the 'debugging' section of any HEAD kernel and enable for the mainstream
ones, excluding the embedded architectures.
It may, of course, enabled on a case-by-case basis.
Sponsored by: Sandvine Incorporated
Requested by: emaste
Discussed with: kib
sync.
VIPT/PIPT caches need valid VA-PA mapping in PTE for a cache operation to
succeed (unlike VIVT). Prior to this fix pmap was using l2pte_valid() for that
check, but this is not sufficient as the function merely checks if a PTE
exists (there can be existing but _invalid_ entries in the table).
A new pmap_has_valid_mapping() routine is introduced to do this job right by
checking proper PTE flags.
Among other potential problems this cures coherency issues with L2 caches on
MV-78100.
Submitted by: Grzegorz Bernacki, Piotr Ziecik
Reviewed, tested by: marcel
Obtained from: Semihalf
MFC after: 1 week
frame of db_trace_self()) and not the caller's frame. The use
of builtin_frame_address(1) to get the caller's frame is not
reliable and can cause panics.
previously know by StarSemi STR9104.
Tested by the submitter on an Emprex NSD-100 board.
Submitted by: Yohanes Nugroho <yohanes at gmail.com>
Reviewed by: freebsd-arm, stas
Obtained from: //depot/projects/str91xx/...
This replaces d_mmap() with the d_mmap2() implementation and also
changes the type of offset to vm_ooffset_t.
Purge d_mmap2().
All driver modules will need to be rebuilt since D_VERSION is also
bumped.
Reviewed by: jhb@
MFC after: Not in this lifetime...
This brings hwpmc(4) support for 2nd and 3rd generation XScale cores.
Right now it's enabled by default to make sure we test this a bit.
When the time comes it can be disabled by default.
Tested on Gateworks boards.
A man page is coming.
Obtained from: //depot/user/rpaulo/xscalepmc/...
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
- Reorder detach so that ether_ifdetach() is called first. This removes
the race that ATE_FLAG_DETACHING closed, so that flag can be removed.
- Trim a duplicate clearing of IFF_DRV_RUNNING.
Reviewed by: imp
- Remove most of direct relations between ATA(4) peripherial and controller
levels. It makes logic more transparent and is a mandatory step to wrap
ATA(4) controller level into ATA-native CAM SIM.
- Tune AHCI and SATA2 SiI drivers memory allocation a bit to allow bigger
I/O transaction sizes without additional cost.
while in kernel mode, and later changing signal mask to block the
signal, was fixed for sigprocmask(2) and ptread_exit(3). The same race
exists for sigreturn(2), setcontext(2) and swapcontext(2) syscalls.
Use kern_sigprocmask() instead of direct manipulation of td_sigmask to
reschedule newly blocked signals, closing the race.
Reviewed by: davidxu
Tested by: pho
MFC after: 1 month
the memory or D-cache, depending on the semantics of the platform.
vm_sync_icache() is basically a wrapper around pmap_sync_icache(),
that translates the vm_map_t argumument to pmap_t.
o Introduce pmap_sync_icache() to all PMAP implementation. For powerpc
it replaces the pmap_page_executable() function, added to solve
the I-cache problem in uiomove_fromphys().
o In proc_rwmem() call vm_sync_icache() when writing to a page that
has execute permissions. This assures that when breakpoints are
written, the I-cache will be coherent and the process will actually
hit the breakpoint.
o This also fixes the Book-E PMAP implementation that was missing
necessary locking while trying to deal with the I-cache coherency
in pmap_enter() (read: mmu_booke_enter_locked).
The key property of this change is that the I-cache is made coherent
*after* writes have been done. Doing it in the PMAP layer when adding
or changing a mapping means that the I-cache is made coherent *before*
any writes happen. The difference is key when the I-cache prefetches.
- Move USB serial drivers earlier to match their placement in other kernel
configs.
- Add descriptions to various USB drivers.
- Move the USB wireless drivers into a new section.
- Add ulscom to the list of USB serial drivers.
by looking at the bases used for non-relocatable executables by gnu ld(1),
and adjusting it slightly.
Discussed with: bz
Reviewed by: kan
Tested by: bz (i386, amd64), bsam (linux)
MFC after: some time
pmap_dcache_wbinv_all/pmap_copy_page functions which we might want
to take advatage of later. This fixes the build with PMAP_DEBUG
defined.
Discussed with: cognet
first and the native ia32 compat as middle (before other things).
o(ld)brandinfo as well as third party like linux, kfreebsd, etc.
stays on SI_ORDER_ANY coming last.
The reason for this is only to make sure that even in case we would
overflow the MAX_BRANDS sized array, the native FreeBSD brandinfo
would still be there and the system would be operational.
Reviewed by: kib
MFC after: 1 month
Remove the altkstacks, instead instantiate threads with kernel stack
allocated with the right size from the start. For the thread that has
kernel stack cached, verify that requested stack size is equial to the
actual, and reallocate the stack if sizes differ [1].
This fixes the bug introduced by r173361 that was committed several days
after r173004 and consisted of kthread_add(9) ignoring the non-default
kernel stack size.
Also, r173361 removed the caching of the kernel stacks for a non-first
thread in the process. Introduce separate kernel stack cache that keeps
some limited amount of preallocated kernel stacks to lower the latency
of thread allocation. Add vm_lowmem handler to prune the cache on
low memory condition. This way, system with reasonable amount of the
threads get lower latency of thread creation, while still not exhausting
significant portion of KVA for unused kstacks.
Submitted by: peter [1]
Discussed with: jhb, julian, peter
Reviewed by: jhb
Tested by: pho (and retested according to new test scenarious)
MFC after: 1 week
allocated with the right size from the start. For the thread that has
kernel stack cached, verify that requested stack size is equial to the
actual, and reallocate the stack if sizes differ [1].
This fixes the bug introduced by r173361 that was committed several days
after r173004 and consisted of kthread_add(9) ignoring the non-default
kernel stack size.
Also, r173361 removed the caching of the kernel stacks for a non-first
thread in the process. Introduce separate kernel stack cache that keeps
some limited amount of preallocated kernel stacks to lower the latency
of thread allocation. Add vm_lowmem handler to prune the cache on
low memory condition. This way, system with reasonable amount of the
threads get lower latency of thread creation, while still not exhausting
significant portion of KVA for unused kstacks.
Submitted by: peter [1]
Discussed with: jhb, julian, peter
Reviewed by: jhb
Tested by: pho
MFC after: 1 week
- The device is based on Marvell 88F6281 system on chip.
- More info about the platform at http://www.plugcomputer.org
- To build the FreeBSD kernel:
make buildkernel TARGET_ARCH=arm KERNCONF=SHEEVAPLUG
- Installation notes at: http://wiki.freebsd.org/FreeBSDMarvell
Submitted by: Michal Hajduk
Obtained from: Semihalf
Modules on Marvell SOC can be selectively PM-disabled, and we must not access
disabled devices' registers (attempt to initialize them) unconditionally, as
this leads to the system hang. This patch introduces graceful handling of the
PM state during devices init.
Submitted by: Michal Hajduk
Obtained from: Semihalf
will initialize the FIFO memory correctly on attach. Before
that this values was intialized in only in at91_usart_bus_attach
which is called after the uart(4) memory allocation happens.
Approved by: re (kib)
MFC after: 1 week
vnet.h, we now use jails (rather than vimages) as the abstraction
for virtualization management, and what remained was specific to
virtual network stacks. Minor cleanups are done in the process,
and comments updated to reflect these changes.
Reviewed by: bz
Approved by: re (vimage blanket)
a device pager (OBJT_DEVICE) object in that it uses fictitious pages to
provide aliases to other memory addresses. The primary difference is that
it uses an sglist(9) to determine the physical addresses for a given offset
into the object instead of invoking the d_mmap() method in a device driver.
Reviewed by: alc
Approved by: re (kensmith)
MFC after: 2 weeks
On some ARM variations CPU func dispatcher has the D-cache invalidate method
point to write-back invalidate, which is wrong, and can lead to a crash/panic
on affected platforms.
Spotted by: HPS
Reviewed by: cognet
Approved by: re (kib)
a) nocache-remap problem
When a page is remapped into a non-cacheable virtual memory region there
was no associated write-back invalidate operation performed. We remove
writeback of the original buffer size from bus_dmamem_alloc() and add
appropriate L1/L2 flush operation.
b) missing write-back invalidate operation
In pmap_kremove a page is removed so we must do a write-back
invalidate operation aligned to the page virtual address.
Submitted by: Michal Hajduk
Reviewed by: Mark Tinguely, rpaulo, stas
Approved by: re (kib)
Obtained from: Semihalf
dependent memory attributes:
Rename vm_cache_mode_t to vm_memattr_t. The new name reflects the
fact that there are machine-dependent memory attributes that have
nothing to do with controlling the cache's behavior.
Introduce vm_object_set_memattr() for setting the default memory
attributes that will be given to an object's pages.
Introduce and use pmap_page_{get,set}_memattr() for getting and
setting a page's machine-dependent memory attributes. Add full
support for these functions on amd64 and i386 and stubs for them on
the other architectures. The function pmap_page_set_memattr() is also
responsible for any other machine-dependent aspects of changing a
page's memory attributes, such as flushing the cache or updating the
direct map. The uses include kmem_alloc_contig(), vm_page_alloc(),
and the device pager:
kmem_alloc_contig() can now be used to allocate kernel memory with
non-default memory attributes on amd64 and i386.
vm_page_alloc() and the device pager will set the memory attributes
for the real or fictitious page according to the object's default
memory attributes.
Update the various pmap functions on amd64 and i386 that map pages to
incorporate each page's memory attributes in the mapping.
Notes: (1) Inherent to this design are safety features that prevent
the specification of inconsistent memory attributes by different
mappings on amd64 and i386. In addition, the device pager provides a
warning when a device driver creates a fictitious page with memory
attributes that are inconsistent with the real page that the
fictitious page is an alias for. (2) Storing the machine-dependent
memory attributes for amd64 and i386 as a dedicated "int" in "struct
md_page" represents a compromise between space efficiency and the ease
of MFCing these changes to RELENG_7.
In collaboration with: jhb
Approved by: re (kib)
o add to platforms where it was missing (arm, i386, powerpc, sparc64, sun4v)
o define as "1" on amd64 and i386 where there is no restriction
o make the type returned consistent with ALIGN
o remove _ALIGNED_POINTER
o make associated comments consistent
Reviewed by: bde, imp, marcel
Approved by: re (kensmith)
DPCPU area was not properly mapped into kernel VA space, which caused page
fault on the first DPCPU access. This patch fixes the problem by mapping DPCPU
area into kernel VA space.
Submitted by: Michal Hajduk, Piotr Ziecik
Reviewed by: cognet, stas
Approved by: re (kib)
Obtained from: Semihalf
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
required by video card drivers. Specifically, this change introduces
vm_cache_mode_t with an appropriate VM_CACHE_DEFAULT definition on all
architectures. In addition, this changes adds a vm_cache_mode_t parameter
to kmem_alloc_contig() and vm_phys_alloc_contig(). These will be the
interfaces for allocating mapped kernel memory and physical memory,
respectively, with non-default cache modes.
In collaboration with: jhb
- Modules and kernel code alike may use DPCPU_DEFINE(),
DPCPU_GET(), DPCPU_SET(), etc. akin to the statically defined
PCPU_*. Requires only one extra instruction more than PCPU_* and is
virtually the same as __thread for builtin and much faster for shared
objects. DPCPU variables can be initialized when defined.
- Modules are supported by relocating the module's per-cpu linker set
over space reserved in the kernel. Modules may fail to load if there
is insufficient space available.
- Track space available for modules with a one-off extent allocator.
Free may block for memory to allocate space for an extent.
Reviewed by: jhb, rwatson, kan, sam, grehan, marius, marcel, stas
driver's i/o ops must be locked to avoid chaos. Extend the cambria
bus tag to support ata and add a spin lock. The ata driver is
hacked to use that instead of it's builtin hack for ixp425. Once
the ata driver is fixed to not be confused about byte order we can
generalize the cambria bus tag code and make it generally useful.
While here take advantage of our being ixp435-specific to remove
delays when switching between byte+word accesses and to eliminate
the 2us delay for the uarts (the spin lock overhead looks to do
this for us).
used for the optional GPS+RS485 uarts on the Gateworks Cambria boards
which otherwise are unreliable
o setup the hack bus space tag for the GPS+RS485 uarts
o program the gpio interrupts for the uarts to be edge-rising
o force timing on the expansion bus for the uarts to be "slow"
Thanks to Chris Lang of Gateworks for these tips.
structure. When the page is shared, the kernel mapping becomes a special
type of managed page to force the cache off the page mappings. This is
needed to avoid stale entries on all ARM VIVT caches, and VIPT caches
with cache color issue.
Submitted by: Mark Tinguely
Reviewed by: alc
Tested by: Grzegorz Bernacki, thompsa
causes both to become inoperative; this apparently was done by the original
IAL code as a workaround for IMEM parity errors which we've not seen so
just disable the reset.
Note this problem does not occur on IXP425 boards. The linux driver does
fuse-resets on each NPE but in the order NPE-A < NPE-B < NPE-C (when probing
for which NPE's are present/operational); we may want to switch to a similar
scheme but for now disable the resets until we see an issue.
normally taken from the hints file so this should have no effect
o set the port address "just in case"
o add NPE-A support to the tx done qmgr callback
so that it isn't exposured unless needed. In particular this means
that it's easier to tune the memory layout based on board details.
While here, remove inclusion of <machine/intr.h> from mvreg.h. This
also contains exposure to SoC specifics in MI drivers, because NIRQ
depends on the SoC.
the implementation can guarantee forward progress in the event of
a stuck interrupt or interrupt storm. This is especially critical
for fast interrupt handlers, as they can cause a hard hang in that
case. When first called, arm_get_next_irq() is passed -1.
Obtained from: Juniper Networks, Inc.
When pages are removed from virtual address space by calling pmap_remove_all()
CPU caches were not invalidated, which led to read corruption when another
page got mapped at this same virtual address at later time (the CPU was
retrieving stale contents).
Submitted by: Piotr Ziecik
Obtained from: Semihalf
CPU for too long period than necessary. Additively, interfaces are kept
polled (in the tick) even if no more packets are available.
In order to avoid such situations a new generic mechanism can be
implemented in proactive way, keeping track of the time spent on any
packet and fragmenting the time for any tick, stopping the processing
as soon as possible.
In order to implement such mechanism, the polling handler needs to
change, returning the number of packets processed.
While the intended logic is not part of this patch, the polling KPI is
broken by this commit, adding an int return value and the new flag
IFCAP_POLLING_NOCOUNT (which will signal that the return value is
meaningless for the installed handler and checking should be skipped).
Bump __FreeBSD_version in order to signal such situation.
Reviewed by: emaste
Sponsored by: Sandvine Incorporated
The system hostname is now stored in prison0, and the global variable
"hostname" has been removed, as has the hostname_mtx mutex. Jails may
have their own host information, or they may inherit it from the
parent/system. The proper way to read the hostname is via
getcredhostname(), which will copy either the hostname associated with
the passed cred, or the system hostname if you pass NULL. The system
hostname can still be accessed directly (and without locking) at
prison0.pr_host, but that should be avoided where possible.
The "similar information" referred to is domainname, hostid, and
hostuuid, which have also become prison parameters and had their
associated global variables removed.
Approved by: bz (mentor)
possible future I-cache coherency operation can succeed. On ARM
for example the L1 cache can be (is) virtually mapped, which
means that any I/O that uses temporary mappings will not see the
I-cache made coherent. On ia64 a similar behaviour has been
observed. By flushing the D-cache, execution of binaries backed
by md(4) and/or NFS work reliably.
For Book-E (powerpc), execution over NFS exhibits SIGILL once in
a while as well, though cpu_flush_dcache() hasn't been implemented
yet.
Doing an explicit D-cache flush as part of the non-DMA based I/O
read operation eliminates the need to do it as part of the
I-cache coherency operation itself and as such avoids pessimizing
the DMA-based I/O read operations for which D-cache are already
flushed/invalidated. It also allows future optimizations whereby
the bcopy() followed by the D-cache flush can be integrated in a
single operation, which could be implemented using on-chips DMA
engines, by-passing the D-cache altogether.
registers contents.
- Use memory barriers to preserve the order of buffer space operations.
This might be needed if we'll ever use this driver on architectures
where ordering is not guaranteed.
used in some cases):
- Ignore DMA tag boundaries when allocating bounce pages. The boundaries
don't determine whether or not parts of a DMA request bounce. Instead,
they are just used to carve up segments.
- Allow tags with sub-page alignment to share bounce pages since bounce
pages are always page aligned.
Reviewed by: scottl (amd64)
MFC after: 1 month
operates in the common memory mode and use polling mode to control
the status of operations as I don't have any board with interrupt
line routed yet. I'll add the GPIO interrupt driven mode as soon
as I get one.
respectivly. This will allow one to have a kernel with both devices
present and use it for multiple boards with different types of RTC
sitting on a bus.
Discussed with: imp
a fair number of static data structures, making this an unlikely
option to try to change without also changing source code. [1]
Change default cache line size on ia64, sparc64, and sun4v to 128
bytes, as this was what rtld-elf was already using on those
platforms. [2]
Suggested by: bde [1], jhb [2]
MFC after: 2 weeks
CACHE_LINE_SIZE constant. These constants are intended to
over-estimate the cache line size, and be used at compile-time
when a run-time tuning alternative isn't appropriate or
available.
Defaults for all architectures are 64 bytes, except powerpc
where it is 128 bytes (used on G5 systems).
MFC after: 2 weeks
Discussed on: arch@
a tag that has BUS_DMA_KEEP_PG_OFFSET set. Otherwise the page could be
reused with a non-zero offset by a tag that doesn't have
BUS_DMA_KEEP_PG_OFFSET leading to data corruption.
Sleuthing by: avg
Reviewed by: scottl
at91_udp.c does not exist anymore, it is now replaced by at91dci in
src/sys/dev/usb/controller. Also remove the ohci_atmelarm.c because it is also
included in src/sys/conf/files
Submitted by: Sylvestre Gallon
1) Move the new field (brand_note) to the end of the Brandinfo structure.
2) Add a new flag BI_BRAND_NOTE that indicates that the brand_note pointer
is valid.
3) Use the brand_note field if the flag BI_BRAND_NOTE is set and as old
modules won't have the flag set, so the new field brand_note would be
ignored.
Suggested by: jhb
Reviewed by: jhb
Approved by: kib (mentor)
MFC after: 6 days
but I see no benefit from it today.
VM_PROT_READ_IS_EXEC was only intended for use on processors that do not
distinguish between read and execute permission. On an mmap(2) or
mprotect(2), it automatically added execute permission if the caller
specified permissions included read permission. The hope was that this
would reduce the number of vm map entries needed to implement an address
space because there would be fewer neighboring vm map entries that differed
only in the presence or absence of VM_PROT_EXECUTE. (See vm/vm_mmap.c
revision 1.56.)
Today, I don't see any real applications that benefit from
VM_PROT_READ_IS_EXEC. In any case, vm map entries are now organized
as a self-adjusting binary search tree instead of an ordered list. So,
the need for coalescing vm map entries is not as great as it once was.
to the virtual one. I may had a reason at some point to use the later, but
can't remember which, and it can leads to issues.
Reported by: Guillaume Ballet <gballet gmail com>
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
to the full path of the image that is being executed.
Increase AT_COUNT.
Remove no longer true comment about types used in Linux ELF binaries,
listed types contain FreeBSD-specific entries.
Reviewed by: kan
".note.ABI-tag" section.
The search order of a brand is changed, now first of all the
".note.ABI-tag" is looked through.
Move code which fetch osreldate for ELF binary to check_note() handler.
PR: 118473
Approved by: kib (mentor)
operate on the resource (we have no local resources to manage); this
fixes drivers that alloc/release resources in their probe method and
then do it again in attach
o while here add some prints to catch failures and massage style a bit
o encode need for A4 bus space tag hackery according to the memory
address; checking for "uart" breaks down with the GPS chip support
which is also a uart but does not require the same hackery
o encode the correct memory window instead of carving up all of i/o
space, potentially with a larger window than a device should have;
this likely should be handled in the drivers by using a proper bus
alloc call but since some drivers depend on the bus support to figure
this out we cannot simply mod them
o add optional GPS and RS485 support (conditionally as the support
isn't ready yet)
o improves understandability by replacing numerous relative address
calculations with fixed addresses; everything should now match up
more easily with the vm layout shown at the top of the file
o move the expansion bus chip select regions to be contiguous with
the expansion bus configuration area; this is not exploited right
now but allows map consolidation in the future
o leave a gap between the expansion bus regions and the pci config
space in case we want to map more exp bus cs regions
Reviewed by: imp, thompsa
usb stack rather than with the rest of the processor support code.
Not sure that's a good idea, as we were moving away from it, but this
fixes the build in the mean time so we can have that discussion.
the same dma tag. However, it can happen multiple dma tags share the same
bounce zone too, so add a per-bounce zone map counter, and check it instead of
the dma tag map counter, to know if we have to alloc more pages.
Reported by: miwi
Reviewed by: scottl
offset. This is needed for the ehci hardware buffer rings that assume
this behavior.
This is an interim solution, and a more general one is being worked
on. This solution doesn't break anything that doesn't ask for it
directly. The mbuf and uio variants with this flag likely don't work
and haven't been tested.
Universe builds with these changes. I don't have a huge-memory
machine to test these changes with, but will be happy to work with
folks that do and hps if this changes turns out not to be sufficient.
Submitted by: alfred@ from Hans Peter Selasky's original
o add bus shim for cfi driver
o add static mapping for CS0 (we map all 16M as the cfi driver doesn't
support demand mapping)
Note this needs some tweaking to work for 2358 boards which is why the
CAMBRIA config is not touched.
rather than a fixed 512... This fixes the mount root problem on at91.
Prior to the SD card reorg, all data transfers were 512 bytes, so we
didn't notice.
the serial port class when we set the devclass since it is now
no-longer a compile time constant. Eliminate the pci include, as it
isn't relevant or necessary.
time constant. This allows us to potentially change it at runtime or
autodetect it early in the boot (the latter being much more likely to
have a good outcome).
o Only set 4-bit caps on those boards that have 4-bit caps (this means that
because we don't set wire4 yet, this forces us to always use 1-bit bus).
o Don't test wire4 when setting up the bus width, since bad things will
happen if we do.
# This likely won't fix the busted at91 sd card support, but these are
# needful changes for correctness.
- The contents of 'feroceon_cpufuncs' dispatch table was really dedicated for the
new Sheeva CPU (in 88F6xxx and MV-78xxx SOCs), and NOT Feroceon.
- Feroceon CPU (in 88F5xxx SOCs) appears as a regular ARM926EJ-S core and does
not require dedicated routines.
This will be accompanied by a file rename commit.
- Provide dedicated rmans for MEM and IO resources.
- Convert PCI IRQ routing info into a table (from callback approach), provide
config data for alternative DB- boards.
- Fix a wrong boundary check error in pcib_mbus_init_bar()
Obtained from: Semihalf
- Allow for setting per platform MPP/GPIO configuration in the kernel, so
that we can override all settings firmware might set.
- Set decode windows for the remaining on-chip peripherals: CESA, SATA and XOR.
- Improve handling of USB controllers so that all port are available on the
given SOC/platform (e.g. up to three on DB-78xxx), this includes rework of
USB decode windows set-up.
- Other minor fixes and cosmetics.
Obtained from: Semihalf
- Clean up TCLK handling so that it's dynamically recognized depending on
registers settings or chip version/revision. Update registers definitions.
- Teach SOC ident routine about A0 (initial silicon version for general
audience)
Obtained from: Marvell, Semihalf
options. Using the already included std.avila is not considered
to be entirely right (and the options slightly differ) but the best
match we currently have. Upcoming work should fit better.
Reorder another variable to match the layout of other configs.
Reviewed by: sam, warner (earlier version with options removed)
