If KSTACK_PAGES was changed to anything alse than the default,
the value from param.h was taken instead in some places and
the value from KENRCONF in some others. This resulted in
inconsistency which caused corruption in SMP envorinment.
Ensure all places where KSTACK_PAGES are used the opt_kstack_pages.h
is included.
The file opt_kstack_pages.h could not be included in param.h
because was breaking the toolchain compilation.
Reviewed by: kib
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3094
It appears that the linker will not handle 64-bit relocations at addresses that
are not aligned to 8-byte boundaries. Prior to this change the line:
.llong generictrap
was aligned to a 4-byte address, and the linker replaced that with an 8-byte
0x0. Aligning that address to 8 bytes caused the linker to generate the proper
relocation. As a follow-through, the dblow from trap_subr33.S used the code
sequence 'lwz %r1, TRAP_GENTRAP(0)', so this reproduces the analogue of that for
64-bit.
provide a semantic defined by the C11 fences with corresponding
memory_order.
atomic_thread_fence_acq() gives r | r, w, where r and w are read and
write accesses, and | denotes the fence itself.
atomic_thread_fence_rel() is r, w | w.
atomic_thread_fence_acq_rel() is the combination of the acquire and
release in single operation. Note that reads after the acq+rel fence
could be made visible before writes preceeding the fence.
atomic_thread_fence_seq_cst() orders all accesses before/after the
fence, and the fence itself is globally ordered against other
sequentially consistent atomic operations.
Reviewed by: alc
Discussed with: bde
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
Summary:
Both booke and AIM interrupt.c files contain nearly identical code. This merges
the two files, to reduce duplication.
Reviewers: #powerpc, marcel
Reviewed By: marcel
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2991
On Book-E, physical addresses are actually 36-bits, not 32-bits. This is
currently worked around by ignoring the top bits. However, in some cases, the
boot loader configures CCSR to something above the 32-bit mark. This is stage 1
in updating the pmap to handle 36-bit physaddr.
This will print out the Memory Subsystem Status Register on MPC745x (G4+ class),
and the Machine Check Status Register on Book-E class CPUs, to aid in debugging
machine checks. Other relevant registers, for other CPUs, can be added in the
future.
This will require for AArch64 as we dont have modules yet.
Sponsored by: HEIF5
Sponsored by: ARM Ltd.
Differential Revision: https://reviews.freebsd.org/D1997
Thread credentials are maintained as follows: each thread has a pointer to
creds and a reference on them. The pointer is compared with proc's creds on
userspace<->kernel boundary and updated if needed.
This patch introduces a counter which can be compared instead, so that more
structures can use this scheme without adding more comparisons on the boundary.
Native ABI do not need signal conversion, only emulators may want this. Usually
emulators implements its own sv_sendsig method. For now only ibcs2 emulator does
not have own sv_sendsig implementation and depends on native sendsig() method.
So, remove any extra attempts to convert signal numbers from native sendsig()
methods except from i386 where ibsc2 is living.
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
The replacement started at r283088 was necessarily incomplete without
replacing boolean_t with bool. This also involved cleaning some type
mismatches and ansifying old C function declarations.
Pointed out by: bde
Discussed with: bde, ian, jhb
needs to be enabled by adding "kern.racct.enable=1" to /boot/loader.conf.
Differential Revision: https://reviews.freebsd.org/D2407
Reviewed by: emaste@, wblock@
MFC after: 1 month
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Summary:
The Freescale PCIe Root Complex shows up as a Processor class device, PowerPC
subclass, so the generic PCI code ignores it for a bridge. This adds support
for it.
As part of this, update the Freescale PCI hostbridge driver, to allow probing
beyond the root complex, instead of only allowing "proper" PCI-PCI bridges.
Reviewers: #powerpc, marcel, nwhitehorn
Reviewed By: nwhitehorn
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2442
Relnotes: yes
Much of the code was common to begin with. There is one nit, which is likely
not an issue at all. With the old code, the AIM machdep would __syncicache()
the entire kernel core at setup. However, in the unified setup, that seems to
hang on the MPC7455, perhaps because it's running later than before. Removing
this allows it to boot just fine. Examining the code, the FreeBSD loader
already does syncicache of the full kernel, and each module loaded, so this
doesn't appear to be an actual problem.
Initial code by Nathan Whitehorn.
pages which pass a NULL virtual address. If the BUS_DMA_KEEP_PG_OFFSET
flag is set, use the physical address to compute the page offset
instead. The physical address should always be valid when adding
bounce pages and should contain the same page offset like the virtual
address.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
MFC after: 1 week
Reviewed by: jhb@
This supports e500v1, e500v2, and e500mc. Tested only on e500v2, but the
performance counters are identical across all, with e500mc having some
additional events.
Relnotes: Yes
and export them to userland.
- Define __HAVE_REG32 on platforms that define a reg32 structure and check
for this in <sys/procfs.h> to control when to export prstatus32, etc.
- Add prstatus32_t and prpsinfo32_t typedefs for the 32-bit structures.
libbfd looks for these types, and having them fixes 'gcore' in gdb of a
32-bit process on a 64-bit platform.
- Use the structure definitions from <sys/procfs.h> in gcore's elf32 core
dump code instead of duplicating the definitions.
Differential Revision: https://reviews.freebsd.org/D2142
Reviewed by: kib, nathanw (powerpc bits)
MFC after: 1 week
Summary:
Book-E and AIM trap.c are almost identical, except for a few bits. This is step
1 in unifying them.
This also renumbers EXC_DEBUG, to not conflict with AIM vector numbers. Since
this is the only one thus far that is used in the switch statement in trap(),
it's the only one renumbered. If others get added to the switch, which conflict
with AIM numbers, they should also be renumbered.
Reviewers: #powerpc, marcel, nwhitehorn
Reviewed By: marcel
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2215
A couple of internal functions used by malloc(9) and uma truncated
a size_t down to an int. This could cause any number of issues
(e.g. indefinite sleeps, memory corruption) if any kernel
subsystem tried to allocate 2GB or more through malloc. zfs would
attempt such an allocation when run on a system with 2TB or more
of RAM.
Note to self: When this is MFCed, sparc64 needs the same fix.
Differential revision: https://reviews.freebsd.org/D2106
Reviewed by: kib
Reported by: Michael Fuckner <michael@fuckner.net>
Tested by: Michael Fuckner <michael@fuckner.net>
MFC after: 2 weeks
writing approximately never (< 0.00000001% under heavy VM load, and it can
go for months without ever being acquired in normal operation). This
provides a 10% (2-minute) improvement in wall clock time for make -j32
buildworld on a 4-core 32-thread POWER8.
packets and does not schedule interrupts for any packets currently
enqueued. Close two races where enqueued packets may not ever trigger
interrupts. The first of these, at adapter initialization time, was
especially severe since a rush of enqueued packets could actually fill
the receive buffer completely, stalling the interface forever.
MFC after: 2 weeks
This is not complete yet: the gem(4) interface on my laptop seems to
disappear from the PCI bus as a result of quiescing Open Firmware in the
boot loader.
The vtophys() function is used to get the physical page address for
the virtually allocated frame buffers when a physically continuous
memory area is not available. This change also allows removing the
masking of the FB_FLAG_NOMMAP flag in the PS3 syscons driver.
The FB and VT drivers were tested using X.org/xf86-video-scfb and
syscons.
executables. The goal here, not yet accomplished, is to let the e500 kernel
run under QEMU by setting KERNBASE to something that fits in low memory and
then having the kernel relocate itself at runtime.
have the same meaning and occupy the same memory address in the trapframe
courtesy of union. Avoid some pointless #ifdef by spelling them both 'DAR'
in the trapframe.
Fix an extremely subtle concurrency bug triggered by running on 32-thread
POWER8 systems. During thread switch, there was a very small window when
the stack pointer was set to the stack pointer of the outgoing thread, but
after the lock on that thread had already been released.
If, during that window, the outgoing thread were rescheduled on another CPU
and begin execution and an exception were taken on the original CPU, the
trap handler and the outgoing thread would simultaneously execute on the same
stack, causing memory corruption. Fix this by making sure to release the
old thread only after cpu_switch() is done with its stack.
MFC after: 2 weeks
this change is to improve concurrency:
- Drop global state stored in the shadow overflow page table (and all other
global state)
- Remove all global locks
- Use per-PTE lock bits to allow parallel page insertion
- Reconstruct state when requested for evicted PTEs instead of buffering
it during overflow
This drops total wall time for make buildworld on a 32-thread POWER8 system
by a factor of two and system time by a factor of three, providing performance
20% better than similarly clocked Core i7 Xeons per-core. Performance on
smaller SMP systems, where PMAP lock contention was not as much of an issue,
is nearly unchanged.
Tested on: POWER8, POWER5+, G5 UP, G5 SMP (64-bit and 32-bit kernels)
Merged from: user/nwhitehorn/ppc64-pmap-rework
Looked over by: jhibbits, andreast
MFC after: 3 months
Relnotes: yes
Sponsored by: FreeBSD Foundation
and POWER8. This instruction set unifies the 32 64-bit scalar floating
point registers with the 32 128-bit vector registers into a single bank
of 64 128-bit registers. Kernel support mostly amounts to saving and
restoring the wider version of the floating point registers and making
sure that both scalar FP and vector registers are enabled once a VSX
instruction is executed. get_mcontext() and friends currently cannot
see the high bits, which will require a little more work.
As the system compiler (GCC 4.2) does not support VSX, making use of this
from userland requires either newer GCC or clang.
Relnotes: yes
Sponsored by: FreeBSD Foundation
Summary:
Currently, fan control is linear between the target temperature and max
temperature, which is far from ideal. This changes it to be proportional to the
distance between the current temperature and the two endpoints (target and max
temp). This also adds a hysteresis, so that fans keep going when the
temperature drops, for about 10 seconds, before slowing down.
Reviewers: nwhitehorn
Reviewed By: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D1549
MFC after: 3 weeks
Some ATI-based PowerBooks use the string 'mnca' in the backlight controller
device tree entry, so account for this and don't use nVidia when it's not an
nVidia device.
MFC after: 3 weeks
This port failed to gain traction and probably only a couple Wii consoles
ran FreeBSD all the way to single user mode with an md(4). IPC
support was never implemented, so it was impossible to use any peripheral
Any further development, if any, will happen at https://github.com/rpaulo/wii.
Discussed with: nathanw (a long time ago), jhibbits
hypervisor. This prevents an infinite loop where processes with evicted
pages would page fault forever when PMAP decided the evicted pages on
which the process was faulting was actually present and did not need to
be restored.
Found while building LLVM with make -j32.
Sponsored by: FreeBSD Foundation
POWER8 systems. During thread switch, there was a very small window when
the stack pointer was set to the stack pointer of the outgoing thread, but
after the lock on that thread had already been released.
If, during that window, the outgoing thread were rescheduled on another CPU
and begin execution and an exception were taken on the original CPU, the
trap handler and the outgoing thread would simultaneously execute on the same
stack, causing memory corruption. Fix this by making sure to release the
old thread only after cpu_switch() is done with its stack.
MFC after: 2 weeks
Sponsored by: FreeBSD Foundation
every possible trap address by default. This also makes sure the kernel
notices (and panics at) traps from newer CPUs that the kernel was not
expecting rather than executing gibberish memory.
that we (a) get the correct large page size to provide to pmap and (b)
we can alert the user if running under incorrectly-configured PowerKVM
on POWER7 and POWER8 systems.
MFC after: 1 week
const. On x86, even after the machine context is supposedly read into
the struct ucontext, lazy FPU state save code might only mark the FPU
data as hardware-owned. Later, set_fpcontext() needs to fetch the
state from hardware, modifying the *mcp.
The set_mcontext(9) is called from sigreturn(2) and setcontext(2)
implementations and old create_thread(2) interface, which throw the
*mcp out after the set_mcontext() call.
Reported by: dim
Discussed with: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
support in QEMU. Each page of a many page mapping was getting mapped to
the same physical address, which is not the desired behavior.
MFC after: 1 week
A "size" symbol with its address set to the length of handler would be
shifted forward with all other addresses when relocations are processed.
Instead, just note the end and do the subtraction at runtime.
mostly a no-op since all currently-supported instances of these CPUs give
the number of SLB slots in the device tree, but keep it here as well just
in case.
instructions to call through pointers instead. In general, these are set
implicitly through relocation processing. One has to be set explicitly in
machdep.c, however, to fit one handler in the tiny (8 instruction) space
available.
Reviewed by: andreast
Differential revision: D1554
Tested on: UP and SMP G5, Cell, POWER5+
sequences, like are used to read the HIDs. This is both easier to read
and avoids a miscompilation by GCC in certain circumstances. Also avoid
double restoration of HID4 and HID5.
MFC after: 2 weeks
in ofw_mem_regions(). This function is actually MI and should move to
dev/ofw at some point in the near future so that ARM and MIPS can use the
same code.
PVO pool size. The default errs on the exceedingly large side, so absent
any intelligent automatic tuning, at least let the user set it to save
RAM on memory-constrained systems.
MFC after: 2 weeks
This allows executing static clang built with -O0.
The value is configurable by a sysctl, so if one needs to clamp it down, they
still can.
Discussed with: nwhitehorn,emaste
code in sys/kern/kern_dump.c. Most dumpsys() implementations are nearly
identical and simply redefine a number of constants and helper subroutines;
a generic implementation will make it easier to implement features around
kernel core dumps. This change does not alter any minidump code and should
have no functional impact.
PR: 193873
Differential Revision: https://reviews.freebsd.org/D904
Submitted by: Conrad Meyer <conrad.meyer@isilon.com>
Reviewed by: jhibbits (earlier version)
Sponsored by: EMC / Isilon Storage Division
the Open Firmware, as provided by petitboot, for example. Note that this is
not quite complete, since RTAS instantiation still depends on callable
firmware.
MFC after: 2 weeks
It's redundant at the moment since it can be obtained from the trapframe
on the architectures where DTrace is supported, but this won't be the case
with ARM.
WITNESS and INVARIANTS checking, which are known to have significant
performance impact on running systems. When benchmarking new features
this kernel should be used instead of the standard GENERIC.
This kernel configuration should never appear outside of the HEAD
of the FreeBSD tree.
Summary:
Revert the initial FBT-with-KDB changes for trap_subr*.S, and instead use the
db_trap filter function to handle dtrace trap filtering. With this, the MMU is
enabled by the support code, simplifying the codepath altogether.
Test Plan: Tested on my G4 PowerBook
Reviewers: #powerpc, nwhitehorn
Reviewed By: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D1207
MFC after: 3 weeks
It is automatically set when -fPIC is passed to the compiler.
Reviewed by: dim, kib
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D1179
Summary:
Currently if there are problems finding a symbol, backtrace ends up printing
something like:
0xdeadbeef: at +0x12345
Which is pretty useless. This on its own should be fixed (retrieving symbols),
but aside from that, using db_printsym() is a better solution anyway. If it
can't find a valid symbol it prints the actual address, and it has the added
benefit that if it can find the symbol, it might be able to print the file and
line as well.
Test Plan: Tested on my G4 PowerBook
Reviewers: #powerpc, nwhitehorn
Reviewed By: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D1173
MFC after: 3 weeks
have chosen different (and more traditional) stateless/statuful
NAT64 as translation mechanism. Last non-trivial commits to both
faith(4) and faithd(8) happened more than 12 years ago, so I assume
it is time to drop RFC3142 in FreeBSD.
No objections from: net@
of fuword(9) and suword(9). This makes the functions type-compatible
with volatile objects and does not require devolatile force, e.g. in
kern_umtx.c.
Requested by: bde
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
unit 0.
It seems that this 'simplification' was copied to all GPIO drivers in tree.
This fix a bug where a GPIO controller could fail to attach its children
(gpioc and gpiobus) if another GPIO driver attach first.
and casuword(9), but do not mix value read and indication of fault.
I know (or remember) enough assembly to handle x86 and powerpc. For
arm, mips and sparc64, implement fueword() and casueword() as wrappers
around fuword() and casuword(), which means that the functions cannot
distinguish between -1 and fault.
On architectures where fueword() and casueword() are native, implement
fuword() and casuword() using fueword() and casuword(), to reduce
assembly code duplication.
Sponsored by: The FreeBSD Foundation
Tested by: pho
MFC after: 2 weeks (ia64 needs treating)
- Wrong integer type was specified.
- Wrong or missing "access" specifier. The "access" specifier
sometimes included the SYSCTL type, which it should not, except for
procedural SYSCTL nodes.
- Logical OR where binary OR was expected.
- Properly assert the "access" argument passed to all SYSCTL macros,
using the CTASSERT macro. This applies to both static- and dynamically
created SYSCTLs.
- Properly assert the the data type for both static and dynamic
SYSCTLs. In the case of static SYSCTLs we only assert that the data
pointed to by the SYSCTL data pointer has the correct size, hence
there is no easy way to assert types in the C language outside a
C-function.
- Rewrote some code which doesn't pass a constant "access" specifier
when creating dynamic SYSCTL nodes, which is now a requirement.
- Updated "EXAMPLES" section in SYSCTL manual page.
MFC after: 3 days
Sponsored by: Mellanox Technologies
in userland rename in-kernel getenv()/setenv() to kern_setenv()/kern_getenv().
This fixes a namespace collision with libc symbols.
Submitted by: kmacy
Tested by: make universe
For compatibility, 'device windtunnel' is still supported, but one should use
'device adm1030' instead, and this has been updated in GENERIC and NOTES.
Summary:
If a user uses powerd, or doesn't want to use the cycles monitoring, they can
now suspend the monitoring thread.
While here, reorganize the added prototypes to match existing groupings.
Reviewers: nwhitehorn, #powerpc, rpaulo
Reviewed By: #powerpc, rpaulo
Differential Revision: https://reviews.freebsd.org/D944
X-MFC-with: r273009
MFC after: 3 weeks
Summary:
Add a polling loop (1Hz) to monitor the battery and AC status, to notify devd
like ACPI does for power monitoring. This allows /etc/rc.d/power_profile to
work on PowerPC laptops
Test Plan:
Tested on a Titanium PowerBook, configuring economy_cpu_freq and
performance_cpu_freq, disabling powerd.
Reviewers: #powerpc, nwhitehorn
Reviewed By: nwhitehorn
Subscribers: rpaulo
Differential Revision: https://reviews.freebsd.org/D937
node's interrupts=<...> property creating resource list entries with a
single common implementation. This change makes ofw_bus_intr_to_rl() the
one true copy of that code and removes the copies of it from other places.
This also adds handling of the interrupts-extended property, which allows
specifying multiple interrupts for a node where each interrupt can have a
separate interrupt-parent. The bindings for this state that the property
cells contain an xref phandle to the interrupt parent followed by whatever
interrupt info that parent normally expects. This leads to having a
variable number of icells per interrupt in the property. For example you
could have <&intc1 1 &intc2 26 9 0 &intc3 9 4>.
Differential Revision: https://reviews.freebsd.org/D803
When the FreeBSD kernel is loaded from Xen the symtab and strtab are
not loaded the same way as the native boot loader. This patch adds
three new global variables to ddb that can be used to specify the
exact position and size of those tables, so they can be directly used
as parameters to db_add_symbol_table. A new helper is introduced, so callers
that used to set ksym_start and ksym_end can use this helper to set the new
variables.
It also adds support for loading them from the Xen PVH port, that was
previously missing those tables.
Sponsored by: Citrix Systems R&D
Reviewed by: kib
ddb/db_main.c:
- Add three new global variables: ksymtab, kstrtab, ksymtab_size that
can be used to specify the position and size of the symtab and
strtab.
- Use those new variables in db_init in order to call db_add_symbol_table.
- Move the logic in db_init to db_fetch_symtab in order to set ksymtab,
kstrtab, ksymtab_size from ksym_start and ksym_end.
ddb/ddb.h:
- Add prototype for db_fetch_ksymtab.
- Declate the extern variables ksymtab, kstrtab and ksymtab_size.
x86/xen/pv.c:
- Add support for finding the symtab and strtab when booted as a Xen
PVH guest. Since Xen loads the symtab and strtab as NetBSD expects
to find them we have to adapt and use the same method.
amd64/amd64/machdep.c:
arm/arm/machdep.c:
i386/i386/machdep.c:
mips/mips/machdep.c:
pc98/pc98/machdep.c:
powerpc/aim/machdep.c:
powerpc/booke/machdep.c:
sparc64/sparc64/machdep.c:
- Use the newly introduced db_fetch_ksymtab in order to set ksymtab,
kstrtab and ksymtab_size.
than u_char.
Migrate post_filter to use an int for a CPU rather than u_char.
Change intr_event_bind() to use an int for CPU rather than u_char.
It touches the ppc, sparc64, arm and mips machdep code but it should
(hah!) be a no-op.
Tested:
* i386, AMD64 laptops
Reviewed by: jhb
physical address of the page to direct map address, in case
SFBUF_OPTIONAL_DIRECT_MAP returns true. The case of PowerPC AIM
64bit, where the page physical address is identical to the direct map
address, is accidental.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
mapping size (currently unused). The flags includes the fault access
bits, wired flag as PMAP_ENTER_WIRED, and a new flag
PMAP_ENTER_NOSLEEP to indicate that pmap should not sleep.
For powerpc aim both 32 and 64 bit, fix implementation to ensure that
the requested mapping is created when PMAP_ENTER_NOSLEEP is not
specified, in particular, wait for the available memory required to
proceed.
In collaboration with: alc
Tested by: nwhitehorn (ppc aim32 and booke)
Sponsored by: The FreeBSD Foundation and EMC / Isilon Storage Division
MFC after: 2 weeks
The MD allocators were very common, however there were some minor
differencies. These differencies were all consolidated in the MI allocator,
under ifdefs. The defines from machine/vmparam.h turn on features required
for a particular machine. For details look in the comment in sys/sf_buf.h.
As result no MD code left in sys/*/*/vm_machdep.c. Some arches still have
machine/sf_buf.h, which is usually quite small.
Tested by: glebius (i386), tuexen (arm32), kevlo (arm32)
Reviewed by: kib
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
We continue to use pmap_enter() for that. For unwiring virtual pages, we
now use pmap_unwire(), which unwires a range of virtual addresses instead
of a single virtual page.
Sponsored by: EMC / Isilon Storage Division
by the combination of r268591 and r269134: When we attempt to add the
wired attribute to an existing mapping, moea{,64}_pvo_enter() do nothing.
(They only set the wired attribute on newly created mappings.)
Tested by: andreast
pmap_unwire(), the call to MOEA64_PVO_TO_PTE() must be performed before
any changes are made to the PVO. Otherwise, MOEA64_PVO_TO_PTE() will
panic.
Reported by: andreast
rebased to point to the allocated memory, but for architectures
that have non-zero relocation addends, the address comparison
happens on the "unfinalized" address.
After the addend is taken into account, call elf_relocaddr() to
make sure we rebase properly.
This commit does not add error returns to minidumpsys() or
textdump_dumpsys(); those can also be added later.
Submitted by: Conrad Meyer (EMC / Isilon storage division)
calling mmap on /dev/mem and add a handler for the possible userland
machine checks that may result. Remove some pointless and wrong copy/paste
that has been in here for a decade as well.
This results in a /dev/mem with identical semantics to the x86 version.
MFC after: 1 week
the upstream implementation and helps ensure that a trap induced by tracing
fbt::trap:entry is handled without recursively generating another trap.
This makes it possible to run most (but not all) of the DTrace tests under
common/safety/ without triggering a kernel panic.
Submitted by: Anton Rang <anton.rang@isilon.com> (original version)
Phabric: D95
entry was being tested. We were incrementing and decrementing the pmap's
wired mapping count based on whether the physical page being mapped or
unmapped was cache coherent, not whether it was a wired mapping.
Reviewed by: nwhitehorn
was not allocating space for the parameter save area in the stack frame.
If the compiler chose to save the argument to the signal handler on the
stack, it would overwrite the first 32 bits of the sigaction struct with
it, corrupting it for a subsequent invocation.
PR: powerpc/183040
MFC after: 8 days
1. Make sure IPI mask is set before sending the IPI
2. Operate atomically on PS3 PIC outstanding interrupt list
3. Make sure IPIs are EOI'ed before, not after, processing. Without this,
a second IPI could be sent partway through processing the first one,
get erroneously acknowledge by the EOI to the first, and be lost. In
particular in the case of smp_rendezvous(), this can be fatal.
In combination, this makes the PS3 boot SMP again. It probably also fixes
some latent bugs elsewhere.
MFC after: 2 weeks
multiuser again (this commit comes from the PS3 itself). Some problems
still exist with SMP, apparently, as I had to boot a non-SMP kernel to
get here.
GENERIC64 for PowerPC to use vt with it.
Much to my chagrin, PS3 support seems to have bitrotted somewhat since the
last time I tried it. ehci panics on attach and interrupt handling seems
to be faulty. This should be fixed soon...
the cpufreq code. Replace its use with smp_started. There's at least
one userland tool that still looks at the kern.smp.active sysctl, so
preserve it but point it to smp_started as well.
Discussed with: peter, jhb
MFC after: 3 days
Obtained from: Netflix
with the ATI Radeon 9700 in the PowerBook G4 1.67GHz.
Code shamelessly taken in spirit from the radeonkms driver, which I hope will
make this driver redundant in the future.
MFC after: 2 weeks
To reduce the diff struct pcu.cnt field was not renamed, so
PCPU_OP(cnt.field) is still used. pc_cnt and pcpu are also used in
kvm(3) and vmstat(8). The goal was to not affect externally used KPI.
Bump __FreeBSD_version_ in case some out-of-tree module/code relies on the
the global cnt variable.
Exp-run revealed no ports using it directly.
No objection from: arch@
Sponsored by: EMC / Isilon Storage Division
This appears to fix a strange condition with X on 32-bit PowerBooks I observed,
caused by one of these bits getting set in the mcontext, but not set in the
thread, which may be a symptom of another problem, more difficult to diagnose.
Since these bits aren't exported anyway, this change makes it more explicit that
the bits aren't MSR-related in SRR1.
MFC after: 3 weeks
The NetBSD Foundation states "Third parties are encouraged to change the
license on any files which have a 4-clause license contributed to the
NetBSD Foundation to a 2-clause license."
This change removes clauses 3 and 4 from copyright / license blocks that
list The NetBSD Foundation as the only copyright holder.
Sponsored by: The FreeBSD Foundation
a sub-node of nexus (ofwbus) rather than direct attach under nexus. This
fixes FDT on x86 and will make coexistence with ACPI on ARM systems easier.
SPARC is unchanged.
Reviewed by: imp, ian
CAPABILITIES stuff required to make ssh work.
Hopefully, Book-E can eventually be added to GENERIC, which would avoid
this kind of issue with bitrot. That will require figuring out how to link
Book-E and AIM kernels at the same address, however...
strings and include arbitrary information (IRQ line/domain/sense). When the
ofw_bus_map_intr() API was introduced, it assumed that, as on most systems,
these were either 1 cell, containing an interrupt line, or 2, containing
a line number plus a sense code. It turns out a non-negligible number of
ARM systems use 3 (or even 4!) cells for interrupts, so make this more
general.
This also fixes asserts on removal of the module for the mpc74xx.
The PowerPC 970 processors have two different types of events: direct events
and indirect events. Thus far only direct events are supported. I included
some documentation in the driver on how indirect events work, but support is
for the future.
MFC after: 1 month
macro was changed. Since copying 64-bit srr1 into 32-bit srr1 drops the upper
32 bits, any bits set in the context were dropped, meaning the context check
fails. Since 32-bit set_context can't change those bits anyway, copy the ones
from the current context (td->td_frame) before calling set_context().
MFC after: 3 weeks
This is the first step needed to get the snapper codec working on those
machines.
The second step is to enable the corresponding I2S device and its clock.
Tested on machines where the snapper codec was already working, a G4 PowerBook
and a PowerMac9,1 with a Shasta based macio.
The PowerMac7,2/7,3 with a K2 based macio can now also play sound.
MFC after: 1 month
obsolete. This involves the following pieces:
- Remove it entirely on PowerPC, where it is not used by MD code either
- Remove all references to machine/fdt.h in non-architecture-specific code
(aside from uart_cpu_fdt.c, shared by ARM and MIPS, and so is somewhat
non-arch-specific).
- Fix code relying on header pollution from machine/fdt.h includes
- Legacy fdtbus.c (still used on x86 FDT systems) now passes resource
requests to its parent (nexus). This allows x86 FDT devices to allocate
both memory and IO requests and removes the last notionally MI use of
fdtbus_bs_tag.
- On those architectures that retain a machine/fdt.h, unused bits like
FDT_MAP_IRQ and FDT_INTR_MAX have been removed.
This, and several subsequent commits, are suspend/resume for various PowerMac
drivers, which will include a change to the global suspend/resume code
eventually.
With this, also shut shut off the display (DPMS-style) and disable the clocking
when the backlight level is set to 0. This is taken from the radeonkms driver
(radeon_legacy_encoders.c) which doesn't yet support PowerPC, and won't for a
while, as it's missing full AGP support.
containing the trap instruction encoding (0x7c810808), and restoring it back
with the frame on return. This caused it to panic on my ppc32 machine, but
somehow my ppc64 machine overlooked it, because I was using such a simple
dtrace probe.
X-MFC-with: r259245
MFC after: 2 weeks
regions which represent the total amount of memory. The size of these regions
is not the physical size of the chip but it is a logical one and it is given
by the OpenFirmware, it is selectable at boot time and varies between 16MB and
256MB in my case. There is an 'automatic' option which would select the size as
64MB in case you have around 16GB of RAM.
To make sure we can allocate RAM with the automatic option bump this value
of PHYS_AVAIL_SZ to 256.
Open Firmware-centric:
- Keep the static list of regions in platform.c instead of ofw_machdep.c
- Move various merging and sorting operations to platform.c as well
- Move apple_hacks code out of ofw_machdep.c and into platform_powermac.c,
where it belongs
- Move CHRP-specific dynamic-reconfiguration memory parsing into
platform_chrp.c instead of pretending it is shared code
shifts into the sign bit. Instead use (1U << 31) which gets the
expected result.
This fix is not ideal as it assumes a 32 bit int, but does fix the issue
for most cases.
A similar change was made in OpenBSD.
Discussed with: -arch, rdivacky
Reviewed by: cperciva
requires process descriptors to work and having PROCDESC in GENERIC
seems not enough, especially that we hope to have more and more consumers
in the base.
MFC after: 3 days
from OF. Linux does it similar, means they also read the OF values and
display them.
Tested under qemu and real hardware:
cpu0: IBM POWER5+ revision 2.0, 1898.10 MHz
preserve any existing fault buffer. RTAS calls are meant to be safe from
interrupt context (and are indeed used there to implement the xics PIC
drvier). Without this, calling into RTAS in interrupt context would have
the effect of clearing any existing onfault state of the interrupted
thread, potentially leading to a panic.
option, unbreak the lock tracing release semantic by embedding
calls to LOCKSTAT_PROFILE_RELEASE_LOCK() direclty in the inlined
version of the releasing functions for mutex, rwlock and sxlock.
Failing to do so skips the lockstat_probe_func invokation for
unlocking.
- As part of the LOCKSTAT support is inlined in mutex operation, for
kernel compiled without lock debugging options, potentially every
consumer must be compiled including opt_kdtrace.h.
Fix this by moving KDTRACE_HOOKS into opt_global.h and remove the
dependency by opt_kdtrace.h for all files, as now only KDTRACE_FRAMES
is linked there and it is only used as a compile-time stub [0].
[0] immediately shows some new bug as DTRACE-derived support for debug
in sfxge is broken and it was never really tested. As it was not
including correctly opt_kdtrace.h before it was never enabled so it
was kept broken for a while. Fix this by using a protection stub,
leaving sfxge driver authors the responsibility for fixing it
appropriately [1].
Sponsored by: EMC / Isilon storage division
Discussed with: rstone
[0] Reported by: rstone
[1] Discussed with: philip
It turned out that on pSeries machines the call into OF modified the trap
vectors and this made further behaviour unpredictable.
With this commit I'm now able to boot multi user on a network booted
environment on my IntelliStation 285. This is a POWER5+ machine.
Discussed with: nwhitehorn
MFC after: 1 week
ibm,dma-window properties. This is especially a concern when
#ibm,dma-address-cells is not specified and we have to use the regular
#address-cells property.
MFC after: 1 week
On some machines (G5 with lots of RAM), entering OF sometimes causes the
machine to hang. Once the machine is booted, currently the only entry point
into OF is through resetting the framebuffer on mode switch on these machines.
Disabling this allows the machine to stay up at the expense of less usable
consoles after X is started.
MFC after: Never, this is only a hack
some comment I wrote about these values "lying" in the negative diff, which
referes to an earlier misunderstanding about which node to read them from.
This gets at least the PPC64 kernel booting in the mac99 system model in
QEMU after bypassing the MacIO ATA driver, which apparently still has
problems.
allows FPU emulation on AIM as well as providing support for the mfpvr
and lwsync instructions from userland on e500 cores. lwsync, in particular,
is required for many C++ programs to work correctly.
MFC after: 1 week
the actual FPU is enabled, while PCB_FPREGS indicates that the FPU state
structure in the PCB is valid. This separation reflects the situation on
FPU-less systems in which the FP state is used by the emulator but we don't
actually want to try to turn on the non-existant FPU.
Use this flag to save and restore FP regs properly on both AIM and Book-E.
As a side effect, this sets up hard-FP and Altivec on Book-E CPUs with such
abilities except for a trap handler to call enable_fpu()/enable_altivec().
it never did -- and fix an obvious missing line. Floating point emulation
on Book-E still needs some work but this gets it basically functional on
soft-FPU systems (hard FPU for Book-E is not yet implemented).
MFC after: 1 week
it more flexible about how the CCSR range is found. With this change, the
stock MPC85XX will boot on a Routerboard 800.
Hardware donated by: Benjamin Perrault
I found a stack overflow when a coredump was taken onto a ZFS volume with
heavy network activity. 2 DSI traps, plus one DECR trap, along with several
function calls in the stack, overflowed the 4 pages. 8 page stack fixes this.
Discussed with: nwhitehorn
MFC after: 1 week
a variant PCI bus instead of trying to shoehorn it into the PCI host bridge
adapter. Besides matching better the architecture on other platforms, this
also allows systems with multiple partitionable endpoints per PCI host
bridge to work correctly.
PCPU fields for curthread, by doing the same to Book-E. This closes
some potential races switching between CPUs. As a side effect, it turns out
the AIM and Book-E swtch.S implementations were the same to within a few
registers, so move that to powerpc/powerpc.
MFC after: 3 months
add actual platform probing based on PVR. Still needs a little more work:
in particular, the CCRS setup should move here.
Also turn "bare" into a truly bare platform that doesn't pretend to know how
to do anything except get the memory map. This should also be enhanced to
process the FDT reserved memory list, but that is for another day.
assumed that the MDIO bus was a direct child of the Ethernet interface. It
may not be and indeed on many device trees is not. While here, add proper
locking for MII transactions, which may be on a bus shared by several MACs.
Hardware donated by: Benjamin Perrault
words, every architecture is now auto-sizing the kmem arena. This revision
changes kmeminit() so that the definition of VM_KMEM_SIZE_SCALE becomes
mandatory and the definition of VM_KMEM_SIZE becomes optional.
Replace or eliminate all existing definitions of VM_KMEM_SIZE. With
auto-sizing enabled, VM_KMEM_SIZE effectively became an alternate spelling
for VM_KMEM_SIZE_MIN on most architectures. Use VM_KMEM_SIZE_MIN for
clarity.
Change kmeminit() so that the effect of defining VM_KMEM_SIZE is similar to
that of setting the tunable vm.kmem_size. Whereas the macros
VM_KMEM_SIZE_{MAX,MIN,SCALE} have had the same effect as the tunables
vm.kmem_size_{max,min,scale}, the effects of VM_KMEM_SIZE and vm.kmem_size
have been distinct. In particular, whereas VM_KMEM_SIZE was overridden by
VM_KMEM_SIZE_{MAX,MIN,SCALE} and vm.kmem_size_{max,min,scale}, vm.kmem_size
was not. Remedy this inconsistency. Now, VM_KMEM_SIZE can be used to set
the size of the kmem arena at compile-time without that value being
overridden by auto-sizing.
Update the nearby comments to reflect the kmem submap being replaced by the
kmem arena. Stop duplicating the auto-sizing formula in every machine-
dependent vmparam.h and place it in kmeminit() where auto-sizing takes
place.
Reviewed by: kib (an earlier version)
Sponsored by: EMC / Isilon Storage Division
fdtbus in most cases. This brings ARM and MIPS more in line with existing
Open Firmware platforms like sparc64 and powerpc, as well as preventing
double-enumeration of the OF tree on embedded PowerPC (first through nexus,
then through fdtbus).
This change is also designed to simplify resource management on FDT platforms
by letting there exist a platform-defined root bus resource_activate() call
instead of replying on fdtbus to do the right thing through fdt_bs_tag.
The OFW_BUS_MAP_INTR() and OFW_BUS_CONFIG_INTR() kobj methods are also
available to implement for similar purposes.
Discussed on: -arm, -mips
Tested by: zbb, brooks, imp, and others
MFC after: 6 weeks
corresponding x86 trap type. Userland DTrace probes are currently handled
by the other fasttrap hooks (dtrace_pid_probe_ptr and
dtrace_return_probe_ptr).
Discussed with: rpaulo
the upper 32-bits of the LUN, if possible, into the target_lun field as
passed directly from the REPORT LUNs response. This allows extended LUN
support to work for all LUNs with zeros in the lower 32-bits, which covers
most addressing modes without breaking KBI. Behavior for drivers not
setting PIM_EXTLUNS is unchanged. No user-facing interfaces are modified.
Extended LUNs are stored with swizzled 16-bit word order so that, for
devices implementing LUN addressing (like SCSI-2), the numerical
representation of the LUN is identical with and without PIM_EXTLUNS. Thus
setting PIM_EXTLUNS keeps most behavior, and user-facing LUN IDs, unchanged.
This follows the strategy used in Solaris. A macro (CAM_EXTLUN_BYTE_SWIZZLE)
is provided to transform a lun_id_t into a uint64_t ordered for the wire.
This is the second part of work for full 64-bit extended LUN support and is
designed to a bridge for stable/10 to the final 64-bit LUN code. The
third and final part will involve widening lun_id_t to 64 bits and will
not be MFCed. This third part will break the KBI but will keep the KPI
unchanged so that all drivers that will care about this can be updated now
and not require code changes between HEAD and stable/10.
Reviewed by: scottl
MFC after: 2 weeks
vm_pages. Provide trivial implementation which forwards the load to
_bus_dmamap_load_phys() page by page. Right now all architectures use
bus_dmamap_load_ma_triv().
Tested by: pho (as part of the functional patch)
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
previous KVA allocations (which the PMAP lazily invalidates) in TLB0 could
shadow device maps in TLB1. Add a big block comment about some of the
caveats with this approach.
device tree into r3. Rather than worrying about mapping that tree, reserving
its space in the global physical memory space, etc., just copy it to some
memory after the kernel.
- Remove explicit requirement that the SOC registers be found except as an
optimization (although the MPC85XX LAW drivers still require they be found
externally, which should change).
- Remove magic CCSRBAR_VA value.
- Allow bus_machdep.c's early-boot code to handle non 1:1 mappings and
systems not in real-mode or global 1:1 maps in early boot.
- Allow pmap_mapdev() on Book-E to reissue previous addresses if the
area is already mapped. Additionally have it check all mappings, not
just the CCSR area.
This allows the console on e500 systems to actually work on systems where
the boot loader was not kind enough to set up a 1:1 mapping before starting
the kernel.
Use it universally. Book-E traps may also need revisiting due to the
introduction of fixed-offset traps and the deprecation of IVORs in POWER
ISA 2.06, but that's very much an issue for another day.
is slightly more complicated and is left unimplemented for now. Also
prevent pmap_mapdev() from mapping over the kernel and KVA regions if
devices happen to have high physical addresses.
MFC after: 2 weeks
crazy readings occasionally. One wild reading should not be enough to
trigger a shutdown, so instead wait for several concerning readings in
a row.
PR: powerpc/180593
Submitted by: Julio Merino
MFC after: 1 week
- ofw_bus_map_intr()
Maps an (iparent, IRQ) tuple to a system-global interrupt number in some
platform dependent way. This is meant to be implemented as a replacement
for [FDT_]MAP_IRQ() that is an MI interface that knows about the bus
hierarchy.
- ofw_bus_config_intr()
Configures an interrupt (previously mapped) based on firmware sense flags.
This replaces manual interpretation of the sense field in bus drivers and
will, in a follow-up, allow that interpretation to be redirected to the PIC
drivers where it belongs. This will eventually replace the tables in
/sys/dev/fdt/fdt_ARCH.c
The PowerPC/AIM code has been converted to use these globally, with an
implementation in terms of MAP_IRQ() and powerpc_config_intr(), assuming
OpenPIC, at the bus root in nexus(4). The ofw_bus_config_intr() will shortly
be integrated into pic_if.m and bounced through nexus into the PIC tree.
FDT integration will happen significantly later due to larger testing
requirements. This patch in general also lays the groundwork for the removal
of /sys/dev/fdt/fdt_ARCH.c and machine/fdt.h.
