- Clear PCIM_CMD_MWRICEN:
some chips seem to have problem with write invalidate.
clearing this bit fixes SBP timeout problem.
Tested by: Michael Reifenberger <Michael.Reifenberger@Plaut.de>
- Set PCIM_CMD_SERRESPEN and PCIM_CMD_PERRESPEN
- Moderate value for latency timer.
in geom_disk.c.
As a side effect this makes a lot of #include <sys/devicestat.h>
lines not needed and some biofinish() calls can be reduced to
biodone() again.
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
This should fix some problem of SBP2 device probing.
Prior to rev 1.41, we keep writing the register while bus reset phase.
But in rev 1.41, we ignore successive bus reset events and some chips seem to
clear the register after we write to it.
Tested by: Michael Reifenberger <root@nihil.reifenberger.com>
Improve SBP device probeing:
- Wait 2 sec before issuing LOGIN ORB expecting the reconnection
hold timer expires.
- Serialize management ORB and scanning LUN by CAM on each target.
This should fix the problem for devices which have multiple LUNs.
Test device is donated by: Jaye Mathisen <mrcpu@internetcds.com>
- Freeze SIM queue for 2 sec after BUS RESET.
- Retry with LOGIN rather than RECONNECT after LOGIN is not completed for
BUS RESET.
- Use appropriate CAM status for BUS RESET and DEVICE RESET.
- Let CAM to scan targets after BUS REST.
- Implement CAM scan target function.
- Keep our own devq freeze count.
- Let CAM to know that SBP does tagged queuing.
These should be merged to RELENG_4 before 4.8-RELEASE.
- Get rid of the useless atop() / pmap_phys_address() detour. The
device mmap handlers must now give back the physical address
without atop()'ing it.
- Don't borrow the physical address of the mapping in the returned
int. Now we properly pass a vm_offset_t * and expect it to be
filled by the mmap handler when the mapping was successful. The
mmap handler must now return 0 when successful, any other value
is considered as an error. Previously, returning -1 was the only
way to fail. This change thus accidentally fixes some devices
which were bogusly returning errno constants which would have been
considered as addresses by the device pager.
- Garbage collect the poorly named pmap_phys_address() now that it's
no longer used.
- Convert all the d_mmap_t consumers to the new API.
I'm still not sure wheter we need a __FreeBSD_version bump for this,
since and we didn't guarantee API/ABI stability until 5.1-RELEASE.
Discussed with: alc, phk, jake
Reviewed by: peter
Compile-tested on: LINT (i386), GENERIC (alpha and sparc64)
Runtime-tested on: i386
Some drives seem to be confused by simultaneous probes.
Tested by: marcel
As a side effect, logical units whose lun is greater than 0 might not be
probed correctly if the lun of 0 doesn't exist in the target because
CAM doesn't scan such luns.
I have a SCSI-FireWire bridge which maps SCSI-ID to LUN and it is an
example of such targets.
- Fix memory leak in detaching.
- Initialize fc->status to other than FWBUSREST.
* fwohci.c
- Ignore BUS reset events while BUS reset phase. We can't clear that flag
during bus reset phase.
- Don't initiate bus reset even if probe failed for some nodes to prevent
infinite bus reset loop.
Problem Reported by: Pierre Beyssac <pb@fasterix.frmug.org>
- Protect timeout routine with splfw() for 4-stable.
* sbp.c
- Make sure to release devq when start request.
previous revision fixed the panic, I found the problem exits in
another part of the function by investigating the crom dump sent by him.
The search was started in the middle of bus info block and the
routine misunderstood the EUI64 as a crom entry. This problem is fixed.
PR: kern/48129
Fix incorrect type mask included in a logical unit number and check
the validity of the lun.
- Drain fwohci TX queue first then drain xfer queue which has not started.
- Check validity of the received packet length.
- Don't allocate too large buffer for xfer receive buf.
sbp
- Fix panic for some CROM which doesn't have a text leaf.
This could fix the PR kern/48129 but no feedback has been gotten from
the originator yet.
- Put back some M_NOWAIT flags into malloc which could be called
in interrupt context for 4-stable.
* implement watchdog timer.
* check all standing transactions in firewire_xfer_timeout().
- Add firewire_xferq_drain() for fw_busreset().
- Add/improve some debug messages.
- Call fw_xfer_done() if retry handler is NULL.
- Fix overwrite problem of freed buffers. It was rare but could happen
when fwohci_arcv() is called before fwohci_txd() is called for
the transcation.
- Drain AT queues and pend AR queues on SID receive rather than BUS reset to
make sure DMA actually stops.
- Do agent reset in sbp_timeout().
