There's no need to special case 32-bit AIM to short circuit processing.
Some AIM CPUs can handle 36 bit addresses, and 64-bit CPUs can run 32-bit
OSes, so this will allow us to expand for that in the future if we desire.
The interrupt map wasn't being allocated properly, preventing IRQs from being
allocated to children of the PCIe bus. Fix this by cloning the ofw_pcib_pci
code, which handles all cases -- device tree and probed.
In the future this may become a subclass of the ofw_pcib_pci driver, but as
that's not an exported class, it's cloned for now.
MFC after: 3 weeks
* Check TLB1 in all mapdev cases, in case the memattr matches an existing
mapping (doesn't need to be MAP_DEFAULT).
* Fix mapping where the starting address is not a multiple of the widest size
base. For instance, it will now properly map 0xffffef000, size 0x11000 using
2 TLB entries, basing it at 0x****f000, instead of 0x***00000.
MFC after: 2 weeks
similar to the kernel memory allocator.
This simplifies NUMA allocation because the domain will be known at wait
time and races between failure and sleeping are eliminated. This also
reduces boilerplate code and simplifies callers.
A wait primitive is supplied for uma zones for similar reasons. This
eliminates some non-specific VM_WAIT calls in favor of more explicit
sleeps that may be satisfied without new pages.
Reviewed by: alc, kib, markj
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
According to EREF rlwinm is supposed to clear the upper 32 bits of the
register of 64-bit cores. However, from experience it seems there's a bug
in the e5500 which causes the result to be duplicated in the upper bits of
the register. This causes problems when applied to stashed SRR1 accessed
to retrieve context, as the upper bits are not masked out, so a
set_mcontext() fails. This causes sigreturn() to in turn return with
EINVAL, causing make(1) to exit with error.
This bit is unused in e500mc derivatives (including e5500), so could just be
conditional on non-powerpc64, but there may be other non-Freescale cores
which do use it. This is also the same as the POW bit on Book-S, so could
be cleared unconditionally with the only penalty being a few clock cycles
for these two interrupts.
When the segment count is > 16 it spills into an 'indirect descriptor list',
which immediately follows the main table, but the indirect list is entry 15, so
needs to be skipped for the general list.
The Freescale SATA controller has many similarities to AHCI controllers, so
this driver is a heavily modified AHCI driver. Currently it seems to only
do SATA 1.0 speeds (~100-150MB/s), so there is still room for improvement.
Still to be done:
* Address erratum SATA-A-006187 -- Spread Spectrum Support (intermittent
non-recoverable transient data integrity error seen when SSC enabled).
* Linux doesn't read the log page as it hangs on the P1022. See if that's
applicable to this, and address accordingly.
* Try to determine what's holding back performance, and address it.
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D6071
We already pass -many to the assembler, and -me500 drops 64-bit instruction
handling, for some reason only breaking module building for 64-bit kernels.
Additionally, build with CTF for dtrace.
gcc complains "cast to pointer from integer of different size". phandle_t is
*always* a uint32_t, so treat it as such, not as a pointer. Fixes 64-bit build.
This brings it closer to par with GENERIC64. In the future I hope to have a
GENERIC64-E and GENERIC-E kernels as Book-E analogues to the GENERIC64/GENERIC
AIM kernels.
Rework the dTSEC and FMan drivers to be more like a full bus relationship,
so that dtsec can use bus_alloc_resource() instead of trying to handle the
offset from the dts. This required taking some code from the sparc64 ebus
driver to allow subdividing the fman region for the dTSEC devices.
This adds some support for ARM as well as 64-bit. 64-bit on PowerPC is
currently not working, and ARM support has not been completed or tested on the
FreeBSD side.
As this was imported from a Linux tree, it includes some Linux-isms
(ioread/iowrite), so compile with the LinuxKPI for now. This may change in the
future.
- allocate value for new AT_HWCAP2 auxiliary vector on all platforms.
- expand 'struct sysentvec' by new 'u_long *sv_hwcap2', in exactly
same way as for AT_HWCAP.
MFC after: 1 month
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D12699
HEAD. Enable VIMAGE in GENERIC kernels and some others (where GENERIC does
not exist) on HEAD.
Disable building LINT-VIMAGE with VIMAGE being default.
This should give it a lot more exposure in the run-up to 12 to help
us evaluate whether to keep it on by default or not.
We are also hoping to get better performance testing.
The feature can be disabled using nooptions.
Requested by: many
Reviewed by: kristof, emaste, hiren
X-MFC after: never
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D12639
* Book-E can have Altivec exceptions, so move it out of the AIM-only block.
* Print the right DSI trap mode (read vs write) for Book-E
While here, fix some whitespace found while reviewing other diffs.
These devices bring the configs closer to a desktop-like (GENERIC) kernel
config.
* The Freescale DIU support was added to the config in r306358.
Without keyboard support video support is nearly pointless, so add ukbd and
ums.
* The AmigaOne X5000, and P1022 devboard, both use a variant of the ds1307 RTC
* cpufreq scaling is currently supported by the p1022. More SoCs will be added
eventually.
__builtin_frame_address with a non-zero argument is unsafe and rejected by
newer gcc. Since it doesn't seem to impact the stacktrace, don't bother
with gymnastics to unwind to a different frame for starting.
PR: kern/220118
MFC after: 2 weeks
All the Book-E world is no longer e500v{1,2}. e500mc the 64-bit derivatives do
not use the DOZE/NAP bits with MSR[WE], instead using the `wait' instruction to
wait for interrupts, and SoC plane controls (via CCSR) for power management.
MFC after: 1 week
A new 'u_long *sv_hwcap' field is added to 'struct sysentvec'. A
process ABI can set this field to point to a value holding a mask of
architecture-specific CPU feature flags. If an ABI does not wish to
supply AT_HWCAP to processes the field can be left as NULL.
The support code for AT_EHDRFLAGS was already present on all systems,
just the #define was not present. This is a step towards unifying the
AT_* constants across platforms.
Reviewed by: kib
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D12290
P5040/P5021 have the same number of LAWs as P5020. There may be a better way of
getting the count from the FDT (fsl,num-laws property on soc/corenet-law or
soc/ecm-law), but that's not supported everywhere, so we still need this check
for those other cases.
These processors may not be supported yet, but add them for completion.
POWER9 is planned for support. e300 may work (based on 603e core).
P5040/P5021 are similar to P5020, so should work as well. One addition is
needed for P5040, to support the number of LAWs, and will be a separate commit.
redundant initializations.
Hard-code base = 0, height = (approx. 1/8 of the boot-time font height)
in all cases, and remove the BIOS/MD support for setting these values.
This asks for an underline cursor sized for the boot-time font instead
of various less hard-coded but worse values. I used that think that
the x86 BIOS always gave the same values as the above hard-coding, but
on 1 of my systems it gives the wrong value of base = 1.
The remaining BIOS fields are shift_state and bell_pitch. These are now
consistently not explicitly reinitialized to 0. All sc_get_bios_value()
functions except x86's are now empty, and the only useful thing that x86
returns is shift_state. This really belongs in atkbdc, but heavier
use of the BIOS to read the more useful typematic rate has been removed
there. fb still makes much heavier use of the BIOS.
P1022 and MPC8536 include a 'jog' feature for clock control
(jog being a slower form of run mode). This is done by changing the
PLL multiplier, and cannot be done if any core is in doze or sleep mode.
--Remove special-case handling of sparc64 bus_dmamap* functions.
Replace with a more generic mechanism that allows MD busdma
implementations to generate inline mapping functions by
defining WANT_INLINE_DMAMAP in <machine/bus_dma.h>. This
is currently useful for sparc64, x86, and arm64, which all
implement non-load dmamap operations as simple wrappers
around map objects which may be bus- or device-specific.
--Remove NULL-checked bus_dmamap macros. Implement the
equivalent NULL checks in the inlined x86 implementation.
For non-x86 platforms, these checks are a minor pessimization
as those platforms do not currently allow NULL maps. NULL
maps were originally allowed on arm64, which appears to have
been the motivation behind adding arm[64]-specific barriers
to bus_dma.h, but that support was removed in r299463.
--Simplify the internal interface used by the bus_dmamap_load*
variants and move it to bus_dma_internal.h
--Fix some drivers that directly include sys/bus_dma.h
despite the recommendations of bus_dma(9)
Reviewed by: kib (previous revision), marius
Differential Revision: https://reviews.freebsd.org/D10729
Without disabling interrupts it's possible for another thread to preempt
and update the registers post-read (tlb1_read_entry) or pre-write
(tlb1_write_entry), and confuse the kernel with mixed register states.
MFC after: 2 weeks
AKA Make time_t 64 bits on powerpc(32).
PowerPC currently (until now) was one of two architectures with a 32-bit time_t
on 32-bit archs (the other being i386). This is an ABI breakage, so all ports,
and all local binaries, *must* be recompiled.
Tested by: andreast, others
MFC after: Never
Relnotes: Yes
Follow up r319935 by actually committing the mpc85xx_get_platform_clock()
function. This function was created to facilitate other development, and I
thought I had committed it earlier.
Some blocks depend on the platform clock rather than the system clock.
The System clock is derived from the platform clock as one-half the
platform clock. Rewrite mpc85xx_get_system_clock() to use the new
function.
Pointy-hat to: jhibbits
struct thread.
For all architectures, the syscall trap handlers have to allocate the
structure on the stack. The structure takes 88 bytes on 64bit arches
which is not negligible. Also, it cannot be easily found by other
code, which e.g. caused duplication of some members of the structure
to struct thread already. The change removes td_dbg_sc_code and
td_dbg_sc_nargs which were directly copied from syscall_args.
The structure is put into the copied on fork part of the struct thread
to make the syscall arguments information correct in the child after
fork.
This move will also allow several more uses shortly.
Reviewed by: jhb (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
X-Differential revision: https://reviews.freebsd.org/D11080
from machine/proc.h, consistently on all architectures.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
X-Differential revision: https://reviews.freebsd.org/D11080
The ccr(4) driver supports use of the crypto accelerator engine on
Chelsio T6 NICs in "lookaside" mode via the opencrypto framework.
Currently, the driver supports AES-CBC, AES-CTR, AES-GCM, and AES-XTS
cipher algorithms as well as the SHA1-HMAC, SHA2-256-HMAC, SHA2-384-HMAC,
and SHA2-512-HMAC authentication algorithms. The driver also supports
chaining one of AES-CBC, AES-CTR, or AES-XTS with an authentication
algorithm for encrypt-then-authenticate operations.
Note that this driver is still under active development and testing and
may not yet be ready for production use. It does pass the tests in
tests/sys/opencrypto with the exception that the AES-GCM implementation
in the driver does not yet support requests with a zero byte payload.
To use this driver currently, the "uwire" configuration must be used
along with explicitly enabling support for lookaside crypto capabilities
in the cxgbe(4) driver. These can be done by setting the following
tunables before loading the cxgbe(4) driver:
hw.cxgbe.config_file=uwire
hw.cxgbe.cryptocaps_allowed=-1
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D10763
The current method only sort of works, and usually doesn't work reliably.
Also, on Book-E the return address from DEBUG exceptions is not the sentinel
addresses, so it won't exit the loop correctly.
Fix this by better handling trap frames during unwinding, and using the
common trap handler for debug traps, as the code in that segment is
identical between the two.
MFC after: 1 week
in place. To do per-cpu stats, convert all fields that previously were
maintained in the vmmeters that sit in pcpus to counter(9).
- Since some vmmeter stats may be touched at very early stages of boot,
before we have set up UMA and we can do counter_u64_alloc(), provide an
early counter mechanism:
o Leave one spare uint64_t in struct pcpu, named pc_early_dummy_counter.
o Point counter(9) fields of vmmeter to pcpu[0].pc_early_dummy_counter,
so that at early stages of boot, before counters are allocated we already
point to a counter that can be safely written to.
o For sparc64 that required a whole dummy pcpu[MAXCPU] array.
Further related changes:
- Don't include vmmeter.h into pcpu.h.
- vm.stats.vm.v_swappgsout and vm.stats.vm.v_swappgsin changed to 64-bit,
to match kernel representation.
- struct vmmeter hidden under _KERNEL, and only vmstat(1) is an exclusion.
This is based on benno@'s 4-year old patch:
https://lists.freebsd.org/pipermail/freebsd-arch/2013-July/014471.html
Reviewed by: kib, gallatin, marius, lidl
Differential Revision: https://reviews.freebsd.org/D10156
The MFC will include a compat definition of smp_no_rendevous_barrier()
that calls smp_no_rendezvous_barrier().
Reviewed by: gnn, kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D10313
Many devices are clocked from the SoC's platform clock / 2. Some device nodes
include their own clock-frequency property, while others are dependent on the
SoC's bus-frequency property instead. To simplify, add a helper function to get
this clock.
I fixed this in 1997, but the fix was over-engineered and fragile and
was broken in 2003 if not before. i386 parameters were copied to 8
other arches verbatim, mostly after they stopped working on i386, and
mostly without the large comment saying how the values were chosen on
i386. powerpc has a non-verbatim copy which just changes the uncritical
parameter and seems to add a sign extension bug to it.
Just treat negative offsets as offsets if they are no more negative than
-db_offset_max (default -64K), and remove all the broken parameters.
-64K is not very negative, but it is enough for frame and stack pointer
offsets since kernel stacks are small.
The over-engineering was mainly to go more negative than -64K for the
negative offset format, without affecting printing for more than a
single address.
Addresses in the top 64K of a (full 32-bit or 64-bit) address space
are now printed less well, but there aren't many interesting ones.
For arches that have many interesting ones very near the top (e.g.,
68k has interrupt vectors there), there would be no good limit for
the negative offset format and -64K is a good as anything.
Extend the Book-E pmap to support 64-bit operation. Much of this was taken from
Juniper's Junos FreeBSD port. It uses a 3-level page table (page directory
list -- PP2D, page directory, page table), but has gaps in the page directory
list where regions will repeat, due to the design of the PP2D hash (a 20-bit gap
between the two parts of the index). In practice this may not be a problem
given the expanded address space. However, an alternative to this would be to
use a 4-level page table, like Linux, and possibly reduce the available address
space; Linux appears to use a 46-bit address space. Alternatively, a cache of
page directory pointers could be used to keep the overall design as-is, but
remove the gaps in the address space.
This includes a new kernel config for 64-bit QorIQ SoCs, based on MPC85XX, with
the following notes:
* The DPAA driver has not yet been ported to 64-bit so is not included in the
kernel config.
* This has been tested on the AmigaOne X5000, using a MD_ROOT compiled in
(total size kernel+mdroot must be under 64MB).
* This can run both 32-bit and 64-bit processes, and has even been tested to run
a 32-bit init with 64-bit children.
Many thanks to stevek and marcel for getting Juniper's FreeBSD patches open
sourced to be used here, and to stevek for reviewing, and providing some
historical contexts on quirks of the code.
Reviewed by: stevek
Obtained from: Juniper (in part)
MFC after: 2 months
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D9433
===
From Nathan Whitehorn:
Open Firmware runs in virtual mode on the Powermac G5. This runs inside the
kernel page table, which preserves all address translations made by OF before
the kernel starts; as a result, the kernel address space is a strict superset of
OF's.
Where this explodes is if OF uses an unmapped SLB entry. The SLB fault handler
runs in real mode and refers to the PCPU pointer in SPRG0, which blows up the
kernel. Having a value of SPRG0 that works for the kernel is less fatal than
preserving OF's value in this case.
===
The result of this is seemingly random panics from NULL dereferences, or hangs
immediately upon boot. By not restoring SPRG0 for Open Firmware entry the
kernel PCPU pointer is preserved and SLB faults are successful, resulting in a
stable kernel.
PR: 205458
Reported by: several (over bugzilla, lists, IRC)
Reviewed by: andreast
Tested by: many (various forms)
MFC after: 2 weeks
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
Add the necessary bits to enable kernel breakpoints for Book-E. The entrypoint
for program exception is very trivial, so rather than expand it to be similar to
AIM, add it into the standard trap handler.
This wasn't blocked out as Book-E specific because it is only a minor redundancy
over AIM, which should have already called db_trap_glue() at this point. If
it's going to panic with a fatal trap anywya, it doesn't matter if it goes
through this path again.
When committing DTrace in 2012/2013 era I inadvertently broke breakpoints, by
setting EXC_DTRACE to the same value as BKPT_INST. Change EXC_DTRACE to a
different, yet logically identical, trap (tw <all>,31,31).
MFC after: 2 weeks
This is required for FDT's standard "reg-io-width" property
(similar to "reg-shift" property) found in many DTS files.
This fixes operation on Altera Arria 10 SOC Development Kit,
where standard ns8250 uart allows 4-byte access only.
Reviewed by: kan, marcel
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9785
Convert PCIe hot plug support over to asking the firmware, if any, for
permission to use the HotPlug hardware. Implement pci_request_feature
for ACPI. All other host pci connections to allowing all valid feature
requests.
Sponsored by: Netflix
with geom_flashmap(4) and teach it about MMC for slicing enhanced
user data area partitions. The FDT slicer still is the default for
CFI, NAND and SPI flash on FDT-enabled platforms.
- In addition to a device_t, also pass the name of the GEOM provider
in question to the slicers as a single device may provide more than
provider.
- Build a geom_flashmap.ko.
- Use MODULE_VERSION() so other modules can depend on geom_flashmap(4).
- Remove redundant/superfluous GEOM routines that either do nothing
or provide/just call default GEOM (slice) functionality.
- Trim/adjust includes
Submitted by: jhibbits (RouterBoard bits)
Reviewed by: jhibbits
Implement get_pcpu() for amd64/sparc64/mips/powerpc, and use it to
replace pcpu_find(curcpu) in MI code.
Reviewed by: andreast, kan, lidl
Tested by: lidl(mips, sparc64), andreast(powerpc)
Differential Revision: https://reviews.freebsd.org/D9587
The types are for the byte offset and page index in vm object. They
are similar to off_t, which is defined as 64bit MI integer. Using MI
definitions will allow to provide consistent MD values of vm
object-related maximum sizes.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
The switch to get_pcpu() in MI code seems to cause hangs on MIPS.
Back out until we can get a better idea of what's happening there.
Reported by: kan, lidl
Freescale added the E.D profile to e500mc and derivative cores. From
Freescale's EREF reference manual this is enabled by a bit in HID0 and should
otherwise default to traditional debug. However, none of the Freescale cores
support that bit, and instead always use E.D. This results in kernel panics
using the standard debug on e500mc+ cores.
Enhanced debug allows debugging of interrupts, including critical interrupts,
as it uses a different save/restore registers (srr*). At this time we don't use
this ability, so instead share the core of the debug handler code between both
handlers.
MFC after: 3 weeks
The desired behavior of atomic_fcmpset_() is to always exit on error. Instead
of retrying on lost reservation, leave the retry to the caller, and return
error.
Reported by: kib
There are no alternatives defined, so there's no point in keeping them. Also,
they weren't around every inline asm block anyway. Without __GNUCLIKE_ASM
defined, the guarded functions return garbage.
Reported by: Andrew Thompson
Summary:
Clang throws the following warning in powerpc intr_machdep:
/usr/src/sys/powerpc/powerpc/intr_machdep.c:454:15: warning: comparison of
constant -1 with expression of type 'enum intr_trigger' is always false
[-Wtautological-constant-out-of-range-compare]
if (i->trig == -1)
~~~~~~~ ^ ~~
This may lead to legitimate problems with aggressive optimizations, if not now
then in the future. To avoid this, add a new enum, INTR_TRIG_INVALID, set to
-1, and use this new enumeration in these checks.
Test Plan: Compile test.
Reviewed By: jhb, kib
Differential Revision: https://reviews.freebsd.org/D9300
Summary:
atomic_fcmpset_*() is analogous to atomic_cmpset(), but saves off the read value
from the target memory location into the 'old' pointer in the case of failure.
Requested by: mjg
Differential Revision: https://reviews.freebsd.org/D9325
Building kernel with devel/powerpc64-gcc (6.2.0) yields the following error:
/usr/src/sys/powerpc/powerpc/db_trace.c:299:20: error: calling
'__builtin_frame_address' with a nonzero argument is unsafe
[-Werror=frame-address]
Work around this by dereferencing the frame address manually instead.
PR: 215600
Reported by: Mark Millard <markmi AT dsl-only DOT net>
MFC after: 2 weeks
Clang apparently requires the explicit form of this instruction, and rejects
uses which ignore the optional cmpD register. This was the only use of the
shorthand form of the instruction, so just fix it up to match the others.
PR: kern/215681
Submitted by: Mark Millard
Reported by: Mark Millard <markmi _AT_ dsl-only.net>
MFC after: 2 weeks
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
There are places where checks are made against VM_MAX_KERNEL_ADDRESS, or
virtual_end (set to VM_MAX_KERNEL_ADDRESS). With 32-bit checks, an address will
always be less than or equal to 0xffffffff. Drop a page, so those checks can
terminate loops safely.
The sim_vid, hba_vid, and dev_name fields of struct ccb_pathinq are
fixed-length strings. AFAICT the only place they're read is in
sbin/camcontrol/camcontrol.c, which assumes they'll be null-terminated.
However, the kernel doesn't null-terminate them. A bunch of copy-pasted code
uses strncpy to write them, and doesn't guarantee null-termination. For at
least 4 drivers (mpr, mps, ciss, and hyperv), the hba_vid field actually
overflows. You can see the result by doing "camcontrol negotiate da0 -v".
This change null-terminates those fields everywhere they're set in the
kernel. It also shortens a few strings to ensure they'll fit within the
16-character field.
PR: 215474
Reported by: Coverity
CID: 1009997 1010000 1010001 1010002 1010003 1010004 1010005
CID: 1331519 1010006 1215097 1010007 1288967 1010008 1306000
CID: 1211924 1010009 1010010 1010011 1010012 1010013 1010014
CID: 1147190 1010017 1010016 1010018 1216435 1010020 1010021
CID: 1010022 1009666 1018185 1010023 1010025 1010026 1010027
CID: 1010028 1010029 1010030 1010031 1010033 1018186 1018187
CID: 1010035 1010036 1010042 1010041 1010040 1010039
Reviewed by: imp, sephe, slm
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9037
Differential Revision: https://reviews.freebsd.org/D9038
When importing for r309309, as part of conflict resolution, too much extra was
removed, resulting in bad disassembly for branches. Correct this.
Also re-apply the 0->NULL change from r298052.
X-MFC-With: r309309
Before this, it would cause the one consumer of this API in powerpc usage
(dev/dpaa) to set the PTE WIMG flags to empty instead of --M-, making the
cache-enabled buffer portals non-coherent.
Bring in the most recent copy of NetBSD's db_disasm, to fix bugs and add more
instructions.
* Fix several bugs in the disassembler, most notably the disassembly of the
rlwi* instructions, the original reason for bringing in this change.
* Add more registers to the SPR list
* Add more instructions to the opcode table
Obtained from: NetBSD
MFC after: 2 weeks
MPC750 User Manual Errata (rev 1) adds a note to C.4.2.2 noting that mtsr,
mtsrin, and mtmsr all require a isync after the instruction and before data
address translation uses any of the segment registers. This should make FreeBSD
run correctly on the G3 again.
Reported by: Mark Millard
MFC after: 1 week
r309017 removed two fields from struct vmmeter, which is embedded in struct
pcpu. This caused the struct size to change, triggering the CTASSERT in
sys/pcpu.h. Add the extra 8 bytes back in as padding.
vmpage requires struct pmap to exist and contain a pm_stats field. As of
r308817, either AIM or BOOKE is required to be set in order to get their
respective pmap structs. Rather than expose them both, or try to unify them
unnecessarily, add a third option which contains only a pm_stats field, and
change the two existing pmap structures to place the common fields at the
beginning of the struct. This actually fixes the stats collection by libkvm on
AIM hardware, because before it was accessing a possibly different offset, which
would cause it to read garbage.
Bump __FreeBSD_version to denote this ABI change, so that ports which depend on
libkvm can be rebuilt.
Change the pv_tracked flag to an int, just in case userspace decides to include
this file and defines BOOKE.
Guard this block from unintentional inclusion with ifdef BOOKE.
Reported by: emaste
Drop the tracking down to the pmap layer, with optimizations to only track
necessary pages. This should give a (slight) performance improvement, as well
as a stability improvement, as the tracking is already mostly handled by the
pmap layer.
Summary:
This implements part of the gpio-poweroff and gpio-restart device tree
bindings. Optional properties are not handled currently. It also currently
only supports level-triggered reset.
Reviewed By: gonzo
Differential Revision: https://reviews.freebsd.org/D8521
Linux has a slightly different device tree definition for DPAA than originally
done in the FreeBSD driver. This changes the driver to be mostly compatible
with the Linux device tree definitions. Currently the differences are:
bman-portals: compatible = "fsl,bman-portals" (Linux is "simple-bus")
qman-portals: compatible = "fsl,qman-portals" (Linux is "simple-bus")
fman: compatible = "fsl,fman" (Linux is "simple-bus")
The Linux device tree doesn't specify anything for rgmii in the mdio. This
change still requires the device tree to specify the phy-handle, and doesn't yet
support tbi.
Summary:
i.MX5 and PowerPC use a very similar eSDHC controller, which is also
similar to the uSDHC controller used by i.MX6. The imx_sdhci driver works
almost completely with PowerPC, with some minor tweaks.
There is one caveat with this: reset currently does not work on PowerPC, so has
been #ifdef'd out until this can be tracked down and fixed. If resets are done
the controller will timeout all data transactions. Without a reset, it appears
to work just fine.
This is part 3, following up r308186 and r308187.
Test Plan:
This has been tested on a PowerPC QorIQ P1022 board. It has not been
tested on i.MX, but no regressions are expected.
Reviewed By: imp
Differential Revision: https://reviews.freebsd.org/D8407
Summary:
The Freescale e500v2 PowerPC core does not use a standard FPU.
Instead, it uses a Signal Processing Engine (SPE)--a DSP-style vector processor
unit, which doubles as a FPU. The PowerPC SPE ABI is incompatible with the
stock powerpc ABI, so a new MACHINE_ARCH was created to deal with this.
Additionaly, the SPE opcodes overlap with Altivec, so these are mutually
exclusive. Taking advantage of this fact, a new file, powerpc/booke/spe.c, was
created with the same function set as in powerpc/powerpc/altivec.c, so it
becomes effectively a drop-in replacement. setjmp/longjmp were modified to save
the upper 32-bits of the now-64-bit GPRs (upper 32-bits are only accessible by
the SPE).
Note: This does _not_ support the SPE in the e500v1, as the e500v1 SPE does not
support double-precision floating point.
Also, without a new MACHINE_ARCH it would be impossible to provide binary
packages which utilize the SPE.
Additionally, no work has been done to support ports, work is needed for this.
This also means no newer gcc can yet be used. However, gcc's powerpc support
has been refactored which would make adding a powerpcspe-freebsd target very
easy.
Test Plan:
This was lightly tested on a RouterBoard RB800 and an AmigaOne A1222
(P1022-based) board, compiled against the new ABI. Base system utilities
(/bin/sh, /bin/ls, etc) still function appropriately, the system is able to boot
multiuser.
Reviewed By: bdrewery, imp
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D5683
Instead replace it with a different hack, that turns fman into a simplebus
subclass, and maps its children within its address space.
Since all PHY communication is done through dtsec0's mdio space, the FDT
contains a reference to the dtsec0 mdio handle in all nodes that need it.
Instead of using Freescale's implementation for MII access, use our own (copied
loosely from the eTSEC driver, and could possibly be merged eventually). This
lets us access the registers directly rather than needing a full dtsec interface
just to access the registers.
Future directions will include turning fman into more of a simplebus, and not
mapping the region and playing games. This will require changes to the dtsec
driver to make it a child of fman, and possibly other drivers as well.
Static variables aren't MP-safe, and this was causing bizarre segfaults on a
dual-core e500v2 system (P1022).
Still left is one static variable, which should be moved into the pcb instead,
but as illegal instructions haven't been hit yet, it's lower priority.
MFC after: 1 week
r306065/r306067 introduced ofw_parse_bootargs(), setting environment variables
from Open Firmware's /chosen/bootargs property. On systems booting with
loader(8) (meaning, most systems), the initial static kenv is created with no
extra space, causing kern_setenv() to panic. Since these already have the
environment set directly, there is no need to parse bootargs anyway.
Found by: swills
Using the device pager with /dev/kmem is not stable since KVA mappings
are transient, but the device pager caches the PA associated with a
given offset forever. Interestingly, mips' implementation of
memmap() already refused requests for /dev/kmem.
Note that kvm_read/kvm_write do not use mmap, but use read and write on
/dev/kmem, so this should not affect libkvm users.
Reviewed by: kib
MFC after: 2 months
with no creative content. Include "lost" changes from git:
o Use /dev/efi instead of /dev/efidev
o Remove redundant NULL checks.
Submitted by: kib@, dim@, zbb@, emaste@
to add actions that run when a TCP frame is sent or received on a TCP
session in the ESTABLISHED state. In the base tree, this functionality is
only used for the h_ertt module, which is used by the cc_cdg, cc_chd, cc_hd,
and cc_vegas congestion control modules.
Presently, we incur overhead to check for hooks each time a TCP frame is
sent or received on an ESTABLISHED TCP session.
This change adds a new compile-time option (TCP_HHOOK) to determine whether
to include the hhook(9) framework for TCP. To retain backwards
compatibility, I added the TCP_HHOOK option to every configuration file that
already defined "options INET". (Therefore, this patch introduces no
functional change. In order to see a functional difference, you need to
compile a custom kernel without the TCP_HHOOK option.) This change will
allow users to easily exclude this functionality from their kernel, should
they wish to do so.
Note that any users who use a custom kernel configuration and use one of the
congestion control modules listed above will need to add the TCP_HHOOK
option to their kernel configuration.
Reviewed by: rrs, lstewart, hiren (previous version), sjg (makefiles only)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D8185
Setting the doze registers wasn't actually working, and was being masked by a
bad #ifdef. Since the #ifdef was fixed, now e500mc-based SoCs hang at idle.
Fix this by using the intended wait.
MFC after: 1 week
Summary:
This enables some features of the DIU, using a static configuration,
specified either via a 'edid' property on the 'display' FDT node, or a
'video-mode' environment variable (bootarg). 'video-mode' was chosen because it
matches u-boot's naming, so it can be set with:
setenv bootargs video-mode=${video-mode}
at the u-boot CLI.
Mouse cursor is not supported currently, as a hardware cursor is not supported
by framebuffer VT yet. Currently it only supports a 32bpp ARGB (actually BGRA)
format, and only a single composite plane, at up to 1280x1024.
Differential Revision: https://reviews.freebsd.org/D8022
Summary:
If the environment variable is set, U-boot adds a 'bootargs' property to
/chosen. This is already handled by ARM and MIPS, but should be handled in a
central location. For now, ofw_subr.c is a good place until we determine if it
should be moved to init_main.c, or somewhere more central to all architectures.
Eventually arm and mips should be modified to use ofw_parse_bootargs() as well,
rather than using the duplicate code already.
Reviewed By: adrian
Differential Revision: https://reviews.freebsd.org/D7846
Move PMAP_TS_REFERENCED_MAX out of the various pmap implementations and
into vm/pmap.h, and describe what its purpose is. Eliminate the archaic
"XXX" comment about its value. I don't believe that its exact value, e.g.,
5 versus 6, matters.
Update the arm64 and riscv pmap implementations of pmap_ts_referenced()
to opportunistically update the page's dirty field.
On amd64, use the PDE value already cached in a local variable rather than
dereferencing a pointer again and again.
Reviewed by: kib, markj
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D7836
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Reviewed by: np
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7599
pmap_early_io_map()/pmap_early_io_unmap(), if used in pairs, should be used in
the form:
pmap_early_io_map()
..do stuff..
pmap_early_io_unmap()
Without other allocations in the middle. Without reclaiming memory this can
leave large holes in the device space.
While here, make a simple change to the unmap loop which now permits it to unmap
multiple TLB entries in the range.
Idle page zeroing has been disabled by default on all architectures since
r170816 and has some bugs that make it seemingly unusable. Specifically,
the idle-priority pagezero thread exacerbates contention for the free page
lock, and yields the CPU without releasing it in non-preemptive kernels. The
pagezero thread also does not behave correctly when superpage reservations
are enabled: its target is a function of v_free_count, which includes
reserved-but-free pages, but it is only able to zero pages belonging to the
physical memory allocator.
Reviewed by: alc, imp, kib
Differential Revision: https://reviews.freebsd.org/D7714
Summary:
1) Attach problem - mpc85xx_probe() relies on fact that 0xfff0 mask matches all
QorIQ CPUs what is not true since e6500. This shall be reworked to match against
all supported CPUs.
2) There is no any reason for operating system to re-program or anyhow else
touch the LAWs programmed by firmware (u-boot). Right now mpc85xx_attach()
removes all LaW entries except for DRAM. This causes MCE to be generated when
later any of driver maps DTB-provided hardware addresses which do not exist
anymore because corresponding LaWs were removed.
Submitted by: Ivan Krivonos <int0dster_AT_gmail.com>
Differential Revision: https://reviews.freebsd.org/D7663
Summary:
First time BSS is cleared in booke_init(), Second time it's cleared in
powerpc_init(). Any variable initialized between two those guys gets wiped out
what is wrong. In particular it wipes tlb1_entries initialized by tlb1_init(),
which was fine when tlb1_init() was called a second time, but this was removed
in r304656.
Submitted by: Ivan Krivonos <int0dster_gmail.com>
Differential Revision: https://reviews.freebsd.org/D7638
Summary:
Kernel maps only one page of FDT. When FDT is more than one page in size, data
TLB miss occurs on memmove() when FDT is moved to kernel storage
(sys/powerpc/booke/booke_machdep.c, booke_init())
This introduces a pmap_early_io_unmap() to complement pmap_early_io_map(), which
can be used for any early I/O mapping, but currently is only used when mapping
the fdt.
Submitted by: Ivan Krivonos <int0dster_gmail.com>
Differential Revision: https://reviews.freebsd.org/D7605
Summary:
There is no need to call tlb1_init() twice. Now it is called first time from
booke_init() and second time from powerpc_init() (where it is under BOOKE
switch). Although this does not cause immediate problems in the mainline kernel,
this can lead to undesirable side effects like two TLB entries with the same VA
in the TLB1. Presence of two TLB entries with the same VA can hang CPU.
Test Plan:
Add initial mapping for UART to the tlb1_init(), build and boot the kernel,
ensure that mapping presents only once (most convinient way - through Lauterbah
or similar hardware debugger)
Submitted by: Ivan Krivonos <int0dster_gmail.com>
Differential Revision: https://reviews.freebsd.org/D7607
Summary: Current booke/pmap code ignores mas7 and mas8 on e6500 CPU.
Submitted by: Ivan Krivonos <int0dster_gmail.com>
Differential Revision: https://reviews.freebsd.org/D7606
mpc85xx_map_dcsr() returns a vm_offset_t, not an error code.
mpc85xx_fix_errata() will gracefully exit if mpc85xx_map_dcsr() returns 0, as
that indicates an error (NULL pointer).
__syncicache() only syncs the icache on the current CPU, it doesn't touch the
cache on any other core. Replace the call with cpu_flush_dcache() instead.
Since bp_kernload is not touched again by the boot CPU in this code path, dcbf
is no less efficient than the dcbst from __syncicache() by invalidating the
cache line.
Summary:
There is often a need at the debugger to print arbitrary special
purpose registers (SPRs) on PowerPC. Using a rewritable asm stub, print any SPR
provided on the command line.
Note, as there is no checking in this, attempting to print a nonexistent SPR
may cause a Program exception (illegal instruction, or boundedly undefined).
Note also that this relies on the kernel text pages being writable. If in the
future this is made not the case, this will need to be reworked.
Test Plan:
Printing the Processor Version Register (PVR, SPR 287):
db> show spr 11f
SPR 287(11f): 80240012
Differential Revision: https://reviews.freebsd.org/D7403
Summary:
u-boot, following the ePAPR specification, puts secondary cores into a
spinloop at boot, rather than leaving them shut off. It then relies on the host
OS to write the correct values to a special spin table, located in coherent
memory (on newer implementations), or noncoherent memory (older
implementations).
This supports both implementations of ePAPR, as well as continuing to support
non-ePAPR booting, by first attempting to use the spintable, and falling back to
expecting non-started CPUs.
Test Plan:
Booted on a P5020 board. Tested before and after the changes.
Before the changes, prints the error "SMP: CPU 1 already out of hold-off state!"
and panics shortly thereafter. After the changes, same boot method lets it
complete boot.
Reviewed by: nwhitehorn
MFC after: 2 weeks
Relnotes: Yes
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D7494
Several files use the internal name of `struct device` instead of
`device_t` which is part of the public API. This patch changes all
`struct device *` to `device_t`.
The remaining occurrences of `struct device` are those referring to the
Linux or OpenBSD version of the structure, or the code is not built on
FreeBSD and it's unclear what to do.
Submitted by: Matthew Macy <mmacy@nextbsd.org> (previous version)
Approved by: emaste, jhibbits, sbruno
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D7447
Without enabling this bit, tlbre and tlbsx don't update the MAS7 register,
resulting in garbage in the register after a read (rather, the previous setting
of it for a tlbwe). This can result in mmu_booke_mapdev_attr() thinking
mappings that should match actually don't, because tlb1_read_entry() can't
determine the correct address of a given entry.
MFC after: 11-RELEASE
bouncing of unmapped buffers. Also treat userspace buffers as unmapped, to
avoid borrowing the UVA for copies. This allows sync'ing userspace buffers
outside the context of the owning process, and sync'ing bounced maps in
non-sleepable contexts.
This change is equivalent to r286787 for x86.
Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D3989
Summary:
MPC85XX and QorIQ are very similar. When the DPAA dTSEC driver was
added, QORIQ_DPAA was brought in as a config option to support the differences
in hardware register settings between QorIQ (e500mc-, e5500- based) SoCs and
QUICC (e500v1/e500v2-based) SoCs, particularly in the Local Access Window (LAW)
target settings.
Unify these settings using macros to hide details and ease porting, and use a
new function (mpc85xx_is_qoriq()) to distinguish between QorIQ and QUICC SoCs at
runtime.
An alternative to using the function could be to use a variable initialized at
platform attach time, which may incur less overhead at runtime. Since it's not
in the critical path once booted, this optimization doesn't seem necessary at
first pass.
Reviewed by: nwhitehorn
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D7294
Though the chances of the code in these sections changing are low, future-proof
the sections and use label math.
Renumber the surrounding areas to avoid duplicate label numbers.
L3 cache is not defined by Book-E, so is platform specific. Since it was
already moved for e500-based devices into mpc85xx in r292903, just eliminate it
altogether. Any device that supports L3 cache should have its own platform
means to enable it.
mp_maxid or CPU_FOREACH() as appropriate. This fixes a number of places in
the kernel that assumed CPU IDs are dense in [0, mp_ncpus) and would try,
for example, to run tasks on CPUs that did not exist or to allocate too
few buffers on systems with sparse CPU IDs in which there are holes in the
range and mp_maxid > mp_ncpus. Such circumstances generally occur on
systems with SMT, but on which SMT is disabled. This patch restores system
operation at least on POWER8 systems configured in this way.
There are a number of other places in the kernel with potential problems
in these situations, but where sparse CPU IDs are not currently known
to occur, mostly in the ARM machine-dependent code. These will be fixed
in a follow-up commit after the stable/11 branch.
PR: kern/210106
Reviewed by: jhb
Approved by: re (glebius)
Remove the use of fdt_data_to_res(), and instead construct the resources
manually. Additionally, avoid the 32-bit size limitation of fdt_data_get(), by
building physical addresses manually from the lbc ranges property.
Approved by: re@(gjb)
late boot: enable it explicitly after installing the page tables. If booting
from an FDT, also make sure to escape the firmware's MMU context early
before overwriting firmware page tables.
Approved by: re (gjb)
Most of the effect of setting MSR[SF] is that the CPU will stop ignoring
the high 32 bits of registers containing addresses in load/store
instructions. As such, the kernel was setting it only when it began to
need access to high memory. MSR[SF] also affects the operation of some
conditional instructions, however, and so setting it at late times could
subtly break code at very early times. This fixes use of the FDT mode in
loader, and FDT boot more generally, on 64-bit PowerPC systems.
Hardware provided by: IBM LTC
Approved by: re (kib)
threads, to make it less confusing and using modern kernel terms.
Rename the functions to reflect current use of the functions, instead
of the historic KSE conventions:
cpu_set_fork_handler -> cpu_fork_kthread_handler (for kthreads)
cpu_set_upcall -> cpu_copy_thread (for forks)
cpu_set_upcall_kse -> cpu_set_upcall (for new threads creation)
Reviewed by: jhb (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Approved by: re (hrs)
Differential revision: https://reviews.freebsd.org/D6731
After r285994, sysctl(8) was fixed to use 273.15 instead of 273.20 as 0C
reference and as result, the temperature read in sysctl(8) now exibits a
+0.1C difference.
This commit fix the kernel references to match the reference value used in
sysctl(8) after r285994.
Sponsored by: Rubicon Communications (Netgate)
PCI-express HotPlug support is implemented via bits in the slot
registers of the PCI-express capability of the downstream port along
with an interrupt that triggers when bits in the slot status register
change.
This is implemented for FreeBSD by adding HotPlug support to the
PCI-PCI bridge driver which attaches to the virtual PCI-PCI bridges
representing downstream ports on HotPlug slots. The PCI-PCI bridge
driver registers an interrupt handler to receive HotPlug events. It
also uses the slot registers to determine the current HotPlug state
and drive an internal HotPlug state machine. For simplicty of
implementation, the PCI-PCI bridge device detaches and deletes the
child PCI device when a card is removed from a slot and creates and
attaches a PCI child device when a card is inserted into the slot.
The PCI-PCI bridge driver provides a bus_child_present which claims
that child devices are present on HotPlug-capable slots only when a
card is inserted. Rather than requiring a timeout in the RC for
config accesses to not-present children, the pcib_read/write_config
methods fail all requests when a card is not present (or not yet
ready).
These changes include support for various optional HotPlug
capabilities such as a power controller, mechanical latch,
electro-mechanical interlock, indicators, and an attention button.
It also includes support for devices which require waiting for
command completion events before initiating a subsequent HotPlug
command. However, it has only been tested on ExpressCard systems
which support surprise removal and have none of these optional
capabilities.
PCI-express HotPlug support is conditional on the PCI_HP option
which is enabled by default on arm64, x86, and powerpc.
Reviewed by: adrian, imp, vangyzen (older versions)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D6136
This allows the PCI-PCI bridge driver to save a reference to the child
device in its softc.
Note that this required moving the "pci" device creation out of
acpi_pcib_attach(). Instead, acpi_pcib_attach() is renamed to
acpi_pcib_fetch_prt() as it's sole action now is to fetch the PCI
interrupt routing table.
Differential Revision: https://reviews.freebsd.org/D6021
Rescanning a PCI bus uses the following steps:
- Fetch the current set of child devices and save it in the 'devlist'
array.
- Allocate a parallel array 'unchanged' initalized with NULL pointers.
- Scan the bus checking each slot (and each function on slots with a
multifunction device).
- If a valid function is found, look for a matching device in the 'devlist'
array. If a device is found, save the pointer in the 'unchanged' array.
If a device is not found, add a new device.
- After the scan has finished, walk the 'devlist' array deleting any
devices that do not have a matching pointer in the 'unchanged' array.
- Finally, fetch an updated set of child devices and explicitly attach any
devices that are not present in the 'unchanged' array.
This builds on the previous changes to move subclass data management into
pci_alloc_devinfo(), pci_child_added(), and bus_child_deleted().
Subclasses of the PCI bus use custom rescan logic explicitly override the
rescan method to disable rescans.
Differential Revision: https://reviews.freebsd.org/D6018
When ORing in a register_t to a wider integer (vm_paddr_t), it gets sign
extended, so high addresses overwrite the upper word with all 0xf. Cast to the
unsigned form (u_register_t), to avoid this problem, and get correct addresses
printed.
With this, a static environment can be compiled in via config(5). This allows,
among other things, the use of a compiled-in debug console (hw.uart.dbgport) for
kgdb.
rounddown2 tends to produce longer lines than the original code
and when the code has a high indentation level it was not really
advantageous to do the replacement.
This tries to strike a balance between readability using the macros
and flexibility of having the expressions, so not everything is
converted.
Summary:
PowerPC Book-E SMP is currently broken for unknown reasons. Pull in
Semihalf changes made c2012 for e500mc/e5500, which enables booting SMP.
This eliminates the shared software TLB1 table, replacing it with
tlb1_read_entry() function.
This does not yet support ePAPR SMP booting, and doesn't handle resetting CPUs
already released (ePAPR boot releases APs to a spin loop waiting on a specific
address). This will be addressed in the near future by using the MPIC to reset
the AP into our own alternate boot address.
This does include a change to the dpaa/dtsec(4) driver, to mark the portals as
CPU-private.
Test Plan:
Tested on Amiga X5000/20 (P5020). Boots, prints the following
messages:
Adding CPU 0, pir=0, awake=1
Waking up CPU 1 (dev=1)
Adding CPU 1, pir=20, awake=1
SMP: AP CPU #1 launched
top(1) shows CPU1 active.
Obtained from: Semihalf
Relnotes: Yes
Differential Revision: https://reviews.freebsd.org/D5945
The ACPI and OFW PCI bus drivers as well as CardBus override this to
allocate the larger ivars to hold additional info beyond the stock PCI ivars.
This removes the need to pass the size to functions like pci_add_iov_child()
and pci_read_device() simplifying IOV and bus rescanning implementations.
As a result of this and earlier changes, the ACPI PCI bus driver no longer
needs its own device_attach and pci_create_iov_child methods but can use
the methods in the stock PCI bus driver instead.
Differential Revision: https://reviews.freebsd.org/D5891
Summary:
There is currently a 1GB hole between user and kernel address spaces
into which direct (1:1 PA:VA) device mappings go. This appears to go largely
unused, leaving all devices to contend with the 128MB block at the end of the
32-bit space (0xf8000000-0xffffffff). This easily fills up, and needs to be
densely packed. However, dense packing wastes precious TLB1 space, of which
there are only 16 (e500v2) or 64(e5500) entries available.
Change this by using the 1GB space for all device mappings, and allow the kernel
to use the entire upper 1GB for KVA. This also allows us to use sparse device
mappings, freeing up TLB entries.
Test Plan: Boot tested on p5020.
Differential Revision: https://reviews.freebsd.org/D5832
Instead of providing a wrapper around device_delete_child() that the PCI
bus and child bus drivers must call explicitly, move the bulk of the logic
from pci_delete_child() into a bus_child_deleted() method
(pci_child_deleted()). This allows PCI devices to be safely deleted via
device_delete_child().
- Add a bus_child_deleted method to the ACPI PCI bus which clears the
device_t associated with the corresponding ACPI handle in addition to
the normal PCI bus cleanup.
- Change cardbus_detach_card to call device_delete_children() and move
CardBus-specific delete logic into a new cardbus_child_deleted() method.
- Use device_delete_child() instead of pci_delete_child() in the SRIOV code.
- Add a bus_child_deleted method to the OpenFirmware PCI bus drivers which
frees the OpenFirmware device info for each PCI device.
Reviewed by: imp
Tested on: amd64 (CardBus and PCI-e hotplug)
Differential Revision: https://reviews.freebsd.org/D5831
OFW i2c probing requires a new method ofw_bus_get_node(), and the bus device is
assumed iichb. With these changes, i2c devices attached in fdt are probed and
attached automagically.
Import portions of the PowerPC OF PCI implementation into new file
"ofwpci.c", common for other platforms. The files ofw_pci.c and ofw_pci.h
from sys/powerpc/ofw no longer exist. All required declarations are moved
to sys/dev/ofw/ofwpci.h. This creates a new ofw_pci_write_ivar() function
and modifies some others methods. Most functions contain existing ppc
implementations in the majority unchanged. Now there is no need to have
multiple identical copies of methods for various architectures.
Requested by: jhibbits
Reviewed by: jhibbits, marius
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Differential Revision: https://reviews.freebsd.org/D4879
a DRIVER_MODULE() referencing mmc_driver has a MODULE_DEPEND() on mmc. This
is because the kernel linker only searches for symbols in dependent modules,
so loading sdhci_pci (and other bus-flavors of sdhci) would fail when mmc
was not compiled into the kernel (even if you hand-loaded mmc first).
(Thanks to jilles@ for providing the vital clue about the kernel linker.)
On some architectures, u_long isn't large enough for resource definitions.
Particularly, powerpc and arm allow 36-bit (or larger) physical addresses, but
type `long' is only 32-bit. This extends rman's resources to uintmax_t. With
this change, any resource can feasibly be placed anywhere in physical memory
(within the constraints of the driver).
Why uintmax_t and not something machine dependent, or uint64_t? Though it's
possible for uintmax_t to grow, it's highly unlikely it will become 128-bit on
32-bit architectures. 64-bit architectures should have plenty of RAM to absorb
the increase on resource sizes if and when this occurs, and the number of
resources on memory-constrained systems should be sufficiently small as to not
pose a drastic overhead. That being said, uintmax_t was chosen for source
clarity. If it's specified as uint64_t, all printf()-like calls would either
need casts to uintmax_t, or be littered with PRI*64 macros. Casts to uintmax_t
aren't horrible, but it would also bake into the API for
resource_list_print_type() either a hidden assumption that entries get cast to
uintmax_t for printing, or these calls would need the PRI*64 macros. Since
source code is meant to be read more often than written, I chose the clearest
path of simply using uintmax_t.
Tested on a PowerPC p5020-based board, which places all device resources in
0xfxxxxxxxx, and has 8GB RAM.
Regression tested on qemu-system-i386
Regression tested on qemu-system-mips (malta profile)
Tested PAE and devinfo on virtualbox (live CD)
Special thanks to bz for his testing on ARM.
Reviewed By: bz, jhb (previous)
Relnotes: Yes
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D4544
1) Include opt_platform.h to get QORIQ_DPAA. Otherwise the definition of
OCP85XX_TGTIF_LBC is incorrect.
2) The child resources are already allocated, just activate them, instead of
incorrectly remapping the memory regions (resource lists for lbc consist of the
virtual address of the child's resources, not the physical address).
Sponsored by: Alex Perez/Inertial Computing
Some MPC85xx GPIO controllers are compatible with QorIQ.
It may make more sense in the future to rename this and mpc85xx_gpio.c, as
mpc85xx_gpio.c appears to only be compatible with a few mpc85xx SoCs. All other
MPC85xx SoCs use the same controller as QorIQ.
Freescale's QorIQ line includes a new ethernet controller, based on their
Datapath Acceleration Architecture (DPAA). This uses a combination of a Frame
manager, Buffer manager, and Queue manager to improve performance across all
interfaces by being able to pass data directly between hardware acceleration
interfaces.
As part of this import, Freescale's Netcomm Software (ncsw) driver is imported.
This was an attempt by Freescale to create an OS-agnostic sub-driver for
managing the hardware, using shims to interface to the OS-specific APIs. This
work was abandoned, and Freescale's primary work is in the Linux driver (dual
BSD/GPL license). Hence, this was imported directly to sys/contrib, rather than
going through the vendor area. Going forward, FreeBSD-specific changes may be
made to the ncsw code, diverging from the upstream in potentially incompatible
ways. An alternative could be to import the Linux driver itself, using the
linuxKPI layer, as that would maintain parity with the vendor-maintained driver.
However, the Linux driver has not been evaluated for reliability yet, and may
have issues with the import, whereas the ncsw-based driver in this commit was
completed by Semihalf 4 years ago, and is very stable.
Other SoC modules based on DPAA, which could be added in the future:
* Security and Encryption engine (SEC4.x, SEC5.x)
* RAID engine
Additional work to be done:
* Implement polling mode
* Test vlan support
* Add support for the Pattern Matching Engine, which can do regular expression
matching on packets.
This driver has been tested on the P5020 QorIQ SoC. Others listed in the
dtsec(4) manual page are expected to work as the same DPAA engine is included in
all.
Obtained from: Semihalf
Relnotes: Yes
Sponsored by: Alex Perez/Inertial Computing
Summary:
Some drivers need special memory requirements. X86 solves this with a
pmap_change_attr() API, which DRM uses for changing the mapping of the GART and
other memory regions. Implement the same function for PowerPC. AIM currently
does not need this, but will in the future for DRM, so a default is added for
that, for business as usual. Book-E has some drivers coming down that do
require non-default memory coherency. In this case, the Datapath Acceleration
Architecture (DPAA) based ethernet controller has 2 regions for the buffer
portals: cache-inhibited, and cache-enabled. By default, device memory is
cache-inhibited. If the cache-enabled memory regions are mapped
cache-inhibited, an alignment exception is thrown on access.
Test Plan:
Tested with a new driver to be added after this (DPAA dTSEC ethernet driver).
No alignment exceptions thrown, driver works as expected with this.
Reviewed By: nwhitehorn
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5471
Extract common code from PowerPC's ofw_pci
Import portions of the PowerPC OF PCI implementation into
new file "ofw_pci.c", common for other platforms. The files ofw_pci.c and
ofw_pci.h from sys/powerpc/ofw no longer exist. All required declarations
are moved to sys/dev/ofw/ofw_pci.h.
This creates a new ofw_pci_write_ivar() function and modifies
ofw_pci_nranges(), ofw_pci_read_ivar(), ofw_pci_route_interrupt()
methods.
Most functions contain existing ppc implementations in the majority
unchanged. Now there is no need to have multiple identical copies
of methods for various architectures.
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Reviewed by: jhibbits, mmel
Differential Revision: https://reviews.freebsd.org/D4879
This needs to return to the drawing board as it breaks both
PowerPC and Sparc64 build.
Pointed out by: jhibbits
This simplifies checking for default resource range for bus_alloc_resource(),
and improves readability.
This is part of, and related to, the migration of rman_res_t from u_long to
uintmax_t.
Discussed with: jhb
Suggested by: marcel
Import portions of the PowerPC OF PCI implementation into
new file "ofw_pci.c", common for other platforms. The files ofw_pci.c and
ofw_pci.h from sys/powerpc/ofw no longer exist. All required declarations
are moved to sys/dev/ofw/ofw_pci.h.
This creates a new ofw_pci_write_ivar() function and modifies
ofw_pci_nranges(), ofw_pci_read_ivar(), ofw_pci_route_interrupt() methods.
Most functions contain existing ppc implementations in the majority
unchanged. Now there is no need to have multiple identical copies
of methods for various architectures.
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Reviewed by: jhibbits, mmel
Differential Revision: https://reviews.freebsd.org/D4879
Provide bus_get_bus_tag() for sparc64, powerpc, arm, arm64 and mips
nexus and its children in order to return a platform specific default tag.
This is required to ensure generic correctness of the bus_space tag.
It is especially needed for arches where child bus tag does not match
the parent bus tag. This solves the problem with ppc architecture
where the PCI bus tag differs from parent bus tag which is big-endian.
This commit is a part of the following patch:
https://reviews.freebsd.org/D4879
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Reviewed by: jhibbits, mmel
Differential Revision: https://reviews.freebsd.org/D4879
will allow for code that uses the old fdt_get_range and fdt_regsize
functions to find a range, map it, access, then unmap to replace this, up
to and including the map, with a call to OF_decode_addr.
As this function should only be used in the early boot code the unmap is
mostly do document we no longer need the mapping as it's a no-op, at least
on arm.
Reviewed by: jhibbits
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5258
ucontext_t available. Our code even has XXX comment about this.
Add a bit of compliance by moving struct __ucontext definition into
sys/_ucontext.h and including it into signal.h and sys/ucontext.h.
Several machine/ucontext.h headers were changed to use namespace-safe
types (like uint64_t->__uint64_t) to not depend on sys/types.h.
struct __stack_t from sys/signal.h is made always visible in private
namespace to satisfy sys/_ucontext.h requirements.
Apparently mips _types.h pollutes global namespace with f_register_t
type definition. This commit does not try to fix the issue.
PR: 207079
Reported and tested by: Ting-Wei Lan <lantw44@gmail.com>
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Summary:
The revised Book-E spec, adding the specification for the MMUv2 and e6500,
includes a hardware PTE layout for indirect page tables. In order to support
this in the future, migrate the PTE format to match the MMUv2 hardware PTE
format.
Test Plan: Boot tested on a P5020 board. Booted to multiuser mode.
Differential Revision: https://reviews.freebsd.org/D5224
ABI of struct fpreg. The FPU emulator operates on the "raw" FPU state
stored in the pcb rather than the "cooked" fpreg state used for ptrace()
and cores.
Reported by: bz
The stack must be aligned to 16 bytes at all times. Clang 3.8 is especially
adamant about this, and causes strange behavior and segmentation faults if it is
not the case.
PR: kern/206810
Device trees mark lbc as compatible with simplebus. Since simplebus is passed
first, it attaches first. When lbc's pass (default pass) comes, the bus is
already attached to simplebus, so is skipped.
Sponsored by: Alex Perez/Inertial Computing
The PT_{GET,SET}FPREGS requests use 'struct fpreg' and the NT_FPREGSET
core note stores a copy of 'struct fpreg'. As with x86 and the floating
point state there compared to the extended state in XSAVE, struct fpreg
on powerpc now only holds the 'base' FP state, and setting it via
PT_SETFPREGS leaves the extended vector state in a thread unchanged.
Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D5004
Use driver settable callbacks for handling of:
- core post reset
- reading actual port speed
Typically, OTG enabled EHCI cores wants setting of USBMODE register,
but this register is not defined in EHCI specification and different
cores can have it on different offset.
Also, for cores with TT extension, actual port speed must be determinable.
But again, EHCI specification not covers this so this patch provides
function for two most common variant of speed bits layout.
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D5088
POSIX requires these members to be of type void * rather than the
char * inherited from 4BSD. NetBSD and OpenBSD both changed their
fields to void * back in 1998. No new build failures were reported
via an exp-run.
PR: 206503 (exp-run)
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D5092
Summary:
Migrate to using the semi-opaque type rman_res_t to specify rman resources. For
now, this is still compatible with u_long.
This is step one in migrating rman to use uintmax_t for resources instead of
u_long.
Going forward, this could feasibly be used to specify architecture-specific
definitions of resource ranges, rather than baking a specific integer type into
the API.
This change has been broken out to facilitate MFC'ing drivers back to 10 without
breaking ABI.
Reviewed By: jhb
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5075
The only difference between dcbzl and dcbz is dcbzl operates on native cache
line lengths regardless of L1CSR0[DCBZ32]. Since we don't change the cache line
size, the cacheline_size variable will reflect the used cache line length, and
dcbz will work as expected.
By confining the page table management to a handful of functions it'll be
easier to modify the page table scheme without affecting other functions.
This will be necessary when 64-bit support is added, and page tables become
much larger.
VM_MAX_KERNEL_ADDERESS is the maximum KVA address. 0xf8000000 is the start of
device mapping space. Since several conditional checks use '<=' against
VM_MAX_KERNEL_ADDRESS, bad things could feasibly happen.
On powerpc64, pointers are 64 bits, so casting from uint32_t changes the integer
width.
The alternative was to use register_t, but I didn't see register_t used as
argument type for any other functions, though didn't look too closely. u_long
was an acceptable alternative. On 64-bit it's 64 bits, on 32-bit it's 32 bits.
powerpc_init() initializes the mmu. Since this may clear pages via
pmap_zero_page(), set the cacheline size before calling into it, so
pmap_zero_page() has the right cacheline size. This isn't completely
necessary now, but will be when 64-bit book-e is completed.
For rs6000, most memory insns and addi/addis do not allow GPR0 for RA
(they use literal zero there instead). So use a 'b' constraint to make
sure to have a base register other than GPR0.
GCC-4.7 and up handles this with allocating r9 instead of r0.
providing compiled-in static environment data that is used instead of any
data passed in from a boot loader.
Previously 'env' worked only on i386 and arm xscale systems, because it
required the MD startup code to examine the global envmode variable and
decide whether to use static_env or an environment obtained from the boot
loader, and set the global kern_envp accordingly. Most startup code wasn't
doing so. Making things even more complex, some mips startup code uses an
alternate scheme that involves calling init_static_kenv() to pass an empty
buffer and its size, then uses a series of kern_setenv() calls to populate
that buffer.
Now all MD startup code calls init_static_kenv(), and that routine provides
a single point where envmode is checked and the decision is made whether to
use the compiled-in static_kenv or the values provided by the MD code.
The routine also continues to serve its original purpose for mips; if a
non-zero buffer size is passed the routine installs the empty buffer ready
to accept kern_setenv() values. Now if the size is zero, the provided buffer
full of existing env data is installed. A NULL pointer can be passed if the
boot loader provides no env data; this allows the static env to be installed
if envmode is set to do so.
Most of the work here is a near-mechanical change to call the init function
instead of directly setting kern_envp. A notable exception is in xen/pv.c;
that code was originally installing a buffer full of preformatted env data
along with its non-zero size (like mips code does), which would have allowed
kern_setenv() calls to wipe out the preformatted data. Now it passes a zero
for the size so that the buffer of data it installs is treated as
non-writeable.
LBC block size can only be up to 4GB. The existing code already clamps it, but
mixes unsigned long and uint32_t. This works on 32-bit targets, but not 64-bit,
so isn't completely correct. This fixes the type confusion.
Newer Book-E cores (e500mc, e5500, e6500) do not support the WE bit in the MSR,
and instead delegate CPU idling to the SoC.
Perhaps in the future the QORIQ_DPAA option for the mpc85xx platform will become
a subclass, which will eliminate most of the #ifdef's.
This includes the following changes:
* SMP kickoff for QorIQ (tested on P5020)
* Errata fixes for some silicon revisions
* Enables L2 (and L3 if available) caches
Obtained from: Semihalf
Sponsored by: Alex Perez/Inertial Computing
There's no need for it to be in asm. Also, by writing in C, and marking it
static in pmap.c, it saves a branch to the function itself, as it's only used in
one location. The generated asm is virtually identical to the handwritten code.
Summary:
With some additional changes for AIM, that could also support much
larger physmem sizes. Given that 32-bit AIM is more or less obsolete, though,
it's not worth it at this time.
Differential Revision: https://reviews.freebsd.org/D4345
