which is now disabled by default. The detection is known to cause hangs
on boot with some new Lenovo laptops on FreeBSD/amd64.
Reported by: gnn
Discussed with: jkim
MFC after: 3 months
not true on old PCI based controllers. DAC configuration is read
from EEPROM in device reset phase and driver can override DAC
configuration. However I guess there is an undocumented reason why
EEPROM configuration does not enable DAC so do not blindly override
DAC configuration. Recent PCIe based controllers are supposed to
support 64bit DMA so allow 64bit DMA only on PCIe based controllers.
PR: kern/157184
MFC after: 1 week
IFF_DRV_RUNNING flag. Previously running dhclient or adding alias
addresses reinitialized controller and it resulted in unnecessary
link flips.
Reviewed by: marius
Oxford Semiconductor OX16PCI954 but uses only two ports with a non-default
clock rate.
PR: kern/152034
Tested by: Hans Fiedler hans of hermes louisville edu
MFC after: 1 week
This brings USB bus more in line with how newbus is supposed to be used.
Also, because of the two-pass probing the following message was produced
by devd in default configuration when almost any USB device was
connected:
Unknown USB device: vendor <> product <> bus <>
This should be fixed now.
Note that many USB device drivers pass some information from probe
method to attach method via ivars. For this to continue working we rely
on the fact that the subr_bus code calls probe method of a winning driver
again before calling its attach method in the case where multiple
drivers claim to support a device. This is done because device
description is set in successful probe methods and we want to get a correct
device description from a winning driver. So now this logic is re-used
for setting ivars too.
Reviewed by: hselasky
MFC after: 1 month
When supported by hardware, this allows to control per-port activity, locate
and fault LEDs via the led(4) API for localization and status reporting
purposes. Supporting AHCI controllers may transmit that information to the
backplane controllers via SGPIO interface. Backplane controllers interpret
received statuses in some way (IBPI standard) to report them using present
indicators.
the multicast key search support for AR5212, AR5416 and later.
The general HAL routine ath_hal_getcapability() implement checking this
but it's overridden by a check in ar5212_misc:ar5212GetCapability().
This restores the later functionality in case it's found to be broken
in any of the 11n chipsets.
The other queues, especially the command queue, uses the FIFO mode
which doesn't require the byte count table because queued entries are
processed in order.
Pointed out by: Lucius Windschuh <lwindschuh at googlemail dot com>
Since the returned NF will be -ve, checking for <= 0 is not good
enough. For now, check whether it equals 0 or -1; a future commit
will tidy this mess up and have it return HAL_BOOL instead.
The eeprom Get method should return HAL_OK if fastclock is enabled in the
EEPROM. It was returning the opposite of what it should have.
Submitted by: Matthew Fleming <mdf356@gmail.com>
The code assumed it could return HAL_OK, HAL_EINVAL and other
HAL_STATUS types; so it shouldn't be declared as returning HAL_BOOL.
This commit was brought to you by the Clang compiler.
Submitted by: Matthew Fleming <mdf356@gmail.com>
I've tested this locally and it does indeed read and attach to an AR9287
EEPROM. But a lot more code needs to be ported over to the HAL before
the AR9287 is functional.
I'm importing this separate from the rest of the codebase (and unlinked from
the build for now) in case someone wishes to begin fiddling with porting
the rest of the code over from Linux ath9k.
Obtained from: Linux ath9k
is totally disabled.
The Atheros HAL code does this for Sowl/Howl but not for Owl (AR5416) where
RIFS is disabled by default.
This seems to quieten the occasional baseband hang I've been seeing with
the AR9160 in STA mode under constant heavy traffic load.
Obtained from: Atheros
Some files keep the SUN4V tags as a code reference, for the future,
if any rewamped sun4v support wants to be added again.
Reviewed by: marius
Tested by: sbruno
Approved by: re
architectures (i386, for example) the virtual memory space may be
constrained enough that 2MB is a large chunk. Use 64K for arches
other than amd64 and ia64, with special handling for sparc64 due to
differing hardware.
Also commit the comment changes to kmem_init_zero_region() that I
missed due to not saving the file. (Darn the unfamiliar development
environment).
Arch maintainers, please feel free to adjust ZERO_REGION_SIZE as you
see fit.
Requested by: alc
MFC after: 1 week
MFC with: r221853
that for _ptr operations, when not used directly with uintptr_t, we
needed to manually cast.
Use the cast on the _ptr version, where it actually wasn't (please note
that i386 doesn't get it right, while amd64 doesn't seem to compile
cfi neither in LINT, that is why it doesn't fail).
Reported by: sbruno
for the AR9280 based NICs if it's actually enabled.
Some of the OLC code was erroneously called during setup
and calibration. This may have caused some incorrect behaviour.
table which contains the per-rate target TX power.
This code is shared between the v14 eeprom board setup (AR5416, AR9160,
AR9280) and will also be used by the upcoming Kite (AR9287) support.
* grab the main, alt and selected LNA config
* add some optional / disabled logging code
* add a check to reject packets with an invalid main rssi too,
in case the alt is the active receive chain and main is -ve.
Note: The software-controlled combined diversity code is still disabled.
- Use bus_bind_intr() to bind interrupt to a CPU when RSS/TSS is used.
- Use M_DONTWAIT for RSS/TSS buffer allocation.
- Add statistic to track max DRBR queue depth.
- Fix problem in bxe_change_mtu() which referenced the old MTU size
in a debug print statement.
MFC after: Two weeks
disabled for BCM5719 A0 revision due to known hardware errata.
Many thanks to Broadcom for continuing support of FreeBSD.
Submitted by: Geans Pin at Broadcom
AR8132 FastEthernet controller. The PHY has no ability to
establish a gigabit link. Previously only link parters which
support down-shifting was able to establish link.
This change should fix a long standing link establishment issue of
AR8132.
PR: kern/156935
MFC after: 1 week
Casting a pointer to a wide integer is probably not that bad, but I am
still guilty of not testing this.
Pointyhat to: avg
MFC after: 1 week
X-MFC with: r221803
This brings our implementation in line with OSS specification for
systems that support mmap. The change should also improve compatibility
with OSS software not specifically written for FreeBSD, e.g. PulseAudio
OSS plugin.
Reviewed by: kib, jhb
MFC after: 1 week
environments.
In setups where NF calibration can take a while, don't load the CCA
and kick off a new NF calibration if the previous one hasn't yet
completed. This shouldn't happen unless the environment is noisy but
those exist (hi phk!).
Here, if the previous NF hasn't completed when ar5416LoadNf() is run
(which reads the NF), it skips updating the history buffer, loading
the NF CCA array and kicking off the next NF cal. It's hoped it'll
occur in the next long calibration interval.
Obtained from: Atheros, ath9k, my local HAL
This is taking quite a while for some people in some situations
(eg AR5418 in phk's Abusive Radio Environment).
Instead, the rest of the calibration related code should
ensure that a NF calibration has occured before reading NF
values and kicking off another NF calibration.
The channel should also likely be marked as "noisy" (CWINT)
if the NF calibration takes too long.
* Correct some of the silicon revision checks to match what
the Atheros HAL does. (See [1] below.)
* Move the PA cal and init cal method assignment to -after-
the mac version/revision IDs are stored. The AR9285 init
cal was never being called.
* Enable ANI.
Note Kite 1.0 and 1.1 were prototypes that shouldn't be seen
in the wild. Linux ath9k simply removed the prototype code from
their codebase. I'm going to leave it in there for now but
make it conditionally compilable in the future.
Obtained from: Atheros
newer controllers. However, all data sheet I have access has no
indication that buffer manager should not be touched on these
controllers. It seems the buffer manager always runs on BCM5705 or
newer controllers. Some controller(e.g. BCM5719) needs other buffer
manager configuration so driver should enable buffer manager for
all controllers. Both Linux and OpenBSD/NetBSD use the same
approach.
This change polls enable bit of block to know whether specified
block was really stopped as well as enabling buffer manager for all
controllers in driver initialization.
Obtained from: NetBSD
from Atheros as to what/when this is supposed to be enabled.
Using the default RX fast diversity settings seems to help quite
a bit.
Whilst I'm here, change the prototype to return HAL_BOOL rather than int.
For now, the diversity settings are controlled by 'txantenna',
-not- rxantenna. This is because the earlier chipsets had
controllable TX diversity; the RX antenna setting twiddles
the default antenna register. I'll try sort that stuff out at
some point.
Call the antenna switch function from the board setup function
so scans, channel changes, mode changes, etc don't set the
diversity back to a default state too far from what's intended.
Things to todo:
* Squirrel away the last antenna diversity/combining parameters
and restore them during board setup if HAL_ANT_VARIABLE is
defined. That way scans, etc don't reset the diversity settings.
* Add some more public facing statistics, rather than what's
simply logged under HAL_DEBUG_DIVERSITY.
For now, the fixed antenna settings behave better than variable
settings for me. I have some further fiddling to do..
Obtained from: Atheros
The macro which I incorrectly copied into ah_internal.h assumed
that it'd be called with an AR_SREV_MERLIN_20() check to ensure
it was only enabled for Merlin (AR9280) silicon revision 2.0 or
later.
Trouble is, the 5GHz fast clock EEPROM flag is only valid for
EEPROM revision 16 or greater; it's assumed to be enabled
by default for Merlin rev >= 2.0. This meant it'd be incorrectly
set for AR5416 and AR9160 in 5GHz mode.
This would have affected non-default clock timings such as SIFS,
ACK and slot time. The incorrect slot time was very likely wrong
for 5ghz mode.
* Modify AR_SREV_MERLIN_20() to match the Atheros/Linux ath9k behaviour -
its supposed to match Merlin 2.0 and later Merlin chips.
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 2.0 and later chips
(AR9285, AR9287, etc.)
- instead of calling iwn_plcp_signal() for every frame, map the expected
value directly within wn->ridx
- concat plcp, rflags and xrflags, there is no clean byte boundary within
the flags, for example the antenna setting uses bit 6, 7 and 8
- there is still need for a custom rate to plcp mapping, as those expected
by the hardware are not conform to the std
On legacy channels every once in a while the firmware throws a SYSASSERT
on line 208. On HT channels though this does always happen and I'm not
aware of any workaround currently.
for the given channel is available.
It isn't used yet; ar5416GetWirelessModes() needs to be taught
about this rather than assuming HT20/HT40 is available.
This seems to make the AR9160 behave better during heavy scanning,
where before it'd hang and require a hard reset to recover.
Obtained From: Linux ath9k, Atheros
modifying AR_DIAG_SW.
There's a hardware workaround which sets disabling some errors
early at startup and clears said bits before the PCU begins
receiving - it does this to avoid RX descriptor status errors.
It's possible these bits aren't being completely properly twiddled
in all instances; but in particular if the diag_reg HAL variable
is set it won't be setting these bits correctly. I'll review this
at some point.
* Disable multicast search on mac address and key id - the driver
doesn't use it at the moment and thus adhoc may be broken for
merlin and later.
* Change this to be for Merlin 1.0 (which from what I understand
wasn't ever publicly released) to be more correct.
Apparently all three RX chains need to be enabled before initial calibration
is done, even if only two are configured.
Reorder the alt chain swap bit to match what the Atheros HAL is doing.
Obtained From: ath9k, Atheros
* Shuffle some of the capability numbers around to match the
Atheros HAL capability IDs, just for consistency.
* Add some new capabilities to FreeBSD from the Atheros
HAL which will be be shortly used when new chipsets are added
(HAL SGI-20 support is for Kiwi/AR9287 support); for
TX aggregation (MBSSID aggregate support, WDS aggregation
support); CST/GTT support for carrier sense/TX timeout.
channel when the channel is HT/40.
The new ANI code (primarily for the AR9300/AR9400) in ath9k sets this
register but the ANI code for the previous 11n chips didn't set this.
Unlike ath9k, only set this for HT/40 channels.
Obtained From: ath9k
These describe FCC/Japan channel and DFS behaviour.
The AR9285 and later chips don't set these bits in the eeprom, the correct
behaviour is to just assume all five bits are enabled.
specific.
The Atheros HAL and FreeBSD HAL share the same capabilities up
until HAL_CAP_11D, where things begin to diverge.
I'll look at tidying these up soon.
Obtained from: Atheros
* Add Howl (ar9130) to the list of chips that have DFS/BB/MAC hangs
* Don't treat unknown BB hangs as fatal; ath9k/Atheros HAL don't
treat it as such.
* Add HAL_DEBUG_DFS to the debug fields in ath_hal/ah_debug.h
The BB hang check simply loops over an observation register checking
for a stuck state engine, but it can happen under high traffic
conditions. Ath9k and the Atheros HAL simply log a debug message and
continue.
Private to FreeBSD:
* Add HAL_DEBUG_HANG to the debug fields
* Change the hang debugging to HAL_DEBUG_HANG rather than HAL_DEBUG_DFS
like in the Atheros HAL.
Obtained from: Atheros
For now, these are equivalent macros. AR_SREV_OWL{X}_OR_LATER
will later change to exclude Howl (AR9130) in line with what
the Atheros HAL does.
This should not functionally change anything.
Obtained from: Atheros
A quick story, which is partially documented in the commit.
The silicon revision in Linux ath9k and the Atheros HAL use an
AR_SREV_REVISION mask of 0x07.
FreeBSD's HAL uses the AR5212 AR_SREV_REVISION mask of 0x0F.
Thus the OWL silicon revisions were coming through as 0xA, 0xB,
0xC, rather than 0x0, 0x1 and 0x2.
My ath9k-sourced AR_SREV_OWL_<X> macros were thus using the wrong
silicon revision values and wouldn't correctly match.
This commit does a few things:
* Change the AR_SREV_OWL_<x> macros to use the AR_SREV_REVISION_OWL_*
values, not AR_XSREV_REVISION_OWL macros;
* Disable AR_XSREV_REVISION_OWL_* values;
* Modify the IS_5416 to properly check the MAC is OWL, rather than
potentially matching on non-OWL revisions (which shouldn't happen
unless there's a silicon revision of higher than 0x9 in a later
chip..)
* Add a couple more macros from the Atheros HAL for compatibility.
The main difference now is that the Atheros HAL defines
AR_SREV_OWL_{20,22}_OR_LATER subtly differently - it fails on all HOWL
silicon. The AR_SREV_5416_*_OR_LATER macros match on the relevant OWL
version -and- all HOWL versions, along with subsequent versions.
A subsequent commit is going to migrate the uses of AR_SREV_OWL_X_OR_LATER
to AR_SREV_5416_X_OR_LATER to match what's going on in the Atheros HAL.
There's only two uses of AR_SREV_OWL_X_OR_LATER which currently don't
apply to FreeBSD but it may do in the future.
Yes, it's all confusing!
tick driving logic to xl_tick(). Now xl_tick() handles MII tick as
well as periodic updating of statistics.
This change removes a hack used in interrupt handler where it
wanted to update statistics without driving MII tick.
picking the next available one. This may explain why xl(4) sees TX
underrun error with no queued frame. I hope this addresses a long
standing xl(4) watchdog timeout issue as well.
Obtained from: OpenBSD
RX descriptor ring. Previously it returned the number of frames
that were successfully passed to upper stack which in turn means it
ignored frames that were discarded due to errors. The number of
processed frames in RX descriptor ring is used to detect whether
driver is out of sync with controller's current descriptor pointer.
Returning number of processed frames reduces unnecessary (probably
wrong) re-synchronization.
While here, remove unnecessary local variable initialization.
handler for 3C90x and 3C90xB/C respectively. This simplifies ioctl
handler as well as enhancing readability.
While I'm here don't reprogram multicast filter when driver is not
running.
this there is a rare return path that bogusly appears
to fail when it should not. Also white space correction.
Thanks to Arnaud Lacombe for noticing the problem.
cpuset_t objects.
That is going to offer the underlying support for a simple bump of
MAXCPU and then support for number of cpus > 32 (as it is today).
Right now, cpumask_t is an int, 32 bits on all our supported architecture.
cpumask_t on the other side is implemented as an array of longs, and
easilly extendible by definition.
The architectures touched by this commit are the following:
- amd64
- i386
- pc98
- arm
- ia64
- XEN
while the others are still missing.
Userland is believed to be fully converted with the changes contained
here.
Some technical notes:
- This commit may be considered an ABI nop for all the architectures
different from amd64 and ia64 (and sparc64 in the future)
- per-cpu members, which are now converted to cpuset_t, needs to be
accessed avoiding migration, because the size of cpuset_t should be
considered unknown
- size of cpuset_t objects is different from kernel and userland (this is
primirally done in order to leave some more space in userland to cope
with KBI extensions). If you need to access kernel cpuset_t from the
userland please refer to example in this patch on how to do that
correctly (kgdb may be a good source, for example).
- Support for other architectures is going to be added soon
- Only MAXCPU for amd64 is bumped now
The patch has been tested by sbruno and Nicholas Esborn on opteron
4 x 12 pack CPUs. More testing on big SMP is expected to came soon.
pluknet tested the patch with his 8-ways on both amd64 and i386.
Tested by: pluknet, sbruno, gianni, Nicholas Esborn
Reviewed by: jeff, jhb, sbruno
Quoting the ath9k commit message:
At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.
This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.
Reference: https://patchwork.kernel.org/patch/753862/
Obtained from: Linux ath9k
The checks should function as follows:
* AR_SREV_<silicon> : check macVersion matches that version id
* AR_SREV_<silicon>_<revision> : check macVersion and macRevision match
the version / revision respectively
* AR_SREV_<silicon>_<revision>_OR_LATER: check that
+ if the chip silicon version == macVersion, enforce revision >= macRevision
+ if the chip silicon version > macVersion, allow it.
For example, AR_SREV_MERLIN() only matches AR9280 (any revision),
AR_SREV_MERLIN_10() would only match AR9280 version 1.0, but
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 version >= 2.0 _AND_
any subsequent MAC (So AR9285, AR9287, etc.)
The specific fixes which may impact users:
* if there is Merlin hardware > revision 2.0, it'll now be correctly
matched by AR_SREV_MERLIN_20_OR_LATER() - the older code simply
would match on either Merlin 2.0 or a subsequent MAC (AR9285, AR9287, etc.)
* Kite version 1.1/1.2 should now correctly match. As these macros
are used in the AR9285 reset/attach path, and it's assumed that the
hardware is kite anyway, the behaviour shouldn't change. It'll only
change if these macros are used in other codepaths shared with
older silicon.
Obtained from: Linux ath9k, Atheros
Reference code that shows how to get a packet's timestamp out of
cxgbe(4). Disabled by default because we don't have a standard way
today to pass this information up the stack.
The timestamp is 60 bits wide and each increment represents 1 tick of
the T4's core clock. As an example, the timestamp granularity is ~4.4ns
for this card:
# sysctl dev.t4nex.0.core_clock
dev.t4nex.0.core_clock: 228125
MFC after: 1 week
- Enable 5-tuple and every-packet lookup.
- Setup the default filter mode to allow filtering/steering based on IP
protocol, ingress port, inner VLAN ID, IP frag, FCoE, and MPS match
type; all combined together. You can also filter based on MAC index,
Ethernet type, IP TOS/IPv6 Traffic Class, and outer VLAN ID but you'll
have to modify the default filter mode and exclude some of the
match-fields in it.
IPv4 and IPv6 SIP/DIP/SPORT/DPORT are always available in all filter
rules.
- Add driver ioctls to get/set the global filter mode.
- Add driver ioctls to program and delete hardware filters. A couple of
the "switch" actions that rewrite Ethernet and VLAN information and
switch the packet out of another port may not work as the L2 code is not
yet in place. Everything else, including all "drop" and "pass" rules
with RSS or absolute qid, should work.
Obtained from: Chelsio Communications
have similar hardware features of BCM5718 family except the number
of receive return ring is 4. The BCM57765 family is known to
support IEEE 802.3az EEE(Energy Efficient Ethernet) but this change
does not include EEE support code. I hope EEE is implemented in
near future.
This change will support BCM57761, BCM57765, BCM57781, BCM57785,
BCM57791 and BCM57795. All hardware offloading features are
supported and suspend/resume also should work.
Many thanks to Broadcom for continuing support of FreeBSD.
Tested by: Paul Thornton (prt <> prt dot org)
HW donated by: Broadcom
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
driver would verify that requests for child devices were confined to any
existing I/O windows, but the driver relied on the firmware to initialize
the windows and would never grow the windows for new requests. Now the
driver actively manages the I/O windows.
This is implemented by allocating a bus resource for each I/O window from
the parent PCI bus and suballocating that resource to child devices. The
suballocations are managed by creating an rman for each I/O window. The
suballocated resources are mapped by passing the bus_activate_resource()
call up to the parent PCI bus. Windows are grown when needed by using
bus_adjust_resource() to adjust the resource allocated from the parent PCI
bus. If the adjust request succeeds, the window is adjusted and the
suballocation request for the child device is retried.
When growing a window, the rman_first_free_region() and
rman_last_free_region() routines are used to determine if the front or
end of the existing I/O window is free. From using that, the smallest
ranges that need to be added to either the front or back of the window
are computed. The driver will first try to grow the window in whichever
direction requires the smallest growth first followed by the other
direction if that fails.
Subtractive bridges will first attempt to satisfy requests for child
resources from I/O windows (including attempts to grow the windows). If
that fails, the request is passed up to the parent PCI bus directly
however.
The PCI-PCI bridge driver will try to use firmware-assigned ranges for
child BARs first and only allocate a "fresh" range if that specific range
cannot be accommodated in the I/O window. This allows systems where the
firmware assigns resources during boot but later wipes the I/O windows
(some ACPI BIOSen are known to do this) to "rediscover" the original I/O
window ranges.
The ACPI Host-PCI bridge driver has been adjusted to correctly honor
hw.acpi.host_mem_start and the I/O port equivalent when a PCI-PCI bridge
makes a wildcard request for an I/O window range.
The new PCI-PCI bridge driver is only enabled if the NEW_PCIB kernel option
is enabled. This is a transition aide to allow platforms that do not
yet support bus_activate_resource() and bus_adjust_resource() in their
Host-PCI bridge drivers (and possibly other drivers as needed) to use the
old driver for now. Once all platforms support the new driver, the
kernel option and old driver will be removed.
PR: kern/143874 kern/149306
Tested by: mav
Rationale:
- unlike current behavior this seems to be compliant with OSS
specification:
http://manuals.opensound.com/developer/SNDCTL_DSP_GETIPTR.html
- this seems to meet expectations of some OSS programs compiled for or
ported from Linux, e.g. ALSA OSS plugin
- this doesn't seem to break any programs as far as current testing
shows
Tested by: nox, hselasky
MFC after: 4 days
sectors with all-zeroes.
The zeroes come from a static buffer; null(4) uses a dynamic buffer for
the same purpose (for /dev/zero). It might be a good idea to have a
static, shared, read-only all-zeroes page somewhere in the kernel that
md(4), null(4) and any other code that needs zeroes could use.
Reviewed by: kib
MFC after: 3 weeks
constraints on the rman and reject attempts to manage a region that is out
of range.
- Fix various places that set rm_end incorrectly (to ~0 or ~0u instead of
~0ul).
- To preserve existing behavior, change rman_init() to set rm_start and
rm_end to allow managing the full range (0 to ~0ul) if they are not set by
the caller when rman_init() is called.
For these devices, the number of supported ports is read from a register
in BAR 0.
PR: kern/134878
Submitted by: David Wood david of wood2 org uk
MFC after: 1 week
The AR9130 is an AR9160/AR5416 family WMAC which is glued directly
to the AR913x SoC peripheral bus (APB) rather than via a PCI/PCIe
bridge.
The specifics:
* A new build option is required to use the AR9130 - AH_SUPPORT_AR9130.
This is needed due to the different location the RTC registers live
with this chip; hopefully this will be undone in the future.
This does currently mean that enabling this option will break non-AR9130
builds, so don't enable it unless you're specifically building an image
for the AR913x SoC.
* Add the new probe, attach, EEPROM and PLL methods specific to Howl.
* Add a work-around to ah_eeprom_v14.c which disables some of the checks
for endian-ness and magic in the EEPROM image if an eepromdata block
is provided. This'll be fixed at a later stage by porting the ath9k
probe code and making sure it doesn't break in other setups (which
my previous attempt at this did.)
* Sprinkle Howl modifications throughput the interrupt path - it doesn't
implement the SYNC interrupt registers, so ignore those.
* Sprinkle Howl chip powerup/down throughout the reset path; the RTC methods
were
* Sprinkle some other Howl workarounds in the reset path.
* Hard-code an alternative setup for the AR_CFG register for Howl, that
sets up things suitable for Big-Endian MIPS (which is the only platform
this chip is glued to.)
This has been tested on the AR913x based TP-Link WR-1043nd mode, in
legacy, HT/20 and HT/40 modes.
Caveats:
* 2ghz has only been tested. I've not seen any 5ghz radios glued to this
chipset so I can't test it.
* AR5416_INTERRUPT_MITIGATION is not supported on the AR9130. At least,
it isn't implemented in ath9k. Please don't enable this.
* This hasn't been tested in MBSS mode or in RX/TX block-aggregation mode.
allocated, not the maximum number of messages the device supports. The
spec only requires the former, and I believe I implemented the latter due
to misunderstanding an e-mail. In particular, this fixes an issue where
having several devices that all support 16 messages can run out of
IDT vectors on x86 even though the driver only uses a single message.
Submitted by: Bret Ketchum bcketchum of gmail
MFC after: 1 week
adding appropriate #ifdefs. For module builds the framework needs
adjustments for at least carp.
Reviewed by: gnn
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
MFC after: 4 days
the watchdog, via the watchdog(9) interface.
For that, the WD_LASTVAL bitwise operation is used. It is mutually
exclusive with any explicit timout passing to the watchdogs.
The last timeout can be returned via the wdog_kern_last_timeout()
KPI.
- Add the possibility to pat the watchdogs installed via the watchdog(9)
interface from the kernel.
In order to do that the new KPI wdog_kern_pat() is offered and it does
accept normalized nanoseconds or WD_LASTVAL.
- Avoid to pass WD_ACTIVE down in the watchdog handlers. All the control
bit processing should over to the upper layer functions and not passed
down to the handlers at all.
These changes are intended to be used in order to fix up the watchdog
tripping in situation when the userland is busted, but protection is still
wanted (examples: shutdown syncing / disk dumping).
Sponsored by: Sandvine Incorporated
Reviewed by: emaste, des, cognet
MFC after: 2 weeks
will generate a short terminated USB transfer if
the maximum NCM frame size is greater than what
the driver can handle.
Reported by: Matthias Benesch
MFC after: 7 days
Approved by: thompsa (mentor)
- Also a couple minor tweaks to the TX code from the same source.
- Add the INET ioctl code which has been missing from this driver,
and which caused IP aliases to reset the interface.
- Last, some minor logic changes that just reflect upcoming
hardware support, but have no other functional effect now.
MFC after a week
Writing the TX power registers is the same between all of these chips
and later NICs (AR9287, AR9271 USB, etc.) so this will reduce code
duplication when those NICs are added to the HAL.
spurious (and fatal) interrupt errors.
One user reported seeing this:
Apr 22 18:04:24 ceres kernel: ar5416GetPendingInterrupts: fatal error,
ISR_RAC 0x0 SYNC_CAUSE 0x2000
SYNC_CAUSE of 0x2000 is AR_INTR_SYNC_LOCAL_TIMEOUT which is a bus timeout;
this shouldn't cause HAL_INT_FATAL to be set.
After checking out ath9k, ath9k_ar9002_hw_get_isr() clears (*masked)
before continuing, regardless of whether any bits in the ISR registers
are set. So if AR_INTR_SYNC_CAUSE is set to something that isn't
treated as fatal, and AR_ISR isn't read or is read and is 0, then
(*masked) wouldn't be cleared. Thus any of the existing bits set
that were passed in would be preserved in the output.
The caller in if_ath - ath_intr() - wasn't setting the masked value
to 0 before calling ath_hal_getisr(), so anything that was present
in that uninitialised variable would be preserved in the case above
of AR_ISR=0, AR_INTR_SYNC_CAUSE != 0; and if the HAL_INT_FATAL bit
was set, a fatal condition would be interpreted and the chip was
reset.
This patch does the following:
* ath_intr() - set masked to 0 before calling ath_hal_getisr();
* ar5416GetPendingInterrupts() - clear (*masked) before processing
continues; so if the interrupt source is AR_INTR_SYNC_CAUSE
and it isn't fatal, the hardware isn't reset via returning
HAL_INT_FATAL.
This doesn't fix any underlying errors which trigger
AR_INTR_SYNC_LOCAL_TIMEOUT - which is a bus timeout of some
sort - so that likely should be further investigated.
- Centralize PCI resource allocation/release.
- Enable flowid (TSS) support.
- Added "per-fastpath" locks and watchdog timeouts.
- Fixed problem where the CQ producer index was advanced beyond
the size of the CQ ring during initialization.
- Replaced hard-coded debug levels in some debug print statements.
- More style(9) fixes.
MFC after: Two weeks
should respond with all zeroes to any access to slave registers. Test with
PATA devices confirmed such behavior. Unluckily, Intel SATA controllers in
legacy emulation mode behave differently, not making any difference between
ATA and ATAPI devices. It causes false positive slave device detection and,
as result, command timeouts.
To workaround this problem, mask result of legacy-emulated soft-reset with
the device presence information received from the SATA-specific registers.
- TCO_MESSAGEx: TCO specific regs providing the ability to monitor BIOS
bootup activity.
- TCO_NEWCENTURY: reporting RTC year roll over.
- TCO_NMI2SMI_EN, TCO_NMI_NOW: controlling SMIs conversion to NMIs and
NMI trigger.
- SMI_GBL_EN: Enabling SMI delivery for all the northbridge controller.
MFC after: 10 days
This improves hard-reset and hot-plug on these ports.
- Device with ID 0x29218086 is a 2-port variant of ICH9 in legacy mode.
Skip probing for nonexistent slave devices there.
It allows to avoid false positive device detection under Xen, that caused
long probe delays due to subsequent IDENTIFY command timeouts.
MFC after: 1 month
that could have allowed the hardware pidx to reach the cidx even though
the freelist isn't empty. (Haven't actually seen this but it was there
waiting to happen..)
MFC after: 1 week
now a suitable base for all kinds of egress queues.
- Add control queues (sge_ctrlq) and allocate one of these per hardware
channel. They can be used to program filters and steer traffic (and
more).
MFC after: 1 week
- If a ENH_SENS TLV section exit the firmware is capable of doing
enhanced sensitivity calibration.
- Newer devices/firmwares have more calibration commands therefore
hardcoding the noise gain/reset commands no longer works. It is
supposed to use the next index after the newest calibration type
support. Read the command index of the TLV section if available.
This support has not worked for several years, and is not likely to work
again, unless Intel decides to release a native FreeBSD version of their
compiler. ;)
