o improves understandability by replacing numerous relative address
calculations with fixed addresses; everything should now match up
more easily with the vm layout shown at the top of the file
o move the expansion bus chip select regions to be contiguous with
the expansion bus configuration area; this is not exploited right
now but allows map consolidation in the future
o leave a gap between the expansion bus regions and the pci config
space in case we want to map more exp bus cs regions
Reviewed by: imp, thompsa
o add bus shim for cfi driver
o add static mapping for CS0 (we map all 16M as the cfi driver doesn't
support demand mapping)
Note this needs some tweaking to work for 2358 boards which is why the
CAMBRIA config is not touched.
o check feature bits when probing NPE ethernet support
o move firmware loading logic from if_npe to core npe support
o allow multiple refs to core NPE driver
o while here fix hw.npe.debug tunable path
o add definitions for more bits, for masking out IXP465-specific bits,
and %b format string
o add ixp4xx_read_feature_bits to retrieve the mask of valid features
(aka fuse bits)
o add cpu_is_ixp42x() macro
o print feature bits at boot
o recognize ixp435 cpu
o change memory layout for for ixp4xx to not assume memory is aliases
to 0x10000000 (Cambria/ixp435 memory starts at zero)
o handle 64 irqs for ixp435
o dual EHCI USB 2.0 controller integral to ixp435
o overhaul NPE code for ixp435 and better MAC+MII naming
o updated NPE firmware (including NPE-A image for ixp435/ixp465)
o Gateworks Cambria board support:
- IDE compact flash
- MCU
- front panel LED on i2c bus
- Octal LED latch
Sanity-tested with NFS-root on Avila and Cambria boards. Requires
pending boot2 mods for CF-boot on Cambria.
- Just grab Giant in the ixp425_iic(4) driver since this driver uses
a shared address/data register window pair to access the actual
I2C registers. None of the other ixp425 drivers lock access to these
shared address/data registers yet and that would need to be done before
this could use any meaningful locking.
- Add locking to the interrupt handler and 'iicbus_reset' methods of the
at91_twi(4) driver.
- Add locking to the pcf(4) driver. Other pcf(4) fixes include:
- Don't needlessly zero the softc.
- Use bus_foo rather than bus_space_foo and remove bus space tag and
handle from softc.
- The lpbb(4) driver just grabs Giant for now. This will be refined later
when ppbus(4) is locked.
- As was done with smbus earlier, move the DRIVER_MODULE() lines to match
the bus driver (either iicbus or iicbb) to the bridge driver into the
bridge drivers.
Tested by: sam (arm/ixp425)
boards. This is enough to net-boot to multiuser.
Also supported is the SMSC LAN91C111 parts used on the netCF, netDUO and netMMC
add-on boards.
I'll be putting some instructions on how to boot this on the Gumstix boards
online soon.
This is still fairly rough and will be refined over time but I felt it was
better to get this out there where other people can help out.
- Pull all the code to deal with the trampoline stuff into one
centeralized place and use it from everywhere.
- Some minor style tidiness
Reviewed by: tinguely
platform, so use the latter in preference to the former. This makes
the fake_preload setup be the same between kb920x_machdep.c and
avila_machdep.c....
layouts different than the defaults:
o hint.npe.0.mac="A", "B", etc. specifies the window for MAC register accesses
o hint.npe.0.mii="A", "B", etc. specifies PHY registers
o hint.npe.1.phy=%d specifies the PHY to map to a port
This allows devices like NSLU to be setup w/o code changes and will
also be used for forthcoming support for more Avila boards.
Reviewed by: imp
MFC after 1 week
While the KSE project was quite successful in bringing threading to
FreeBSD, the M:N approach taken by the kse library was never developed
to its full potential. Backwards compatibility will be provided via
libmap.conf for dynamically linked binaries and static binaries will
be broken.
silent NULL pointer dereference in the i386 and sparc64 pmap_pinit()
when the kmem_alloc_nofault() failed to allocate address space. Both
functions now return error instead of panicing or dereferencing NULL.
As consequence, vmspace_exec() and vmspace_unshare() returns the errno
int. struct vmspace arg was added to vm_forkproc() to avoid dealing
with failed allocation when most of the fork1() job is already done.
The kernel stack for the thread is now set up in the thread_alloc(),
that itself may return NULL. Also, allocation of the first process
thread is performed in the fork1() to properly deal with stack
allocation failure. proc_linkup() is separated into proc_linkup()
called from fork1(), and proc_linkup0(), that is used to set up the
kernel process (was known as swapper).
In collaboration with: Peter Holm
Reviewed by: jhb
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
After discussion with Sam, switch back to use firmware(9) instead of
having the firmware in hex format.
Put the binary firmware uuencoded into sys/contrib/dev/npe, and slap a
LICENSE file, as found on the Intel website.
Approved by: re (blanket), mux (mentor)
MFC After: 1 week
release number up to the max. This should eliminate the need to
tweak the default imageid define for later releases that are found
on the Intel web site.
MFC after: 1 month
quirky code: uarts, led, cf/ide, ixpqmgr, npe are now specified with hints.
May want to put some of these devices back in the code and just use hints
to override/specify configuration.
MFC after: 1 month
should setup is the class. This corrects an issue where enabling
uart1 on the avila board caused uart0 to stop working during boot
(no msgs generated by rc scripts were displayed).
Reviewed by: imp
MFC after: 3 weeks
it obtained through the uart_class structure. This allows us
to declare the uart_class structure as weak and as such allows
us to reference it even when it's not compiled-in.
It also allows is to get the uart_ops structure by name, which
makes it possible to implement the dt tag handling in uart_getenv().
The side-effect of all this is that we're using the uart_class
structure more consistently which means that we now also have
access to the size of the bus space block needed by the hardware
when we map the bus space, eliminating any hardcoding.
watchdog might hide the succesful arming of an earlier one. Accept that on
failing to arm any watchdog (because of non-supported timeouts) EOPNOTSUPP is
returned instead of the more appropriate EINVAL.
MFC after: 3 days
the alternate status and the control registers. Remove the local
version of ata_reset.
Add support for the ADI Pronghorn Metro boards. They use CS3 and CS4
instead of Avila's CS1 and CS2.
the alternate status and the control registers. Remove the local
version of ata_reset.
Add support for the ADI Pronghorn Metro boards. They use CS3 and CS4
instead of Avila's CS1 and CS2.
OKed by: sam, cognet
a version that i posted earlier on the -current mailing list,
and subsequent feedback received.
The core of the change is just in sys/firmware.h and kern/subr_firmware.c,
while other files are just adaptation of the clients to the ABI change
(const-ification of some parameters and hiding of internal info,
so this is fully compatible at the binary level).
In detail:
- reduce the amount of information exported to clients in struct firmware,
and constify the pointer;
- internally, document and simplify the implementation of the various
functions, and make sure error conditions are dealt with properly.
The diffs are large, but the code is really straightforward now (i hope).
Note also that there is a subtle issue with the implementation of
firmware_register(): currently, as in the previous version, we just
store a reference to the 'imagename' argument, but we should rather
copy it because there is no guarantee that this is a static string.
I realised this while testing this code, but i prefer to fix it in
a later commit -- there is no regression with respect to the past.
Note, too, that the version in RELENG_6 has various bugs including
missing locks around the module release calls, mishandling of modules
loaded by /boot/loader, and so on, so an MFC is absolutely necessary
there. I was just postponing it until this cleanup to avoid doing
things twice.
MFC after: 1 week
PCI bus' one as the default one, and explicitely use the other one for
non-PCI devices.
This is needed because the PCI bus can only address 64MB of RAM, while some
IXP425 boards have 128MB or more, and most of the PCI drivers do not bother
providing the parent dma tag.
behave as expected.
Also:
- Return an error if WD_PASSIVE is passed in to the ioctl as only
WD_ACTIVE is implemented at the moment. See sys/watchdog.h for an
explanation of the difference between WD_ACTIVE and WD_PASSIVE.
- Remove the I_HAVE_TOTALLY_LOST_MY_SENSE_OF_HUMOR define. If you've
lost your sense of humor, than don't add a define.
Specific changes:
i80321_wdog.c
Don't roll your own passive watchdog tickle as this would defeat the
purpose of an active (userland) watchdog tickle.
ichwd.c / ipmi.c:
WD_ACTIVE means active patting of the watchdog by a userland process,
not whether the watchdog is active. See sys/watchdog.h.
kern_clock.c:
(software watchdog) Remove a check for WD_ACTIVE as this does not make
sense here. This reverts r1.181.
(somewhat) meaningful message and terminate the build. It'd be
nice to print a proper URL from which to fetch the file but that
seems problematic. Leave a suggested starting point in this file
(TBD: add it to the man page).
Submitted by: ru
Make part of John Birrell's KSE patch permanent..
Specifically, remove:
Any reference of the ksegrp structure. This feature was
never fully utilised and made things overly complicated.
All code in the scheduler that tried to make threaded programs
fair to unthreaded programs. Libpthread processes will already
do this to some extent and libthr processes already disable it.
Also:
Since this makes such a big change to the scheduler(s), take the opportunity
to rename some structures and elements that had to be moved anyhow.
This makes the code a lot more readable.
The ULE scheduler compiles again but I have no idea if it works.
The 4bsd scheduler still reqires a little cleaning and some functions that now do
ALMOST nothing will go away, but I thought I'd do that as a separate commit.
Tested by David Xu, and Dan Eischen using libthr and libpthread.
o ixp425 support
o NPE network driver (requires Intel microcode)
o h/w qmgr support
o True IDE compact flash over expansion bus
o pci (ath and hifn795x parts tested)
o xscale watchdog timer
o ds1672 RTC on i2c bus
o ad7418 voltage + temp monitoring on i2c bus
o uart
Work done together with cognet, kevlo, and jmg. Parts of
the ixp425 support obtaine/derived from netbsd.
Reviewed by: cognet, imp
MFC after: 1 month
whole the physical memory, cached, using 1MB section mappings. This reduces
the address space available for user processes a bit, but given the amount of
memory a typical arm machine has, it is not (yet) a big issue.
It then provides a uma_small_alloc() that works as it does for architectures
which have a direct mapping.