a gpio pin. If neither of the options is specified, pre-set the pin's
output value to the pin's current input value, to achieve glitch-free
transitions to output mode on pins that are pulled up or down at reset
or via fdt pinctrl data.
mode or not. An earlier attempt to make this work was done in r320456, by
always reading the pad status register (PSR) instead of the data register.
But it turns out the values in PSR only reflect the electrical level of an
output pin if the pad is configured with the SION (Set Input On) bit in the
pinmux config, and most output gpio pads are not configured that way.
So now a gpio read is done by returning the value from the data register,
which works right whether the pin is configured for input or output, unless
the pin has been set for OPENDRAIN mode, in which case the PSR is read
instead. For this to work, the pin must also be configured with SION turned
on in the fdt pinmux data, which is a reasonable thing to require for the
unusual case of reading an open-drain output pin.
Include source files and drivers for Marvell ArmadaXP and Armada38X
in GENERIC kernel config.
Submitted by: Michal Mazur <mkm@semihalf.com>
Rafal Kozik <rk@semihalf.com>
Reviewed by: manu
Tested by: manu
Obtained from: Semihalf
Sponsored by: Stormshield
Marvell SoC identification function was called by SYSINIT on all armv7
platforms, which brakes platforms other than Marvell built with
GENERIC config. Fix this by shifting SoC identifying to Marvell platform
initialization.
Submitted by: Patryk Duda <pdk@semihalf.com>
Reviewed by: manu
Tested by: manu
Obtained from: Semihalf
Sponsored by: Stormshield
r332839 changed number of cells per interrupt for local_intc from 1 to 2
to pass type of IRQ. Driver expected only 1 cell so after r332839
all interrupt children of local_intc failed to allocate IRQ resource.
Fix this regression by relaxing check for number of cells in interrupt
property to be either 1 or 2.
PR: 227904
Dumpers may wish to print messages from an initialization hook; this
change ensures that such messages aren't mixed with output from the
generic dump code.
MFC after: 1 week
always use 'M. Warner Losh' for consistency.
'All Rights Reserved.' was prescribed by the Buenos Aires Copyright
Convention of 1910, but has been mostly dead since the early 1990's
and completely meaningless since 2000 when Nicaragua ratified the
Berne convention.
Some files not done due to ambiguity of various types.
Move the allwinner early printf support to the snps driver as it
should work with all implementation.
While here add instruction for enabling it on 64bits SoCs.
Name each ehci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ehci from kernel; already loaded from kernel
Name each ahci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ahci from kernel; already loaded from kernel
WHile gate_shift was present in the NM_CLK macro it wasn't set into the
clock definition structure resulting in NM clocks not being correctly
gated when they should.
If the module wasn't enabled by the bootloader it will have stayed ungated.
Switch test between zero based factor and power of two one.
This resulted in a miscalculation of the factor if it was a power
of two one.
Some clocks frequencies were not calculated correctly because of that.
This patch adds support for gpio and gpioled into ARMADA38X kernel
config.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14758
This patch replaces in-driver FDT parsing, which was
needed for setting initial values on GPIO pins.
Now FDT is parsed by generic kernel code, pins are set
by invoking gpio_map_gpios method.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14757
This patch implements and exports functions described
in gpio_if.m file. It also uses new gpiobus_attach_bus function
instead of adding gpioc and gpiobus as children. It removes
ulgy reading SoC ID and related if..else, so it depends only on
data read from FDT.
Submitted by: Patryk Duda <pdk@semihalf.com>
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14756
- Add an implementation of atomic_fcmpset_32() using RAS for armv4/v5.
This fixes recent world breakage due to use of atomic_fcmpset() in
userland.
- While here, be more careful to not expose wrapper macros for 64-bit
atomic_*cmpset to userland for armv4/v5 as only 32-bit cmpset is
implemented.
This has been reviewed, but not runtime-tested, but should fix the arm.arm
and arm.armeb worlds that have been broken for a while.
Reviewed by: imp
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D15147
The return value of atomic_cmpset() and atomic_fcmpset() is an int (which
is really a bool) that has the values 0 or 1. Some of the inlines were
using the type being operated on (e.g. uint32_t) as either the return type
of the function, or the type of a local 'ret' variable used to hold the
return value. Fix all of these to just use plain 'int'. Due to C promotion
rules and the fact that the value can only be 0 or 1, these should all be
harmless.
Reviewed by: imp (only the v4 ones)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D15147
Half of implementations always failed (returned (-1)) and they were
previously used in only one place.
Reviewed by: kib, andrew
Obtained from: CheriBSD
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D15102
Also remove the commented out documentation. The documentation arrived
with the import of the copy.9 manpage. I suspect the implementations
came from NetBSD while bootstrapping the Arm and MIPS ports.
Reviewed by: andrew, jmallett
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D15108
Switch to standard FDT-base driver behavior and don't attach
if node "status" property value nn DTS is not set to "okay"
On RPi PWM by default is disabled, to enable it pwm.dtbo
from official repo[1] should be copied to overlays directory
on SD card FAT partition and "dtoverlay=pwm" line added to
config.txt. For more details see pwm overlay documentation[2]
sysutils/rpi-firmware port now includes overlays, so they
can be installed as a part of release image build.
[1] https://github.com/raspberrypi/firmware/tree/master/boot
[2] https://github.com/raspberrypi/firmware/blob/master/boot/overlays/README
No objections from: phk@
Linux device tree binding, whose usage is obligatory,
comprises faulty representation of Marvell cryptographic
engine (CESA) - two engines are artificially gathered into
single DT node, in order to avoid certain SW limitation.
This patch improves the cesa driver to support above binding,
depending on compatible string, which helps to ensure
backward compatibility.
Submitted by: Patryk Duda
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14760
Change OF_getencprop_alloc semantics to be combination of malloc and
OF_getencprop and return size of the property, not number of elements
allocated.
For the use cases where number of elements is preferred introduce
OF_getencprop_alloc_multi helper function that copies semantics
of OF_getencprop_alloc prior to this change.
This is to make OF_getencprop_alloc and OF_getencprop_alloc_multi
function signatures consistent with OF_getencprop_alloc and
OF_getencprop_alloc_multi.
Functionality-wise this patch is mostly rename of OF_getencprop_alloc
to OF_getencprop_alloc_multi except two calls in ofw_bus_setup_iinfo
where 1 was used as a block size.
Split out delay parsing into a separate function; we'll support both
{tx,rx}-delay as well as the new versions.
While here, validate that they're within the expected range and fail to
attach if they are not. Assuming that we can clamp the delay is a bad idea
that might result in a non-working awg anyways, so we'll fail early to make
it easier to catch.
This version also unsets the tx and rx delay registers unconditionally and
then sets them if we read a non-zero delay. These delay properties should
default to 0 if not specified, as declared in the binding documentation.
Presumably the delays will be set via hardware configuration if they're not
explicitly set in FDT.
OF_getprop_alloc takes element size argument and returns number of
elements in the property. There are valid use cases for such behavior
but mostly API consumers pass 1 as element size to get string
properties. What API users would expect from OF_getprop_alloc is to be
a combination of malloc + OF_getprop with the same semantic of return
value. This patch modifies API signature to match these expectations.
For the valid use cases with element size != 1 and to reduce
modification scope new OF_getprop_alloc_multi function has been
introduced that behaves the same way OF_getprop_alloc behaved prior to
this patch.
Reviewed by: ian, manu
Differential Revision: https://reviews.freebsd.org/D14850
On Raspberry Pi platform GPIO controller also responsible for pins
multiplexing. Pi code predates proper FDT support in FreeBSD so a
lot of pinmux info is hardcoded. This patch:
- Implements pinctl methods in bcm2835_gpio
- Converts all devices with ad-hoc pinmux info to proper pin control
mechanisms and adds pinmux info in FreeBSD's custom dts files.
- Adds fdt_pinctrl option to RPI2 and RPI-B kernels
- Adds SPI pinmux config to FreeBSD's customization of GNU DTS.
Reviewed by: imp, manu
Differential Revision: https://reviews.freebsd.org/D14104
If a regulator is missing a mandatory property (like 'regulator-name'), do
not fail, regulator_parse_ofw_stdparam is returning a non-zero value so just
skip this regulator.
Also if any regulator fails to attach continue with the rest of the regulators
instead of returning ENXIO in axp8xx_attach
Tested On: BananaPi M3
opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
It was later found that some operation on the OrangePi one will cause
direct accesses to the eeprom to return wrong data again, so reading it all
once via prctl at attach time is no longer sufficient.
This patch moves all global data structures into mv_gpio_softc,
and puts device_t parameter to functions calls everywhere where needed.
As a result, we can create multiple driver instances.
Removed names in function declaration to keep style.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14755
This patch adds support for more than one interrupts
in GPIO controller. It reads necessary information (such as cell size)
from FDT, so there are no magic numbers.
Note that interrupts are still not working, but this patch makes
one good step in correct direction
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14754
This patch introduces gpio debouncing mechanism
with fixed memory allocation in critical section.
When you press button, value at gpio pin connected to button
is changing many times which will cause in unexpected behaviour.
Debouncing mechanism will prevent this phenomenon
Submitted by: Patryk Duda <pdk@semihalf.com>
Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14753
If driver cannot determine ranges based on fdt, it will calculate
them based on number and type of current port.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14752
Ranges in pcie-controller are unused, so could be changed to match Linux
device tree represntation. Same with interrupt-cells and interrupt-parent.
In PCI controller driver ocd_data are used for matching driver and
choose proper resources acquisition function.
fdt_win_process_child have new argument which provide information
about fdt node containing addresses of MMIO registers.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: manu [DT part]
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14751
In Linux FDT pcie does not have compatible string.
Configuration of windows in mv_common was based on fdt compatible.
Now pcie windows are configured by their parent: pcie_controller.
Processing is moved to fdt_win_process_child. fdt_win_process now
only walk through the tree. SOC_NODE_PCI is position of pcie function in
soc_node_spec array.
PCIe probe cannot use ofw_bus_search_compatible, because it needs to
check also device type and parents compatible.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: manu [DT part]
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14749
GENERIC ARM config use NEW_PCIB driver (https://wiki.freebsd.org/NEW_PCIB).
To satisfy it, allocation and deallocation of PCI_RES_BUS is necessary.
Conditional compilation is added for backward compatibility with ARMv5
configs.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: jhb
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14748
Define timers registers for both SoCs and choose proper one during runtime
based on information from FDT.
In WDT driver there are different function for ArmadaXP and other ARMv5 SoCs.
In timer driver registers definitions are stored in resource_spec structure
and chosen during runtime.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14746
Define reset registers for both Armada38X and ArmadaXP and
choose proper one during runtime based on information from FDT.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14745
Spliting armv5 and armv7 machdep is necessary for adding Armada38X and
ArmadaXP to GENERIC config.
PLATFORM framework checks SOC type in FDT and will select proper
initialization function implementation during runtime.
Pointers to SoC specific implementation are stored in array of
platform_method_t and provided to framework by FDT_PLATFORM_DEF macro.
PLATFORM framework supports also reset function. To simplify implementation
cpu_reset is moved from mv_common to armv5 and armv7 machdep.
Armada38X and ArmadaXP share now common list of files, so resolve all
dependencies as well.
Submitted by: Rafal Kozik <rk@semihalf.com>
Marcin Wojtas <mw@semihalf.com>
Reviewed by: mw
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14744
Two modules with the same name cannot be loaded, so Marvell specific drivers
cannot have the same name as the generic drivers.
Files with the same name, even in different folders overlaps their .o files,
so in order to prepare for supporting Marvell platforms in GENERIC armv7
config, modify conflicting names.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14743
The PLATFORM code will perform the software loop in the early boot,
so extract the actual delay code to handle situation, when
the timers are already initialized.
Obtained from: Semihalf
Sponsored by: Stormshield
Store pointers to SoC specific functions in mv_timer_config structure
and determine proper config in runtime based on compatible string from FDT.
Compatible string for ArmadaXP timers is changed to match Linux FDT.
Armada 38x uses generic Cortex-A9 timer and separate watchdog drivers, so
it does not need to be supported by timer driver.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: manu
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14741
In GENERIC kernel choosing proper get_tclk and get_cpu_freq implementation must
be done in runtime. Kernel for both SoC need to have implementation of each
other functions, so common file list mv/files.arm7 is added.
Marvell armv5 SoC have their own non-generic implementation of those function.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14739
Preparation for adding Armada38X and ArmadaXP SoC to GENERIC config.
Supported platform are listed in soc_family enum.
struct decode_win_spec contains platform specific functions and constants.
Function mv_check_soc_family checks SoC type and chooses proper structure
in runtime, as well as platform-dependent functions.
Unnecessary dummy functions are removed.
Because of changing registers name to more generic new definition of
FDT_DEVMAP_MAX in mv_machdep is added.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14738
Validate only drivers used by given platform.
Pointers to validation function
are added to soc_node_spec structure.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14737
get_sar_value is implemented only for ArmadaXP and Armada38X. Splitting it for
two different functions and change registers names result in more generic code.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14736
PCI ports differ between Marvell SoCs, but have the same compatible in FDT.
Identification is made based on parent compatible during attach.
For ArmadaXP skipping enable procedure is necessary. To achieve it
sc_skip_enable_procedure flag is used.
For Armada38x find root procedure is necessary. For other SoCs root link is
always at slot 0. sc_enable_find_root_slot flag is used to select proper
behaviour.
Marvell armv5 platforms does not support msi.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14735
Defining INTRNG remove some necessary registers and declarations of
pic_init_secondary, pic_ipi_send, pic_ipi_read and pic_ipi_clear.
Because Marvell ArmadaXP and Armada38X always use INTRNG, include all
INTRNG code and remove code that does not use it.
Separate pic registers declarations for Armada38X are unnecessary, it
works properly with ArmadaXP config.
Submitted by: Rafal Kozik <rk@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14734
The Zynq/Zedboard GPIO driver attempts to tri-state all GPIO pins on
boot up but the order in which I reset the hardware can cause the pins
to be briefly held low before being tri-stated. This is a problem on
boards that use GPIO pins to reset devices.
In particular, the Zybo and ZC-706 boards use a GPIO pin as a USB PHY
reset. If U-boot enables the USB port before booting the kernel, the
GPIO driver attach causes a glitch on the USB PHY reset and the USB
port loses power. My fix is to have the GPIO driver leave the pins in
whatever configuration U-boot placed them.
PR: 225713
Submitted by: Thomas Skibo <thoma555-bsd@yahoo.com>
MFC after: 1 week
DTB Overlays are useful to change/add nodes to a dtb without the need to
modify it.
Add support for building dtbo during buildkernel.
The goal of DTBO present in the FreeBSD source tree is to fill a gap in
time when we submit changes upstream (Linux). Instead of waiting 2 to 4 months
we can add a DTBO in tree in the meantime.
This is not for adding DTBO for capes/hat/addon boards, those will be
better to put in a ports.
This is also not for enabling a i2c/spi/pwm controller on certain pins,
each user have a different use case for those (which pins to use etc ...)
and we cannot have all possible configuration.
Add a dtbo for sun8i-h3-sid which add the SID node missing in upstream dts.
Reviewed by: kevans
Differential Revision: https://reviews.freebsd.org/D14782
assym is only to be included by other .s files, and should never
actually be assembled by itself.
Reviewed by: imp, bdrewery (earlier)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D14180
OF_finddevices returns ((phandle_t)-1) in case of failure. Some code
in existing drivers checked return value to be equal to 0 or
less/equal to 0 which is also wrong because phandle_t is unsigned
type. Most of these checks were for negative cases that were never
triggered so trhere was no impact on functionality.
Reviewed by: nwhitehorn
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D14645
Upstream DTBs don't provide IRQ lines for the RNG. Moreover, harvesting
bytes as often as the RNG interrupt is triggered (87 times per sec) is an
overkill.
For these reasons, get rid of the interrupt mode and make callout mode the
default, with random bits harvested every 4 seconds.
Submitted by: Sylvain Garrigues <sylgar@gmail.com>
Reviewed by: ian, imp, manu, mmel
Approved by: emaste
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D14541
vbus-supply properties may be specified for each PHY. These properties
reference a regulator that we must turn on/off as we turn the PHY on/off.
However, if the usbphy comes up before the regulator in question (as is the
case with GPIO-controlled regulators), then we will fail to grab a handle to
the regulator and control it as the PHY power state changes.
Fix it by just attaching the usbphy driver later. We don't really need it at
RESOURCE, we just need it to be before DEFAULT when ehci/ohci attach. In
particular, this fixes the USB NIC on a board that we don't yet supported-
without this, it will not power on and if_ure cannot attach.
Tested on: various boards [manu]
Tested on: OrangePi R1 [Rap2 (irc)]
Reported by: Rap2 (irc, "Cannot find USB NIC")
correctly for the data contained on each memory page.
There are several components to this change:
* Add a variable to indicate the start of the R/W portion of the
initial memory.
* Stop detecting NX bit support for each AP. Instead, use the value
from the BSP and, if supported, activate the feature on the other
APs just before loading the correct page table. (Functionally, we
already assume that the BSP and all APs had the same support or
lack of support for the NX bit.)
* Set the RW and NX bits correctly for the kernel text, data, and
BSS (subject to some caveats below).
* Ensure DDB can write to memory when necessary (such as to set a
breakpoint).
* Ensure GDB can write to memory when necessary (such as to set a
breakpoint). For this purpose, add new MD functions gdb_begin_write()
and gdb_end_write() which the GDB support code can call before and
after writing to memory.
This change is not comprehensive:
* It doesn't do anything to protect modules.
* It doesn't do anything for kernel memory allocated after the kernel
starts running.
* In order to avoid excessive memory inefficiency, it may let multiple
types of data share a 2M page, and assigns the most permissions
needed for data on that page.
Reviewed by: jhb, kib
Discussed with: emaste
MFC after: 2 weeks
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D14282
Pretty much any other device might need to manipulate a gpio pin during its
probe or attach routines, so these devices must be available as early as
possible.
The gpio device is an interrupt controller, but I didn't choose the
INTERRUPT pass for that reason (it works fine as an interrupt controller as
long as it attaches any time before interrupts are enabled). That just
looked like the right place in the passes to ensure that it attaches before
any type of device that might need gpio pin manipulations.
driver requires interrupts to do transfers, and the drivers for the SPI
devices on the bus quite reasonably expect to be able to do IO while probing
and attaching.
It would have been on an actual named pass before, but none were really
appropriate in name. Move it to the recently created SUPPORTDEV pass, which
perfectly describes it and keeps it in the right order.
Getting regulator is good, enabling them is better.
When the mmc stack decide to change the voltage for IO, don't
change the main vcc of the sd/mmc, only the io vcc.
AXP803 and AXP813/818 are very similar, only two regulators differs.
AXP803 is the companion chip for A64/R18
AXP813 is the companion chip for A83T
AXP818 is the companion chip for H8 (~A83T)
Add support for all regulators found in both of them.
to what other arches (all except riscv and armv4/5) do.
Submitted by: Hyun Hwang <hyun@caffeinated.codes>
Differential Revision: https://reviews.freebsd.org/D14465
(using "boot -d" at the loader propmt or setting boot_ddb in loader.conf).
Submitted by: Thomas Skibo <thomasskibo@yahoo.com>
Differential Revision: https://reviews.freebsd.org/D14428
We don't support float in the boot loaders, so don't include
interfaces for float or double in systems headers. In addition, take
the unusual step of spiking double and float to prevent any more
accidental seepage.
Make vm_wait() take the vm_object argument which specifies the domain
set to wait for the min condition pass. If there is no object
associated with the wait, use curthread' policy domainset. The
mechanics of the wait in vm_wait() and vm_wait_domain() is supplied by
the new helper vm_wait_doms(), which directly takes the bitmask of the
domains to wait for passing min condition.
Eliminate pagedaemon_wait(). vm_domain_clear() handles the same
operations.
Eliminate VM_WAIT and VM_WAITPFAULT macros, the direct functions calls
are enough.
Eliminate several control state variables from vm_domain, unneeded
after the vm_wait() conversion.
Scetched and reviewed by: jeff
Tested by: pho
Sponsored by: The FreeBSD Foundation, Mellanox Technologies
Differential revision: https://reviews.freebsd.org/D14384
This adds sys/modules/imx with a SUBDIR makefile to make the whole
collection of modules that are specific to these SoCs. Initially, that
"whole collection" consists of the if_ffec and imx_i2c drivers.
The if_ffec driver is referenced in its existing home in ../ffec rather
than moving it into the imx directory, because it's used by powerpc too,
but it is no longer built for all armv6/7 systems.
The imx_i2c driver is newly added as a module.
appears that node names no longer include leading zeroes in the @address
qualifiers, so we have to search for the nodes involved in interrupt fixup
using both flavors of name to be compatible with old and new .dtb files.
(You know you're in a bad place when you're applying a workaround to code
that exists only as a workaround for another problem.)
The FDT variant is called "gicv2m" too, and as both would try to register
on gic, only one of them would succeed, while we want them both in a
GENERIC kernel.
Reviewed by: andrew
significant source of cache line contention from vm_page_alloc(). Use
accessors and vm_page_unwire_noq() so that the mechanism can be easily
changed in the future.
Reviewed by: markj
Discussed with: kib, glebius
Tested by: pho (earlier version)
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D14273
Remove most of the Atmel at91 boards. Most of them are no longer
relevant or used by people. Kept ATMEL since it should work on all the
boards that still work (I've not confirmed this, since I don't have
all these boards). Also kept SAM9G20EK, since I have several boards
that it is used on. If I've deleted a kernel in error, please let me
know.
On the OrangePi One at least, emac reset when an ethernet cable is not
plugged in seems to break ethernet. Soft reset will fail, even with
increasing the delay and retries to wait for up to 20 seconds. This can be
reproduced across at least two different OrangePi One's by simply leaving
ethernet cable unplugged when awg attaches. Whether it's plugged in or not
through u-boot process makes no difference.
Skipping the reset in this configuration doesn't seem to cause any problems,
tried across many many reboots with and without ethernet cable plugged in.
Tested on: OrangePi One
Tested on: Other boards (manu)
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D13974
global to per-domain state. Protect reservations with the free lock
from the domain that they belong to. Refactor to make vm domains more
of a first class object.
Reviewed by: markj, kib, gallatin
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D14000
Similarly as we already do for arm64, for mitigation is necessary to
flush branch predictor when we:
- do task switch
- receive prefetch abort on non-userspace address
The user can disable this mitigation by setting 'machdep.disable_bp_hardening'
sysctl variable, or it can check actual system status by reading
'machdep.spectre_v2_safe'
The situation is complicated by fact that:
- for Cortex-A8, the BPIALL instruction is effectively NOP until the IBE bit
in ACTLR is set.
- for Cortex-A15, the BPIALL is always NOP. The branch predictor can be
only flushed by doing ICIALLU with special bit (Enable invalidates of BTB)
set in ACTLR.
Since access to the ACTLR register is locked to secure monitor/firmware on
most boards, they will also need update of firmware / U-boot.
In worst case, when secure monitor is on-chip ROM (e.g. PandaBoard),
the board is unfixable.
MFC after: 2 weeks
Reviewed by: imp, emaste
Differential Revision: https://reviews.freebsd.org/D13931
the "power down" watchdog used by the ROM boot code is still active when the
regular watchdog is activated, turn off the power-down watchdog.
This adds support for the "fsl,ext-reset-output" FDT property. When
present, that property indicates that a chip reset is accomplished by
asserting the WDOG1_B external signal, which is supposed to trigger some
external component such as a PMIC to ready the hardware for reset (for
example, adjusting voltages from idle to full-power levels), and assert the
POR signal to SoC when ready. To guard against misconfiguation leading to a
non-rebootable system, the external reset signal is backstopped by code
that asserts a normal internal chip reset if nothing responds to the
external reset signal within one second.
bottom of the file, where it is in most imx5/6 drivers. Switch from an RD2
macro using bus_space_read_2() to an inline function using bus_read_2();
likewise for WR2. Use RESOURCE_SPEC_END to end the resource_spec list.
Net effect should be no functional changes.
instead of frobbing the registers directly.
As a hack the bcm2835_pwm kmod presently ignores the 'status="disabled"'
in the RPI3 DTB, assuming that if you load the kld you probably
want the PWM to work.
Uses of mallocarray(9).
The use of mallocarray(9) has rocketed the required swap to build FreeBSD.
This is likely caused by the allocation size attributes which put extra pressure
on the compiler.
Given that most of these checks are superfluous we have to choose better
where to use mallocarray(9). We still have more uses of mallocarray(9) but
hopefully this is enough to bring swap usage to a reasonable level.
Reported by: wosch
PR: 225197
Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
functionality on Raspberry Pi 0.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D13924
(i386 and arm) that never implement them. This allows the removal of
#ifdef PHYS_TO_DMAP on code otherwise protected by a runtime check on
PMAP_HAS_DMAP. It also fixes the build on ARM and i386 after I forgot an
#ifdef in r328168.
Reported by: Milan Obuch
Pointy hat to: me
kernel by PHYS_TO_DMAP() as previously present on amd64, arm64, riscv, and
powerpc64. This introduces a new MI macro (PMAP_HAS_DMAP) that can be
evaluated at runtime to determine if the architecture has a direct map;
if it does not (or does) unconditionally and PMAP_HAS_DMAP is either 0 or
1, the compiler can remove the conditional logic.
As part of this, implement PHYS_TO_DMAP() on sparc64 and mips64, which had
similar things but spelled differently. 32-bit MIPS has a partial direct-map
that maps poorly to this concept and is unchanged.
Reviewed by: kib
Suggestions from: marius, alc, kib
Runtime tested on: amd64, powerpc64, powerpc, mips64
Focus on code where we are doing multiplications within malloc(9). None of
these ire likely to overflow, however the change is still useful as some
static checkers can benefit from the allocation attributes we use for
mallocarray.
This initial sweep only covers malloc(9) calls with M_NOWAIT. No good
reason but I started doing the changes before r327796 and at that time it
was convenient to make sure the sorrounding code could handle NULL values.
X-Differential revision: https://reviews.freebsd.org/D13837
- Add a per compatible configuration struct
- Not all SoC uses the same size for DMA transfert, add this into the
configuration data
- Use new timing mode for some SoC (A64 mmc)
- Auto calibrate clock for A64 mmc/emmc
- A64 mmc controller need masking of data0
- Add support for vmmc/vqmmc regulator
- Add more capabilities, r/w speed is better for eMMC
- MMC_CAP_SIGNALING_180 gives weird result so do not enable it for now.
- Add new register documented in H3/A64 user manual
Tested-On: Pine64-LTS (A64), eMMC still doesn't work
Tested-On: A64-Olinuxino (A64), sd and eMMC are working
Tested-On: NanoPi Neo Plus2 (H5), sd and eMMC are working
Tested-On: OrangePi PC2 (H5), sd only (no eMMC)
Tested-On: OrangePi One (H3), sd only (no eMMC)
Tested-On: BananaPi M2 (A31s), sd only (no eMMC)
Attaching syscon_generic earlier than BUS_PASS_DEFAULT makes it more
difficult for specific syscon drivers to attach to the syscon node and to
get ordering right. Further discussion yielded the following set of
decisions:
- Move syscon_generic to BUS_PASS_DEFAULT
- If a platform needs a syscon with different attach order or probe
behavior, it should subclass syscon_generic and match on the SoC specific
compat string
- When we come across a need for a syscon that attaches earlier but only
specifies compatible = "syscon", we should create a syscon_exclusive driver
that provides generic access but probes earlier and only matches if "syscon"
is the only compatible. Such fdt nodes do exist in the wild right now, but
we don't really use them at the moment.
Additionally:
- Any syscon provider that has needs any more complex than a spinlock solely
for syscon access and a single memory resource should subclass syscon
directly rather than attempting to subclass syscon_generic or add complexity
to it. syscon_generic's attach/detach methods may be made public should the
need arise to subclass it with additional attach/detach behavior.
We introduce aw_syscon(4) that just subclasses syscon_generic but probes
earlier to meet our requirements for if_awg and implements #2 above for this
specific situation. It currently only matches a64/a83t/h3 since these are
the only platforms that really need it at the time being.
Discussed with: ian
Reviewed by: manu, andrew, bcr (manpages, content unchanged since review)
Differential Revision: https://reviews.freebsd.org/D13793
allocated with a tag to come from the specified domain if it meets the
other constraints provided by the tag. Automatically create a tag at
the root of each bus specifying the domain local to that bus if
available.
Reviewed by: jhb, kib
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D13545
userspace to control NUMA policy administratively and programmatically.
Implement domainset based iterators in the page layer.
Remove the now legacy numa_* syscalls.
Cleanup some header polution created by having seq.h in proc.h.
Reviewed by: markj, kib
Discussed with: alc
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D13403
Although these should have been 'emac', upstream DTS is going with using
'gmac' as the function name for the emac RGMII pins. Rename here to
accommodate.
emac support for the a83t should come in with the 4.16 DTS update, in
another couple of months.
For each we need to walk the MADT to find which we have, then add the
driver as needed. As each may have a child they will each walk the same
table to find these details.
Reviewed by: mmel
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8720
This adds a new acpi_bus interface with a map_intr method. This is similar
to the Open Firmware map_intr method and allows us to create the needed
mapping from ACPI space to INTRNG space.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8617
Highlights of the new bindings:
- ahb clock is specified as 'stmmaceth'
- The PHY to be used is now specified as phy-handle
- We must now check the parent of the node phy-handle points to in order to
discover if we're using internal PHY.
- The ephy clk/reset will be specified on the PHY node, not the emac node.
Care has been taken to ensure that we remain compatible with the older
bindings that we were previously using.
Tested on: Pine64 (A64, old bindings)
Tested on: Pine64-LTS (A64, new bindings) [manu]
Tested on: OrangePi-One (H3, internal PHY) [manu]
Tested on: NanoPi M1 Plus (H3, external PHY) [manu]
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D13777
The sid controller on the H3 is generally identical in location, size, and
efuse offset to the a64 and the a83t. The main difference is that the H3 has
a silicon bug that sometimes causes the rootkey (at least) to be garbled
unless first read by the prctl registers.
This device is currently not in our DTS and, as of now, is not yet present
in mainline Linux DTS.
Tested on: OrangePi One
Technically supported on the later SoCs, this will only really be used to
add support for the H3 sid. The H3 has a silicon bug that manifests itself
by returning garbled rootkeys unless first read via the prctl registers.
The emac bindings that are landing in Linux 4.15 specify a syscon property
on the emac node that point to /soc/syscon. Use this property if it's
specified, but maintain backwards compatibility with the old method.
The older method is still used for boards that we get .dtb from u-boot, such
as pine64, that did not yet have stable emac bindings.
Tested on: Banana Pi-M3 (a83t)
Tested on: Pine64 (a64)
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D13296
Newer Allwinner SoCs have nearly identical SID controllers with efuse space
starting at 0x200 into their register space and thermal data available at
0x234, making all of these fairly trivial additions.
The h3 will be added at a later time after some testing, due to a silicon
bug that causes the rootkey (at least) to be read incorrectly unless first
read via the control register.
Fully subclass the dwmmc driver and split every driver into multiple files.
There is still a few quirks in the dwmmc driver that will need some work.
Tested On: Pine64 Rock64
Differential Revision: https://reviews.freebsd.org/D13615
files that can use the default value.
It used to be required that the low-order bits of KERNVIRTADDR matched
the low-order bits of the physical load address for all arm platforms.
That hasn't been a requirement for armv6 platforms since FreeBSD 10.
There is no longer any relationship between load addr and KERNVIRTADDR
except that both must be aligned to a 2 MiB boundary.
This change makes the default KERNVIRTADDR value 0xc0000000, and removes the
options from all the platforms that can use the default value. The default
is now defined in vmparam.h, and that file is now included in a few new
places that reference KERNVIRTADDR, since it may not come in via the
forced-include of opt_global.h on the compile command line.
phy-mode can be one of: rgmii, rgmii-id, rgmii-txid, rgmii-rxid; as this was
written, any of these alternate -id configurations would break as we fail to
configure syscon for rgmii. Instead, simply check that phy-mode is
configured for rgmii and we'll let the PHY driver handle any internal delay
configuration.
The pine64 should eventually specify phy-mode = "rgmii-txid" to address
gigabit issues when rx delay is configured, motivating this change.
kernel VA mapping in the temporary page tables set up by locore-v6.S.
The number used to be hard-coded to 64MB, which is still the default if
the kernel option is not specified. However, 64MB is insufficient for
using a large mdroot filesystem. The hard-coded number can't be safely
increased because too large a number may run into memory-mapped IO space
on some SoCs that must not be mapped as ordinary memory.
platform divergence.
Only architectures which pass arguments in registers (mips)
and platforms which use really weird compilers (any?) would
need to augment the contents of <sys/_stdarg.h>
Convert x86, arm and arm64 architectures to use <sys/_stdarg.h>
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385
The real kernel page tables are set up much earlier in initarm() now than
they were when early printf support was first added, and they end up undoing
the mapping made in locore.S for early printf support. This re-adds the
mapping after switching to the new/real kernel page tables, making early
printf work again right after switching to them.
They provide relaxed-ordered atomic access semantic. Due to the
FreeBSD memory model, the operations are syntaxical wrappers around
the volatile accesses. The volatile qualifier is used to ensure that
the access not optimized out and in turn depends on the volatile
semantic as implemented by supported compilers.
The motivation for adding the operation is to help people coming from
other systems or knowing the C11/C++ standards where atomics have
special type and require use of the special access operations. It is
still the case that FreeBSD requires plain load and stores of aligned
integer types to be atomic.
Suggested by: jhb
Reviewed by: alc, jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D13534
A comment in bcm_bsc_fill_tx_fifo() even lists sc_totlen > 0 as a
precondition for calling the routine. I apparently forgot to make the
code do what my comment said.
This variable should be pure MI except possibly for reading it in MD
dump routines. Its initialization was pure MD in 4.4BSD, but FreeBSD
changed this in r36441 in 1998. There were many imperfections in
r36441. This commit fixes only a small one, to simplify fixing the
others 1 arch at a time. (r47678 added support for
special/early/multiple message buffer initialization which I want in
a more general form, but this was too fragile to use because hacking
on the msgbufp global corrupted it, and was only used for 5 hours in
-current...)
Rather than relying on 'cluster' existing in the context they're used in,
use the argument name.
Differential Revision: https://reviews.freebsd.org/D12931
This fixes some regulator issues with a83t/BananaPi-M3; the pin value was
getting clobbered as we reconfigured the pin when initializing the
regulator.
Discussed with: ian
Recent DTS (from Linux 4.14) specify a compatible "allwinner,sun50i-h5-ccu"
for H5 SoC. Since we get the DTB from u-boot this wasn't noticed.
Add the compatible so later version of u-boot will not fail for us.
a10_gpio previously accepted only {allwinner,}drive and {allwinner,}pull for
drive/bias setting, while newer DTS is using drive-strength and
bias-{disable,pull-up,pull-down} properties. Accept these properties as
well.
Additionally make bias and drive strength optional rather than required; not
setting them should just indicate that we do not need to configure these
properties.
Tested on: BananaPi-M3 (a83t)
Reviewed by: manu
Approved by: emaste (implicit)
Obtained from: NetBSD (partially)
Differential Revision: https://reviews.freebsd.org/D13284
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
For FreeBSD/arm64's cloudabi32 support, I'm going to need a TO_PTR() in
this place. Also use it for all of the other source files, so that the
difference remains as minimal as possible.
MFC after: 2 weeks
Originally a patch by Mark Millard, augmented with information from work
done on NetBSD by jmcneill@.
Submitted by: Mark Millard (markmi@dsl-only.net)
Reviewed by: emaste, manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D13240
The r-ccu on the a83t differs from the others only by what it names the
ar100 parents. Export the _CCU macros (now converted to an enu) so that
ccu_sun8i_r can differentiate between a83t r-ccu and the others, then add
the compat string for the a83t r-ccu.
Reviewed by: manu
Approved by: emaste (mentor, implicit)
Differential Revision: https://reviews.freebsd.org/D13206
plain-vanilla ETH microcode. The QOS_VLAN firmware added support in microcode
for handling IEEE 802.1q tags, but the npe(4) driver did not actually
support the relevant signalling. As a result, it was impossible to use
VLANs with npe(4). Switching to the more basic microcode (same license)
removes the on-NIC promisisng and makes vlan(4) work on both NPE interfaces.
Ref: https://lists.freebsd.org/pipermail/freebsd-arm/2012-August/003826.html
Upon successful completion, the execve() system call invokes
exec_setregs() to initialize the registers of the initial thread of the
newly executed process. What is weird is that when execve() returns, it
still goes through the normal system call return path, clobbering the
registers with the system call's return value (td->td_retval).
Though this doesn't seem to be problematic for x86 most of the times (as
the value of eax/rax doesn't matter upon startup), this can be pretty
frustrating for architectures where function argument and return
registers overlap (e.g., ARM). On these systems, exec_setregs() also
needs to initialize td_retval.
Even worse are architectures where cpu_set_syscall_retval() sets
registers to values not derived from td_retval. On these architectures,
there is no way cpu_set_syscall_retval() can set registers to the way it
wants them to be upon the start of execution.
To get rid of this madness, let sys_execve() return EJUSTRETURN. This
will cause cpu_set_syscall_retval() to leave registers intact. This
makes process execution easier to understand. It also eliminates the
difference between execution of the initial process and successive ones.
The initial call to sys_execve() is not performed through a system call
context.
Reviewed by: kib, jhibbits
Differential Revision: https://reviews.freebsd.org/D13180
A ccu driver was added for the a83t in r326114. Add compat string to
aw_ccung and register the clocks for the a83t upon attach.
Reviewed by: manu
Approved by: emaste (mentor, implicit)
Differential Revision: https://reviews.freebsd.org/D13205
This value may be set by userspace so we need to check it before using it.
If this is not done correctly on exception return the kernel may continue
in kernel mode with all registers set to a userspace controlled value. Fix
this by moving the check into set_mcontext, and also add the missing
sanitisation from the arm64 set_regs.
Discussed with: security-officer@
MFC after: 3 days
Sponsored by: DARPA, AFRL
Upstream DTS has switched to using CCU rather than /clocks nodes. Add a CCU
driver for the a83t to bring us closer to upstream, but don't yet attach it
to ccu node.
Reviewed by: manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D12843
Add a means to specify mask/value for the prediv condition instead of
shift/width/value for clocks that have a more complex mux scenario.
Specifically, ahb1 on the a83t has the prediv applied if mux is either b10
or b11.
Reviewed by: manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D12851
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
We currently support the a83t's r_intc in a somewhat hack-ish way; our .dts
describes it as nmi_intc, and uses a subset of the actual register space to
make it line up with a20/a31 nmi offsets.
This breaks with the recent 4.14 update describing r_intc using the full
register space, so update aw_nmi to use the correct register offsets with
the right compat data in a way that doesn't break our current dts with
nmi_intc or upstream with r_intc described.
Reviewed by: manu
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D13122
Stale packets should not be transmitted when the interface comes up after being down.
Count the successfully transmitted ones for statistics and drop the rest.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D12539
Use a spare dma map when attempting to map a new mbuf on the rx path.
If the mbuf allocation fails or the dma map loading for the new mbuf fails just reuse the old mbuf
and increase the drop counter.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D12538
- use awg_encap and awg_txeof names to match iflib and other network drivers.
- handle m_collapse failure similarly by freeing the mbuf rather than reenqueuing it where it will continue to fail.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13035
TX_BUF_UA_INT is set when there are no buffers to transmit and can
happen before hw.awg.tx_interval segments have been transmitted.
To reduce load, tx cleanup should be done in hw.awg.tx_interval intervals.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13034
A packet may be built from multiple segments, don't increase the count for each segment
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13032
According to the datasheet, TX_DESC_CTL is cleared when whole frame is transmitted or all
data in the current descriptor's buffer are transmitted.
When the mbuf and mapping are stored in the first segment and in a scenario where a tx
completion interrupt arrives for a frame and only the start of the next frame was transmitted,
at the time of interrupt processing the mbuf and mapping will be freed when processing the
first segment of the next frame but the other untrasmitted segments still need to use them.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13031
In a multi segment frame, if the first tx descriptor is marked with TX_DESC_CTL
but not all tx descriptors for the other segments in the frame are set up,
the TX DMA may transmit an incomplete frame.
To prevent this, set TX_DESC_CTL for the first tx descriptor only when done
with all the other segments.
Also, don't bother cleaning transmitted tx descriptors since TX_DESC_CTL
is cleared for them by the hardware and they will be reprogrammed before
TX_DESC_CTL is reenabled for them.
Submitted by: Guy Yur <guyyur@gmail.com>
Differential Revision: https://reviews.freebsd.org/D13030
The hardware will not issue a completion interrupt for a descriptor
with TX_INT_CTL set if it doesn't also have TX_LAST_DESC set.
Submitted by: Guy Yur <guyyur_gmail.com>
Differential Revision: https://reviews.freebsd.org/D13029
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
Initially, only tag files that use BSD 4-Clause "Original" license.
RelNotes: yes
Differential Revision: https://reviews.freebsd.org/D13133
Since r324184 the root node compatible for rpi2 is "brcm,bcm2836", add
it to the compatible list of bcm2835_cpufreq.
Tested On: RPI2 v1.1 RPI2 v1.2
Reported by: many on freebsd-arm@
DTS files switch from clocks under /clocks to a ccu (Clock Controller Unit)
a while ago.
Restore A13 functionality by adding a clock driver for it.
Almost every clocks are handled, the missing ones are mostly video related
clocks.
Tested On: A13 Olinuxino
The elf_trampoline.c is not connected to build for ARMv6/v7 for long time and
it uses outdated low level cpu functions.
This blocks forthcoming cleanup of ARM code.
MFC after: 3 weeks
