ports. This currently is a nop, but will soon be used to allow
support for multiple boards to be built into one kernel (starting with
AT91RM9200 and expanding out from there).
- Align the RX buffers on the cache line size, otherwise the requirement
of partial cache line flushes on every are pretty much guaranteed. [1]
- Make the code setting the RX timeout match its comment (apparently,
start and stop bits were missed in the previous calculation). [1]
- Cover the busdma operations in at91_usart_bus_{ipend,transmit}() with
the hardware mutex, too, so these don't race against each other.
- In at91_usart_bus_ipend(), reduce duplication in the code dealing with
TX interrupts.
- In at91_usart_bus_ipend(), turn the code dealing with RX interrupts
into an else-if cascade in order reduce its complexity and to improve
its run-time behavior.
- In at91_usart_bus_ipend(), add missing BUS_DMASYNC_PREREAD calls on
the RX buffer map before handing things over to the hardware again. [1]
- In at91_usart_bus_getsig(), used a variable of sufficient width for
storing the contents of USART_CSR.
- Use KOBJMETHOD_END.
- Remove an unused header.
Submitted by: Ian Lepore [1]
Reviewed by: Ian Lepore
MFC after: 1 week
as otherwise the interrupt handling code may modify data in the non-DMA
part of the cache line while we have it stashed away in the temporary
stack buffer, then we end up restoring a stale value.
PR: 160431
Submitted by: Ian Lepore
MFC after: 1 week
used in the code which needs to implement some specific
behaviour when being run under QEMU.
- Make PXA UART probe code to work under QEMU gumstix, which
doesn't emulate all the ports properly.
New kernel events can be added at various location for sampling or counting.
This will for example allow easy system profiling whatever the processor is
with known tools like pmcstat(8).
Simultaneous usage of software PMC and hardware PMC is possible, for example
looking at the lock acquire failure, page fault while sampling on
instructions.
Sponsored by: NETASQ
MFC after: 1 month
As of FreeBSD 8, this driver should not be used. Applications that use
posix_openpt(2) and openpty(3) use the pts(4) that is built into the
kernel unconditionally. If it turns out high profile depend on the
pty(4) module anyway, I'd rather get those fixed. So please report any
issues to me.
The pty(4) module is still available as a kernel module of course, so a
simple `kldload pty' can be used to run old-style pseudo-terminals.
platforms.
This will make every attempt to mount a non-mpsafe filesystem to the
kernel forbidden, unless it is expressely compiled with
VFS_ALLOW_NONMPSAFE option.
This patch is part of the effort of killing non-MPSAFE filesystems
from the tree.
No MFC is expected for this patch.
long for specifying a boundary constraint.
- Change bus_dma tags to use bus_addr_t instead of bus_size_t for boundary
constraints.
These allow boundary constraints to be fully expressed for cases where
sizeof(bus_addr_t) != sizeof(bus_size_t). Specifically, it allows a
driver to properly specify a 4GB boundary in a PAE kernel.
Note that this cannot be safely MFC'd without a lot of compat shims due
to KBI changes, so I do not intend to merge it.
Reviewed by: scottl
dynamic rounding modes, but FPUless chips that use softfloat can support it
because everything is emulated anyway. (We presently have incomplete
support for hardware FPUs.)
Submitted by: Ian Lepore
- Write Buffers have to be drained after write to Page Table even if caches
are in write-through mode.
- Make sure to sync PTE in pmap_zero_page_generic().
Submitted by: Michal Mazur
Reviewed by: cognet
Obtained from: Semihalf
MFC after: 1 month
sintrnames and sintrcnt are initialized with non-zero values, which were
discarded by the .bss directive, so consumers like "vmstat -i" were not
getting correct data.
Submitted by: Lukasz Plachno
Obtained from: Semihalf
MFC after: 1 month
This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.
This patch also fixes some build issues in avr32dci.c
MFC after: 2 weeks
According to the open firmware standard, finddevice call has to return
a phandle with value of -1 in case of error.
This commit is to:
- Fix the FDT implementation of this interface (ofw_fdt_finddevice) to
return (phandle_t)-1 in case of error, instead of 0 as it does now.
- Fix up the callers of OF_finddevice() to compare the return value with
-1 instead of 0 to check for errors.
- Since phandle_t is unsigned, the return value of OF_finddevice should
be checked with '== -1' rather than '<= 0' or '> 0', fix up these cases
as well.
Reported by: nwhitehorn
Reviewed by: raj
Approved by: raj, nwhitehorn
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
to kern/subr_bus.c. Simplify this function so that it no longer
depends on malloc() to execute. Identify a few other places where
it makes sense to use device_delete_all_children().
MFC after: 1 week
all the architectures.
The option allows to mount non-MPSAFE filesystem. Without it, the
kernel will refuse to mount a non-MPSAFE filesytem.
This patch is part of the effort of killing non-MPSAFE filesystems
from the tree.
No MFC is expected for this patch.
Tested by: gianni
Reviewed by: kib
