Setting the doze registers wasn't actually working, and was being masked by a
bad #ifdef. Since the #ifdef was fixed, now e500mc-based SoCs hang at idle.
Fix this by using the intended wait.
MFC after: 1 week
Summary:
This enables some features of the DIU, using a static configuration,
specified either via a 'edid' property on the 'display' FDT node, or a
'video-mode' environment variable (bootarg). 'video-mode' was chosen because it
matches u-boot's naming, so it can be set with:
setenv bootargs video-mode=${video-mode}
at the u-boot CLI.
Mouse cursor is not supported currently, as a hardware cursor is not supported
by framebuffer VT yet. Currently it only supports a 32bpp ARGB (actually BGRA)
format, and only a single composite plane, at up to 1280x1024.
Differential Revision: https://reviews.freebsd.org/D8022
Summary:
1) Attach problem - mpc85xx_probe() relies on fact that 0xfff0 mask matches all
QorIQ CPUs what is not true since e6500. This shall be reworked to match against
all supported CPUs.
2) There is no any reason for operating system to re-program or anyhow else
touch the LAWs programmed by firmware (u-boot). Right now mpc85xx_attach()
removes all LaW entries except for DRAM. This causes MCE to be generated when
later any of driver maps DTB-provided hardware addresses which do not exist
anymore because corresponding LaWs were removed.
Submitted by: Ivan Krivonos <int0dster_AT_gmail.com>
Differential Revision: https://reviews.freebsd.org/D7663
mpc85xx_map_dcsr() returns a vm_offset_t, not an error code.
mpc85xx_fix_errata() will gracefully exit if mpc85xx_map_dcsr() returns 0, as
that indicates an error (NULL pointer).
__syncicache() only syncs the icache on the current CPU, it doesn't touch the
cache on any other core. Replace the call with cpu_flush_dcache() instead.
Since bp_kernload is not touched again by the boot CPU in this code path, dcbf
is no less efficient than the dcbst from __syncicache() by invalidating the
cache line.
Summary:
u-boot, following the ePAPR specification, puts secondary cores into a
spinloop at boot, rather than leaving them shut off. It then relies on the host
OS to write the correct values to a special spin table, located in coherent
memory (on newer implementations), or noncoherent memory (older
implementations).
This supports both implementations of ePAPR, as well as continuing to support
non-ePAPR booting, by first attempting to use the spintable, and falling back to
expecting non-started CPUs.
Test Plan:
Booted on a P5020 board. Tested before and after the changes.
Before the changes, prints the error "SMP: CPU 1 already out of hold-off state!"
and panics shortly thereafter. After the changes, same boot method lets it
complete boot.
Reviewed by: nwhitehorn
MFC after: 2 weeks
Relnotes: Yes
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D7494
Summary:
MPC85XX and QorIQ are very similar. When the DPAA dTSEC driver was
added, QORIQ_DPAA was brought in as a config option to support the differences
in hardware register settings between QorIQ (e500mc-, e5500- based) SoCs and
QUICC (e500v1/e500v2-based) SoCs, particularly in the Local Access Window (LAW)
target settings.
Unify these settings using macros to hide details and ease porting, and use a
new function (mpc85xx_is_qoriq()) to distinguish between QorIQ and QUICC SoCs at
runtime.
An alternative to using the function could be to use a variable initialized at
platform attach time, which may incur less overhead at runtime. Since it's not
in the critical path once booted, this optimization doesn't seem necessary at
first pass.
Reviewed by: nwhitehorn
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D7294
Remove the use of fdt_data_to_res(), and instead construct the resources
manually. Additionally, avoid the 32-bit size limitation of fdt_data_get(), by
building physical addresses manually from the lbc ranges property.
Approved by: re@(gjb)
Summary:
PowerPC Book-E SMP is currently broken for unknown reasons. Pull in
Semihalf changes made c2012 for e500mc/e5500, which enables booting SMP.
This eliminates the shared software TLB1 table, replacing it with
tlb1_read_entry() function.
This does not yet support ePAPR SMP booting, and doesn't handle resetting CPUs
already released (ePAPR boot releases APs to a spin loop waiting on a specific
address). This will be addressed in the near future by using the MPIC to reset
the AP into our own alternate boot address.
This does include a change to the dpaa/dtsec(4) driver, to mark the portals as
CPU-private.
Test Plan:
Tested on Amiga X5000/20 (P5020). Boots, prints the following
messages:
Adding CPU 0, pir=0, awake=1
Waking up CPU 1 (dev=1)
Adding CPU 1, pir=20, awake=1
SMP: AP CPU #1 launched
top(1) shows CPU1 active.
Obtained from: Semihalf
Relnotes: Yes
Differential Revision: https://reviews.freebsd.org/D5945
OFW i2c probing requires a new method ofw_bus_get_node(), and the bus device is
assumed iichb. With these changes, i2c devices attached in fdt are probed and
attached automagically.
Import portions of the PowerPC OF PCI implementation into new file
"ofwpci.c", common for other platforms. The files ofw_pci.c and ofw_pci.h
from sys/powerpc/ofw no longer exist. All required declarations are moved
to sys/dev/ofw/ofwpci.h. This creates a new ofw_pci_write_ivar() function
and modifies some others methods. Most functions contain existing ppc
implementations in the majority unchanged. Now there is no need to have
multiple identical copies of methods for various architectures.
Requested by: jhibbits
Reviewed by: jhibbits, marius
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Differential Revision: https://reviews.freebsd.org/D4879
a DRIVER_MODULE() referencing mmc_driver has a MODULE_DEPEND() on mmc. This
is because the kernel linker only searches for symbols in dependent modules,
so loading sdhci_pci (and other bus-flavors of sdhci) would fail when mmc
was not compiled into the kernel (even if you hand-loaded mmc first).
(Thanks to jilles@ for providing the vital clue about the kernel linker.)
On some architectures, u_long isn't large enough for resource definitions.
Particularly, powerpc and arm allow 36-bit (or larger) physical addresses, but
type `long' is only 32-bit. This extends rman's resources to uintmax_t. With
this change, any resource can feasibly be placed anywhere in physical memory
(within the constraints of the driver).
Why uintmax_t and not something machine dependent, or uint64_t? Though it's
possible for uintmax_t to grow, it's highly unlikely it will become 128-bit on
32-bit architectures. 64-bit architectures should have plenty of RAM to absorb
the increase on resource sizes if and when this occurs, and the number of
resources on memory-constrained systems should be sufficiently small as to not
pose a drastic overhead. That being said, uintmax_t was chosen for source
clarity. If it's specified as uint64_t, all printf()-like calls would either
need casts to uintmax_t, or be littered with PRI*64 macros. Casts to uintmax_t
aren't horrible, but it would also bake into the API for
resource_list_print_type() either a hidden assumption that entries get cast to
uintmax_t for printing, or these calls would need the PRI*64 macros. Since
source code is meant to be read more often than written, I chose the clearest
path of simply using uintmax_t.
Tested on a PowerPC p5020-based board, which places all device resources in
0xfxxxxxxxx, and has 8GB RAM.
Regression tested on qemu-system-i386
Regression tested on qemu-system-mips (malta profile)
Tested PAE and devinfo on virtualbox (live CD)
Special thanks to bz for his testing on ARM.
Reviewed By: bz, jhb (previous)
Relnotes: Yes
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D4544
1) Include opt_platform.h to get QORIQ_DPAA. Otherwise the definition of
OCP85XX_TGTIF_LBC is incorrect.
2) The child resources are already allocated, just activate them, instead of
incorrectly remapping the memory regions (resource lists for lbc consist of the
virtual address of the child's resources, not the physical address).
Sponsored by: Alex Perez/Inertial Computing
Some MPC85xx GPIO controllers are compatible with QorIQ.
It may make more sense in the future to rename this and mpc85xx_gpio.c, as
mpc85xx_gpio.c appears to only be compatible with a few mpc85xx SoCs. All other
MPC85xx SoCs use the same controller as QorIQ.
Extract common code from PowerPC's ofw_pci
Import portions of the PowerPC OF PCI implementation into
new file "ofw_pci.c", common for other platforms. The files ofw_pci.c and
ofw_pci.h from sys/powerpc/ofw no longer exist. All required declarations
are moved to sys/dev/ofw/ofw_pci.h.
This creates a new ofw_pci_write_ivar() function and modifies
ofw_pci_nranges(), ofw_pci_read_ivar(), ofw_pci_route_interrupt()
methods.
Most functions contain existing ppc implementations in the majority
unchanged. Now there is no need to have multiple identical copies
of methods for various architectures.
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Reviewed by: jhibbits, mmel
Differential Revision: https://reviews.freebsd.org/D4879
This needs to return to the drawing board as it breaks both
PowerPC and Sparc64 build.
Pointed out by: jhibbits
This simplifies checking for default resource range for bus_alloc_resource(),
and improves readability.
This is part of, and related to, the migration of rman_res_t from u_long to
uintmax_t.
Discussed with: jhb
Suggested by: marcel
Import portions of the PowerPC OF PCI implementation into
new file "ofw_pci.c", common for other platforms. The files ofw_pci.c and
ofw_pci.h from sys/powerpc/ofw no longer exist. All required declarations
are moved to sys/dev/ofw/ofw_pci.h.
This creates a new ofw_pci_write_ivar() function and modifies
ofw_pci_nranges(), ofw_pci_read_ivar(), ofw_pci_route_interrupt() methods.
Most functions contain existing ppc implementations in the majority
unchanged. Now there is no need to have multiple identical copies
of methods for various architectures.
Submitted by: Marcin Mazurek <mma@semihalf.com>
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Reviewed by: jhibbits, mmel
Differential Revision: https://reviews.freebsd.org/D4879
Device trees mark lbc as compatible with simplebus. Since simplebus is passed
first, it attaches first. When lbc's pass (default pass) comes, the bus is
already attached to simplebus, so is skipped.
Sponsored by: Alex Perez/Inertial Computing
Summary:
Migrate to using the semi-opaque type rman_res_t to specify rman resources. For
now, this is still compatible with u_long.
This is step one in migrating rman to use uintmax_t for resources instead of
u_long.
Going forward, this could feasibly be used to specify architecture-specific
definitions of resource ranges, rather than baking a specific integer type into
the API.
This change has been broken out to facilitate MFC'ing drivers back to 10 without
breaking ABI.
Reviewed By: jhb
Sponsored by: Alex Perez/Inertial Computing
Differential Revision: https://reviews.freebsd.org/D5075
LBC block size can only be up to 4GB. The existing code already clamps it, but
mixes unsigned long and uint32_t. This works on 32-bit targets, but not 64-bit,
so isn't completely correct. This fixes the type confusion.
Newer Book-E cores (e500mc, e5500, e6500) do not support the WE bit in the MSR,
and instead delegate CPU idling to the SoC.
Perhaps in the future the QORIQ_DPAA option for the mpc85xx platform will become
a subclass, which will eliminate most of the #ifdef's.
This includes the following changes:
* SMP kickoff for QorIQ (tested on P5020)
* Errata fixes for some silicon revisions
* Enables L2 (and L3 if available) caches
Obtained from: Semihalf
Sponsored by: Alex Perez/Inertial Computing
Summary:
* Take advantage of NEW_PCIB to remove a lot of setup code.
* Fix some bugs related to multiple PCI bridges.
There's still room for more cleanup, and still some bugs leftover, but this
cleans up a lot.
Test Plan: Tested on P5020 board with IDT PCIe switch.
Differential Revision: https://reviews.freebsd.org/D4127
QorIQ SoCs (e5500 core, P5 family) have 2 BARs for local access windows, while
MPC85XX, and P1/P2 families use only a single BAR register.
This also adds the QORIQ_DPAA option, mutually exclusive to MPC85XX, to handle
this difference.
Obtained from: Semihalf
Sponsored by: Alex Perez/Inertial Computing
Make it clearer what each one means in the comments that define them.
IIC_BUSBSY was used in many places to mean two different things, either
"someone else has reserved the bus so you have to wait until they're done"
or "the signal level on the bus was not in the state I expected before/after
issuing some command".
Now IIC_BUSERR is used consistantly to refer to protocol/signaling errors,
and IIC_BUSBSY refers to ownership/reservation of the bus.
Summary:
Some systems are based around mpc85xx, but need special initialization. By
making the mpc85xx platform a base class, these systems can be platform
subclasses, and perform board-specific initialization in addition to the mpc85xx
initialization.
Test Plan:
Tested on my RB800. A platform class was created, and will be committed
separately.
Reviewed By: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D3305
Rather than special casing on PCIC_BRIDGE || PCIC_PROCESSOR, allow all
HDRTYPE_BRIDGE types.
Obtained from: Semihalf
Sponsored by: Alex Perez/Intertial Computing
Summary:
The Freescale PCIe Root Complex shows up as a Processor class device, PowerPC
subclass, so the generic PCI code ignores it for a bridge. This adds support
for it.
As part of this, update the Freescale PCI hostbridge driver, to allow probing
beyond the root complex, instead of only allowing "proper" PCI-PCI bridges.
Reviewers: #powerpc, marcel, nwhitehorn
Reviewed By: nwhitehorn
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2442
Relnotes: yes
a sub-node of nexus (ofwbus) rather than direct attach under nexus. This
fixes FDT on x86 and will make coexistence with ACPI on ARM systems easier.
SPARC is unchanged.
Reviewed by: imp, ian
Open Firmware-centric:
- Keep the static list of regions in platform.c instead of ofw_machdep.c
- Move various merging and sorting operations to platform.c as well
- Move apple_hacks code out of ofw_machdep.c and into platform_powermac.c,
where it belongs
- Move CHRP-specific dynamic-reconfiguration memory parsing into
platform_chrp.c instead of pretending it is shared code
it more flexible about how the CCSR range is found. With this change, the
stock MPC85XX will boot on a Routerboard 800.
Hardware donated by: Benjamin Perrault
add actual platform probing based on PVR. Still needs a little more work:
in particular, the CCRS setup should move here.
Also turn "bare" into a truly bare platform that doesn't pretend to know how
to do anything except get the memory map. This should also be enhanced to
process the FDT reserved memory list, but that is for another day.
fdtbus in most cases. This brings ARM and MIPS more in line with existing
Open Firmware platforms like sparc64 and powerpc, as well as preventing
double-enumeration of the OF tree on embedded PowerPC (first through nexus,
then through fdtbus).
This change is also designed to simplify resource management on FDT platforms
by letting there exist a platform-defined root bus resource_activate() call
instead of replying on fdtbus to do the right thing through fdt_bs_tag.
The OFW_BUS_MAP_INTR() and OFW_BUS_CONFIG_INTR() kobj methods are also
available to implement for similar purposes.
Discussed on: -arm, -mips
Tested by: zbb, brooks, imp, and others
MFC after: 6 weeks
- Remove explicit requirement that the SOC registers be found except as an
optimization (although the MPC85XX LAW drivers still require they be found
externally, which should change).
- Remove magic CCSRBAR_VA value.
- Allow bus_machdep.c's early-boot code to handle non 1:1 mappings and
systems not in real-mode or global 1:1 maps in early boot.
- Allow pmap_mapdev() on Book-E to reissue previous addresses if the
area is already mapped. Additionally have it check all mappings, not
just the CCSR area.
This allows the console on e500 systems to actually work on systems where
the boot loader was not kind enough to set up a 1:1 mapping before starting
the kernel.
#defines. This also has the advantage that it makes the names more
compact, iand also allows us to correct the non-uniform naming of
the PCIM_LINK_* defines, making them all consistent amongst themselves.
This is a mostly mechanical rename:
s/PCIR_EXPRESS_/PCIER_/g
s/PCIM_EXP_/PCIEM_/g
s/PCIM_LINK_/PCIEM_LINK_/g
When this is MFC'd, #defines will be added for the old names to assist
out-of-tree drivers.
Discussed with: jhb
MFC after: 1 week
o Save and clear the LTESR register in the interrupt handler.
o In lbc_read_reg(), return the saved LTESR register value if applicable
(i.e. when the saved value is not invalid (read: ~0U)).
o In lbc_write_reg(), clear the bits in the saved register when when it's
written to and when the asved value is not invalid.
o Also in lbc_write_reg(), the LTESR register is unlocked (in H/W) when
bit 1 of LTEATR is cleared. We use this to invalidate our saved LTESR
register value. Subsequent reads and write go to H/W directly.
While here:
o In lbc_read_reg() & lbc_write_reg(), add some belts and suspenders to
catch when register offsets are out of range.
o In lbc_attach(), initialize completely and don't leave something left
for lbc_banks_enable().
methods so that MI drvers can depend on us doing the right thing instead
of having to go around us and call MD code directly. See the FDT code for
example (not for long though).
1. Define all registers. These definitions are needed to support
the FCM driver for direct-connect NAND.
2. Repurpose lbc_read_reg() and lbc_write_reg() for use by localbus
attached device drivers. Use bus_space functions directly in the
lbc driver itself.
3. Be smarter about programming LAWs and mapping memory. The ranges
defined in the FDT are per bank (= chip select) and since we can
have up to 8 banks, we could easily use more than 8 LAWs or TLB
enrties when per-bank memory ranges need multiple LAWs or TLBs
due to alignment or size constraints.
We now combine all memory ranges into the fewest possible set of
contiguous regions and program the hardware for that. Thus, a
cleverly written FDT with 8 devices may still only need 1 LAW or
1 TLB entry. Note that the memory ranges can be assigned randomly
to the banks. We sort as we build to handle that.
4. Support the FCM when programming the OR register. This is mostly
for documention purposes as we do not have a way to define the
mode for a bank.
5. Remove Semihalf-ism: do not define DEBUG (only to undefine it
again).
FDT does not define all ranges possible for a particular node (e.g.
PCI).
While here, only update the trgt_mem and trgt_io pointers if there's
no error. This avoids that we knowingly write an invalid target (= -1).
sync performs a strict superset of the functions of eieio, so using both
is redundant. While here, expand bus barriers to all bus_space operations,
since many drivers do not correctly use bus_space_barrier().
In principle, we can also replace sync just with eieio, for a significant
performance increase, but it remains to be seen whether any poorly-written
drivers currently depend on the side effects of sync to properly function.
MFC after: 1 week
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
MPC8555(E) has 8 LAWs, so don't make that the default case. Current
processors have 12 LAWs so use that as the default instead.
o Determine the target ID of the PCI/PCI-X and PCI-E controllers in
a way that's more future proof. There's almost a perfect mapping
from HC register offset to target ID, so use that as the default.
Handle the MPC8548(E) specially, since it has a non-standard target
ID for the PCI-E controller. Don't worry about whether the processor
implements the target ID here, because we should not get called for
PCI/PCI-X or PCI-E host controllers that don't exist.
versions instead. They were never needed as bus_generic_intr() and
bus_teardown_intr() had been changed to pass the original child device up
in 42734, but the ISA bus was not converted to new-bus until 45720.
already supported nested PICs, but was limited to having a nested
AT-PIC only. With G5 support the need for nested OpenPIC controllers
needed to be added. This was done the wrong way and broke the MPC8555
eval system in the process.
OFW, as well as FDT, describe the interrupt routing in terms of a
controller and an interrupt pin on it. This needs to be mapped to a
flat and global resource: the IRQ. The IRQ is the same as the PCI
intline and as such needs to be representable in 8 bits. Secondly,
ISA support pretty much dictates that IRQ 0-15 should be reserved
for ISA interrupts, because of the internal workins of south bridges.
Both were broken.
This change reverts revision 209298 for a big part and re-implements
it simpler. In particular:
o The id() method of the PIC I/F is removed again. It's not needed.
o The openpic_attach() function has been changed to take the OFW
or FDT phandle of the controller as a second argument. All bus
attachments that previously used openpic_attach() as the attach
method of the device I/F now implement as bus-specific method
and pass the phandle_t to the renamed openpic_attach().
o Change powerpc_register_pic() to take a few more arguments. In
particular:
- Pass the number of IPIs specificly. The number of IRQs carved
out for a PIC is the sum of the number of int. pins and IPIs.
- Pass a flag indicating whether the PIC is an AT-PIC or not.
This tells the interrupt framework whether to assign IRQ 0-15
or some other range.
o Until we implement proper multi-pass bus enumeration, we have to
handle the case where we need to map from PIC+pin to IRQ *before*
the PIC gets registered. This is done in a similar way as before,
but rather than carving out 256 IRQs per PIC, we carve out 128
IRQs (124 pins + 4 IPIs). This is supposed to handle the G5 case,
but should really be fixed properly using multiple passes.
o Have the interrupt framework set root_pic in most cases and not
put that burden in PIC drivers (for the most part).
o Remove powerpc_ign_lookup() and replace it with powerpc_get_irq().
Remove IGN_SHIFT, INTR_INTLINE and INTR_IGN.
Related to the above, fix the Freescale PCI controller driver, broken
by the FDT code. Besides not attaching properly, bus numbers were
assigned improperly and enumeration was broken in general. This
prevented the AT PIC from being discovered and interrupt routing to
work properly. Consequently, the ata(4) controller stopped functioning.
Fix the driver, and FDT PCI support, enough to get the MPC8555CDS
going again. The FDT PCI code needs a whole lot more work.
No breakages are expected, but lackiong G5 hardware, it's possible
that there are unpleasant side-effects. At least MPC85xx support is
back to where it was 7 months ago -- it's amazing how badly support
can be broken in just 7 months...
Sponsored by: Juniper Networks
the existing code was very platform specific, and broken for SMP systems
trying to reboot from KDB.
- Add a new PLATFORM_RESET() method to the platform KOBJ interface, and
migrate existing reset functions into platform modules.
- Modify the OF_reboot() routine to submit the request by hand to avoid
the IPIs involved in the regular openfirmware() routine. This fixes
reboot from KDB on SMP machines.
- Move non-KDB reset and poweroff functions on the Powermac platform
into the relevant power control drivers (cuda, pmu, smu), instead of
using them through the Open Firmware backdoor.
- Rename platform_chrp to platform_powermac since it has become
increasingly Powermac specific. When we gain support for IBM systems,
we will grow a new platform_chrp.
The following systems are affected:
- MPC8555CDS
- MPC8572DS
This overhaul covers the following major changes:
- All integrated peripherals drivers for Freescale MPC85XX SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- This includes: LBC, PCI / PCI-Express, I2C, DS1553, OpenPIC, TSEC, SEC,
QUICC, UART, CFI.
- Thanks to the common FDT infrastrucutre (fdtbus, simplebus) we retire
ocpbus(4) driver, which was based on hard-coded config data.
Note that world for these platforms has to be built WITH_FDT.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
the internal interrupt sources as active-high. The internal interrupt
sources are disabled when programmed as active-low.
Note that the internal interrupts have no sense bit like the external
interrupts. We program them as edge-triggered to make sure we write a
0 value to a reserved register. It does not in any way say anything
about the sense of internal interrupt.
CPUs by default, and provide a functional version of BUS_BIND_INTR().
While here, fix some potential concurrency problems in the interrupt
handling code.
has all 4 implemented, but across the processors we now support all the
combinations. For example, the MPC8533 doesn't have a PCI controller
at 0xA0000, but does at 0xB0000.
1. checking whether there's a link before initializing devices
on the bus. When there's no link any access onto the bus
will wedge the CPU.
2. synthesizing the class & subclass so that the host controller
appears as a standard PCI bridge, rather than a PowerPC CPU.
PCI Express, rather than a bit-field (boolean). Saving the capability
pointer this way makes access to capability-specific configuration
registers easy and efficient.
programming I/F. New SoC designs have different device IDs, but
don't need special treatment. Consequently, we fail to probe and
attach for no other reason than not having added the device ID to
the code.
Bank on Freescale's sense of backward compatibility and assume
that if we find a host controller, we know how work with it.
This fixes detection of the PCI Express host controllers on
Freescale's QorIQ family of processors (P1, P2 and P4).
It turns LBC control registers were not programmed correctly on MPC85XX. We
were accessing bogus addresses as the base offset (OCP85XX_LBC_OFF) was
erroneously added during offset calculations. Effectively the state of LBC
control registers was not altered by the kernel initialization code, but
everything worked as long as we coincided to use the same settings (LBC decode
windows) as firmware has initialized.
Submitted by: Lukasz Wojcik
Reviewed by: marcel
Approved by: re (kensmith)
Obtained from: Semihalf
