case where the controller is already enabled.
Some of the pl310 configuration registers cannot be changed while the
controller is active, so if there is any platform-specific init to be done
it must happen before enabling the controller.
The controller should not be enabled upon entry to the kernel, but u-boot
has recently developed the bad habit of leaving caches enabled when
launching the kernel, and since we have no control over that source code
we have to do our best to cope with it. The PL310 manual doesn't document
a safe sequence for disabling the controller, but the sequence used here
(force write-through mode and disable linefill allocations, then clean and
invalidate the current contents before disabling the hardware) appears to
be sound both by analysis and empirical testing.
These changes were developed and tested in collaboration with
Svatopluk Kraus <onwahe@gmail.com>.
Reviewed by: cognet@
controller driver by piggybacking the SOF interrupt when issuing new
and checking old transfers. Number of interrupts was reduced by 30%
when doing Isochronous transfers.
Use correct GINTMSK_XXX macros when accessing the DWC OTG interrupt
mask register.
Add code to adjust the frame interval register which influences the
SOF rate.
MFC after: 2 weeks
This problem only occurs on versions of FreeBSD prior to the recent CAM
locking changes. (i.e. stable/9 and older versions of stable/10) This
change should be a no-op for head and stable/10.
If a path isn't specified, xpt_register_async() will create a fully
wildcarded path and acquire a lock (the XPT lock in older versions,
and via xpt_path_lock() in newer versions) to call xpt_action() for the
XPT_SASYNC_CB CCB. It will then drop the lock and if the requested event
includes AC_FOUND_DEVICE or AC_PATH_REGISTERED, it will get the caller up
to date with any device arrivals or path registrations.
The issue is that before the locking changes, each SIM lock would get
acquired in turn during the EDT tree traversal process. If a path is
specified for xpt_register_async(), it won't acquire and drop its own lock,
but instead expects the caller to hold its own SIM lock. That works for
the first part of xpt_register_async(), but causes a recursive lock
acquisition once the EDT traversal happens and it comes to the SIM in
question. And it isn't possible to call xpt_action() without holding a SIM
lock.
The locking changes fix this by using the XPT topology lock for EDT
traversal, so it is no longer an issue to hold the SIM lock while calling
xpt_register_async().
The solution for FreeBSD versions before the locking changes is to request
notification of all device arrivals (so we pass a NULL path into
xpt_register_async()) and then filter out the arrivals that are not ours.
MFC After: 3 days
Sponsored by: Spectra Logic Corporation
periodically update the reference status of the active pages. This function
was called, instead of vm_pageout_scan(), when memory was not scarce. The
objective was to provide up to date reference status for active pages in
case memory did become scarce and active pages needed to be deactivated.
The active page queue scan performed by vm_pageout_page_stats() was
virtually identical to that performed by vm_pageout_scan(), and so r254304
eliminated vm_pageout_page_stats(). Instead, vm_pageout_scan() is
called with the parameter "pass" set to zero. The intention was that when
pass is zero, vm_pageout_scan() would only scan the active queue. However,
the variable page_shortage can still be greater than zero when memory is not
scarce and vm_pageout_scan() is called with pass equal to zero.
Consequently, the inactive queue may be scanned and dirty pages laundered
even though that was not intended by r254304. This revision fixes that.
Reported by: avg
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
used.
It turns out that the RX DMA engine does the same last-descriptor-link-
pointer-re-reading trick that the TX DMA engine. That is, the hardware
re-reads the link pointer before it moves onto the next descriptor.
Thus we can't free a descriptor before we move on; it's possible the
hardware will need to re-read the link pointer before we overwrite
it with a new one.
Tested:
* AR5416, STA mode
TODO:
* more thorough AP and STA mode testing!
* test on other pre-AR9380 NICs, just to be sure.
* Break out the RX descriptor grabbing bits from the RX completion
bits, like what is done in the RX EDMA code, so ..
* .. the RX lock can be held during ath_rx_proc(), but not across
packet input.
same events that tcpstat's tcps_rcvmemdrop counter counts.
- Rename tcps_rcvmemdrop to tcps_rcvreassfull and improve its
description in netstat(1) output.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
thicket of .if ${COMPILER_TYPE} == "clang" that controls
warnings. Also, use CFLAGS.clang in a couple places in preference to
having a similar construct that's related to the CWARNFLAGS changes.
o Declare vt(4) drivers dataset.
o Create single static structures for all early drivers.
o Add vt(4) to be by default in the kernel consoles list.
o Create one more sysinit point, to be able to initialize memory and lock
requirement of early drivers.
o Implement early drivers select. (Only best available will be selected).
o Fix one missed "return (0)" for VTYLOCK.
o Improve locking for cases when one driver replace another.
o Make driver replacement notification less debug-look-like.
Minor spell fixes.
Sponsored by: The FreeBSD Foundation
reflect when unmapped I/O support was added.
For FreeBSD 10, it arrived just prior to __FreeBSD_version 1000028.
For FreeBSD 9, it arrived just prior to __FreeBSD_version 902001.
Also, fix compiler warnings in mprsas_send_smpcmd() that happen in the
i386 PAE build for non-unmapped I/O builds. These were fixed in mps(4)
in revision 241145, but didn't make it into the mpr(4) driver. This
change should only affect FreeBSD versions outside the above revisions,
and thus doesn't affect head.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
rman_reserve_resource_bound() to return incorrect results.
Continue the initial search until the first viable region is found.
Add a comment to explain the search termination test.
PR: kern/188534
Reviewed by: jhb (previous version)
MFC after: 1 week
platforms, because these platforms do not implement the ISA DMA
API. Else the sound modules cannot be loaded when running these
platforms.
MFC after: 2 weeks
speed data traffic going directly to a USB device or through a
so-called USB transaction translator.
Add checks that we are not overusing the TX FIFO.
MFC after: 2 weeks
the provider - also apply to UFS1 filesystems. This should help with
resizing filesystems created by makefs(8), which still uses UFS1.
Tested by: jmg@
Sponsored by: The FreeBSD Foundation
call, which assumes the hardware is awake.
Turn ath_update_mcast() into a routine that's only called from the
net80211 layer - and it forces the hardware awake first.
This fixes a LOR from the EDMA RX path which calls ath_mode_init()
with the RX lock held - the driver lock can't also be grabbed.
This path assumes that the ath_mode_init() callers all wake up
the NIC first.
Tested:
* AR9485, STA mode, powersave
This seems to probe/attach as an AR9485 and thus nothing else besides
adding the device id seems to be required.
ath0: <Atheros AR1111> mem 0xf4800000-0xf487ffff irq 19 at device 0.0 on pci5
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9485 mac 576.1 RF5110 phy 1926.8
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
The NIC I have here is a 1 antenna, 2GHz only device.
Thankyou to Jim Thompson <jim@netgate.com> for the AR1111 NIC.
Tested:
* AR1111 (pretending not to be an AR9485, but failing miserably);
STA mode with powersave.
Relnotes: yes
Sponsored by: Netgate
mixing on stack memory and UMA memory in one linked list.
Thus, rewrite TCP reassembly code in terms of memory usage. The
algorithm remains unchanged.
We actually do not need extra memory to build a reassembly queue.
Arriving mbufs are always packet header mbufs. So we got the length
of data as pkthdr.len. We got m_nextpkt for linkage. And we need
only one pointer to point at the tcphdr, use PH_loc for that.
In tcpcb the t_segq fields becomes mbuf pointer. The t_segqlen
field now counts not packets, but bytes in the queue. This gives
us more precision when comparing to socket buffer limits.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
freebsd-current. These CPU speed control techniques are usually unhelpful
at best. For now, continue building the relevant code into GENERIC so that
it can trivially be re-enabled at runtime if anyone wants it.
MFC after: 1 month
cause stack overflow for IO's which return ZIO_PIPELINE_CONTINUE
from the zio_vdev_io_start stage and hence don't suspend and complete
in a different thread.
This prevents double fault panic on slow machines running ZFS on
GELI volumes which return EOPNOTSUPP directly to BIO_DELETE requests.
MFC after: 1 month
X-MFC-With: r265152
sys/systm.h must always come after sys/param.h.
Remove sys/types.h which should never be included together with sys/param.h.
Add sys/malloc.h for correctness even if it seems to don't be needed.
Remove more unused headers found by unusedinc (from bde@) and tested with a
universe build.
Reported by: bde
It looks like current consumers are either unaware
of MRT (and uses RT_DEFAULT_FIB implicitly) or
know what thay are doing, In latter case they
will be either hit by KASSERT or ESCRH will be returned
due to NULL rnh.
disk. That has a side effect of corrupting the "." entries names on
rename, since the call to createde() in the msdosfs_rename() sets the
de_Name to the target name. If any change to the directory attributes
is performed, the wrong name is written back to the on-disk direntry
on update.
Overwrite the de_Name for the directories on rename to correct the dot
name.
Submitted by: bde
MFC after: 1 week
This allows to run 32bit applications on a 64bit host. This was tested
successfully with Wine (emulators/i386-wine-devel) and StarCraft II.
Submitted by: Jan Kokemüller <jan.kokemueller@gmail.com>
MFC after: 1 week
should either accept owner and owner_group strings that are just
the digits of the uid/gid or return NFS4ERR_BADOWNER.
This patch adds a sysctl vfs.nfsd.enable_stringtouid, which can
be set to enable the server w.r.t. accepting numeric string. It
also ensures that NFS4ERR_BADOWNER is returned if numeric uid/gid
strings are not enabled. This fixes the server for recent Linux
nfs4 clients that use numeric uid/gid strings by default.
Reported and tested by: craigyk@gmail.com
MFC after: 2 weeks
This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.
Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.
o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.
o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.
Thanks to LSI for developing and testing this driver for FreeBSD.
share/man/man4/mpr.4:
mpr(4) man page.
sys/dev/mpr/*:
mpr(4) driver files.
sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.
sys/conf/files:
Add the mpr(4) driver.
sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.
sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.
sys/i386/conf/XEN:
Exclude the mpr module from building here.
Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added
The thread that is destroying the lagg has already set sc->sc_psc=NULL when
the "ifconfig -am" thread gets to lacp_req(). It tries to dereference
sc->sc_psc and panics. The solution is for lacp_req() to check the value of
sc->sc_psc. If NULL, harmlessly return an lacp_opreq structure full of
zeros. Full details in GNATS.
PR: kern/189003
Reviewed by: timeout on freebsd-net@
MFC after: 3 weeks
Sponsored by: Spectra Logic Corporation
for lockmgr and sx interlocks, but unused since optimised versions of
those sleep locks were introduced. This will save a (quite) small
amount of memory in all kernel configurations. The sleep mutex pool is
retained as it is used for 'struct bio' and several other consumers.
Discussed with: jhb
MFC after: 3 days
lindev(4) was only used to provide /dev/full which is now a standard feature of
FreeBSD. /dev/full was never linux-specific and provides a generally useful
feature.
Document this in UPDATING and bump __FreeBSD_version. This will be documented
in the PH shortly.
Reported by: jkim
lindev(4) was only used to provide /dev/full which is now a standard feature of
FreeBSD. /dev/full was never linux-specific and provides a generally useful
feature.
Document this in UPDATING and bump __FreeBSD_version. This will be documented
in the PH shortly.
Reported by: jkim
Adjust the exynos and zedboard dts files to use max-frequency (the
documented standard property) instead of clock-frequency.
Submitted by: Thomas Skibo <ThomasSkibo@sbcglobal.net>
It can fail if pipe map is exhausted (as a result of too many pipes created),
but it is not fatal and could be provoked by unprivileged users. The only
consequence is worse performance with given pipe.
Reported by: ivoras
Suggested by: kib
MFC after: 1 week
The hardware can generate its own frames (eg RTS/CTS exchanges, other
kinds of 802.11 management stuff, especially when it comes to 802.11n)
and these also have PWRMGT flags. So if the VAP is asleep but the
NIC is in force-awake for some reason, ensure that the self-generated
frames have PWRMGT set to 1.
Now, this (like basically everything to do with powersave) is still
racy - the only way to guarantee that it's all actually consistent
is to pause transmit and let it finish before transitioning the VAP
to sleep, but this at least gets the basic method of tracking and
updating the state debugged.
Tested:
* AR5416, STA mode
* AR9380, STA mode
to sleep permanently by executing a HLT with interrupts disabled.
When this condition is detected the guest with be suspended with a reason of
VM_SUSPEND_HALT and the bhyve(8) process will exit.
Tested by executing "halt" inside a RHEL7-beta guest.
Discussed with: grehan@
Reviewed by: jhb@, tychon@
If time_t is 64-bit (i.e. isn't 32-bit) allow any value of year, not
just years less than 2038.
Don't bother fixing the underflow in the case of years before 1903.
MFC after: 1 week
Sponsored by: DARPA, AFRL
and geom_uncompress(4). Now, they produce an almost clean diff(1) output.
Remove a duplicated variable from g_uncompress.c and an unnecessary header
from g_uzip.c.
No functional changes.
This allows existing loader.conf files that set "console=comconsole"
to work without failing. No functional difference otherwise.
Reported by: Michael Dexter, pfSense install.
Reviewed by: neel
MFC after: 3 weeks
Nobody yet reported disk supporting I/Os less then our MAXPHYS value, but
since we any way have code to read Block Limits VPD page, that is easy.
MFC after: 2 weeks
#NO_UNIVERSE. Many of these config files are important examples, but
add little to no regresive value to the intended purpose of
UNIVERSE. We now build over 120 kernels during universe. There's
really little to no value to this over building say 60 or even 30 of
them (either is still a way too big number). This is especially true
for kernels that are nothing more than including a common base and
adding a static DTB file. Start by pruning 1/3 of the arm kernels that
add little regresion value.
kernel config file. If you also want to have a static DTB compiled
into your kernel, however, it cannot be a list. We have no mechanism
in the kernel for picking one, so that doesn't make sense and will
result in a compile-time error.
The changes how TRIM requests are generated to use ZIO_TYPE_FREE + a priority
instead of ZIO_TYPE_IOCTL, until processed by vdev_geom; only then is it
translated the required geom values. This reduces the amount of changes
required for FREE requests to be supported by the new IO scheduler. This
also eliminates the need for a specific DKIOCTRIM.
Also fixed FREE vdev child IO's from running ZIO_STAGE_VDEV_IO_DONE as part
of their schedule.
As the new IO scheduler can result in a request to execute one type of IO to
actually run a different type of IO it requires that zio_trim requests are
processed without holding the trim map lock (tm->tm_lock), as the free request
execute call may result in write request running hence triggering a
trim_map_write_start call, which takes the trim map lock and hence would result
in recused on no-recursive sx lock.
This is based off avg's original work, so credit to him.
MFC after: 1 month
Instead of rereading VPD pages on every device open, do it only on initial
device probe, and in cases when device reported via UNIT ATTENTIONs that
something has changed. Capacity is still rereaded on every open because
it is more critical for operation and more probable to change in run time.
On my tests with Intel 530 SSDs on mps(4) HBA this change reduces time
GEOM needs to retaste the device (that includes few open/close cycles)
from ~150ms to ~30ms.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
fixes and beacon programming / debugging into the ath(4) driver.
The basic power save tracking:
* Add some new code to track the current desired powersave state; and
* Add some reference count tracking so we know when the NIC is awake; then
* Add code in all the points where we're about to touch the hardware and
push it to force-wake.
Then, how things are moved into power save:
* Only move into network-sleep during a RUN->SLEEP transition;
* Force wake the hardware up everywhere that we're about to touch
the hardware.
The net80211 stack takes care of doing RUN<->SLEEP<->(other) state
transitions so we don't have to do it in the driver.
Next, when to wake things up:
* In short - everywhere we touch the hardware.
* The hardware will take care of staying awake if things are queued
in the transmit queue(s); it'll then transit down to sleep if
there's nothing left. This way we don't have to track the
software / hardware transmit queue(s) and keep the hardware
awake for those.
Then, some transmit path fixes that aren't related but useful:
* Force EAPOL frames to go out at the lowest rate. This improves
reliability during the encryption handshake after 802.11
negotiation.
Next, some reset path fixes!
* Fix the overlap between reset and transmit pause so we don't
transmit frames during a reset.
* Some noisy environments will end up taking a lot longer to reset
than normal, so extend the reset period and drop the raise the
reset interval to be more realistic and give the hardware some
time to finish calibration.
* Skip calibration during the reset path. Tsk!
Then, beacon fixes in station mode!
* Add a _lot_ more debugging in the station beacon reset path.
This is all quite fluid right now.
* Modify the STA beacon programming code to try and take
the TU gap between desired TSF and the target TU into
account. (Lifted from QCA.)
Tested:
* AR5210
* AR5211
* AR5212
* AR5413
* AR5416
* AR9280
* AR9285
TODO:
* More AP, IBSS, mesh, TDMA testing
* Thorough AR9380 and later testing!
* AR9160 and AR9287 testing
Obtained from: QCA
Some code will appear soon that is actually setting the chip powerstate
separate from the self-generated frames power state.
* Allow the AR5416 family chips to actually have the power state changed
from the self generated state change.
Tested (STA mode):
* AR5210
* AR5211
* AR5412
* AR5413
* AR5416
* AR9285
All rtsock-initiated rte creation/modification are now
performed in route.c holding radix tree write lock.
This reduces the need for per-rte mutex.
Sponsored by: Yandex LLC
MFC after: 1 month
the 'HLT' instruction. This condition was detected by 'vm_handle_hlt()' and
converted into the SPINDOWN_CPU exitcode . The bhyve(8) process would exit
the vcpu thread in response to a SPINDOWN_CPU and when the last vcpu was
spun down it would reset the virtual machine via vm_suspend(VM_SUSPEND_RESET).
This functionality was broken in r263780 in a way that made it impossible
to kill the bhyve(8) process because it would loop forever in
vm_handle_suspend().
Unbreak this by removing the code to spindown vcpus. Thus a 'halt' from
a Linux guest will appear to be hung but this is consistent with the
behavior on bare metal. The guest can be rebooted by using the bhyvectl
options '--force-reset' or '--force-poweroff'.
Reviewed by: grehan@
into the area backed by vm_page_array wrongly compared end with
vm_page_array_size. It should be adjusted by first_page index to be
correct.
Also, the corner and incorrect case of the requested range extending
after the end of the vm_page_array was incorrectly handled by
allocating the segment.
Fix the comparision for the end of range and return EINVAL if the end
extends beyond vm_page_array.
Discussed with: royger
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
pmap pvlist locks which are scaled by MAXCPU.
This allows an amd64 system to boot with MAXCPU set
to 256, which is currently FreeBSD's hard limit without
x2apic support.
Compile-tested for other arch's.
PR: 185831
Discussed with: jhb
MFC after: 3 weeks
exists on another interface. The panic was introduced by change 264887, which
changed the fibnum parameter in the call to rtalloc1_fib() in
ifa_switch_loopback_route() from RT_DEFAULT_FIB to RT_ALL_FIBS. The solution
is to use the interface fib in that call. For the majority of users, that will
be equivalent to the legacy behavior.
PR: kern/189089
Reported by: neel
Reviewed by: neel
MFC after: 3 weeks
X-MFC with: 264887
Sponsored by: Spectra Logic
platforms which do not use loaders or kernels that want to hardcode
options or for FDT passed in by loader.
Also fix a build issue by putting the kmdp variable accessed back under
the #ifdef FDT; we may wish to revisit decision in which case more
code needs changing.
Submitted by: brooks
by adding an argument to the VM_SUSPEND ioctl that specifies how the virtual
machine should be suspended, viz. VM_SUSPEND_RESET or VM_SUSPEND_POWEROFF.
The disposition of VM_SUSPEND is also made available to the exit handler
via the 'u.suspended' member of 'struct vm_exit'.
This capability is exposed via the '--force-reset' and '--force-poweroff'
arguments to /usr/sbin/bhyvectl.
Discussed with: grehan@
old devd's and thus hosts that get IP addresses from DHCP was too much
of a POLA violation.
The sysctl may be removed again after r263758 has been merged to at
least stable/9 and stable/10, and releases have been cut from those
branches.
Discussed with: mjg
Reported by: theraven, rwatson
It exposes I/O resources to user space, so that programs can peek
and poke at the hardware. It does not itself have knowledge about
the hardware device it attaches to.
Sponsored by: Juniper Networks, Inc.
Instead opening/closing provider by each of metadata classes, do it only
once in core code. Since for SCSI disks open/close means sending some
SCSI commands to the device, this change reduces taste time.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
FD_SETSIZE is often used as an argument to select or compared with an
integer file descriptor. Rather than force 3rd party software to add
explicit casts, just make it a plain (int) constant as on other
operating systems.
Previous discussion:
http://lists.freebsd.org/pipermail/freebsd-standards/2012-July/002410.html
returns ZIO_PIPELINE_CONTINUE from vdev_op_io_start to zio_execute resulting
in the wrong ZIO continuing its pipeline.
This is a serious issue which could cause data loss / corruption but appears
to be limited to error handling such as when vdev_readable(vd) returns false.
MFC after: 2 days
the MYBEACON RX filter (only receive beacons which match the BSSID)
or all beacons on the current channel.
* Add the relevant RX filter entry for MYBEACON.
Tested:
* AR5416, STA
* AR9285, STA
TODO:
* once the code is in -HEAD, just make sure that the code which uses it
correctly sets BEACON for pre-AR5416 chips.
Obtained from: QCA, Linux ath9k
the QCA HAL.
This fires off an interrupt if the TSF from the AP / IBSS peer is
wildly out of range. I'll add some code to the ath(4) driver soon
which makes use of this.
TODO:
* verify this didn't break TDMA!
to the hardware.
The QCA HAL has a comment noting that if this isn't done, modifications
to AR_IMR_S2 before AR_IMR is flushed may produce spurious interrupts.
Obtained from: QCA
Flushing the caches is required before doing a panic dump, but ARM
doesn't provide a flavor of flush that gets broadcast to other cores.
However, all cores except one are stopped before doing a dump, so this
works around the lack of a global flush/invalidate by doing it locally
on each CPU as part of stopping.
Discussed with: cognet@
This was added ca. 2004 for the purpose of ensuring the caches were in the
right state after the debugger set a breakpoint. kdb_cpu_sync_icache()
was added in 2007 to handle that situation, and now the wbinv_all is
actually harmful because the operation isn't broadcast to other cores.
* memory is now allocated as early as possible, without holding locks.
* sysctl users are now guaranteed to get a response (M_WAITOK buffer prealloc).
* socket users are more likely to use on-stack buffer for replies.
* standard kernel malloc/free functions are now used instead of radix wrappers.
rt_msg2() has been renamed to rtsock_msg_buffer().
MFC after: 1 month
#gpio-cells property.
Add a new ofw_bus method (OFW_BUS_MAP_GPIOS()) that allows the GPIO
controller to implement its own mapping to deal with gpio-specifiers,
allowing the decoding of gpio-specifiers to be controller specific.
The default ofw_bus_map_gpios() decodes the linux standard (#gpio-cells =
<2>) and the FreeBSD standard (#gpio-cells = <3>).
It pass the gpio-specifier flag field to the children as an ivar variable so
they can act upon.
checks for special pcid values in invlpg_pcid_handler(). Forst check
for special values, and only then do PCID-specific page invalidation.
Minor fix to the style compliance, declare local variable at the
function start.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
entry and performs the upgrade of the entry permissions from read-only
to read-write, we must allow to search for the source pages in the
backing object, like we do in the case of forking the read-only wired
entry. For the fork case, the behaviour is allowed by src_readonly
boolean, which in fact is only used to assert that read-write case
provides all source pages in the top-level object.
Eliminate the src_readonly variable. Allow for the copy loop to look
into the backing objects, add explicit asserts to ensure that only
read-only and upgrade case actually does.
Expand comments. Change the panic call into assert.
Reported by: markj
Tested by: markj, pho (previous version)
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
kernel will now boot on both BIOS and EFI systems without modification.
Equivalent functionality in GENERIC requires making vt(9) the default console
driver, which is probably appropriate at this point.
using armv7_idcache_wbinv_all, because wbinv_all doesn't broadcast the
operation to other cores. In elf_cpu_load_file() use icache_sync_all()
and explain why it's needed (and why other sync operations aren't).
As part of doing this, all callers of cpu_icache_sync_all() were
inspected to ensure they weren't relying on the old side effect of
doing a wbinv_all along with the icache work.
RTM_CHANGE is now handled inside route.c:rtrequest1_fib() as it should be.
Note change change handler is a separate function rtrequest1_fib_change().
MFC after: 1 month
the cpufreq code. Replace its use with smp_started. There's at least
one userland tool that still looks at the kern.smp.active sysctl, so
preserve it but point it to smp_started as well.
Discussed with: peter, jhb
MFC after: 3 days
Obtained from: Netflix
define a few imx_ccm_foo() functions that are implemented by the imx51 or
imx6 ccm code. Of course, the imx6 ccm code is still more a wish than
reality, so for now its implementations just return hard-coded numbers.
copy of the code from boot1.chrp again.
The resulting image is installed to /boot/boot1.efifat. If dd'ed to an 800K
"efi" partition, it should result in a bootable system.
replace the vt_vga driver with vt_efifb.
This is intended to help with snapshot builds only.
There is no intention to MFC this commit.
Sponsored by: The FreeBSD Foundation
a jtag debugging product, which was used on early Beaglebone boards (later
boards used a standard FTDI 2232C product ID). Change the name accordingly,
and also add an entry for XDS100V3, the latest version of that product
which has its own new product ID number.
Device type and revision is now determined from the bcdDevice field and
doesn't need to be in the table at all. The feature that skips creation
of /dev/ttyU* entries for jtag and gpio interfaces is enhanced:
- The feature is now optional, but enabled by default. A tunable and
sysctl are available to control it: hw.usb.uftdi.skip_jtag_interfaces.
- We no longer assume interface #0 is the only jtag interface. Up to
eight interfaces per chip can be flagged as jtag. (Current ftdi chips
support a max of 4 interfaces; this leaves room for growth.)
- Some manufacturers don't change the product ID or use the same ID for
different devices intended for both serial-comms and jtag/gpio use.
Often while the product ID is the same, the product name string is
different, so it's now possible to search for the product name in a
table of strings and get the set of non-tty interfaces from that table.
- DIOCADDADDR adds addresses and puts them into V_pf_pabuf
- DIOCADDRULE takes all addresses from V_pf_pabuf and links
them into rule.
The ugly part is that if address is a table, then it is initialized
in DIOCADDRULE, because we need ruleset, and DIOCADDADDR doesn't
supply ruleset. But if address is a dynaddr, we need address family,
and address family could be different for different addresses in one
rule, so dynaddr is initialized in DIOCADDADDR.
This leads to the entangled state of addresses on V_pf_pabuf. Some are
initialized, and some not. That's why running pf_empty_pool(&V_pf_pabuf)
can lead to a panic on a NULL table address.
Since proper fix requires API/ABI change, for now simply plug the panic
in pf_empty_pool().
Reported by: danger
request during SLEEP results in a hang.
Whilst I'm here, add in some disabled code that will transition to RUN
if there's multicast traffic. It's not needed for Atheros hardware but
it may be for other hardware.
Tested:
* AR5416, STA mode (powersave)
* AR5212, STA mode (powersave)
These two bugs are closely related. The root cause is that ifa_ifwithnet
does not consider FIBs when searching for an interface address.
sys/net/if_var.h
sys/net/if.c
Add a fib argument to ifa_ifwithnet and ifa_ifwithdstadddr. Those
functions will only return an address whose interface fib equals the
argument.
sys/net/route.c
Update calls to ifa_ifwithnet and ifa_ifwithdstaddr with fib
arguments.
sys/netinet/in.c
Update in_addprefix to consider the interface fib when adding
prefixes. This will prevent it from not adding a subnet route when
one already exists on a different fib.
sys/net/rtsock.c
sys/netinet/in_pcb.c
sys/netinet/ip_output.c
sys/netinet/ip_options.c
sys/netinet6/nd6.c
Add RT_DEFAULT_FIB arguments to ifa_ifwithdstaddr and ifa_ifwithnet.
In some cases it there wasn't a clear specific fib number to use.
In others, I was unable to test those functions so I chose
RT_DEFAULT_FIB to minimize divergence from current behavior. I will
fix some of the latter changes along with PR kern/187553.
tests/sys/netinet/fibs_test.sh
tests/sys/netinet/udp_dontroute.c
tests/sys/netinet/Makefile
Revert r263738. The udp_dontroute test was right all along.
However, bugs kern/187550 and kern/187553 cancelled each other out
when it came to this test. Because of kern/187553, ifa_ifwithnet
searched the default fib instead of the requested one, but because
of kern/187550, there was an applicable subnet route on the default
fib. The new test added in r263738 doesn't work right, however. I
can verify with dtrace that ifa_ifwithnet returned the wrong address
before I applied this commit, but route(8) miraculously found the
correct interface to use anyway. I don't know how.
Clear expected failure messages for kern/187550 and kern/187552.
PR: kern/187550
PR: kern/187552
Reviewed by: melifaro
MFC after: 3 weeks
Sponsored by: Spectra Logic
SLEEP rather than RUN.
Without this things like 'ifconfig wlan0 list sta' don't work when the
NIC is power save.
Tested:
* AR5212, STA mode (with powersave)
* AR5416, STA mode (with powersave)
commit 003649d9622ce252a2794ae5891ee7e7c209caca
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Wed Feb 5 18:32:09 2014 +0000
Teach the FreeBSD/beri boot to "auto-detect" whether argument 4 (a3) is a
memory size of pointer to a struct bootinfo * by looking at its value and
seeing whether it is pointer-like. If a pointer, assume it's a bootinfo
and extract memsize from it instead; otherwise, use it as memsize directly.
This allows kernels to support bootinfo being passed by loader (and boot2)
while still supporting older Miniboot setups.
commit f7045af9a1e92b6bd92541fe5d25abf66d824e8f
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Thu Feb 6 13:45:34 2014 +0000
When the module metadata pointer is available from loader, use it in the
kernel.
commit 52e0e1ff2cba9dfcfab9e1d0a31fb7fdf7317450
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Thu Feb 6 19:57:48 2014 +0000
In the BERI kernel boot code, extract 'boothowto' (which includes boot flags
such as '-s') and 'envp' from passed module data. Booting to single-user
mode using boot flags now works.
Sponsored by: DARPA, AFRL
for the VOP_READ() call. This patch fixes both the old and new
server for this case.
PR: 185232
Submitted by: PR had patch for old server
Reviewed by: kib
MFC after: 2 weeks
sys/net/route.c
In rtinit1, use the interface fib instead of the process fib. The
latter wasn't very useful because ifconfig(8) is usually invoked
with the default process fib. Changing ifconfig(8) to use setfib(2)
would be redundant, because it already sets the interface fib.
tests/sys/netinet/fibs_test.sh
Clear the expected ATF failure
sys/net/if.c
Pass the interface fib in calls to rtrequest1_fib and rtalloc1_fib
sys/netinet/in.c
sys/net/if_var.h
Add a fibnum argument to ifa_switch_loopback_route, a subroutine of
in_scrubprefix. Pass it the interface fib.
PR: kern/187549
Reviewed by: melifaro
MFC after: 3 weeks
Sponsored by: Spectra Logic Corporation
Instead of allocating up to 16MB or RAM at once to handle whole I/O,
allocate up to 1MB at a time, but do multiple ctl_datamove() and storage
I/Os if needed.
Some of the code in xen-locore.S was picked from Cherry G. Mathew
amd64 Xen PV branch, but I've failed to set the proper copyright, so
do it now.
Approved by: gibbs
This transitions the VAP in and out of SLEEP state based on:
* whether there's been an active transmission in the last (hardcoded) 500ms;
* whether the TIM from the AP indicates there is data available.
It uses the beacon reception to trigger the active traffic check.
This way there's no further timer running to wake up the CPU
from its own sleep states.
Right now the VAP isn't woken up for multicast traffic - mostly because
the only NIC I plan on doing this for right will auto wakeup and stay
awake for multicast traffic indicated in the TIM. So I don't have
to manually keep the hardware awake.
This doesn't do anything if the NIC doesn't advertise it implements
the new SWSLEEP capability AND if the VAP doesn't have powersave
enabled.
It also doesn't do much with ath(4) as it doesn't currently implement
the SLEEP state.
Tested:
* AR5416, STA mode (with local ath(4) changes)
This simplifies the code and should avoid the clang sparc
port from generating an abort() call.
Requested by: rdivacky
Submitted by: jhb
MFC after: 2 weeks
Frames transmitted during SLEEP state should be queued in the
power save queue before waking the unit up. Otherwise DHCP
requests and such will be dropped if the NIC is asleep - the
NIC will wake up but not transmit the frame.
- Add a comment about FTDI and ZLPs.
- Correctly check odditiy of baud rate divisor.
- Correct IOCTL handling for "error" and "event" char.
MFC after: 1 weeks
concurrent updates from any completing transmits in other threads.
This was exposed when doing power save work - net80211 is constantly
doing reassociations and it's causing the rate control state to get
blanked out. This could cause the rate control code to assert.
This should be MFCed to stable/10 as it's a stability fix.
Tested:
* AR5416, STA
MFC after: 7 days
The MAC filter set may be called without softc_lock held in the case of
SIOCADDMULTI and SIOCDELMULTI ioctls. The ioctl handler checks IFF_DRV_RUNNING
flag which implies port started, but it is not guaranteed to remain.
softc_lock shared lock can't be held in the case of these ioctls processing,
since it results in failure where kernel complains that non-sleepable
lock is held in sleeping thread.
Both problems are repeatable on LAG with LACP proto bring up.
Submitted by: Andrew Rybchenko <Andrew.Rybchenko at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 weeks
Make sure not to start I/O bigger than MAXPHYS bytes.
Quoting r264504:
When we detect the condition, we'll reduce the block count and perform
a "short" read. In g_uncompress_done() we need to consider the original
I/O length and stop early if we're about to deflate a block that we didn't
read. By using bio_completed in the cloned BIO and not bio_length to
check for this, we automatically and gracefully handle short reads that
our providers may be doing on top of the short reads we may initiate
ourselves.
Reviewed by: marcel
The existing cleanup code was based on the Atheros reference driver
from way back and stuff that was in Linux ath9k. It turned out to be ..
rather silly.
Specifically:
* The whole method of determining whether there's hardware-queued frames
was fragile and the BAW would never quite work right afterwards.
* The cleanup path wouldn't correctly pull apart aggregate frames in the
queue, so frames would not be freed and the BAW wouldn't be correctly
updated.
So to implement this:
* Pull the aggregate frames apart correctly and handle each separately;
* Make the atid->incomp counter just track the number of hardware queued
frames rather than try to figure it out from the BAW;
* Modify the aggregate completion path to handle it as a single frame
(atid->incomp tracks the one frame now, not the subframes) and
remove the frames from the BAW before completing them as normal frames;
* Make sure bf->bf_next is NULled out correctly;
* Make both aggregate session and non-aggregate path frames now be
handled via the incompletion path.
TODO:
* kill atid->incomp; the driver tracks the hardware queued frames
for each TID and so we can just use that.
This is a stability fix that should be merged back to stable/10.
Tested:
* AR5416, STA
MFC after: 7 days
MAC
* Now that the paused < 0 bugs have been identified, make the DPRINTF()
a device_printf() again. Anything else that shows up here needs to be
fixed immediately.
Tested:
* AR5416, STA mode
MFC after: 7 days
During power save testing I noticed that the cleanup code is being
called during a RUN->RUN state transition. It's because the net80211
stack is treating that (for reasons I don't quitey know yet) as a
reassociation and this calls the node cleanup code. The reason it's
seeing a RUN->RUN transition is because during active power save
stuff it's possible that the RUN->SLEEP and SLEEP->RUN transitions
happen so quickly that the deferred net80211 vap state code
"loses" a transition, namely the intermediary SLEEP transition.
So, this was causing the node reassociation code to sometimes be called
twice in quick succession and this would result in ath_tx_tid_cleanup()
to be called again. The code calling it would always call pause, and
then only call resume if the TID didn't have "cleanup_inprogress" set.
Unfortunately it didn't check if it was already set on entry, so it
would pause but not call resume. Thus, paused would be called more
than once (once before each entry into ath-tx_tid_cleanup()) but resume
would only be called once when the cleanup state was finished.
This doesn't entirely fix all of the issues seen in the cleanup path
but it's a necessary first step.
Since this is a stability fix, it should be merged to stable/10 at some
point.
Tested:
* AR5416, STA mode
MFC after: 7 days
post-create/mkdir directory attributes. This allows the RPC to
name cache the newly created directory and reduces the lookup RPC
count for applications creating a lot of directories.
MFC after: 2 weeks
- These were needed on armv4/5 (VIVT cache), not needed on armv6.
- The wbinv_all call can't be used on SMP systems; cache operations by
set/way are not broadcast to other cores.
- The TLB maintenance operations needed for pmap_growkernel() happen in
pmap_grow_l2_bucket(), so there's no need to flush all TLB entries at
the end.
- There may not be any need for the TLB flush at the beginning of
pmap_release(), but it's left in for now pending more investigation.
Pointed out by: Svatopluk Kraus <onwahe@gmail.com>
Discussed with: cognet@
De-virtualize UMA zone pf_mtag_z and move to global initialization part.
The m_tag struct does not know about vnet context and the pf_mtag_free()
callback is called unaware of current vnet. This causes a panic.
MFC after: 1 week
Since <sys/capsicum.h> does not comply to any standards, standards-compliant
applications do not include it and it is not useful to restrict what is
exposed depending on the requested standard.
In addition, the use of types like u_int makes the header fail in strict
standards compliance modes anyway.
post-open/create directory attributes. This allows the RPC to
name cache the newly created file and reduces the lookup RPC
count by about 10% for software builds.
MFC after: 2 weeks
attributes. This allows the client to cache directory names
when they are looked up, reducing the Lookup RPC count by
about 40% for software builds.
MFC after: 2 weeks
