OF_getprop() to get encode-int encoded values from the OF tree. This is
a no-op at present, since all existing PowerPC ports are big-endian, but
it is a correctness improvement and will be required if we have a
little-endian kernel at some future point.
Where it is totally impossible for the code ever to be used on a
little-endian system (much of powerpc/powermac, for instance), I have not
necessarily made the appropriate changes.
MFC after: 1 month
On the mpc85xx SoC family, writes to any part of a word in the CCSR affect the
full word. This prevents single-byte writes from taking the desired effect.
Code copied directly from ARM.
This will enable the elimination of a workaround in the USB driver that
artifically allocates buffers twice as big as they need to be (which
actually saves memory for very small buffers on the buggy platforms).
When deciding how to allocate a dma buffer, armv4, armv6, mips, and
x86/iommu all correctly check for the tag alignment <= maxsize as enabling
simple uma/malloc based allocation. Powerpc, sparc64, x86/bounce, and
arm64/bounce were all checking for alignment < maxsize; on those platforms
when alignment was equal to the max size it would fall back to page-based
allocators even for very small buffers.
This change makes all platforms use the <= check. It should be noted that
on all platforms other than arm[v6] and mips, this check is relying on
undocumented behavior in malloc(9) that if you allocate a block of a given
size it will be aligned to the next larger power-of-2 boundary. There is
nothing in the malloc(9) man page that makes that explicit promise (but the
busdma code has been relying on this behavior all along so I guess it works).
Arm and mips code uses the allocator in kern/subr_busdma_buffalloc.c, which
does explicitly implement this promise about size and alignment. Other
platforms probably should switch to the aligned allocator.
Make it clearer what each one means in the comments that define them.
IIC_BUSBSY was used in many places to mean two different things, either
"someone else has reserved the bus so you have to wait until they're done"
or "the signal level on the bus was not in the state I expected before/after
issuing some command".
Now IIC_BUSERR is used consistantly to refer to protocol/signaling errors,
and IIC_BUSBSY refers to ownership/reservation of the bus.
linkers no longer raise an error when undefined weak symbols are
found, but relocate as if the symbol value was 0. Note that we do not
repeat the mistake of userspace dynamic linker of making the symbol
lookup prefer non-weak symbol definition over the weak one, if both
are available. In fact, kernel linker uses the first definition
found, and ignores duplicates.
Signature of the elf_lookup() and elf_obj_lookup() functions changed
to split result/error code and the symbol address returned.
Otherwise, it is impossible to return zero address as the symbol
value, to MD relocation code. This explains the mechanical changes in
elf_machdep.c sources.
The powerpc64 R_PPC_JMP_SLOT handler did not checked error from the
lookup() call, the patch leaves the code as is (untested).
Reported by: glebius
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
When the system has more than a single PCI domain, the bus numbers
are not unique, thus they cannot be used for "pci" device numbering.
Change bus numbers to -1 (i.e. to-be-determined automatically)
wherever the code did not care about domains.
Reviewed by: jhb
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3406
running thread.
It is currently implemented only on amd64 and i386; on these
architectures, it is implemented by raising an NMI on the CPU on which
the target thread is currently running. Unlike stack_save_td(), it may
fail, for example if the thread is running in user mode.
This change also modifies the kern.proc.kstack sysctl to use this function,
so that stacks of running threads are shown in the output of "procstat -kk".
This is handy for debugging threads that are stuck in a busy loop.
Reviewed by: bdrewery, jhb, kib
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3256
The only operation which is prevented by the hold is the kernel stack
swapout for the faulted thread, which should be fine to allow.
Remove useless checks for NULL curproc or curproc->p_vmspace from the
trap_pfault() wrappers on x86 and powerpc.
Reviewed by: alc (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
As part of this, clean up tlb1_init(), since bootinfo is always NULL here just
eliminate the loop altogether.
Also, fix a bug in mmu_booke_mapdev_attr() where it's possible to map a larger
immediately following a smaller page, causing the mappings to overlap. Instead,
break up the new mapping into smaller chunks. The downside to this is that it
uses more precious TLB1 entries, which, on smaller chips (e500v2) it could cause
problems with TLB1 being out of space (e500v2 only has 16 TLB1 entries).
Obtained from: Semihalf (partial)
Sponsored by: Alex Perez/Inertial Computing
FDT_DTB_STATIC is defined in opt_platform.h, and fdt_static_dtb is in
fdt_common.h, so include those files.
Sponsored by: Alex Perez/Inertial Computing
Summary:
This is (probably step 1) of enhancing the book-e pmap to support the full
36-bit physical address space on Freescale e500 and e5500 cores.
Thus far it has only been regression tested on one platform. Since I only have
one other Book-E platform (e5500), that needs work beyond this, I haven't yet
tested it on this.
Test Plan: Regression tested on my RouterBoard RB800.
Reviewed By: marcel
Differential Revision: https://reviews.freebsd.org/D3027
Summary:
The RouterBoard uses a predefined partition map which doesn't exist in the fdt.
This change allows overriding the fdt slicer with a custom slicer, and uses this
custom slicer to define the flash map on the RouterBoard RB800.
D3305 converts the mpc85xx platform into a base class, so that systems based on
the mpc85xx platform can add their own overrides. This change builds on D3305,
and creates a RouterBoard (RB800) platform to initialize the slicer override.
Reviewed By: nwhitehorn, imp
Differential Revision: https://reviews.freebsd.org/D3345
Summary:
Some systems are based around mpc85xx, but need special initialization. By
making the mpc85xx platform a base class, these systems can be platform
subclasses, and perform board-specific initialization in addition to the mpc85xx
initialization.
Test Plan:
Tested on my RB800. A platform class was created, and will be committed
separately.
Reviewed By: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D3305
* Since r257190 the kernel must actually be loaded at a 64MB boundary, not 16MB.
* Don't program HID1 register on e500mc or e5500, they don't have this SPR.
* Set proper HID0 defaults for these new architectures.
There is still more work to be done for the various SoCs, and the PMAP code
still needs to be extended to 36-bit paddr, coming soon.
Obtained from: Semihalf
Sponsored by: Alex Perez/Inertial Computing
Rather than special casing on PCIC_BRIDGE || PCIC_PROCESSOR, allow all
HDRTYPE_BRIDGE types.
Obtained from: Semihalf
Sponsored by: Alex Perez/Intertial Computing
initial thread stack is not adjusted by the tunable, the stack is
allocated too early to get access to the kernel environment. See
TD0_KSTACK_PAGES for the thread0 stack sizing on i386.
The tunable was tested on x86 only. From the visual inspection, it
seems that it might work on arm and powerpc. The arm
USPACE_SVC_STACK_TOP and powerpc USPACE macros seems to be already
incorrect for the threads with non-default kstack size. I only
changed the macros to use variable instead of constant, since I cannot
test.
On arm64, mips and sparc64, some static data structures are sized by
KSTACK_PAGES, so the tunable is disabled.
Sponsored by: The FreeBSD Foundation
MFC after: 2 week
vm_offset_t pmap_quick_enter_page(vm_page_t m)
void pmap_quick_remove_page(vm_offset_t kva)
These will create and destroy a temporary, CPU-local KVA mapping of a specified page.
Guarantees:
--Will not sleep and will not fail.
--Safe to call under a non-sleepable lock or from an ithread
Restrictions:
--Not guaranteed to be safe to call from an interrupt filter or under a spin mutex on all platforms
--Current implementation does not guarantee more than one page of mapping space across all platforms. MI code should not make nested calls to pmap_quick_enter_page.
--MI code should not perform locking while holding onto a mapping created by pmap_quick_enter_page
The idea is to use this in busdma, for bounce buffer copies as well as virtually-indexed cache maintenance on mips and arm.
NOTE: the non-i386, non-amd64 implementations of these functions still need review and testing.
Reviewed by: kib
Approved by: kib (mentor)
Differential Revision: http://reviews.freebsd.org/D3013
in lockstat.ko. This means that lockstat probes now have typed arguments and
will utilize SDT probe hot-patching support when it arrives.
Reviewed by: gnn
Differential Revision: https://reviews.freebsd.org/D2993
If KSTACK_PAGES was changed to anything alse than the default,
the value from param.h was taken instead in some places and
the value from KENRCONF in some others. This resulted in
inconsistency which caused corruption in SMP envorinment.
Ensure all places where KSTACK_PAGES are used the opt_kstack_pages.h
is included.
The file opt_kstack_pages.h could not be included in param.h
because was breaking the toolchain compilation.
Reviewed by: kib
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3094
It appears that the linker will not handle 64-bit relocations at addresses that
are not aligned to 8-byte boundaries. Prior to this change the line:
.llong generictrap
was aligned to a 4-byte address, and the linker replaced that with an 8-byte
0x0. Aligning that address to 8 bytes caused the linker to generate the proper
relocation. As a follow-through, the dblow from trap_subr33.S used the code
sequence 'lwz %r1, TRAP_GENTRAP(0)', so this reproduces the analogue of that for
64-bit.
provide a semantic defined by the C11 fences with corresponding
memory_order.
atomic_thread_fence_acq() gives r | r, w, where r and w are read and
write accesses, and | denotes the fence itself.
atomic_thread_fence_rel() is r, w | w.
atomic_thread_fence_acq_rel() is the combination of the acquire and
release in single operation. Note that reads after the acq+rel fence
could be made visible before writes preceeding the fence.
atomic_thread_fence_seq_cst() orders all accesses before/after the
fence, and the fence itself is globally ordered against other
sequentially consistent atomic operations.
Reviewed by: alc
Discussed with: bde
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
Summary:
Both booke and AIM interrupt.c files contain nearly identical code. This merges
the two files, to reduce duplication.
Reviewers: #powerpc, marcel
Reviewed By: marcel
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2991
On Book-E, physical addresses are actually 36-bits, not 32-bits. This is
currently worked around by ignoring the top bits. However, in some cases, the
boot loader configures CCSR to something above the 32-bit mark. This is stage 1
in updating the pmap to handle 36-bit physaddr.
This will print out the Memory Subsystem Status Register on MPC745x (G4+ class),
and the Machine Check Status Register on Book-E class CPUs, to aid in debugging
machine checks. Other relevant registers, for other CPUs, can be added in the
future.
This will require for AArch64 as we dont have modules yet.
Sponsored by: HEIF5
Sponsored by: ARM Ltd.
Differential Revision: https://reviews.freebsd.org/D1997
Thread credentials are maintained as follows: each thread has a pointer to
creds and a reference on them. The pointer is compared with proc's creds on
userspace<->kernel boundary and updated if needed.
This patch introduces a counter which can be compared instead, so that more
structures can use this scheme without adding more comparisons on the boundary.
Native ABI do not need signal conversion, only emulators may want this. Usually
emulators implements its own sv_sendsig method. For now only ibcs2 emulator does
not have own sv_sendsig implementation and depends on native sendsig() method.
So, remove any extra attempts to convert signal numbers from native sendsig()
methods except from i386 where ibsc2 is living.
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
The replacement started at r283088 was necessarily incomplete without
replacing boolean_t with bool. This also involved cleaning some type
mismatches and ansifying old C function declarations.
Pointed out by: bde
Discussed with: bde, ian, jhb
needs to be enabled by adding "kern.racct.enable=1" to /boot/loader.conf.
Differential Revision: https://reviews.freebsd.org/D2407
Reviewed by: emaste@, wblock@
MFC after: 1 month
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Summary:
The Freescale PCIe Root Complex shows up as a Processor class device, PowerPC
subclass, so the generic PCI code ignores it for a bridge. This adds support
for it.
As part of this, update the Freescale PCI hostbridge driver, to allow probing
beyond the root complex, instead of only allowing "proper" PCI-PCI bridges.
Reviewers: #powerpc, marcel, nwhitehorn
Reviewed By: nwhitehorn
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2442
Relnotes: yes
Much of the code was common to begin with. There is one nit, which is likely
not an issue at all. With the old code, the AIM machdep would __syncicache()
the entire kernel core at setup. However, in the unified setup, that seems to
hang on the MPC7455, perhaps because it's running later than before. Removing
this allows it to boot just fine. Examining the code, the FreeBSD loader
already does syncicache of the full kernel, and each module loaded, so this
doesn't appear to be an actual problem.
Initial code by Nathan Whitehorn.
pages which pass a NULL virtual address. If the BUS_DMA_KEEP_PG_OFFSET
flag is set, use the physical address to compute the page offset
instead. The physical address should always be valid when adding
bounce pages and should contain the same page offset like the virtual
address.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
MFC after: 1 week
Reviewed by: jhb@
This supports e500v1, e500v2, and e500mc. Tested only on e500v2, but the
performance counters are identical across all, with e500mc having some
additional events.
Relnotes: Yes
and export them to userland.
- Define __HAVE_REG32 on platforms that define a reg32 structure and check
for this in <sys/procfs.h> to control when to export prstatus32, etc.
- Add prstatus32_t and prpsinfo32_t typedefs for the 32-bit structures.
libbfd looks for these types, and having them fixes 'gcore' in gdb of a
32-bit process on a 64-bit platform.
- Use the structure definitions from <sys/procfs.h> in gcore's elf32 core
dump code instead of duplicating the definitions.
Differential Revision: https://reviews.freebsd.org/D2142
Reviewed by: kib, nathanw (powerpc bits)
MFC after: 1 week
Summary:
Book-E and AIM trap.c are almost identical, except for a few bits. This is step
1 in unifying them.
This also renumbers EXC_DEBUG, to not conflict with AIM vector numbers. Since
this is the only one thus far that is used in the switch statement in trap(),
it's the only one renumbered. If others get added to the switch, which conflict
with AIM numbers, they should also be renumbered.
Reviewers: #powerpc, marcel, nwhitehorn
Reviewed By: marcel
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2215
A couple of internal functions used by malloc(9) and uma truncated
a size_t down to an int. This could cause any number of issues
(e.g. indefinite sleeps, memory corruption) if any kernel
subsystem tried to allocate 2GB or more through malloc. zfs would
attempt such an allocation when run on a system with 2TB or more
of RAM.
Note to self: When this is MFCed, sparc64 needs the same fix.
Differential revision: https://reviews.freebsd.org/D2106
Reviewed by: kib
Reported by: Michael Fuckner <michael@fuckner.net>
Tested by: Michael Fuckner <michael@fuckner.net>
MFC after: 2 weeks
writing approximately never (< 0.00000001% under heavy VM load, and it can
go for months without ever being acquired in normal operation). This
provides a 10% (2-minute) improvement in wall clock time for make -j32
buildworld on a 4-core 32-thread POWER8.
packets and does not schedule interrupts for any packets currently
enqueued. Close two races where enqueued packets may not ever trigger
interrupts. The first of these, at adapter initialization time, was
especially severe since a rush of enqueued packets could actually fill
the receive buffer completely, stalling the interface forever.
MFC after: 2 weeks
This is not complete yet: the gem(4) interface on my laptop seems to
disappear from the PCI bus as a result of quiescing Open Firmware in the
boot loader.
The vtophys() function is used to get the physical page address for
the virtually allocated frame buffers when a physically continuous
memory area is not available. This change also allows removing the
masking of the FB_FLAG_NOMMAP flag in the PS3 syscons driver.
The FB and VT drivers were tested using X.org/xf86-video-scfb and
syscons.
executables. The goal here, not yet accomplished, is to let the e500 kernel
run under QEMU by setting KERNBASE to something that fits in low memory and
then having the kernel relocate itself at runtime.
have the same meaning and occupy the same memory address in the trapframe
courtesy of union. Avoid some pointless #ifdef by spelling them both 'DAR'
in the trapframe.
Fix an extremely subtle concurrency bug triggered by running on 32-thread
POWER8 systems. During thread switch, there was a very small window when
the stack pointer was set to the stack pointer of the outgoing thread, but
after the lock on that thread had already been released.
If, during that window, the outgoing thread were rescheduled on another CPU
and begin execution and an exception were taken on the original CPU, the
trap handler and the outgoing thread would simultaneously execute on the same
stack, causing memory corruption. Fix this by making sure to release the
old thread only after cpu_switch() is done with its stack.
MFC after: 2 weeks
this change is to improve concurrency:
- Drop global state stored in the shadow overflow page table (and all other
global state)
- Remove all global locks
- Use per-PTE lock bits to allow parallel page insertion
- Reconstruct state when requested for evicted PTEs instead of buffering
it during overflow
This drops total wall time for make buildworld on a 32-thread POWER8 system
by a factor of two and system time by a factor of three, providing performance
20% better than similarly clocked Core i7 Xeons per-core. Performance on
smaller SMP systems, where PMAP lock contention was not as much of an issue,
is nearly unchanged.
Tested on: POWER8, POWER5+, G5 UP, G5 SMP (64-bit and 32-bit kernels)
Merged from: user/nwhitehorn/ppc64-pmap-rework
Looked over by: jhibbits, andreast
MFC after: 3 months
Relnotes: yes
Sponsored by: FreeBSD Foundation
and POWER8. This instruction set unifies the 32 64-bit scalar floating
point registers with the 32 128-bit vector registers into a single bank
of 64 128-bit registers. Kernel support mostly amounts to saving and
restoring the wider version of the floating point registers and making
sure that both scalar FP and vector registers are enabled once a VSX
instruction is executed. get_mcontext() and friends currently cannot
see the high bits, which will require a little more work.
As the system compiler (GCC 4.2) does not support VSX, making use of this
from userland requires either newer GCC or clang.
Relnotes: yes
Sponsored by: FreeBSD Foundation
Summary:
Currently, fan control is linear between the target temperature and max
temperature, which is far from ideal. This changes it to be proportional to the
distance between the current temperature and the two endpoints (target and max
temp). This also adds a hysteresis, so that fans keep going when the
temperature drops, for about 10 seconds, before slowing down.
Reviewers: nwhitehorn
Reviewed By: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D1549
MFC after: 3 weeks
Some ATI-based PowerBooks use the string 'mnca' in the backlight controller
device tree entry, so account for this and don't use nVidia when it's not an
nVidia device.
MFC after: 3 weeks
This port failed to gain traction and probably only a couple Wii consoles
ran FreeBSD all the way to single user mode with an md(4). IPC
support was never implemented, so it was impossible to use any peripheral
Any further development, if any, will happen at https://github.com/rpaulo/wii.
Discussed with: nathanw (a long time ago), jhibbits
hypervisor. This prevents an infinite loop where processes with evicted
pages would page fault forever when PMAP decided the evicted pages on
which the process was faulting was actually present and did not need to
be restored.
Found while building LLVM with make -j32.
Sponsored by: FreeBSD Foundation
POWER8 systems. During thread switch, there was a very small window when
the stack pointer was set to the stack pointer of the outgoing thread, but
after the lock on that thread had already been released.
If, during that window, the outgoing thread were rescheduled on another CPU
and begin execution and an exception were taken on the original CPU, the
trap handler and the outgoing thread would simultaneously execute on the same
stack, causing memory corruption. Fix this by making sure to release the
old thread only after cpu_switch() is done with its stack.
MFC after: 2 weeks
Sponsored by: FreeBSD Foundation
every possible trap address by default. This also makes sure the kernel
notices (and panics at) traps from newer CPUs that the kernel was not
expecting rather than executing gibberish memory.
that we (a) get the correct large page size to provide to pmap and (b)
we can alert the user if running under incorrectly-configured PowerKVM
on POWER7 and POWER8 systems.
MFC after: 1 week
const. On x86, even after the machine context is supposedly read into
the struct ucontext, lazy FPU state save code might only mark the FPU
data as hardware-owned. Later, set_fpcontext() needs to fetch the
state from hardware, modifying the *mcp.
The set_mcontext(9) is called from sigreturn(2) and setcontext(2)
implementations and old create_thread(2) interface, which throw the
*mcp out after the set_mcontext() call.
Reported by: dim
Discussed with: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
support in QEMU. Each page of a many page mapping was getting mapped to
the same physical address, which is not the desired behavior.
MFC after: 1 week
A "size" symbol with its address set to the length of handler would be
shifted forward with all other addresses when relocations are processed.
Instead, just note the end and do the subtraction at runtime.
mostly a no-op since all currently-supported instances of these CPUs give
the number of SLB slots in the device tree, but keep it here as well just
in case.
instructions to call through pointers instead. In general, these are set
implicitly through relocation processing. One has to be set explicitly in
machdep.c, however, to fit one handler in the tiny (8 instruction) space
available.
Reviewed by: andreast
Differential revision: D1554
Tested on: UP and SMP G5, Cell, POWER5+
sequences, like are used to read the HIDs. This is both easier to read
and avoids a miscompilation by GCC in certain circumstances. Also avoid
double restoration of HID4 and HID5.
MFC after: 2 weeks
in ofw_mem_regions(). This function is actually MI and should move to
dev/ofw at some point in the near future so that ARM and MIPS can use the
same code.
PVO pool size. The default errs on the exceedingly large side, so absent
any intelligent automatic tuning, at least let the user set it to save
RAM on memory-constrained systems.
MFC after: 2 weeks
This allows executing static clang built with -O0.
The value is configurable by a sysctl, so if one needs to clamp it down, they
still can.
Discussed with: nwhitehorn,emaste
code in sys/kern/kern_dump.c. Most dumpsys() implementations are nearly
identical and simply redefine a number of constants and helper subroutines;
a generic implementation will make it easier to implement features around
kernel core dumps. This change does not alter any minidump code and should
have no functional impact.
PR: 193873
Differential Revision: https://reviews.freebsd.org/D904
Submitted by: Conrad Meyer <conrad.meyer@isilon.com>
Reviewed by: jhibbits (earlier version)
Sponsored by: EMC / Isilon Storage Division
the Open Firmware, as provided by petitboot, for example. Note that this is
not quite complete, since RTAS instantiation still depends on callable
firmware.
MFC after: 2 weeks
It's redundant at the moment since it can be obtained from the trapframe
on the architectures where DTrace is supported, but this won't be the case
with ARM.
WITNESS and INVARIANTS checking, which are known to have significant
performance impact on running systems. When benchmarking new features
this kernel should be used instead of the standard GENERIC.
This kernel configuration should never appear outside of the HEAD
of the FreeBSD tree.
Summary:
Revert the initial FBT-with-KDB changes for trap_subr*.S, and instead use the
db_trap filter function to handle dtrace trap filtering. With this, the MMU is
enabled by the support code, simplifying the codepath altogether.
Test Plan: Tested on my G4 PowerBook
Reviewers: #powerpc, nwhitehorn
Reviewed By: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D1207
MFC after: 3 weeks
It is automatically set when -fPIC is passed to the compiler.
Reviewed by: dim, kib
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D1179
Summary:
Currently if there are problems finding a symbol, backtrace ends up printing
something like:
0xdeadbeef: at +0x12345
Which is pretty useless. This on its own should be fixed (retrieving symbols),
but aside from that, using db_printsym() is a better solution anyway. If it
can't find a valid symbol it prints the actual address, and it has the added
benefit that if it can find the symbol, it might be able to print the file and
line as well.
Test Plan: Tested on my G4 PowerBook
Reviewers: #powerpc, nwhitehorn
Reviewed By: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D1173
MFC after: 3 weeks
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
of fuword(9) and suword(9). This makes the functions type-compatible
with volatile objects and does not require devolatile force, e.g. in
kern_umtx.c.
Requested by: bde
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
unit 0.
It seems that this 'simplification' was copied to all GPIO drivers in tree.
This fix a bug where a GPIO controller could fail to attach its children
(gpioc and gpiobus) if another GPIO driver attach first.
and casuword(9), but do not mix value read and indication of fault.
I know (or remember) enough assembly to handle x86 and powerpc. For
arm, mips and sparc64, implement fueword() and casueword() as wrappers
around fuword() and casuword(), which means that the functions cannot
distinguish between -1 and fault.
On architectures where fueword() and casueword() are native, implement
fuword() and casuword() using fueword() and casuword(), to reduce
assembly code duplication.
Sponsored by: The FreeBSD Foundation
Tested by: pho
MFC after: 2 weeks (ia64 needs treating)
- Wrong integer type was specified.
- Wrong or missing "access" specifier. The "access" specifier
sometimes included the SYSCTL type, which it should not, except for
procedural SYSCTL nodes.
- Logical OR where binary OR was expected.
- Properly assert the "access" argument passed to all SYSCTL macros,
using the CTASSERT macro. This applies to both static- and dynamically
created SYSCTLs.
- Properly assert the the data type for both static and dynamic
SYSCTLs. In the case of static SYSCTLs we only assert that the data
pointed to by the SYSCTL data pointer has the correct size, hence
there is no easy way to assert types in the C language outside a
C-function.
- Rewrote some code which doesn't pass a constant "access" specifier
when creating dynamic SYSCTL nodes, which is now a requirement.
- Updated "EXAMPLES" section in SYSCTL manual page.
MFC after: 3 days
Sponsored by: Mellanox Technologies
in userland rename in-kernel getenv()/setenv() to kern_setenv()/kern_getenv().
This fixes a namespace collision with libc symbols.
Submitted by: kmacy
Tested by: make universe
For compatibility, 'device windtunnel' is still supported, but one should use
'device adm1030' instead, and this has been updated in GENERIC and NOTES.
Summary:
If a user uses powerd, or doesn't want to use the cycles monitoring, they can
now suspend the monitoring thread.
While here, reorganize the added prototypes to match existing groupings.
Reviewers: nwhitehorn, #powerpc, rpaulo
Reviewed By: #powerpc, rpaulo
Differential Revision: https://reviews.freebsd.org/D944
X-MFC-with: r273009
MFC after: 3 weeks
Summary:
Add a polling loop (1Hz) to monitor the battery and AC status, to notify devd
like ACPI does for power monitoring. This allows /etc/rc.d/power_profile to
work on PowerPC laptops
Test Plan:
Tested on a Titanium PowerBook, configuring economy_cpu_freq and
performance_cpu_freq, disabling powerd.
Reviewers: #powerpc, nwhitehorn
Reviewed By: nwhitehorn
Subscribers: rpaulo
Differential Revision: https://reviews.freebsd.org/D937
node's interrupts=<...> property creating resource list entries with a
single common implementation. This change makes ofw_bus_intr_to_rl() the
one true copy of that code and removes the copies of it from other places.
This also adds handling of the interrupts-extended property, which allows
specifying multiple interrupts for a node where each interrupt can have a
separate interrupt-parent. The bindings for this state that the property
cells contain an xref phandle to the interrupt parent followed by whatever
interrupt info that parent normally expects. This leads to having a
variable number of icells per interrupt in the property. For example you
could have <&intc1 1 &intc2 26 9 0 &intc3 9 4>.
Differential Revision: https://reviews.freebsd.org/D803
When the FreeBSD kernel is loaded from Xen the symtab and strtab are
not loaded the same way as the native boot loader. This patch adds
three new global variables to ddb that can be used to specify the
exact position and size of those tables, so they can be directly used
as parameters to db_add_symbol_table. A new helper is introduced, so callers
that used to set ksym_start and ksym_end can use this helper to set the new
variables.
It also adds support for loading them from the Xen PVH port, that was
previously missing those tables.
Sponsored by: Citrix Systems R&D
Reviewed by: kib
ddb/db_main.c:
- Add three new global variables: ksymtab, kstrtab, ksymtab_size that
can be used to specify the position and size of the symtab and
strtab.
- Use those new variables in db_init in order to call db_add_symbol_table.
- Move the logic in db_init to db_fetch_symtab in order to set ksymtab,
kstrtab, ksymtab_size from ksym_start and ksym_end.
ddb/ddb.h:
- Add prototype for db_fetch_ksymtab.
- Declate the extern variables ksymtab, kstrtab and ksymtab_size.
x86/xen/pv.c:
- Add support for finding the symtab and strtab when booted as a Xen
PVH guest. Since Xen loads the symtab and strtab as NetBSD expects
to find them we have to adapt and use the same method.
amd64/amd64/machdep.c:
arm/arm/machdep.c:
i386/i386/machdep.c:
mips/mips/machdep.c:
pc98/pc98/machdep.c:
powerpc/aim/machdep.c:
powerpc/booke/machdep.c:
sparc64/sparc64/machdep.c:
- Use the newly introduced db_fetch_ksymtab in order to set ksymtab,
kstrtab and ksymtab_size.
than u_char.
Migrate post_filter to use an int for a CPU rather than u_char.
Change intr_event_bind() to use an int for CPU rather than u_char.
It touches the ppc, sparc64, arm and mips machdep code but it should
(hah!) be a no-op.
Tested:
* i386, AMD64 laptops
Reviewed by: jhb
physical address of the page to direct map address, in case
SFBUF_OPTIONAL_DIRECT_MAP returns true. The case of PowerPC AIM
64bit, where the page physical address is identical to the direct map
address, is accidental.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
mapping size (currently unused). The flags includes the fault access
bits, wired flag as PMAP_ENTER_WIRED, and a new flag
PMAP_ENTER_NOSLEEP to indicate that pmap should not sleep.
For powerpc aim both 32 and 64 bit, fix implementation to ensure that
the requested mapping is created when PMAP_ENTER_NOSLEEP is not
specified, in particular, wait for the available memory required to
proceed.
In collaboration with: alc
Tested by: nwhitehorn (ppc aim32 and booke)
Sponsored by: The FreeBSD Foundation and EMC / Isilon Storage Division
MFC after: 2 weeks
The MD allocators were very common, however there were some minor
differencies. These differencies were all consolidated in the MI allocator,
under ifdefs. The defines from machine/vmparam.h turn on features required
for a particular machine. For details look in the comment in sys/sf_buf.h.
As result no MD code left in sys/*/*/vm_machdep.c. Some arches still have
machine/sf_buf.h, which is usually quite small.
Tested by: glebius (i386), tuexen (arm32), kevlo (arm32)
Reviewed by: kib
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
We continue to use pmap_enter() for that. For unwiring virtual pages, we
now use pmap_unwire(), which unwires a range of virtual addresses instead
of a single virtual page.
Sponsored by: EMC / Isilon Storage Division
by the combination of r268591 and r269134: When we attempt to add the
wired attribute to an existing mapping, moea{,64}_pvo_enter() do nothing.
(They only set the wired attribute on newly created mappings.)
Tested by: andreast
pmap_unwire(), the call to MOEA64_PVO_TO_PTE() must be performed before
any changes are made to the PVO. Otherwise, MOEA64_PVO_TO_PTE() will
panic.
Reported by: andreast
rebased to point to the allocated memory, but for architectures
that have non-zero relocation addends, the address comparison
happens on the "unfinalized" address.
After the addend is taken into account, call elf_relocaddr() to
make sure we rebase properly.
This commit does not add error returns to minidumpsys() or
textdump_dumpsys(); those can also be added later.
Submitted by: Conrad Meyer (EMC / Isilon storage division)
calling mmap on /dev/mem and add a handler for the possible userland
machine checks that may result. Remove some pointless and wrong copy/paste
that has been in here for a decade as well.
This results in a /dev/mem with identical semantics to the x86 version.
MFC after: 1 week
the upstream implementation and helps ensure that a trap induced by tracing
fbt::trap:entry is handled without recursively generating another trap.
This makes it possible to run most (but not all) of the DTrace tests under
common/safety/ without triggering a kernel panic.
Submitted by: Anton Rang <anton.rang@isilon.com> (original version)
Phabric: D95
