray driver.
Adjust new code to cope with the older interface.
If the interface changes in the future, it ***MUST*** be cleared by me
so that the OLDCARD impacts taken into account. It code in card_if.m
is used jointly by both OLDCARD and NEWCARD.
gets the cardbus code to compile, and I was successfully able to map
the CIS into high memory and probe/attach a 16 bit pccard.
Jonathan: feel free to replace this with your version if you want -
this is an expedient hack to get things to build and appear to work.
allocation not succeeding.
In this case, make sure the driver doesn't leak any memory by freeing all
necessary buffers; make sure to loop and free all the previously allocated
mbufs in this routine.
Reviewed by: alfred
- pccbb no longer needs to remember whether a card is inserted.
- pccbb reissues insertion on load of cardbus/pccard modules.
- got rid of unnecessary delays in power functions.
- Cardbus children are no longer deleted if probe/attach fails.
- non-attached child devices are reprobed at driver_added.
* CARD interface to read CIS
- added card_cis_read/card_cis_free interface to read arbitrary CIS
data. This currently is only implemented in cardbus.
* pccard begins to work
- pccard can now use higher memory space (and uses it by default).
- set_memory_offset interface changed.
- fixed ccr access, which was broken at multiple locations.
- implement an interrupt handler - pccard can now share interrupts.
- resource alloc/release/activate/deactivate functions gutted: some
resources are allocated by the bridge before the child device is
probed or attached. Thus the resource "belongs" to the bridge, and
the pccard_*_resource functions need to fudge the owner/rid.
- changed some error conditions to panics to speed debugging.
* Mutex fix - Giant is entered at the beginning of thread
This version is functional and is aproaching solid..
notice I said APROACHING. There are many node types I cannot test
I have tested: echo hole ppp socket vjc iface tee bpf async tty
The rest compile and "Look" right. More changes to follow.
DEBUGGING is enabled in this code to help if people have problems.
aic7xxx.h:
First pass at big-endian support in the Core.
Capture state for second channel on TWIN channel adapters
for suspend and resume.
aic7xxx_freebsd.h:
Stubs for endian conversion functions. These will get filled
out once we get an official kernel api for this kind of thing
that is something more elegant and efficient than a bunch of
manual swaps #ifdefed by platform.
aic7xxx_pci.c
Allow the second channel of motherboard aic7896 chips to be attached.
It turns out that the encoding of the subdevice id differs between
PCI cards and MB based controllers and our check to see, via
the subvendor id, if the second channel was "stuffed" always
turned out negative.
the video switch by another. Exactly as VESA does on top of VGA.
It adds linear framebuffer to S3 VESA 1.2 cards.
Obtained from: The original S3 ISA code comes from
Peter Horton <pdh@colonel-panic.com>
specific snd_mixer device rather than global across all mixers.
- Add per-mixer mute status and saved mute_level so that the mixer_hwmute()
function can now toggle the mute state when the mute button is pressed.
- Create a dynamic sysctl tree hw.snd.pcmX when a pcm device is registered.
- Move the hw.snd.hwvol_* sysctl's to hw.snd.pcmX.hwvol_* so that they
are now properly device-specific. Eventually when the mixers become
their own devices these sysctl's will move to live under a mixerX tree.
- Change the interface of the hwvol_mixer sysctl so that it reports the
name of the current mixer device instead of the number and is settable
with the name instead of the number.
- Add a new function mixer_hwinit() used to setup the dynamic sysctl's
needed for the hwvol support that can be called by drivers that support
hwvol.
Reviewed by: cg
'chancount' never got up to equaling 'maxchans'. As a result,
pcm_makelinks() was never called, and one always had to set the sysctl to
get the /dev/mixer and other symlinks generated in the DEVFS case. Instead,
change the test in pcm_addchan() to call pcm_makelinks() after the first
channel is initialized, since the aliases are linked to channel 0.
Reviewed by: cg
status register rather than 0. Without this, a single hardware volume
event triggers an interrupt storm.
- Implement hardware volume control for the Maestro chips. This version
only handles the case where both channels are adjusted at the same time.
Reviewed by: cg
- The mixer_hwmute() function can be called when a soundcard receives a
mute request.
- The mixer_hwstep() function can be used to adjust the volume of one or
both channels.
- The 'hw.snd.hwvol_step' sysctl determines the amount that mixer_hwstep()
adjusts the volume by on each call.
- The 'hw.snd.hwvol_mixer' sysctl specifies the mixer device to adjust the
volume on for both functions. The values used correspond to the
SOUNDCARD_MIXER_* constants.
want according to the modes set with the ppc(4) flags. Especially, it
should fix some problems with mode detection of parallel chipsets
configured to EPP but which have timing troubles with the drives. In such
a case, the driver should now fall back to slower modes (PS2, NIBBLE).
WWNs correctly (Again!) - this time for the case that we're not going
to fully init the adapter if isp_init is called (with ISP_CFG_NOINIT
set in options). The pupose for this is to bring the adapter up to
almost ready to go, get info out of NVRAM, but to not start it up- leaving
it until later to actually start things up if wanted (and possibly with
different roles selected).
with the driver locking up under load.
- Restructure so that we use a static pool of commands/FIBs, rather than
allocating them in clusters. The cluster allocation just made things
more complicated, and allowed us to waste more memory in peak load
situations.
- Make queueing macros more like my other drivers. This adds queue stats
for free. Add some debugging to take advantage of this.
- Reimplement the periodic timeout scan. Kick the interrupt handler
and the start routine every scan as well, just to be safe. Track busy
commands properly.
- Bring resource cleanup into line with resource allocation. We should
now clean up correctly after a failed probe/unload/etc.
- Try to start new commands when old ones are completed. We weren't doing
this before, which could lead to deadlock when the controller was full.
- Don't try to build a new command if we have found a deferred command.
This could cause us to lose the deferred command.
- Use diskerr() to report I/O errors.
- Don't bail if the AdapterInfo structure is the wrong size. Some variation
seems to be normal. We need to improve our handing of 2.x firmware sets.
- Improve some comments in an attempt to try to make things clearer.
- Restructure to avoid some warnings.
o Move the ax88190 code to its own function.
o Move all device_method_t, driver_t and DRIVER_MODULE definitions to the
end of files.
o Wrap a few lines > 80 characters.
o Use the same devclass for all ed drivers. This allows machines with
multiple types of cards to have their cards numbered correctly. Before,
you could wind up with two ed0's.
o Protect if_edvar.h from multiple includes because I was there.
modify chn_setblocksize() to pick a default soft-blocksize appropriate to the
sample rate and format in use. it will aim for a power of two size small
enough to generate block sizes of at most 20ms. it will also set the
hard-blocksize taking into account rate/format conversions in use.
update drivers to implement setblocksize correctly:
updated, tested: sb16, emu10k1, maestro, solo
updated, untested: ad1816, ess, mss, sb8, csa
not updated: ds1, es137x, fm801, neomagic, t4dwave, via82c686
i lack hardware to test: ad1816, csa, fm801, neomagic
others will be updated/tested in the next few days.
This is because calls with M_WAIT (now M_TRYWAIT) may not wait
forever when nothing is available for allocation, and may end up
returning NULL. Hopefully we now communicate more of the right thing
to developers and make it very clear that it's necessary to check whether
calls with M_(TRY)WAIT also resulted in a failed allocation.
M_TRYWAIT basically means "try harder, block if necessary, but don't
necessarily wait forever." The time spent blocking is tunable with
the kern.ipc.mbuf_wait sysctl.
M_WAIT is now deprecated but still defined for the next little while.
* Fix a typo in a comment in mbuf.h
* Fix some code that was actually passing the mbuf subsystem's M_WAIT to
malloc(). Made it pass M_WAITOK instead. If we were ever to redefine the
value of the M_WAIT flag, this could have became a big problem.
striped plexes.
Submitted by: des
Don't lock buffers before calls to sdio, sdio does it by itself.
Submitted by: tegge
parityops: Use correct casts when returning error information.
Requested by: Bernd Walter <ticso@cicely8.cicely.de>
Cor Bosman <cor@xs4all.net>
Kai Storbeck <kai@xs4all.net>
Joe Greco <jgreco@ns.sol.net>
Add support for Compaq SMART-2 RAID (idad) as storage
device for Vinum subdisks.
Reported by: Aaron Hill <hillaa@hotmail.com>
ahc_pci.c:
Add detach support.
Make use of soft allocated on our behalf by newbus.
For PCI devices, disable the mapping type we aren't
using for extra protection from rogue code.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Sync perforce IDs.
aic7xxx_freebsd.c:
Capture the eventhandle returned by EVENTHANDER_REGISTER
so we can kill the handler off during detach.
Use AHC_* constants instead of hard coded numbers in a
few more places.
Test PPR option state when deciding to "really" negotiate
when the CAM_NEGOTIATE flag is passed in a CCB.
Make use of core "ahc_pause_and_flushwork" routine in our
timeout handler rather than re-inventing this code.
Cleanup all of our resources (really!) in ahc_platform_free().
We should be all set to become a module now.
Implement the core ahc_detach() routine shared by all of
the FreeBSD front-ends.
aic7xxx_freebsd.h:
Softc storage for our event handler.
Null implementation for the ahc_platform_flushwork() OSM
callback. FreeBSD doesn't need this as XPT callbacks are
safe from all contexts and are done directly in ahc_done().
aic7xxx_inline.h:
Implement new lazy interrupt scheme. To avoid an extra
PCI bus read, we first check our completion queues to
see if any work has completed. If work is available, we
assume that this is the source of the interrupt and skip
reading INTSTAT. Any remaining interrupt status will be
cleared by a second call to the interrupt handler should
the interrupt line still be asserted. This drops the
interrupt handler down to a single PCI bus read in the
common case of I/O completion. This is the same overhead
as in the not so distant past, but the extra sanity of
perforning a PCI read after clearing the command complete
interrupt and before running the completion queue to avoid
missing command complete interrupts added a cycle.
aic7xxx.c:
During initialization, be sure to initialize all scratch
ram locations before they are read to avoid parity errors.
In this case, we use a new function, ahc_unbusy_tcl() to
initialize the scratch ram busy target table.
Replace instances of ahc_index_busy_tcl() used to unbusy
a tcl without looking at the old value with ahc_unbusy_tcl().
Modify ahc_sent_msg so that it can find single byte messages.
ahc_sent_msg is now used to determine if a transfer negotiation
attempt resulted in a bus free.
Be more careful in filtering out only the SCSI interrupts
of interest in ahc_handle_scsiint.
Rearrange interrupt clearing code to ensure that at least
one PCI transaction occurrs after hitting CLRSINT1 and
writting to CLRINT. CLRSINT1 writes take a bit to
take effect, and the re-arrangement provides sufficient
delay to ensure the write to CLRINT is effective. The
old code might report a spurious interrupt on some "fast"
chipsets.
export ahc-update_target_msg_request for use by OSM code.
If a target does not respond to our ATN request, clear
it once we move to a non-message phase. This avoids
sending a MSG_NOOP in some later message out phase.
Use max lun and max target constants instead of
hard-coded values.
Use softc storage built into our device_t under FreeBSD.
Fix a bug in ahc_free() that caused us to delete
resources that were not allocated.
Clean up any tstate/lstate info in ahc_free().
Clear the powerdown state in ahc_reset() so that
registers can be accessed.
Add a preliminary function for pausing the chip and
processing any posted work.
Add a preliminary suspend and resume functions.
aic7xxx.h:
Limit the number of supported luns to 64. We don't
support information unit transfers, so this is the
maximum that makes sense for these chips.
Add a new flag AHC_ALL_INTERRUPTS that forces the
processing of all interrupt state in a single invokation
of ahc_intr(). When the flag is not set, we use the
lazy interrupt handling scheme.
Add data structures to store controller state while
we are suspended.
Use constants instead of hard coded values where appropriate.
Correct some harmless "unsigned/signed" conflicts.
aic7xxx.seq:
Only perform the SCSIBUSL fix on ULTRA2 or newer controllers.
Older controllers seem to be confused by this.
In target mode, ignore PHASEMIS during data phases.
This bit seems to be flakey on U160 controllers acting
in target mode.
aic7xxx_pci.c:
Add support for the 29160C CPCI adapter.
Add definitions for subvendor ID information
available for devices with the "9005" vendor id.
We currently use this information to determine
if a multi-function device doesn't have the second
channel hooked up on a board.
Add rudimentary power mode code so we can put the
controller into the D0 state. In the future this
will be an OSM callback so that in FreeBSD we don't
duplicate functionality provided by the PCI code.
The powerstate code was added after I'd completed
my regression tests on this code.
Only capture "left over BIOS state" if the POWRDN
setting is not set in HCNTRL.
In target mode, don't bother sending incremental
CRC data.
This sould make the system power-off correctly where the howto had
more bits set than RB_POWEROFF, e.g. RB_NOSYNC.
Submitted by: Peter Pentchev <roam@orbitel.bg>
going to hurt sio(4) performance for the time being. As we get closer to
release and have more of the kernel unlocked we can come back to doing
arcane optimizations to workaround the limitations of the sio hardware.
claimed that their Intel NIC is comatose after a warm boot from Windoze.
This is most likely due to the card getting put in the D3 state. This
should bring it back to life.
PCI code. This saves each driver from having to grovel around looking
for the right registers to twiddle.
I should eventually convert the other PCI drivers to do this; for now,
these three are ones which I know need power state handling.
format version number. (userland programs should not need to be
recompiled when the netgraph kernel internal ABI is changed.
Also fix modules that don;t handle the fact that a caller may not supply
a return message pointer. (benign at the moment because the calling code
checks, but that will change)
require the addition of flag 0x80000 to their config line in
pccard.conf(5). This flag is not optional. These Linksys cards will
not be recognized without it.
Reviewed by: imp, iwasaki
this gives us several benefits, including:
* easier extensibility- new optional methods can be added to
ac97/mixer/channel classes without having to fixup every driver.
* forward compatibility for drivers, provided no new mandatory methods are
added.
aicasm is run on the build machine and therefore needs to be
compiled and linked against the headers and libraries (resp)
of the build machine. Since normally the default include
directories are search after any specified on the command
line, make sure we don't accidentally pick up machine
dependent headers from the kernel compile directory by
specifying /usr/include first.
This solves the (cross) build problem for ia64.
Approved by: gibbs
- Remove redundant header-type-specific support in the cardbus pcibus
clone. The bridges don't need this anymore.
- Use pcib_get_bus instead of the deprecated pci_get_secondarybus.
- Implement read/write ivar support for the pccbb, and teach it how
to report its secondary bus number. Save the subsidiary bus number
as well, although we don't use it yet.
- Break out the /dev/pci driver into a separate file.
- Kill the COMPAT_OLDPCI support.
- Make the EISA bridge attach a bit more like the old code; explicitly
check for the existence of eisa0/isa0 and only attach if they don't
already exist. Only make one bus_generic_attach() pass over the
bridge, once both busses are attached. Note that the stupid Intel
bridge's class is entirely unpredictable.
- Add prototypes and re-layout the core PCI modules in line with
current coding standards (not a major whitespace change, just moving
the module data to the top of the file).
- Remove redundant type-2 bridge support from the core PCI code; the
PCI-CardBus code does this itself internally. Remove the now
entirely redundant header-class-specific support, as well as the
secondary and subordinate bus number fields. These are bridge
attributes now.
- Add support for PCI Extended Capabilities.
- Add support for PCI Power Management. The interface currently
allows a driver to query and set the power state of a device.
- Add helper functions to allow drivers to enable/disable busmastering
and the decoding of I/O and memory ranges.
- Use PCI_SLOTMAX and PCI_FUNCMAX rather than magic numbers in some
places.
- Make the PCI-PCI bridge code a little more paranoid about valid
I/O and memory decodes.
- Add some more PCI register definitions for the command and status
registers. Correct another bogus definition for type-1 bridges.
