. interrupt storm detected on "intr70:"; throttling interrupt source;
. Added access serialization on iicbus_transfer(), previously there was
no such protection and a new transfer could easily confuse the
controller;
. Add error checkings (i.e. stop the transfer when a error is detected
and do _not_ overwrite the previous error);
. On command done interrupt do not assume that the transfer was finished
sucessfully as we will receive the command done interrupt even after
errors;
. Simplify the FIFO handling;
. Reset the FIFO between the transfers as the FIFO may contain data from
the last (failed) transfer;
. Fix the iicbus speed for AM335x, which in turn will make better use of
the I2C noise filter (set to one internal clock cycle);
. Move the read and write handler to ithread instead of notifying the
requesting thread with wakeup(9);
. Fix the comments based on OMAP4 TRM.
The above changes allows me to read the EDID from my HDMI monitor on BBB
with gonzo's patches to support TDA19988 (which does 128 bytes reads) and
repeatedly scan the iicbus (with a modified i2c(8)) without lock up the bus.
Phabric: D465
(7-bit device address << 1), always leaving the room for the read/write bit.
This commit convert ti_i2c and revert r259127 on bcm2835_bsc to make them
compatible with 8-bit addresses. Previous to this commit an i2c device
would have different addresses depending on the controller it was attached
to (by example, when compared to any iicbb(4) based i2c controller), which
was a pretty annoying behavior.
Also, update the PMIC i2c address on beaglebone* DTS files to match the new
address scheme.
Now the userland utilities need to do the correct slave address shifting
(but it is going to work with any i2c controller on the system).
Discussed with: ian
MFC after: 2 weeks
The ti_i2c controller only works in the master mode and the i2c address
passed on iicbus_reset() is used to set the controller slave address when
operating as an i2c slave (which isn't currently supported).
When talking to a slave, the slave address is correctly provided to
ti_i2c_tranfer().
through a voltage divisor (R163 and R164 on page 4 of BBB schematic).
Add a note about this on ti_adc(4) man page. The ti_adc(4) man page will
first appear on 10.1-RELEASE.
MFC after: 1 week
Suggested by: Sulev-Madis Silber (ketas)
Manual page reviewed by: brueffer (D127)
and the actual PWM frequency.
Enforce the maximum value for the period sysctl.
The frequency systcl now allows the direct setting of the PWM frequency (it
will try to find the better clkdiv and period for a given frequency, i.e.
the ones that will give the better PWM resolution).
This allows the use lower frequencies on the PWM. Without changing the
clock prescaler the minimum PWM frequency was 1.52kHz.
PWM frequencies checked with an osciloscope.
PWM output tested with some R/C servos at 50Hz.
memory ordering model allows writes to different devices to complete out
of order, leading to a situation where the write that clears an interrupt
source at a device can complete after a write that unmasks and EOIs the
interrupt at the interrupt controller, leading to a spurious re-interrupt.
This adds a generic barrier function specific to the needs of interrupt
controllers, and calls that function from the GIC and TI AINTC controllers.
There may still be other soc-specific controllers that need to make the call.
Reviewed by: cognet, Svatopluk Kraus <onwahe@gmail.com>
MFC after: 3 days
platform code, it is expected these will be merged in the future when the
ARM code is more complete.
Until more boards can be tested only use this with the Raspberry Pi and
rrename the functions on the other SoCs.
Reviewed by: ian@
While it is the recommended initialization procedure, it hangs on the reset
of the second GPIO module on pandaboard.
Removes the module reset for now as more investigation would be needed.
Reported by: jceel
On AM335x each one of the four GPIO banks has two physical interrupt
lines, so we now allocate resources and setup our interrupt handler for
all the (8) available interrupts.
On OMAP3 and OMAP4 there is only one interrupt for each GPIO bank (6
banks, 6 interrupts), but there are two set of registers where the
first one is used to setup the delivery of interrupts to the MPU and
the second set, setup the delivery of interrupts to the DSP.
On AM335x, each set of registers controls each one of the interrupt
lines.
- Remove nonexistent registers for OMAP4 and AM335x, replace their use with
the correct ones for these SoCs.
- Remove stray whitespace.
Based on OMAP3, OMAP4 and AM335x TRMs.
Tested on Beaglebone-black.
- Don't allow high-speed mode on OMAP4 due to hardware erratum.
- Check the proper bit in the status register when waiting for the
controller to come out of reset.
- Add handling for the "non-removable" fdt property by always returning
"card is present" status.
- Add the non-removable property for the MMC card on a Beaglebone Black.
- Add the non-removable property for Pandaboard as a workaround.
For Pandaboard the card detect pin is handled by the twl6030 fpga device
which gets an interrupt on pin change and then has to query the fpga
for the actual status. We don't have code to do that yet.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
errors.
Reset the GPIO module during the initialization. This is guaranteed to be
the same as a hardware reset. Tested on AM335x (BBB) and checked against
the omap3 and omap4 TRM.
Do a better job freeing resources when there are errors and on
ti_gpio_detach().
description was eaten by the dog (or an editor crash or something).
Add variable-frequency support to the arm mpcore eventtimer driver.
This allows a platform's early init code to tell the mpcore driver that the
clock frequency can vary. That causes the mpcore driver to register an
eventtimer, but not a timecounter. The platform has to provide a time
counter using some other fixed-frequency clock, but can still use the
per-cpu goodness of the mpcore hardware for event timers.
When the platform support code does something to change the frequency of
the CPU clocks (power saving, thermal management) it must tell the mpcore
driver code about it using arm_tmr_change_frequency().
The ADC has a 12bit resolution and its raw output can be read via sysctl(8)
interface.
The driver allows the setup of ADC clock, samples average and open delay
(the number of clock cycles to wait before start the conversion).
The TSC_ADC module is set in the general purpose mode (no touchscreen
support).
Tested on Beaglebone-black.
Written based on AM335x TRM.
Reviewed by: rpaulo
Approved by: adrian (mentor)
Tested by: me, Brian J. McGovern, Sulev-Madis Silber (ketas)
and the functionality it provided into arm/exception.S. Rename the main
irq handling routine from arm_handler_execute() to arm_irq_handler() to
make it more congruent with how other exception handlers are named, and
also update its signature to reflect what has long been reality: it is
passed just a trapframe pointer, no interrupt number argument.
appropriate for each of the 'foo' in the tree. This will allow us to
compile them together (although symbol conflicts prevent us from doing
that today, this just fixes the file name collision).
implementation in arm/machdep.c. Most arm platforms either don't need to
do anything, or just need to call the standard eventtimer init routines.
A generic implementation that does that is now provided via weak linkage.
Any platform that needs to do something different can provide a its own
implementation to override the generic one.
it into a bunch of different .c files. Remove declarations for the unused
mptramp() function from everywhere except AramadaXP (and I think it's
really not used there either, because the code that references it appears
to be insanely does-nothing in nature).
change the gpio children can be described as directly connected to the GPIO
controller without the need of describing the OFW GPIO bus itself on the
DTS file.
With this commit the OFW GPIO bus is fully functional on BBB and RPi.
GPIO controllers which want to use the OFW GPIO bus will need similar
changes.
Approved by: adrian (mentor, implicit)
to check the status property in their probe routines.
Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.
Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.
Note that this commit hasn't been compile tested because these files
are not hooked up to the build...
PR: 186129
Submitted by: Takanori Sawada
Approved by: rpaulo
and add static mappings that cover most of the on-chip peripherals with
1MB section mappings. This adds about 220MB or so available kva space
by not using a hard-coded 0xF0000000 as the mapping address.
searching. If you didn't configure a timer capture pin you'd get a data
abort as it wandered into the weeds, now you get a nice warning message
about your config, as originally intended.
capture mode together with the timecounter's PPS polling feature to get
very accurate PPS capture without any interrupt processing (or latency).
Hardware timers 4 through 7 have associated capture-trigger input pins.
When the PPS support is compiled in the code automatically chooses the
first timer it finds that has the capture-trigger pin set to input mode
(this is configured via the fdt data).
- Use named constants for register bits, instead of mystery numebrs
scattered around in the code.
- Use inline functions for bus space read/write, instead of macros
that rely on global variables.
- Move the timecounter struct into the softc instead of treating it
as a global variable. Backlink from it to the softc.
- This leaves a pointer to the softc as the only static/global variable
and it's now used only by DELAY().
this change we may end up with a panic (Fatal kernel mode data abort:
'External Non-Linefetch Abort (S)') as described in
http://e2e.ti.com/support/arm/sitara_arm/f/791/t/276862.aspx.
It is now possible to bring up I2C1 and I2C2 on BBB.
Approved by: adrian (mentor)
