#ifdef MSDOSFS_LARGE to run-time checks to see if "-o large" was specified.
Test case provided by Oliver Fromme:
truncate -s 200G test.img
mdconfig -a -t vnode -f test.img -u 9
newfs_msdos -s 419430400 -n 1 /dev/md9 zip250
mount -t msdosfs /dev/md9 /mnt # should fail
mount -t msdosfs -o large /dev/md9 /mnt # should succeed
PR: 105964
Requested by: Oliver Fromme <olli lurza secnetix de>
Tested by: trhodes
MFC after: 2 weeks
These are shared-memory variants based on Am79C90-compatible chips
that apart from the missing DMA engine are similar to the 'ledma'
variant including using a (pseudo-)bus/device for the buffer that
the actual LANCE device hangs off from. The performance of these is
close to that of the 'ledma' one, like expected at a few times the
CPU load though.
the newly added DEV_EISA. This is done so that these back-ends can
be compiled on platforms not providing in{b,w,l}()/out{b,w,l}() and
friends (but may wish to use them together with bus front-ends other
than the EISA one).
bus hanging off from the Fireplane/Safari bus in some USIII machines.
This is part 3/4 of allowing creator(4) to work in these machines.
The little info needed on how to configure the bridge and to work
around the incorrect values contained in the `interrupts' properties
of its children were obtained form OpenSolaris.
The separate bus front-end was inherited from the OpenBSD creator(4),
which at that time had a mainbus(4) (for USI/II machines, which use
an UPA interconnection bus as the nexus) and an upa(4) (for USIII
machines, which use a subordinate/slave UPA bus hanging off from the
Fireplane/Safari interconnection bus) front-end. With FreeBSD and
newbus there is/will be no need to have two separate bus front-ends
for these busses, so we can easily coallapse the shared front-end
and the back-end into a single source file (note that the FreeBSD
creator_upa.c was misnomer anyway; based on what it actually attached
to that should have been creator_nexus.c), actually OpenBSD meanwhile
also has moved to a shared front-end and a single source file. Due
to the low-level console support creator.c also wasn't free from bus
related things before.
While at it, also split sys/sparc64/creator/creator.h into a
sys/dev/fb/creatorreg.h that only contains register macros and move
the structures to the top of sys/dev/fb/creator.c as suggested by
style(9) so creator(4) is no longer scattered over two directories.
- Use OF_decode_addr()/sparc64_fake_bustag() to obtain the bus tags and
handles for the low-level console support instead of hardcoding
support for AFB/FFB hanging off from nexus(4) only. This is part 2/4
of allowing creator(4) to work in USIII machines (which have a UPA
bus hanging off from the Fireplane/Safari bus reflected by the nexus),
which already makes it work as the low-level console there.
- Allocate resources in the bus attach routine regardless of whether
creator(4) is used as for the low-level console and thus the required
bus tags and handles have been already obtained or not so the resources
are marked as taken in the respective RMAN.
- For both obtaining the bus tags and handles for the low-level console
support as well as allocating the corresponding resources in the
regular bus attach routine don't bother to get all for the maximum of
24 register banks but only (for) the two tag/handle pairs required for
providing the video interface for syscons(4) support. If we can't
allocate the rest of them just limit the memory range accessible via
creator_fb_mmap() accordingly.
- Sanity check the memory range spanned by the first and last resources
and the resources in between as far as possible, as the XFree86/Xorg
sunffb(4) expects to be able to access the whole region, even though
the backing resources are actually non-continuous. Limit and check
the memory range accessible via creator_fb_mmap() accordingly.
- Reduce the size of buffers for OFW properties to what they actually
need to hold.
- Rename some tables to creator_<foo> for consistency.
- Also for the sizes in the creator_fb_mmap() mapping table entries use
macros for consistency, add macros for the remaining register banks
for completeness.
NOTES though, as ofw_syscons(4) doesn't properly interface with
syscons(4) regarding loading the font specified with SC_DFLT_FONT,
causing a kernel with both options SC_OFWFB and SC_NO_MODE_CHANGE
to not link.
lookup early. This has some performance implications and should not be
enabled by default, but might help greatly in certain setups. After some
more testing this could be turned into a sysctl.
Tested by: avatar
LOR ids: 17, 24, 32, 46, 191 (conceptual)
MFC after: 6 weeks
mac_framework.c Contains basic MAC Framework functions, policy
registration, sysinits, etc.
mac_syscalls.c Contains implementations of various MAC system calls,
including ENOSYS stubs when compiling without options
MAC.
Obtained from: TrustedBSD Project
aches as a read-only file. In a number of cases this has led to
compiles failing- usually due to some strange NFS drift which thinks
that the opt_ah.h in the compile directory is out of date wrt the
source it is copied from. When the copy is executed again, it fails
because the target is read-only. Oops. Modify the compile hooks
avoid this.
Discussed with a while back with: Sam Leffler
just the intenral phy on parts supported by the rl and re drivers, the
RTL8201BL for example. He also sent me a nice picture of hundreds of
these chips in a tray to boulder his claim. :-) Therefore remove a
comment that suggested that they were...
by default for sun4v where it is absolutely required.
This change moves the buffer from struct pcpu to the stack to avoid
using the critical section which created a LOR in a couple of cases
due to interaction with the tty code and kqueue. The LOR can't be
fixed with the critical section and the pcpu buffer can't be used
without the critical section.
Putting the buffer on the stack was my initial solution, but it was
pointed out that the stress on the stack might cause problems
depending on the call path. We don't have a way of creating tests
for those possible cases, so it's best to leave this as an option
for the time being. In time we may get enough data to enable this
option more generally.
way I intended due to licensing restrictions. I had intended
that it would be defaulted on, with opt-out possible for
companies that don't accept the CDDL. The FreeBSD GENERIC
kernel has to be entirely BSD licensed, so the only alternative
would have been to make KDTRACE an opt-in option. That isn't
a design I favour.
- Add a new apic_alloc_vectors() method to the local APIC support code
to allocate N contiguous IDT vectors (aligned on a M >= N boundary).
This function is used to allocate IDT vectors for a group of MSI
messages.
- Add MSI and MSI-X PICs. The PIC code here provides methods to manage
edge-triggered MSI messages as x86 interrupt sources. In addition to
the PIC methods, msi.c also includes methods to allocate and release
MSI and MSI-X messages. For x86, we allow for up to 128 different
MSI IRQs starting at IRQ 256 (IRQs 0-15 are reserved for ISA IRQs,
16-254 for APIC PCI IRQs, and IRQ 255 is reserved).
- Add pcib_(alloc|release)_msi[x]() methods to the MD x86 PCI bridge
drivers to bubble the request up to the nexus driver.
- Add pcib_(alloc|release)_msi[x]() methods to the x86 nexus drivers that
ask the MSI PIC code to allocate resources and IDT vectors.
MFC after: 2 months
wait (time waited to acquire) and hold times for *all* kernel locks. If
the architecture has a system synchronized TSC, the profiling code will
use that - thereby minimizing profiling overhead. Large chunks of profiling
code have been moved out of line, the overhead measured on the T1 for when
it is compiled in but not enabled is < 1%.
Approved by: scottl (standing in for mentor rwatson)
Reviewed by: des and jhb
privilege for threads and credentials. Unlike the existing suser(9)
interface, priv(9) exposes a named privilege identifier to the privilege
checking code, allowing more complex policies regarding the granting of
privilege to be expressed. Two interfaces are provided, replacing the
existing suser(9) interface:
suser(td) -> priv_check(td, priv)
suser_cred(cred, flags) -> priv_check_cred(cred, priv, flags)
A comprehensive list of currently available kernel privileges may be
found in priv.h. New privileges are easily added as required, but the
comments on adding privileges found in priv.h and priv(9) should be read
before doing so.
The new privilege interface exposed sufficient information to the
privilege checking routine that it will now be possible for jail to
determine whether a particular privilege is granted in the check routine,
rather than relying on hints from the calling context via the
SUSER_ALLOWJAIL flag. For now, the flag is maintained, but a new jail
check function, prison_priv_check(), is exposed from kern_jail.c and used
by the privilege check routine to determine if the privilege is permitted
in jail. As a result, a centralized list of privileges permitted in jail
is now present in kern_jail.c.
The MAC Framework is now also able to instrument privilege checks, both
to deny privileges otherwise granted (mac_priv_check()), and to grant
privileges otherwise denied (mac_priv_grant()), permitting MAC Policy
modules to implement privilege models, as well as control a much broader
range of system behavior in order to constrain processes running with
root privilege.
The suser() and suser_cred() functions remain implemented, now in terms
of priv_check() and the PRIV_ROOT privilege, for use during the transition
and possibly continuing use by third party kernel modules that have not
been updated. The PRIV_DRIVER privilege exists to allow device drivers to
check privilege without adopting a more specific privilege identifier.
This change does not modify the actual security policy, rather, it
modifies the interface for privilege checks so changes to the security
policy become more feasible.
Sponsored by: nCircle Network Security, Inc.
Obtained from: TrustedBSD Project
Discussed on: arch@
Reviewed (at least in part) by: mlaier, jmg, pjd, bde, ceri,
Alex Lyashkov <umka at sevcity dot net>,
Skip Ford <skip dot ford at verizon dot net>,
Antoine Brodin <antoine dot brodin at laposte dot net>
work is not just mine, but it is also the works of Peter Lei
and Michael Tuexen. They both are my two key other developers
working on the project.. and they need ata-boy's too:
****
peterlei@cisco.comtuexen@fh-muenster.de
****
I did do a make sysent which updated the
syscall's and sysproto.. I hope that is correct... without
it you don't build since we have new syscalls for SCTP :-0
So go out and look at the NOTES, add
option SCTP (make sure inet and inet6 are present too)
and play with SCTP.
I will see about comitting some test tools I have after I
figure out where I should place them. I also have a
lib (libsctp.a) that adds some of the missing socketapi
functions that I need to put into lib's.. I will talk
to George about this :-)
There may still be some 64 bit issues in here, none of
us have a 64 bit processor to test with yet.. Michael
may have a MAC but thats another beast too..
If you have a mac and want to use SCTP contact Michael
he maintains a web site with a loadable module with
this code :-)
Reviewed by: gnn
Approved by: gnn
as we have no use for that info. Instead let this function return the
keyboard ID and verify at its invocation in sunkbd_configure() that we're
talking to a Sun type 4/5/6 keyboard, i.e. a keyboard supported by this
driver.
- Add an option SUNKBD_EMULATE_ATKBD whose code is based on the respective
code in ukbd(4) and like UKBD_EMULATE_ATSCANCODE causes this driver to
emit AT keyboard/KB_101 compatible scan codes in K_RAW mode as assumed by
kbdmux(4). Unlike UKBD_EMULATE_ATSCANCODE, SUNKBD_EMULATE_ATKBD also
triggers the use of AT keyboard maps and thus allows to use the map files
in share/syscons/keymaps with this driver at the cost of an additional
translation (in ukbd(4) this just is the way of operation).
- Implement an option SUNKBD_DFLT_KEYMAP, which like the equivalent options
of the other keyboard drivers allows to specify the default in-kernel
keyboard map. For obvious reasons this made to only work when also using
SUNKBD_EMULATE_ATKBD.
- Implement sunkbd_check(), sunkbd_check_char() and sunkbd_clear_state(),
which are also required for interoperability with kbdmux(4).
- Implement K_CODE mode and FreeBSD keypad compose.
- As a minor hack define KBD_DFLT_KEYMAP also in the !SUNKBD_EMULATE_ATKBD
case so we can obtain fkey_tab from <dev/kbd/kbdtables.h> rather than
having to duplicate it and #ifdef some more code.
- Don't use the TX-buffer for writing the two command bytes for setting the
keyboard LEDs as this consequently requires a hardware FIFO that is at
least two bytes in depth, which the NMOS-variant of the Zilog SCCs doesn't
have. Thus use an inlined version of uart_putc() to consecutively write
the command bytes (a cleaner approach would be to do this via the soft
interrupt handler but that variant wouldn't work while in ddb(4)). [1]
- Fix some minor style(9) bugs.
PR: 90316 [1]
Reviewed by: marcel [1]
dynamic nature (if no native aio code is available, the linux part
returns ENOSYS because of missing requisites) should be solved differently
than it is.
All this will be done in P4.
Not included in this commit is a backout of the changes to the native aio
code (removing static in some places). Those changes (and some more) will
also be needed when the reworked linux aio stuff will reenter the tree.
Requested by: rwatson
Discussed with: rwatson
i386). Use -mprofiler-epilogue again, and don't use -finstrument-functions.
The former has been fixed for arches that implement high-res profiling,
and the latter has been useless for kernel profiling since gcc-3.4
when it started forcing -fno-inline. -fno-inline gives a kernel with
performance characteristics too different from a normal kernel to be
worth profiling, by turning off inlining of all the little optimized
functions in headers. This interacts especially badly with FreeBSD's
use of "static inline" for all inlines in headers, by creating many
separate copies of the little functions, so not inlining tends to
increase cache pressure where it should reduce it, and (since gprof(1)
doesn't understand the copies) the statistics for the little functions
are hard to interpret even if you want them.
to and from struct timespec, to replace the crummy conversion
function which have been copy&pasted into three different
filesystems already.
Apart from general crummyness as indicated by code like:
for (year = 1970;; year++) {
inc = year & 0x03 ? 365 : 366;
if (days < inc)
break;
days -= inc;
}
They also contain specialized crummyness which tries to compensate
for the general crummyness by caching recent conversion results,
with no regard for locking or consistency.
These replacement functions are smaller, O(1) and handle the Y2.1K
leap-year correctly.
Ideally, these functions should live in a module of their own,
which the three offending filesystems would depend on, but the
size is 877 bytes of code (on i386), so that would be false
economy.
should be easily adapted to SD 2.0 (aka SDHC), SDIO, MMC and MMCplus
cards. At the present time, there's only one bridge driver for the
ARM9 based Atmel AT91RM9200.
snd_emu10k1 and snd_emu10kx into one line. The 'pci' dependency here
adds no value, so I eliminted it (we don't have a snd.all file that
might make it mildly useful, and even then it wouldn't be that
useful). With the pci optional component eliminated, I could use the
'|' operator. I could have also include pci on both sides of the |
operator, but since it isn't a value add at all, it was better to
eliminate it.
Implement the linux_io_* syscalls (AIO). They are only enabled if the native
AIO code is available (either compiled in to the kernel or as a module) at
the time the functions are used. If the AIO stuff is not available there
will be a ENOSYS.
From the submitter:
---snip---
DESIGN NOTES:
1. Linux permits a process to own multiple AIO queues (distinguished by
"context"), but FreeBSD creates only one single AIO queue per process.
My code maintains a request queue (STAILQ of queue(3)) per "context",
and throws all AIO requests of all contexts owned by a process into
the single FreeBSD per-process AIO queue.
When the process calls io_destroy(2), io_getevents(2), io_submit(2) and
io_cancel(2), my code can pick out requests owned by the specified context
from the single FreeBSD per-process AIO queue according to the per-context
request queues maintained by my code.
2. The request queue maintained by my code stores contrast information between
Linux IO control blocks (struct linux_iocb) and FreeBSD IO control blocks
(struct aiocb). FreeBSD IO control block actually exists in userland memory
space, required by FreeBSD native aio_XXXXXX(2).
3. It is quite troubling that the function io_getevents() of libaio-0.3.105
needs to use Linux-specific "struct aio_ring", which is a partial mirror
of context in user space. I would rather take the address of context in
kernel as the context ID, but the io_getevents() of libaio forces me to
take the address of the "ring" in user space as the context ID.
To my surprise, one comment line in the file "io_getevents.c" of
libaio-0.3.105 reads:
Ben will hate me for this
REFERENCE:
1. Linux kernel source code: http://www.kernel.org/pub/linux/kernel/v2.6/
(include/linux/aio_abi.h, fs/aio.c)
2. Linux manual pages: http://www.kernel.org/pub/linux/docs/manpages/
(io_setup(2), io_destroy(2), io_getevents(2), io_submit(2), io_cancel(2))
3. Linux Scalability Effort: http://lse.sourceforge.net/io/aio.html
The design notes: http://lse.sourceforge.net/io/aionotes.txt
4. The package libaio, both source and binary:
http://rpmfind.net/linux/rpm2html/search.php?query=libaio
Simple transparent interface to Linux AIO system calls.
5. Libaio-oracle: http://oss.oracle.com/projects/libaio-oracle/
POSIX AIO implementation based on Linux AIO system calls (depending on
libaio).
---snip---
Submitted by: Li, Xiao <intron@intron.ac>
unsuspecting users.
- Add a comment in NOTES about experimental status of SCHED_ULE.
- Make warning about experimental status in sched_ule(4) a bit
stronger.
Suggested and reviewed by: dougb
Discussed on: developers
MFC after: 3 days
Split subr_clock.c in two parts (by repo-copy):
subr_clock.c contains generic RTC and calendaric stuff. etc.
subr_rtc.c contains the newbus'ified RTC interface.
Centralize the machdep.{adjkerntz,disable_rtc_set,wall_cmos_clock}
sysctls and associated variables into subr_clock.c. They are
not machine dependent and we have generic code that relies on being
present so they are not even optional.
Add support for Intel High Definition Audio Controller.
This driver make a special guarantee that "playback" works
on majority hardwares with minimal or without specific vendor
quirk.
This driver is a product of collaborative effort made by:
Stephane E. Potvin <sepotvin@videotron.ca>
Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Wesley Morgan <morganw@chemikals.org>
Daniel Eischen <deischen@FreeBSD.org>
Maxime Guillaud <bsd-ports@mguillaud.net>
Ariff Abdullah <ariff@FreeBSD.org>
....and various people from freebsd-multimedia@FreeBSD.org
Refer to snd_hda(4) for features and issues.
Welcome To HDA.
Sponsored by: Defenxis Sdn. Bhd.
With the first part of my previous Summer of Code work, we get:
-made libalias modular:
-support for 'particular' protocols (like ftp/irc/etcetc) is no more
hardcoded inside libalias, but it's available through external
modules loadable at runtime
-modules are available both in kernel (/boot/kernel/alias_*.ko) and
user land (/lib/libalias_*)
-protocols/applications modularized are: cuseeme, ftp, irc, nbt, pptp,
skinny and smedia
-added logging support for kernel side
-cleanup
After a buildworld, do a 'mergemaster -i' to install the file libalias.conf
in /etc or manually copy it.
During startup (and after every HUP signal) user land applications running
the new libalias will try to read a file in /etc called libalias.conf:
that file contains the list of modules to load.
User land applications affected by this commit are ppp and natd:
if libalias.conf is present in /etc you won't notice any difference.
The only kernel land bit affected by this commit is ng_nat:
if you are using ng_nat, and it doesn't correctly handle
ftp/irc/etcetc sessions anymore, remember to kldload
the correspondent module (i.e. kldload alias_ftp).
General information and details about the inner working are available
in the libalias man page under the section 'MODULAR ARCHITECTURE
(AND ipfw(4) SUPPORT)'.
NOTA BENE: this commit affects _ONLY_ libalias, ipfw in-kernel nat
support will be part of the next libalias-related commit.
Approved by: glebius
Reviewed by: glebius, ru
- Split out the communication protocols into their own files and use
a couple of function pointers in the softc that the commuication
protocols setup in their own attach routine.
- Add support for the SSIF interface (talking to IPMI over SMBus).
- Add an ACPI attachment.
- Add a PCI attachment that attaches to devices with the IPMI interface
subclass.
- Split the ISA attachment out into its own file: ipmi_isa.c.
- Change the code to probe the SMBIOS table for an IPMI entry to just use
pmap_mapbios() to map the table in rather than trying to setup a fake
resource on an isa device and then activating the resource to map in the
table.
- Make bus attachments leaner by adding attach functions for each
communication interface (ipmi_kcs_attach(), ipmi_smic_attach(), etc.)
that setup per-interface data.
- Formalize the model used by the driver to handle requests by adding an
explicit struct ipmi_request object that holds the state of a given
request and reply for the entire lifetime of the request. By bundling
the request into an object, it is easier to add retry logic to the various
communication backends (as well as eventually support BT mode which uses
a slightly different message format than KCS, SMIC, and SSIF).
- Add a per-softc lock and remove D_NEEDGIANT as the driver is now MPSAFE.
- Add 32-bit compatibility ioctl shims so you can use a 32-bit ipmitool
on FreeBSD/amd64.
- Add ipmi(4) to i386 and amd64 NOTES.
Submitted by: ambrisko (large portions of 2 and 3)
Sponsored by: IronPort Systems, Yahoo!
MFC after: 6 days
other problems while labels were first being added to various kernel
objects. They have outlived their usefulness.
MFC after: 1 month
Suggested by: Christopher dot Vance at SPARTA dot com
Obtained from: TrustedBSD Project
part of the hal distribution early on when the hal was built for
each os but it's been portable for a long time so move the os-specific
code out (and off the vendor branch)
o correct the copyright on ah_osdep.?; it was mistakenly given a
restricted license and not a dual-bsd/gpl license
o remove the module api definition as it was never used
o fixup include paths for move of ah_osdep.h
MFC after: 2 weeks
in older versions of FreeBSD. This option is pointless as it is needed in just
about every interesting usage of forward that I have ever seen. It doesn't make
the system any safer and just wastes huge amounts of develper time
when the system doesn't behave as expected when code is moved from
4.x to 6.x It doesn't make
the system any safer and just wastes huge amounts of develper time
when the system doesn't behave as expected when code is moved from
4.x to 6.x or 7.x
Reviewed by: glebius
MFC after: 1 week
- TLS - complete
- pid/tid mangling - complete
- thread area - complete
- futexes - complete with issues
- clone() extension - complete with some possible minor issues
- mq*/timer*/clock* stuff - complete but untested and the mq* stuff is
disabled when not build as part of the kernel with native FreeBSD mq*
support (module support for this will come later)
Tested with:
- linux-firefox - works, tested
- linux-opera - works, tested
- linux-realplay - doesnt work, issue with futexes
- linux-skype - doesnt work, issue with futexes
- linux-rt2-demo - works, tested
- linux-acroread - doesnt work, unknown reason (coredump) and sometimes
issue with futexes
- various unix utilities in linux-base-gentoo3 and linux-base-fc4:
everything tried worked
On amd64 not everything is supported like on i386, the catchup is planned for
later when the remaining bugs in the new functions are fixed.
To test this new stuff, you have to run
sysctl compat.linux.osrelease=2.6.16
to switch back use
sysctl compat.linux.osrelease=2.4.2
Don't switch while running a linux program, strange things may or may not
happen.
Sponsored by: Google SoC 2006
Submitted by: rdivacky
Some suggestions/help by: jhb, kib, manu@NetBSD.org, netchild
serial line usb drivers that depend on it. Instead, let the compile
fail rather than silently not including the driver. This is more in
line with how we handle things like mii.
# I'll note: a better system for coping with missing depends is needed,
# but this dependency is clearly backwards given our current flawed
# depend system.
whole the physical memory, cached, using 1MB section mappings. This reduces
the address space available for user processes a bit, but given the amount of
memory a typical arm machine has, it is not (yet) a big issue.
It then provides a uma_small_alloc() that works as it does for architectures
which have a direct mapping.
uipc_proto.c to uipc_usrreq.c, making localdomain static. Remove
uipc_proto.c as it's no longer used. With this change, UNIX domain
sockets are entirely encapsulated in uipc_usrreq.c.
PowerPC-based Apple's machines and small utility to do it from
userland modelled after the similar utility in Darwin/OSX.
Only tested on 1.25GHz G4 Mac Mini.
MFC after: 1 month
and pc98 MD files. Remove nodevice and nooption lines specific
to sio(4) from ia64, powerpc and sparc64 NOTES. There were no
such lines for arm yet.
sio(4) is usable on less than half the platforms, not counting
a future mips platform. Its presence in MI files is therefore
increasingly becoming a burden.
implementations and adjust some of the checks while I'm here:
- Add a new check to make sure we don't return from a syscall in a critical
section.
- Add a new explicit check before userret() to make sure we don't return
with any locks held. The advantage here is that we can include the
syscall number and name in syscall() whereas that info is not available
in userret().
- Drop the mtx_assert()'s of sched_lock and Giant. They are replaced by
the more general checks just added.
MFC after: 2 weeks
new VIA CPUs.
For older CPUs HMAC/SHA1 and HMAC/SHA256 (and others) will still be done
in software.
Move symmetric cryptography (currently only AES-CBC 128/192/256) to
padlock_cipher.c file. Move HMAC cryptography to padlock_hash.c file.
Hardware from: Centaur Technologies
the sysctls. This saves a lot of space in the resulting kernel which is
important for embedded systems. This change was done in a ABI compatible
way. The pointer is still there, it just points to an empty string instead
of the description.
MFC After: 3 days
subr_acl_posix1e.c, leaving kern_acl.c containing only ACL system
calls and utility routines common across ACL types.
Add subr_acl_posix1e.c to the build.
Obtained from: TrustedBSD Project
This driver was ported from OpenBSD by Shigeaki Tagashira
<shigeaki@se.hiroshima-u.ac.jp> and posted at
http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html
It was additionally cleaned up by me.
It is still a work-in-progress and thus is purposefully not in GENERIC.
And it conflicts with nve(4), so only one should be loaded.
encryption. There are two functions, a bpf tap which has a basic header with
the SPI number which our current tcpdump knows how to display, and handoff to
pfil(9) for packet filtering.
Obtained from: OpenBSD
Based on: kern/94829
No objections: arch, net
MFC after: 1 month
in 1999, and there are changes to the sysctl names compared to PR,
according to that discussion. The description is in sys/conf/NOTES.
Lines in the GENERIC files are added in commented-out form.
I'll attach the test script I've used to PR.
PR: kern/14584
Submitted by: babkin
for those upgrading from 4.x -> 5.x. It is therefore no longer
necessary because it is installed on 5.x and 6.x and one has to
upgrade from 6.x -> current, or at the very least 5.x (although not
supported, it can be made to work).
I picked it up again. The scheduler is forked from ULE, but the
algorithm to detect an interactive process is almost completely
different with ULE, it comes from Linux paper "Understanding the
Linux 2.6.8.1 CPU Scheduler", although I still use same word
"score" as a priority boost in ULE scheduler.
Briefly, the scheduler has following characteristic:
1. Timesharing process's nice value is seriously respected,
timeslice and interaction detecting algorithm are based
on nice value.
2. per-cpu scheduling queue and load balancing.
3. O(1) scheduling.
4. Some cpu affinity code in wakeup path.
5. Support POSIX SCHED_FIFO and SCHED_RR.
Unlike scheduler 4BSD and ULE which using fuzzy RQ_PPQ, the scheduler
uses 256 priority queues. Unlike ULE which using pull and push, the
scheduelr uses pull method, the main reason is to let relative idle
cpu do the work, but current the whole scheduler is protected by the
big sched_lock, so the benefit is not visible, it really can be worse
than nothing because all other cpu are locked out when we are doing
balancing work, which the 4BSD scheduelr does not have this problem.
The scheduler does not support hyperthreading very well, in fact,
the scheduler does not make the difference between physical CPU and
logical CPU, this should be improved in feature. The scheduler has
priority inversion problem on MP machine, it is not good for
realtime scheduling, it can cause realtime process starving.
As a result, it seems the MySQL super-smack runs better on my
Pentium-D machine when using libthr, despite on UP or SMP kernel.
- Try hard to calculate a safe sp, so that the stack doesn't get smashed
while uncompressing or relocating the kernel.
- Bring in code needed to calculate the cacheline size etc, needed for
arm9_idcache_wbinv_all.
for CBUS-PNP cards there) by default, as there are no amd64 and sparc64
machines with ISA slots and which therefore could make use of this code
known to exist. For sparc64 this additionally allows to get rid of the
compat shims for in{b,w,l}()/out{b,w,l}() etc and the associated hacks.
OK'ed by: imp, peter
the arm to compile without all the extras that don't appear, at least
not in the flavors of ARM I deal with. This helps us save about 100k.
If I've botched the available devices on a platform, please let me
know and I'll correct ASAP.
`-Wundef'
Warn whenever an identifier which is not a macro is encountered in
an `#if' directive, outside of `defined'. Such identifiers are
replaced with zero.
but large parts are rewritten by matk and tanimura.
This is old code, it's not maintained since 2003. We also don't have a
maintainer for this! Yuriy Tsibizov took it and uses it in his emu10kx
driver. Since the emu10kx driver will enter the tree "soon" (some bugs
have to be fixed after Yuriy return from his holidays), I add it here
already.
This also contains some changes to emu10k1 and cmi, so if you're lucky,
you can now make some kind of use of midi with those soundcards.
To all those poor souls which don't have such a card: feel free to send
patches, we don't have a maintainer for this.
To those which miss a specific feature in the midi code: feel free to
submit patches, we don't have a maintainer for this.
Oh, did I already told that it would be nice if someone would take care
of it? Maintainer with midi equipment wanted! :-)
If you get LOR's, submit a PR and notify multimedia@ please. If you get
panics, submit a PR with a backtrace (compile the sound system into your
kernel instead of using modules in this case) and notify multimedia@
please.
Written by: matk, tanimura
Submitted by: "Yuriy Tsibizov" <Yuriy.Tsibizov@gfk.ru>
Based upon: code from NetBSD
- Linux ioctl support, with the other Linux changes MegaCli
will run if you mount linprocfs & linsysfs then set
sysctl compat.linux.osrelease=2.6.12 or similar. This works
on i386. It should work on amd64 but not well tested yet.
StoreLib may or may not work. Remember to kldload mfi_linux.
- Add in AEN (Async Event Notification) support so we can
get messages from the firmware when something happens.
Not all messages are in defined in event detail. Use
event_log to try to figure out what happened.
- Try to implement something like SIGIO for StoreLib. Since
mrmonitor doesn't work right I can't fully test it. StoreLib
works best with the rh9 base. In theory mrmonitor isn't
needed due to native driver support of AEN :-)
Now we can configure and monitor the RAID better.
Submitted by: IronPort Systems.
lnc(4) on PC98 and i386. The ISA front-end supports the same non-PNP
network cards as lnc(4) did and additionally a couple of PNP ones.
Like lnc(4), the C-bus front-end of le(4) only supports C-NET(98)S
and is untested due to lack of such hardware, but given that's it's
based on the respective lnc(4) and not too different from the ISA
front-end it should be highly likely to work.
- Remove the descriptions of le(4), which where converted from lnc(4),
from sys/i386/conf/NOTES and sys/pc98/conf/NOTES as there's a common
one in sys/conf/NOTES.
Add a new option, SKYEYE_WORKAROUNDS, which as the name suggests adds
workarounds for things skyeye doesn't simulate. Specifically :
- Use USART0 instead of DBGU as the console, make it not use DMA, and manually provoke an interrupt when we're done in the transmit function.
- Skyeye maintains an internal counter for clock, but apparently there's
no way to access it, so hack the timecounter code to return a value which
is increased at every clock interrupts. This is gross, but I didn't find a
better way to implement timecounters without hacking Skyeye to get the
counter value.
- Force the write-back of PTEs once we're done writing them, even if they
are supposed to be write-through. I don't know why I have to do that.
When porting FreeBSD to a new platform, one of the more useful things to do is
get mi_startup() to let you know which SYSINIT it's up to. Most people tend to
whack a printf in the SYSINIT loop to print the address of the function it's
about to call. Going one better, jhb made a version that uses DDB to look up
the name of the function and print that instead. This version is essentially
his with the addition of some ifdeffery to make it optional and to allow it to
work (although using only the function address, not the symbol) if you forgot
to enable DDB.
All the cool bits by: jhb
Approved by: scottl, rink, cognet, imp
the linux module, since it is not cross-platform
- move linprocfs from "files" and "options" to architecture specific files,
since it only makes sense to build this for those architectures, where we
also have a linuxolator
- disable the build of the linuxolator on our tier-2 architecture "Alpha":
* we don't have a linux_base port which supports Alpha and at the
same time is not outdated/obsoleted upstream/in a good condition/
currently working
* the upcomming new default linux base port is based upon Fedora
Core 3 (security support via http://www.fedoralegacy.org), which
isn't available for Alpha (like the current default linux base
port which is based upon Red Hat 8)
* nobody answered my request for testing it ~1 month ago on
current@ and alpha@ (it doesn't surprises me, see above)
* a SoC student wouldn't have to waste time on something which
nobody is willing to test
This does not remove the alpha specific MD files of the linuxolator yet.
Discussed on: arch (mostly silence)
Spiritual support by: scottl
o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
This driver was generously developed and donated by Highpoint.
It is enabled for i386 only at the moment. I will enable it for amd64
shortly.
Obtained from: HighPoint Technologies, Inc.
This allows one to change the behavior of the driver pre-boot.
NOTE: This patch was made for DragonFly BSD by Sepherosa Ziehau.
PR: kern/94833
Submitted by: Devon H. O'Dell
Obtained from: DragonFly
MFC after: 1 month
end for isa(4).
o Add a seperate bus frontend for acpi(4) and allow ISA DMA for
it when ISA is configured in the kernel. This allows acpi(4)
attachments in non-ISA configurations, as is possible for ia64.
o Add a seperate bus frontend for pci(4) and detect known single
port parallel cards.
o Merge PC98 specific changes under pc98/cbus into the MI driver.
The changes are minor enough for conditional compilation and
in this form invites better abstraction.
o Have ppc(4) usabled on all platforms, now that ISA specifics
are untangled enough.
Major differences:
* since there is no direct map region, there is no custom uma memory
allocator to modify to include its pages in the dumps.
* Various data entries are reduced from 64 bit to 32 bit to match the
native size.
dump_add_page() and dump_drop_page() are still present in case one wants to
arrange for arbitary pages to be dumped. This is of marginal use though
because libkvm+kgdb cannot address physical memory that isn't mapped into
kvm.
via the debug.minidump sysctl and tunable.
Traditional dumps store all physical memory. This was once a good thing
when machines had a maximum of 64M of ram and 1GB of kvm. These days,
machines often have many gigabytes of ram and a smaller amount of kvm.
libkvm+kgdb don't have a way to access physical ram that is not mapped
into kvm at the time of the crash dump, so the extra ram being dumped
is mostly wasted.
Minidumps invert the process. Instead of dumping physical memory in
in order to guarantee that all of kvm's backing is dumped, minidumps
instead dump only memory that is actively mapped into kvm.
amd64 has a direct map region that things like UMA use. Obviously we
cannot dump all of the direct map region because that is effectively
an old style all-physical-memory dump. Instead, introduce a bitmap
and two helper routines (dump_add_page(pa) and dump_drop_page(pa)) that
allow certain critical direct map pages to be included in the dump.
uma_machdep.c's allocator is the intended consumer.
Dumps are a custom format. At the very beginning of the file is a header,
then a copy of the message buffer, then the bitmap of pages present in
the dump, then the final level of the kvm page table trees (2MB mappings
are expanded into a 4K page mappings), then the sparse physical pages
according to the bitmap. libkvm can now conveniently access the kvm
page table entries.
Booting my test 8GB machine, forcing it into ddb and forcing a dump
leads to a 48MB minidump. While this is a best case, I expect minidumps
to be in the 100MB-500MB range. Obviously, never larger than physical
memory of course.
minidumps are on by default. It would want be necessary to turn them off
if it was necessary to debug corrupt kernel page table management as that
would mess up minidumps as well.
Both minidumps and regular dumps are supported on the same machine.
o Add the scc(4) manpage to the build.
o Update the uart(4) manpage to account for scc(4).
o Update the uart(4) module build to include support for scc(4).
