Add to read link status register of UTP mode, to ensure link status of
mixed mode, for YT PHY.
Fixes: 1c44384fce ("net/ngbe: support custom PHY interfaces")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Remain the same max frame size after the device restarts.
Fixes: 07baabb6a5 ("net/ngbe: support MTU set")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Since firmware does not use the semaphore between software and firmware.
Remove useless unilateral semaphore setting.
Fixes: f501a195bd ("net/ngbe: initialize and validate EEPROM")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Rename rx_oversize_errors to rx_oversize_cnt since it depends on giant
packet size limit instead of MTU, by hardware design.
Rename rx_drop_packets and tx_drop_packets to rx_dma_drop and tx_dma_drop
to indicate the drop location.
And add tx_dma_drop to extended statistics.
Fixes: 8b433d04ad ("net/ngbe: support device xstats")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
The pci bus interface is for drivers only.
Mark as internal and move the header in the driver headers list.
While at it, cleanup the code:
- fix indentation,
- remove unneeded reference to bus specific singleton object,
- remove unneeded list head structure type,
- reorder the definitions and macro manipulating the bus singleton object,
- remove inclusion of rte_bus.h and fix the code that relied on implicit
inclusion,
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Fix to read and write the correct register fields for yt8521s and
yt8531s PHY, since mode check was added.
Fixes: 1c44384fce ("net/ngbe: support custom PHY interfaces")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Add to read efuse values from flash, and disable EEE to improve signal
quality. Remove PHY semaphore to access PHY registers faster. And remove
unnecessary page selection where quick access is required.
When rte_eth_link_get_nowait() is called frequently with LSC disabled by
self-developed applications, eventually the PHY status register will be
accessed frequently. It will cause internal PHY init failure, if they
are done simultaneously. So there is a protection added for internal PHY
init.
Fixes: 3518df5774 ("net/ngbe: support device start/stop")
Fixes: 91bc12c522 ("net/ngbe: optimize PHY initialization process")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
When using mailbox to request firmware to enable or disable PCIe bus
master, there is a small probability that mailbox cannot respond.
Change to use rte_pci_read_config() and rte_pci_write_config(), to
avoid this problem.
Fixes: ac6c5e9af5 ("net/ngbe: fix Tx hang on queue disable")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
For M88E1512 PHY mixed mode, PXE driver overrides PHY mode at load
time. To workaround this problem, change to read PHY mode from flash
instead of register.
Fixes: 1c44384fce ("net/ngbe: support custom PHY interfaces")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
External PHY cannot power down after LAN reset, so need to manually
power down when device stopped.
Fixes: 3d0af70667 ("net/ngbe: setup PHY link")
Fixes: 1c44384fce ("net/ngbe: support custom PHY interfaces")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Change to check low ID register to determine the valid PHY address,
for yt8521s PHY with high ID register value 0. And fix polling
register when expect value is 0, to complete MDIO read.
Fixes: 44e97550ca ("net/ngbe: identify and reset PHY")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Remove 'DEBUGFUNC' due to too many invalid debug log prints, unify the
DEBUG level macros.
Fixes: cc934df178 ("net/ngbe: add log and error types")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Support to get OEM customized LED configuration information from firmware.
And driver needs to adjust the process of PHY setup link, based on this
LED configuration.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Add commands requesting firmware to enable or disable PCIe bus master.
Disable PCIe master access to clear BME when stop hardware, and verify
there are no pending requests.
Move disabling Tx queue after disabling PCIe bus master, to ensure that
there are no packets left to cause Tx hang.
Fixes: 78710873c2 ("net/ngbe: add HW initialization")
Cc: stable@dpdk.org
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Add check operation for vf function level reset,
mailbox messages and ack from vf.
Waiting to process the messages.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Add MAC addresses to filter incoming packets, support to set
multicast addresses to filter. And support to set unicast table array.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Since meson 0.59.0 version, the extract_all_objects() API
need to pass explicit boolean value.
To remove the following warning[1], added explicit `true` for
extract_all_objects() use in codebase whever there is
no argument.
[1]
WARNING: extract_all_objects called without setting recursive
keyword argument. Meson currently defaults to
non-recursive to maintain backward compatibility but
the default will be changed in the future.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Setup MSI-X interrupt, complete PHY configuration and set device link
speed to start device. Disable interrupt, stop hardware and clear queues
to stop device.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Add basic init and uninit function.
Map device IDs and subsystem IDs to single ID for easy operation.
Then initialize the shared code.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
