When user reissues same flow director cmd with a different queue
update the existing filter to redirect flow to the new desired
queue as destination just like the other filters like 5 tuple and
generic flow.
Fixes: 2d64da097a ("net/bnxt: support FDIR")
Cc: stable@dpdk.org
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
When the vnic_tpa_cfg HWRM command is sent to the FW,
we are not passing the VNIC ID in case of disable.
This can cause the FW to return an error.
Correct VNIC ID needs to be passed for both enable and disable.
Fixes: 0958d8b643 ("net/bnxt: support LRO")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The hw flags are not read correctly: the defines
RX_PKT_CMPL_FLAGS_ITYPE_* are not bits but values, so the should not be
tested with if (value & X) but with if ((value & MASK) == X).
This was resulting in a wrong packet type.
For instance, an IPv4/ICMP packet was returning a value of 7 for
the layer 4, which is undefined.
This patch rework the way packet types are processed, to ensure
that only valid packet types will be advertised.
Fixes: 3d2a6644eb ("net/bnxt: support getting ptypes")
Cc: stable@dpdk.org
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
There is no need to return an error if an existing MAC is added.
Fixes: 778b759ba1 ("net/bnxt: add MAC address")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are not parsing for 100G speed correctly.
With this patch we should be able to configure 100G link.
Fixes: 90ed2b7229 ("net/bnxt: add 100G speed detection")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
When Autoneg is turned off especially on remote side,
link does not come up. This patch fixes that.
Fixes: 7bc8e9a227 ("net/bnxt: support async link notification")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Fix the Rx offload flags when the IP or L4 checksum is seen as incorrect
by the hardware. In this case, the proper value is PKT_RX_IP_CKSUM_BAD.
PKT_RX_IP_CKSUM_NONE means that the checksum may be incorrect in the
packet headers, but the integrity of the IP header is verified. This is
mostly useful for virtual drivers.
Fixes: 7ec39d8c52 ("net/bnxt: update status of Rx IP/L4 CKSUM")
Cc: stable@dpdk.org
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The timestamp flag needs to be set in the offload flags
for the received pkt in case of PTP offload.
Fixes: b11cceb83a ("net/bnxt: support timesync")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
While using RSS, the pool count should be 1.
Fixes: 8103a57ab4 ("net/bnxt: handle Rx multi queue creation properly")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
When the driver is loaded on a 100G NIC, the port speed is not
displayed correctly. Parse the 100G speed before displaying it.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Currently this is implemented entirely in the PMD as there is no
explicit support in the HW. Re-program the RSS Table without this queue
on stop and add it back to the table on start.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
In certain cases the MAC address of a port could be all zeros.
Catch it early, log a message and fail the initialization.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Register for async events from the FW.
New events we are registering for include Link speed config changes,
PF driver unload and VF config change. Also log a message when the
async event arrives on the completion ring.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch implements driver specific log type doing away with
usage of RTE_LOG() for logging.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
During Tx ring allocation, the actual ring size configured in the HW
ends up being twice the number of txd parameter specified to the driver.
The power of 2 ring size wrongly adds a +1 while sending the ring
create command to the FW.
Fixes: 6eb3cc2294 ("net/bnxt: add initial Tx code")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Create a rte_ethdev_driver.h file and move PMD specific APIs here.
Drivers updated to include this new header file.
There is no update in header content and since ethdev.h included by
ethdev_driver.h, nothing changed from driver point of view, only
logically grouping of APIs. From applications point of view they can't
access to driver specific APIs anymore and they shouldn't.
More PMD specific data structures still remain in ethdev.h because of
inline functions in header use them. Those will be handled separately.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
The pointer to the user parameter of the callback registration is
automatically pass to the callback function.
There is no point to allow changing this user parameter by a caller.
That's why this parameter is always set to NULL by PMDs and set only
in ethdev layer before calling the callback function.
The history is that the user parameter was initially used
by the callback implementation to pass some information
between the application and the driver:
c1ceaf3ad0 ("ethdev: add an argument to internal callback function")
Then a new parameter has been added to leave the user parameter
to its standard usage of context given at registration:
d6af1a13d7 ("ethdev: add return values to callback process API")
The NULL parameter in the internal callback processing function
is now removed. It makes clear that the callback parameter is user
managed and opaque from a DPDK point of view.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
When allocating a new mbuf for Rx, the value of m->data_off should not
be reset to its default value (RTE_PKTMBUF_HEADROOM), instead of reusing
the previous undefined value, which could cause the packet to have a too
small or too high headroom.
Fixes: 2eb53b134a ("net/bnxt: add initial Rx code")
Cc: stable@dpdk.org
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Replace internal functions to get DMA address them with their generic
IOVA version. Also rename the 'data' variable to 'mbuf' for more
readability.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Check for availability of on-chip resources - like Queue count,
number stat context, number of ring groups before inheriting and
initializing as per application requirements.
Also check before creating a Tx or Rx queue make sure there are
enough resources to complete the request.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
bnxt_free_all_hwrm_rings() was freeing all the Rx Rings including
zero-ing out the memory for the Aggregation rings, but was not issuing
the FW cmd to destroy the AGG ring(s) from HW. This would manifest in
problems when port stop/port start would be issued as there would be a
HW ring leak every time port stop was issued.
Fixes: daef48efe5 ("net/bnxt: support set MTU")
Cc: stable@dpdk.org
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
When user re-issues same 5 tuple filter pattern cmd with different
destination queue, it would flag it as an existing match.
However, when deletion on this filter was attempted, it would crash
as the 'vnic' from which the filter was being removed from would be
different. Fix by updating the filter in the scenario where there
is a pattern match and only the destination queue varies.
Fixes: b7435d660a ("net/bnxt: add ntuple filtering support")
Cc: stable@dpdk.org
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
If the attribute/pattern for a flow is the same, with only the 'action'
i.e the destination queue index changing, allow it by cleaning up
the older ntuple filter and updating the existing flow with
the new filter rule having the new destination queue ID.
Also, clear the L2 filter during flow_destroy after destroying
the ntuple filter, otherwise the flow record is not completely purged
from the HW.
Fixes: 5ef3b79fdf ("net/bnxt: support flow filter ops")
Cc: stable@dpdk.org
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
filter1 which is used to just get the l2 filter FW id and not used
later was unnecessarily being inserted into a list and was not being
freed after it's use was done.
Fix it by not doing the list insertion and releasing it back to the free
filter pool.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
As per documentation, While supporting ethertype_filters matching
ether_types 0x0800 (IPv4) and 0x86DD (IPv6) is invalid.
But we were wrongly doing that. This patch fixes it.
Fixes: 5ef3b79fdf ("net/bnxt: support flow filter ops")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Maintain state of PMD initialization and check it before checking stats.
In certain cases, we might end up accessing stats before the required
HWRM commands are processed by FW.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Certain SKUs of NIC can support features like NPAR, Multi Host PFs per
port. We need to check for such features in order to restrict certain
HWRM commands from being sent to the FW.
For the single PF per port model, allow commands like hwrm_port_phy_cfg
from the PF driver. In NPAR and MH environments with multiple PFs per
port, we should not allow HWRM commands like hwrm_port_phy_cfg to be
sent to the FW.
This patch takes care of that.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
If the FW fails bnxt_hwrm_func_reset() with an error status,
instead of returning -1, return a more standard value of -EIO.
Similarly sometimes the status returned by certain FW commands
may not be generic. Return a more standard value of -EIO in
that case as well.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Ring groups is a Rx only attribute. Make sure there are sufficient
ring groups available. Return an error if they are not available.
Fixes: 37d6161a68 ("net/bnxt: add ring group alloc/free")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Parse the Tx checksum offload flags and set the proper bits
in the Tx descriptor.
Fixes: 6eb3cc2294 ("net/bnxt: add initial Tx code")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are incrementing idx twice while allocating Tx rings.
Since this is passed to the firmware, it may cause unexpected behavior.
Fixes: daef48efe5 ("net/bnxt: support set MTU")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are not checking for return values of functions like
bnxt_hwrm_queue_qportcfg and bnxt_hwrm_func_qcfg in bnxt_dev_init
thereby preventing a cleanup in case of a HWRM command failure.
This patch fixes that.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Implemented the 'time_sync' related APIs for supporting the PTP
protocol.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Repeated occurrences of 'the'.
The change was obtained using the following command:
sed -i "s;the the ;the ;" `git grep -l "the "`
Signed-off-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Remove a case where we were sending a deprecated field to the FW.
There is no need to send auto_link_speed to the FW.
Also set the auto_mode correctly depending on the setting requested.
Fixes: 7bc8e9a227 ("net/bnxt: support async link notification")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are not programming the vlan_spoof setting currently owing to
an unnecessary check. This patch fixes that.
Fixes: 36735a932c ("net/bnxt: support set VF QOS and MAC anti spoof")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
In some cases when a VF driver is unloaded after the PF driver,
certain HWRM commands are returned with an error.
Instead the PF can tell the FW to permit these commands in order
to allow a clean unload.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Set the filter_type before we match a new filter against existing
filters. Otherwise we are missing the existing filters.
Fixes: 2d64da097a ("net/bnxt: support FDIR")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are wrongly "OR-ing" the vnic->hash_type instead of assigning
the new hash type thereby wrongly configuring hash settings.
Fixing it.
Fixes: fcc0aa1edc ("net/bnxt: add RSS hash configuration")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Renamed data type from phys_addr_t to rte_iova_t.
Signed-off-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Rename buf_physaddr to buf_iova.
Keep the deprecated name in an anonymous union to avoid breaking
the API.
Signed-off-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
The struct rte_memzone field .phys_addr is renamed to .iova.
The deprecated name is kept in an anonymous union to avoid breaking
the API.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
The function rte_mem_virt2phy() is kept and used in functions which
works only with physical addresses.
For all other calls this function is replaced by rte_mem_virt2iova()
which does a direct mapping (no conversion) in the VA case.
Note: the new function rte_mem_virt2iova() function matches the
behaviour implemented in rte_mem_virt2phy() by the commit
680f6c1260 ("mem: honor IOVA mode in virt2phy")
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
The PCI lib defines the types and methods allowing to use PCI elements.
The PCI bus implements a bus driver for PCI devices by constructing
rte_bus elements using the PCI lib.
Move the relevant code out of the EAL to its expected place.
Libraries, drivers, unit tests and applications are updated to use the
new rte_bus_pci.h header when necessary.
Signed-off-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Some devices may not support or fail setting VLAN offload
configuration based on dynamic circumstances so the
vlan_offload_set_t vector is modified to return an int so
the caller can determine success or not.
rte_eth_dev_set_vlan_offload is updated to return the
value provided by the vector when called along with restoring
the original offload configs on failure.
Existing vlan_offload_set_t vectors are modified to return
an int. Majority of cases return 0 but a few that actually
can fail now return their failure codes.
Finally, a vlan_offload_set_t vector is added to virtio
to facilitate dynamically turning VLAN strip on or off.
Signed-off-by: David Harton <dharton@cisco.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
PKT_RX_VLAN_PKT and PKT_RX_QINQ_PKT are deprecated for a while.
As explained in [1], these flags were kept to let the applications and
PMDs move to the new flag. There is also a need to support Rx vlan
offload without vlan strip (at least for the ixgbe driver).
This patch renames the old flags for this feature, knowing that some
PMDs were using PKT_RX_VLAN_PKT and PKT_RX_QINQ_PKT to indicate that
the vlan tci has been saved in the mbuf structure.
It is likely that some PMDs do not set the proper flags when doing vlan
offload, and it would be worth making a pass on all of them.
Link: [1] http://dpdk.org/ml/archives/dev/2017-June/067712.html
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This flag is not necessary at the ether layer anymore.
Buses are able to advertise their hotplug support. The ether layer can
rely upon this capability instead of a special flag.
Signed-off-by: Gaetan Rivet <gaetan.rivet@6wind.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Fixes: 75cd6fb1d9 ("net/bnxt: fix the association of a MACVLAN per VNIC")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
return value stored in "rc" but it has been overwritten before use.
Coverity issue: 147216
Fixes: 7a5b087444 ("net/bnxt: support to add a VF MAC address")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are left shifting more bits than we should be doing.
This patch fixes that.
Coverity issue: 127546
Fixes: 778b759ba1 ("net/bnxt: add MAC address")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The case to handle redirect a flow to a VF is not handled.
This patch fixes it.
Fixes: 5ef3b79fdf ("net/bnxt: support flow filter ops")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch removes some redundant code from bnxt_mq_rx_configure().
Fixes: 75cd6fb1d9 ("net/bnxt: fix the association of a MACVLAN per VNIC")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch simplifies logic for RSS queue creation.
1) Do not hardcode number of VNIC pools in case of RSS
2) Log a message if Number of queues is > RTE_ETHDEV_QUEUE_STAT_CNTRS
3) Move the check for allocation of l2_filter inside the for loop.
Fixes: 6133f20797 ("net/bnxt: add Rx queue create/destroy")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are not setting the rx_offload capabilities. Fixing that.
Fixes: 0a6d2a7200 ("net/bnxt: get device infos")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are not indicating VLAN insert capability of HW. Fixing it.
Fixes: 0a6d2a7200 ("net/bnxt: get device infos")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The list of libraries in LDLIBS was generated from the DEPDIRS-xyz
variable. This is valid when the subdirectory name match the library
name, but it's not always the case, especially for PMDs.
The patches removes this feature and explicitly adds the proper
libraries in LDLIBS.
Some DEPDIRS-xyz variables become useless, remove them.
Reported-by: Gage Eads <gage.eads@intel.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
The stats_get dev op API doesn't include return value, so PMD cannot
return an error in case of failure at stats getting process time.
Since PCI devices can be removed and there is a time between the
physical removal to the RMV interrupt, the user may get invalid stats
without any indication.
This patch changes the stats_get API return value to be int instead of
void.
All the net PMDs stats_get dev ops are adjusted by this patch.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
We were not associating a MAC+VLAN per VNIC filter correctly.
This patch fixes that. Also set the VLAN type appropriately.
Fixes: f92735db1e ("net/bnxt: add L2 filter alloc/init/free")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Match a flow against existing flows programmed in the HW
and prevent overlapping entries. Also change log level of
some logs to DEBUG.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are not checking if a filter allocation succeeded.
And we end up accessing a null pointer after that.
Also invalidate the fw_l2_filter_id to prevent unnecessary
HW access and hence HWRM command failures during exit.
Fixes: 5ef3b79fdf ("net/bnxt: support flow filter ops")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
For gcc (GCC) 4.8.3 20140911 (Red Hat 4.8.3-7),
As of 5ef3b79fdf, compilation of DPDK fails with the following
ERROR MESSAGE:
"bnxt_filter.c:960:117: error: ‘vnic’ may be used uninitialized in this
function [-Werror=maybe-uninitialized]".
Resolve this by initializing 'vnic' to NULL;
Fixes: 5ef3b79fdf ("net/bnxt: support flow filter ops")
Signed-off-by: Mark Kavanagh <mark.b.kavanagh@intel.com>
Extend port_id definition from uint8_t to uint16_t in lib and drivers
data structures, specifically rte_eth_dev_data. Modify the APIs,
drivers and app using port_id at the same time.
Fix some checkpatch issues from the original code and remove some
unnecessary cast operations.
release_17_11 and deprecation docs have been updated in this patch.
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The compilation with gcc-6.3.0 and EXTRA_CFLAGS=-Og gives the following
error:
CC rte_pmd_bnxt.o
rte_pmd_bnxt.c: In function ‘rte_pmd_bnxt_set_all_queues_drop_en’:
rte_pmd_bnxt.c:116:6: error: ‘rc’ may be used uninitialized in this
function [-Werror=maybe-uninitialized]
int rc;
^~
This can happen if both bp->nr_vnics and bp->pf.active_vfs are 0.
Fix it by initializing rc to -EINVAL.
Fixes: 49947a13ba ("net/bnxt: support Tx loopback, set VF MAC and queues drop")
Cc: stable@dpdk.org
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
We were hardcoding the max MAC addresses to 32, while the HW
can support more than that. This was restricting the number of VMDQ
pools that we could support. Use the value obtained from FW instead.
Fixes: 804e746c7b ("net/bnxt: add hardware resource manager init code")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add support for ntuple filtering.
Only RTE_5TUPLE_FLAGS is supported currently.
RTE_2TUPLE_FLAGS is not supported.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add support for get/set_eeprom, get_eeprom_length dev_ops.
Defined the structures required to get/set the eeprom length/data
in hsi_struct_defs hdr file along with implementation.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
In some cases the interrupt handler is accessing cpr, which has
already been freed causing segfaults. This patch avoids such accesses.
Fixes: 7bc8e9a227 ("net/bnxt: support async link notification")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
While gathering per queue stats, we are overwriting some of the
stats. This causes some of the counters in xstats to be incorrect.
Fixes: 577d3dced0 ("net/bnxt: refactor the query stats")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We were not setting the dev_info.hash_key_size. Setting it now.
Fixes: 0a6d2a7200 ("net/bnxt: get device infos")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are not configuring the RSS settings updated by rss_hash_update().
Fixing it.
Fixes: fcc0aa1edc ("net/bnxt: add RSS hash configuration")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
update ol_flags with the appropriate status of IP/L4 cksum in Rx path.
Fixes: 2eb53b134a ("net/bnxt: add initial Rx code")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are not correctly setting hw checksum offload for all the
offload flags. This patch fixes that.
Fixes: 6eb3cc2294 ("net/bnxt: add initial Tx code")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Map ETH_VMDQ_ACCEPT_HASH_UC to the promiscuous bit.
Also, set ALLMULTI and MCAST when MCAST is set to ensure multicast traffic
is received regardless of the VF driver list.
Fixes: 4cfe399f65 ("net/bnxt: support to set VF rxmode")
Cc: stable@dpdk.org
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
In bnxt_hwrm_cfa_l2_set_rx_mask, we are ignoring the previous
setting of HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_BCAST and
setting it again, thereby wrongly enabling Broadcast.
Fixes: 244bc98b0d ("net/bnxt: set L2 Rx mask")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Even when rx buffer allocation fails, we are wrongly updating
the producer index. This patch fixes that.
Also in case of a buffer allocation failure, reattempt buffer
allocation before the rx handler exits.
Fixes: 2eb53b134a ("net/bnxt: add initial Rx code")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are currently not handling multi queue RX/RSS modes correctly.
If RSS is not requested, create one VNIC per RXQ.
Fixes: 6133f20797 ("net/bnxt: add Rx queue create/destroy")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The calculation for number of pools is wrong.
We are wrongly overwriting the calculated value with ETH_64_POOLS.
Accordingly fix the size of ff_pools array.
Fix the log message as well.
Fixes: 4cfe399f65 ("net/bnxt: support to set VF rxmode")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
start_grp_id is incremented wrongly. Fixing it.
Fixes: daef48efe5 ("net/bnxt: support set MTU")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are wrongly using just 16 bits of address from rte_mem_virt2phy
while filling the vlan table address instead of 64-bytes.
Most likely a copy-paste error.
Fixes: 36735a932c ("net/bnxt: support set VF QOS and MAC anti spoof")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Obtain the spinlock in HWRM_PREP()
Eliminate two unnecessary arguments in HWRM_PREP().
Unlock the spinlock before returning in HWRM_ERROR_CHECK()
Add new HWRM_UNLOCK() macro
Update usage of the thre macros.
Fixes: 804e746c7b ("net/bnxt: add hardware resource manager init code")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
The callback arguments to _rte_eth_dev_callback_process() are swapped.
Fix them.
Fixes: d6af1a13d7 ("ethdev: add return values to callback process API")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Only set the vlanonly bit if vlan_nonvlan is clear. Also, allow the
VLAN table to be cleared when vlanonly is set.
Clearing the VLAN table when vlanonly is set will stop all traffic
since it requires all frames to have a VLAN tag, and that tag to be
in the zero-length table. This is still a valid use case though,
and has been seen in the wild.
Fixes: 36735a932c ("net/bnxt: support set VF QOS and MAC anti spoof")
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
If the current VLAN anti spoof setting is same as the new value,
the firmware can return an error. Call the HWRM command to update
the new setting if it is different from the current value.
Fixes: 36735a932c ("net/bnxt: support set VF QOS and MAC anti spoof")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch sends the HWRM command to free a filter in the hardware,
before using it again.
Fixes: f92735db1e ("net/bnxt: add L2 filter alloc/init/free")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are wrongly using a Rx side HWRM command set_rx_mask to configure
VLAN anti-spoof. This being a Tx side feature, this patch
tries to fix it.
Since the HWRM command to do it is available only in
the newer firmware versions, the patch verifies the firmware
version before attempting to send the HWRM command to
the firmware.
Fixes: 36735a932c ("net/bnxt: support set VF QOS and MAC anti spoof")
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch resets the VF stats during initialization
Fixes: b7778e8a1c ("net/bnxt: refactor to properly allocate resources for PF/VF")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
remove the unnecessary rte_delay in bnxt_set_hwrm_link_config
Fixes: 7bc8e9a227 ("net/bnxt: support async link notification")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Check if the vnic_id and rss_rule is not invalid before passing it
to the firmware to cleanup the VNIC. Log a message if the vnic_id
is invalid.
Fixes: db678d5c2b ("net/bnxt: add HWRM VNIC configure")
Cc: stable@dpdk.org
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Fix use of local variable to avoid segfault.
cnt was incorrectly tested and decremented in the loop that removes
a VLAN from the table.
Fixes: 36735a932c ("net/bnxt: support set VF QOS and MAC anti spoof")
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
1) handle_async_event is a DEBUG level log message.
2) Log "Unable to get default VNIC for VF %d" at INFO level.
Fixes: 36735a932c ("net/bnxt: support set VF QOS and MAC anti spoof")
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Fix an error message. Probably a copy/paste error.
Fixes: 36735a932c ("net/bnxt: support set VF QOS and MAC anti spoof")
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
bnxt_hwrm_port_phy_cfg() was not setting enables appropriately.
This was causing undesired issues with link config.
This patch takes care of that.
Fixes: 7bc8e9a227 ("net/bnxt: support async link notification")
Cc: stable@dpdk.org
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We are not passing proper speed mask causing autoneg to not work
properly on 10GBase-T links. Use supported speeds from phy_qcfg
for auto mask to fix this.
Fixes: 7bc8e9a227 ("net/bnxt: support async link notification")
Cc: stable@dpdk.org
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch fixes the get link configuration code.
bnxt_get_hwrm_link_config was using wrong macros and wrongly
deriving link speed based on link status which was causing
incorrect link information to be displayed in few scenarios.
Fixes: 7bc8e9a227 ("net/bnxt: support async link notification")
Cc: stable@dpdk.org
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add code to avoid automatic clearing of VF stats on a function
reset or a stat context free.
Add rte_pmd_bnxt_set_vf_persist_stats() PMD specific API.
Fixes: dd46c6bbd5 ("net/bnxt: support get and clear VF specific stats")
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Previously, no VNICs were allocated as the default VNIC,
even if they were configured as one. This patch fixes that error.
Fixes: db678d5c2b ("net/bnxt: add HWRM VNIC configure")
Cc: stable@dpdk.org
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
We used the default as a work-around for the 4-byte MTU VNICs,
but we filter those out now. So fix the calculation of VNICs
accordingly.
Fixes: ff63ebbb67 ("net/bnxt: determine the Rx status of VF")
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Set the MTU of the device to MAX size possible.
Fixes: b7778e8a1c ("net/bnxt: refactor to properly allocate resources for PF/VF")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds support for Stratus VF devices.
Other than adding the VF device ID, we also are adding
support for short message format.
The new short firmware message of size 16 bytes points to a location
in host memory that contains the firmware message that the driver
wants the adapter to process. This indirection requires the
firmware to DMA the message into its own memory for processing.
When the firmware receives a Short Command Format, it will DMA the
firmware message from host memory into its internal memory and then
processes the message as it would have if it received the message
directly in the firmware communication channel.
With BCM57454, the number of VFs increase to 1K and so the requirement
for firmware communication channel memory on adapter becomes expensive.
The short firmware message saves the amount of memory required to support
1K VFs on adapter.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Device name resides in two different locations, in rte_device->name and
in ethernet device private data.
For now, the copy in the ethernet device private data is required for
multi process support, the name is the how secondary process finds about
primary process device.
But for drivers there is no reason to use the copy in the ethernet
device private data.
This patch updates PMDs to use only rte_device->name.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Change the rte_eth_dev_callback_process function to return int,
and add a void *ret_param parameter.
The new parameter is used by ixgbe and i40e instead of abusing
the user data of the callback.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
rte_driver->name has the driver name and all physical and virtual
devices has access to it.
Previously it was not possible for virtual ethernet devices to access
rte_driver->name field (because eth_dev used to keep only pci_dev),
and it was required to save driver name in the device private struct.
After re-works on bus and vdev, it is possible for all bus types to
access rte_driver.
It is able to remove the driver name from ethdev device private data and
use eth_dev->device->driver->name.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Jan Blunck <jblunck@infradead.org>
This patch fixes incorrect reporting of link status
1) When link is down, set speed to zero. Otherwise a wrong non-zero
speed will be displayed.
2) DAC cables can detect there is a signal, but it necessarily does not
mean link is up. Code previously treated this as link up.
Fixes: 7bc8e9a227 ("net/bnxt: support async link notification")
Cc: stable@dpdk.org
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Some HWRM defines are missing from hsi_struct_def_dpdk.h
This patch adds them.
Also remove duplicate HWRM_RING_GRP_ALLOC entry.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds support to configure the VF L2 Rx settings.
The per VF setting is maintained in bnxt_child_vf_info.l2_rx_mask
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds code to insert a default VF VLAN.
Also track the current default VLAN per vnic for the VF.
When setting the default VLAN, avoid setting it to the current value.
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds support to allocate a filter and program
it in the hardware for every MAC address added to the specified
function.
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds code to determine the Rx status of a VF.
It adds the rte_pmd_bnxt_get_vf_rx_status call, which calculates
the VNIC count of the function to get the Rx status.
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds code to get and clear VF stats.
It also adds the necessary HWRM structures to send the command
to the firmware.
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds support to
1) enable VF MAC anti spoof.
2) QOS configuration for specified VF.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add functions rte_pmd_bnxt_set_tx_loopback,
rte_pmd_bnxt_set_all_queues_drop_en and
rte_pmd_bnxt_set_vf_mac_addr to configure tx_loopback,
queue_drop and VF MAC address setting in the hardware.
It also adds the necessary functions to send the HWRM commands
to the firmware.
Signed-off-by: Steeven Li <steeven.li@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
1) Use hwrm_stat_ctx_query command to query statistics
Using hwrm_stat_ctx_query command will allow polling
the statistics from hardware instead of using the current push
model from the hardware which does a DMA of the stats to the host
at fixed intervals.
2) Use the rx_mbuf_alloc_fail to track mbuf alloc failures.
3) We were wrongly incrementing hwrm_cmd_seq in bnxt_hwrm_stat_clear
and bnxt_hwrm_stat_ctx_alloc functions. This patch fixes that.
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds support to enable and disable LRO
To support this feature, the driver creates an aggregator ring.
When the hardware starts doing LRO, it sends a tpa_start completion.
When the driver receives a tpa_end completion, it indicates that the
LRO chaining is complete.
Signed-off-by: Steeven Li <steeven.li@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds support to modify MTU using the set_mtu dev_op.
To support frames > 2k, the PMD creates an aggregator ring.
When a frame greater than 2k is received, it is fragmented
and the resulting fragments are DMA'ed to the aggregator ring.
Now the driver can support jumbo frames upto 9500 bytes.
Signed-off-by: Steeven Li <steeven.li@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds VLAN strip and offload callbacks.
To add a VLAN filter:
For each VNIC and each associated filter(s)
if VLAN exists:
if VLAN matches vlan_id
VLAN filter already exists, just skip and continue
else
add a new MAC+VLAN filter
else
Remove the old MAC only filter
Add a new MAC+VLAN filter
To remove a VLAN filter:
For each VNIC and each associated filter(s)
if VLAN exists && VLAN matches vlan_id
remove the MAC+VLAN filter
add a new MAC only filter
else
VLAN filter doesn't exist, just skip and continue
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds support to get and reset xstats dev_ops
dev_ops added:
xstats_get, xstats_get_name, xstats_reset
HWRM commands added:
hwrm_port_qstats, hwrm_port_clr_stats
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add support for udp_tunnel_port_add/del dev_ops to configure a UDP port
for VXLAN and Geneve Tunnel protocols.
The HWRM supports only one global destination port for a tunnel type,
use a reference counter to keep track of its usage.
Cache the configured VXLAN/Geneve ports and use that value to check
if the right UDP port is being freed up.
Skip calling bnxt_hwrm_tunnel_dst_port_alloc if the same UDP port is
being programmed.
Skip calling bnxt_hwrm_tunnel_dst_port_free if no UDP port has been
configured.
Also update tx offload capabilities
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add the cmd_err and opaque_0 and opaque_1 fields to HWRM error
messages. These allow better debugging of some classes of HWRM
errors.
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
rte_malloc_virt2phy() does not return a physical address if huge pages
aren't in use. Further, rte_memzone->phys_addr is not a physical address.
Use rte_mem_virt2phy() and manually lock pages to support lack of
huge pages.
Also check the return value of rte_mem_virt2phy()
Verify the function returns an address. Otherwise return an error and
log a message.
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
1) For a VF, query the firmware to determine if a MAC address is
already configured. If not configure a random default MAC address.
2) Do not initialize the default completion ring in
bnxt_alloc_hwrm_rings().
3) While registering for async events with the firmware,
use func_vf_cfg for a VF and use func_cfg for a PF.
4) Query the VNIC plcmode config using the bnxt_hwrm_vnic_plcmodes_qcfg
before a VNIC is updated. Reconfigure the VNIC with the plcmode
configuration queried earlier. Not doing this could overwrite
the plcmodes in some cases.
5) Reorg the bnxt_handle_fwd_req to properly handle the forwarded
requests. The previous code did not handle it completely.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
1) Move the function reset to bnxt_dev_init.
On the same lines, setup, enable and request interrupt to init path.
Memory allocation is also being done in the init path.
2) After a function reset, configure the VFs. Distribute resources
evenly between all functions (PF and VF) for now. In the future, this
should be controllable.
3) The bnxt_vf_info and bnxt_pf_info had lot of duplication. Move the
common items to struct bnxt. And only unique items specific to PF
remain in the struct bnxt_pf_info.
4) Program the firmware to allow certain commands sent by a VF.
Disallowing these will prevent clean VF driver cleanup.
5) Since PF/VF need to allocate resources from a pool in the hardware,
use func_qcaps and func_qcfg to appropriately query the capabilities
and available resources.
6) If a PF is being initialized and no VFs are allocated, explicitly
call func_cfg to allocate the resources.
7) Once resources are requested from the firmware, update local copy
of resource count in struct bnxt only after sending the func_qcfg to
make sure the allocation request in the firmware went through.
The changes in this patch will be used by the subsequent patches
to allow proper initialization of PF/VF instance.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch updates the Broadcom bnxt PMD to version 1.7.7
Most of the changes in the patch are in the hsi_struct_def_dpdk.h - an
autogenerated file. The changes in the *.c files are because of changes
in the macro names.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Instead of many PMD define their own macro, define a generic one in
ethdev and use that in PMDs.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Allain Legacy <allain.legacy@windriver.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
remove __rte_unused instances that are not required.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Allain Legacy <allain.legacy@windriver.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
vfio is the kernel framework used by the vfio-pci kernel driver.
DPDK drivers do not rely solely on vfio, but rather on vfio-pci to gain
access to pci resources.
Fixes: 0880c40113 ("drivers: advertise kmod dependencies in pmdinfo")
Cc: stable@dpdk.org
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Some customers find adding MAC addr to VF sometimes can fail,
but it is still stored in dev->data->mac_addrs[ ]. So this
can lead to some errors that assumes the non-zero entry in
dev->data->mac_addrs[ ] is valid.
Following acknowledgements are from specific NIC PMD
maintainer for their managing part.
This patch changes the ethdev internal API, it should not be
backported to a stable/LTS release so far.
Fixes: af75078fec ("first public release")
Signed-off-by: Wei Dai <wei.dai@intel.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The patch change the prototype of callback function
(rte_intr_callback_fn) by removing the unnecessary parameter.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Before this patch, the management of dependencies between directories
had several issues:
- the generation of .depdirs, done at configuration is slow: it can take
more than one minute on some slow targets (usually ~10s on a standard
PC without -j).
- for instance, it is possible to express a dependency like:
- app/foo depends on lib/librte_foo
- and lib/librte_foo depends on app/bar
But this won't work because the directories are traversed with a
depth-first algorithm, so we have to choose between doing 'app' before
or after 'lib'.
- the script depdirs-rule.sh is too complex.
- we cannot use "make -d" for debug, because the output of make is used for
the generation of .depdirs.
This patch moves the DEPDIRS-* variables in the upper Makefile, making
the dependencies much easier to calculate. A DEPDIRS variable is still
used to process library dependencies in LDLIBS.
After this commit, "make config" is almost immediate.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Tested-by: Robin Jarry <robin.jarry@6wind.com>
Tested-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
dev_flags is wrongly overwritten with RTE_ETH_DEV_DETACHABLE value
in drivers after rte_eth_copy_pci_info().
Previous values of the dev_flags set in rte_eth_copy_pci_info(),
like RTE_ETH_DEV_INTR_LSC, are get lost. That will fail the device
configuration.
Fix by preventing dev_flags overwritten.
Fixes: 22dda618c0 ("pci: separate detaching ethernet ports from PCI devices")
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Replace the raw I/O device memory read/write access with eal abstraction
for I/O device memory read/write access to fix portability issues across
different architectures.
CC: Stephen Hurd <stephen.hurd@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Add support for PCI IDs which was removed as a part of
commit 0e7bd0b2d6 ("net/bnxt: remove support for few devices")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Attaching and detaching ethernet ports from an application
is not the same thing as physically removing a PCI device,
so clarify the flags indicating support. All PCI devices
are assumed to be physically removable, so no flag is
necessary in the PCI layer.
Signed-off-by: Ben Walker <benjamin.walker@intel.com>
This makes struct rte_eth_dev independent of struct rte_pci_device by
replacing it with a pointer to the generic struct rte_device.
Signed-off-by: Jan Blunck <jblunck@infradead.org>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Only the drivers itself can decide if it could fill PCI information fields
of dev_info.
Signed-off-by: Jan Blunck <jblunck@infradead.org>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Use existing information about pci and interrupt handle to minimize
the number of places that assume eth_dev contains pci_device
information.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jan Blunck <jblunck@infradead.org>
Add a new macro RTE_PMD_REGISTER_KMOD_DEP() that allows a driver to
declare the list of kernel modules required to run properly.
Today, most PCI drivers require uio/vfio.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Today, all logs whose level is lower than INFO are dropped at
compile-time. This prevents from enabling debug logs at runtime using
--log-level=8.
The rationale was to remove debug logs from the data path at
compile-time, avoiding a test at run-time.
This patch changes the behavior of RTE_LOG() to avoid the compile-time
optimization, and introduces the RTE_LOG_DP() macro that has the same
behavior than the previous RTE_LOG(), for the rare cases where debug
logs are in the data path.
So it is now possible to enable debug logs at run-time by just
specifying --log-level=8. Some drivers still have special compile-time
options to enable more debug log. Maintainers may consider to
remove/reduce them.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Some of the production parts will arrive after the 16.11 release.
Back off support for those devices. We will add these IDs again
at an appropriate time.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Prevent the arithmetic in bnxt_alloc_vnic_attributes from causing
any unintentional havoc because of the usage of a signed variable.
Coverity issue: 137874
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
All macros related to driver registeration renamed from DRIVER_*
to RTE_PMD_*
This includes:
DRIVER_REGISTER_PCI -> RTE_PMD_REGISTER_PCI
DRIVER_REGISTER_PCI_TABLE -> RTE_PMD_REGISTER_PCI_TABLE
DRIVER_REGISTER_VDEV -> RTE_PMD_REGISTER_VDEV
DRIVER_REGISTER_PARAM_STRING -> RTE_PMD_REGISTER_PARAM_STRING
DRIVER_EXPORT_* -> RTE_PMD_EXPORT_*
Fix PMDINFOGEN tool to look for matches of RTE_PMD_REGISTER_*.
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
This patch adds support to get Link notification asynchronously.
The HW sends async notifications on default completion ring. The
PMD processes these notifications and logs a message appropriately.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch fixes segfault encountered during dev_uninit/close routine.
KNI sample app can be used to reproduce the issue.
Fixes: c09f57b49c ("net/bnxt: add start/stop/link update operations")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Some(?) compilers will treat the unmarked constant 1 as a 32-bit
integer, but the shift operation is in a loop that could run up to
63 times -- undefined behavior!
Coverity issue: 127546
Fixes: 778b759ba1 ("net/bnxt: add MAC address")
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Otherwise, the inherent cast when multiplying entry_length by max_vnics
in the call to rte_memzone_reserve could promote max_vnics to a signed
value, causing hilarity to ensue...
Coverity issue: 127557
Fixes: 9738793f28 ("net/bnxt: add VNIC functions and structs")
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - a onetime change owing to the usage of a different auto generated
file.
Structures updated:
hwrm_stat_ctx_alloc_input, hwrm_stat_ctx_alloc_output,
hwrm_stat_ctx_free_input, hwrm_stat_ctx_free_output,
hwrm_stat_ctx_clr_stats_input, hwrm_stat_ctx_clr_stats_output,
hwrm_exec_fwd_resp_input, hwrm_exec_fwd_resp_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use packet filtering related structures as per the
1.5.1 version of the HWRM API. Most of the changes in the patch are
white spaces and rearrangement of the lines - a onetime change owing to
the usage of a different auto generated file.
Structures being updated:
hwrm_cfa_l2_filter_cfg_input, hwrm_cfa_l2_filter_cfg_output,
hwrm_cfa_l2_set_rx_mask_input, hwrm_cfa_l2_set_rx_mask_output,
hwrm_cfa_l2_filter_alloc_input, hwrm_cfa_l2_filter_alloc_output,
hwrm_cfa_l2_filter_free_input, hwrm_cfa_l2_filter_free_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use HWRM ring related structures as per the 1.5.1
version of the HWRM API. Most of the changes in the patch are white
spaces and rearrangement of the lines - a onetime change owing to the
usage of a different auto generated file.
Structures being updated:
hwrm_ring_alloc_input, hwrm_ring_alloc_output, hwrm_ring_free_input,
hwrm_ring_free_output, hwrm_ring_grp_alloc_input,
hwrm_ring_grp_alloc_output, hwrm_ring_grp_free_input,
hwrm_ring_grp_free_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use VNIC related structures as per the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - a onetime change owing to the usage of a different
auto generated file.
Structures being updated:
hwrm_vnic_alloc_input, hwrm_vnic_alloc_output, hwrm_vnic_free_input,
hwrm_vnic_free_output, hwrm_vnic_cfg_input, hwrm_vnic_cfg_output,
hwrm_vnic_rss_cfg_input, hwrm_vnic_rss_cfg_output,
hwrm_vnic_rss_cos_lb_ctx_alloc_input,
hwrm_vnic_rss_cos_lb_ctx_alloc_output,
hwrm_vnic_rss_cos_lb_ctx_free_input,
hwrm_vnic_rss_cos_lb_ctx_free_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - a onetime change owing to the usage of a different
auto generated file.
Structures updated:
hwrm_func_qcfg_input, hwrm_func_qcfg_output, hwrm_func_drv_rgtr_input,
hwrm_func_drv_rgtr_output, hwrm_func_drv_unrgtr_input,
hwrm_func_drv_unrgtr_output, hwrm_queue_qportcfg_input,
hwrm_queue_qportcfg_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - a onetime change owing to the usage of a different
auto generated file.
Structures being updated in this patch:
input, output, hwrm_ver_get_input, hwrm_ver_get_output,
hwrm_func_reset_input, hwrm_func_reset_output, hwrm_func_qcaps_input,
hwrm_func_qcaps_output
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use structures as per the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - hopefully a onetime change owing to the usage of a different
auto generated file.
Structures updated:
cmpl_base, tx_cmpl, rx_pkt_cmpl, rx_pkt_cmpl_hi, hwrm_fwd_req_cmpl,
hwrm_async_event_cmpl
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use the 1.5.1 HWRM API.
Most of the changes in the patch are white spaces and rearrangement of the
lines - hopefully a onetime change owing to the usage of a different
auto generated file.
Structures updated in this patch:
tx_bd_short, tx_bd_long, tx_bd_long_hi, rx_prod_pkt_bd
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the PMD to use the 1.5.1 HWRM API.
Most of the changes in this patch and the following patches are
white spaces and rearrangement of the lines - hopefully a onetime change
owing to the usage of a different auto generated file.
Other than that, the following fields have been renamed:
1) rx_err_pkts and tx_err_pkts are now rx_discard_pkts and tx_discard_pkts
in struct ctx_hw_stats64
2) the perm_mac_addr field in the response of bnxt_hwrm_func_qcaps has
changed to mac_addr.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add support to the bnxt PMD to load on a PCI VF.
1) VF cannot change parameters like - speed, autoneg and pause
2) If the VF MAC address shows up as all 0's it has to be provisioned
by the PF in the hypervisor.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
More PCI Device IDs for Cumulus, Cumulus+ and Whitney, Whitney+ SKUs.
The NPAR model supported by firmware has been altered. It now allocates a
unique Device ID for each NPAR partition for each device. In addition,
ASIC's that are capable of supporting dual media have a unique DID
depending whether they are configured in copper or fiber mode.
This patch adds the necessary DIDs.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Adding code to enable support for NIC Partitioning or NPAR 1.0
As a part of NPAR, we don't allow port settings like speed or flow
control to be changed.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch adds support for the Broadcom StrataGX® BCM5871X
series of Communications Processors.
These ARM based processors target a broad range of networking
applications including virtual CPE (vCPE) and NFV appliances,
10G service routers and gateways, control plane processing for
Ethernet switches, and network attached storage (NAS).
Other than adding the PCI Id for supporting the device,
the patch also adds a memory barrier before the Tx doorbell
and Completing ring doorbell is written to. Since ARM has a
weakly ordered memory model this enforces a strict ordering
of the descriptor writes before the doorbell writes happen.
Signed-off-by: John Carney <john.carney@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Remove the 'name' member from rte_pci_driver and move to generic
rte_driver.
Most of the PMD drivers were initially using DRIVER_REGISTER_PCI(<name>..)
as well as assigning a name to eth_driver.pci_drv.name member.
In this patch, only the original DRIVER_REGISTER_PCI(<name>..) name has
been populated into the rte_driver.name member - assignments through
eth_driver has been removed.
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
[Shreyansh: Rebase and expand changes to newly added files]
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: David Marchand <david.marchand@6wind.com>
Simplify crypto and ethdev pci drivers init by using newly introduced
init macros and helpers.
Those drivers then don't need to register as "rte_driver"s anymore.
Exceptions:
- virtio and mlx* use RTE_INIT directly as they have custom initialization
steps.
- VDEV devices are not modified - they continue to use PMD_REGISTER_DRIVER.
Update documentation for replacing an example referring to
PMD_REGISTER_DRIVER.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
As discussed in the past release, driver names are modified
to be more consistent, and the future driver should follow
this new convention.
Driver names consist of:
"driver category"_"driver folder name"_"optional extra name".
For example:
- Crypto null driver -> "crypto_null"
- Network IXGBE VF driver -> "net_ixgbe_vf"
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Moved defines since the driver had no such information.
Used RTE_PCI_DEVICE in place of RTE_PCI_DEV_ID_DECL* stuff.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Currently we are wrongly setting HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_MCAST
flag in bnxt_hwrm_cfa_l2_set_rx_mask() which is preventing promiscuous
and multicast promiscuous settings from working correctly.
This patch fixes it.
Fixes: 244bc98b0d ("net/bnxt: set L2 Rx mask")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Since now the PMD_REGISTER_DRIVER macro sets the driver names,
there is no need to have the rte_driver structure setting it
statically, as it will get overridden.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Modify the PMD_REGISTER_DRIVER macro, adding a name argument to it. The
addition of a name argument creates a token that can be used for subsequent
macros in the creation of unique symbol names to export additional bits of
information for use by the pmdinfogen tool. For example:
PMD_REGISTER_DRIVER(ena_driver, ena);
registers the ena_driver struct as it always did, and creates a symbol
const char this_pmd_name0[] __attribute__((used)) = "ena";
which pmdinfogen can search for and extract. The subsequent macro
DRIVER_REGISTER_PCI_TABLE(ena, ena_pci_id_map);
creates a symbol const char ena_pci_tbl_export[] __attribute__((used)) =
"ena_pci_id_map";
Which allows pmdinfogen to find the pci table of this driver
Using this pattern, we can export arbitrary bits of information.
pmdinfo uses this information to extract hardware support from an object
file and create a json string to make hardware support info discoverable
later.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Panu Matilainen <pmatilai@redhat.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Add flow_ctrl_get and flow_ctrl_set dev_ops.
Uses the bnxt_set_hwrm_link_config() HWRM API added in earlier patch.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add rss_hash_update and rss_hash_conf_get dev_ops
Uses the bnxt_hwrm_vnic_rss_cfg() HWRM API added in the previous patch.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add code to Update/query reta dev_ops
Uses the bnxt_hwrm_vnic_rss_cfg() HWRM API added earlier.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Adds dev_ops to set link Up or Down as appropriate.
Uses the bnxt_set_hwrm_link_config() API added previously.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch adds dev_ops to Add/Remove MAC addresses.
These use the bnxt_hwrm_set_filter() defined previously
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch adds code to free all resources except the one corresponding
to HWRM, which are required to notify the HWRM that the driver is unloaded
(these are freed in uninit()).
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch adds dev_ops to enable/disable multicast traffic.
Uses the bnxt_hwrm_cfa_l2_set_rx_mask() API added earlier.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch adds the promiscuous mode enable and disable dev_ops.
Uses the bnxt_hwrm_cfa_l2_set_rx_mask() API added in an earlier commit.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch adds code to add the start, stop and link update dev_ops.
Also adds wrapper functions like bnxt_init_chip(), bnxt_init_nic(),
bnxt_alloc_mem(), bnxt_free_mem()
The BNXT driver will now minimally pass traffic with testpmd.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add HWRM calls to query the port's PHY and link configuration.
New HWRM call:
bnxt_hwrm_port_phy_qcfg
This command queries the PHY configuration for the port
Also adding helper function like bnxt_get_hwrm_link_config()
and bnxt_parse_hw_link_speed() parse the link state.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add a top level functions to initialize ring groups, and functions
to allocate and free all the rings via HWRM.
A ring group is identified by an index. It consists of Rx or Tx ring id,
completion ring id and a statistics context. Once a ring group is
initialized, use this group index while creating the rings in the ASIC
using the appropriate HWRM API added via earlier patches.
Functions added:
bnxt_free_cp_ring
Calls the HWRM function generic ring free with arguments specific
to a completion ring and sanitizes the host completion structure
bnxt_free_all_hwrm_rings
Frees all the HWRM allocated hardware rings
bnxt_free_all_hwrm_resources
Frees all the resources allocated via the HRM in the hardware
bnxt_alloc_hwrm_rings
Allocates all the HWRM rings needed in the current configuration
This should be the last functionality needed to add start/stop
device operations.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
New HWRM call:
bnxt_clear_hwrm_vnic_filters
This patch adds code to set and clear L2 filters from the
corresponding VNIC. These filters will determine the Rx flows
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add function and associated structures and definitions to free
statistics context from the ASIC.
New HWRM call:
bnxt_hwrm_stat_ctx_free
This command is used to free a stat context.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add HWRM API for ring group alloc/free functions, associated structs and
definitions.
This API allocates and does basic preparation for a ring group in ASIC.
A ring group is identified by an index. It consists of Rx ring id,
completion ring id and a statistics context.
New HWRM calls:
bnxt_hwrm_ring_grp_alloc
Allocates and does basic preparation for a ring group
bnxt_hwrm_ring_grp_free
Frees and does cleanup resources of a ring group
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add HWRM API calls to allocate and free TX, RX and Completion rings
in the hardware along with the associated structs and definitions.
This informs the hardware of how the specific rings were set up in the
host and allocates them in the HWRM, setting up the doorbell registers
etc. as needed, returning an ID for the ring.
Basic ring alloc/free calls:
bnxt_hwrm_ring_alloc
This command allocates and does basic preparation for a ring.
bnxt_hwrm_ring_free
This command is used to free a ring and associated resources.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add HWRM API code to allocate a statistics context in the ASIC.
This API will be called by the previously submitted "add statistics
operations patch".
New HWRM call:
bnxt_hwrm_stat_ctx_alloc:
This command allocates and does basic preparation for a stat
context.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add API to set/clear L2 Rx mask.
New HWRM calls:
bnxt_hwrm_cfa_l2_clear_rx_mask
bnxt_hwrm_cfa_l2_set_rx_mask
These HWRM APIs allow setting and clearing of Rx masks in L2 context
per VNIC.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
New HWRM call:
bnxt_hwrm_vnic_rss_cfg:
Used to enable RSS configuration of the VNIC.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch adds APIs to allow configuration of a VNIC.
The functions alloc and free the Class of Service or COS and
Load Balance context corresponding to the VNIC in the chip.
New HWRM calls:
bnxt_hwrm_vnic_ctx_alloc:
Used to allocate COS/Load Balance context of VNIC
bnxt_hwrm_vnic_ctx_free:
Used to free COS/Load Balance context of VNIC
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch configures the properties and actions of the VNIC
allocated by vnic_alloc function from the previous patch.
bnxt_hwrm_vnic_cfg:
Configure the VNIC structure in hardware.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
In this patch we add a new HWRM API to free a VNIC.
New HWRM call:
bnxt_hwrm_vnic_free:
Frees a vnic allocated by the bnxt_hwrm_vnic_alloc() function.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This requires a group info array in struct bnxt, so add that, we can save
the max size from the func_qcap response, and alloc/free in init/uninit
New HWRM call:
bnxt_hwrm_vnic_alloc:
Allocates a VNIC resource in the hardware.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add bnxt_hwrm_func_reset() function and supporting structs and macros.
New HWRM calls:
bnxt_hwrm_func_reset:
This command puts the function into the reset state.
In the reset state, global and port related features of the
chip are not available.
This command resets a hardware function (PCIe function) and
frees any resources used by the function. This command initiated by
the driver prepare the function for re-use. This command may also be
initiated by a driver prior to doing it's own configuration.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Perform allocation and free()ing of ring and information structures
for the TX, RX, and completion rings. The previous patches had
so far provided top level stubs and generic ring support, while this
patch does the real allocation and freeing of the memory specific to
each different type of generic ring.
For example bnxt_init_tx_ring_struct() or bnxt_init_rx_ring_struct() is
now allocating memory based on the socked_id being provided.
bnxt_tx_queue_setup_op() or bnxt_rx_queue_setup_op() have gone through
some reformatting to perform a graceful cleanup in case memory
allocation fails.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch adds initial implementation of rx_pkt_burst() function for Rx.
bnxt_recv_pkts() is the top level function for doing Rx.
This patch also adds code to allocate rings in the ASIC.
For each Rx queue allocated in the PMD driver, a corresponding ring
in hardware will be created. Every time a frame is received a Rx ring
is selected based on the hardware configuration like RSS, MAC or VLAN,
COS and such. The hardware uses a completion ring to indicate the
availability of a packet.
This patch also brings in functions like bnxt_init_one_rx_ring()
bnxt_init_rx_ring_struct() which initializes various structures before
a Rx can begin.
bnxt_init_rxbds() initializes the Rx Buffer Descriptors while
bnxt_alloc_rx_data() allocates a buffer in the host to receive the
incoming packet.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Initial implementation of tx_pkt_burst for transmit.
bnxt_xmit_pkts() is the top level function that is called during Tx.
bnxt_handle_tx_cp() is used to check and process the Tx completions
generated for the Tx Buffer Descriptors sent by the hardware.
This patch also adds code to allocate rings in the hardware.
For each Tx queue allocated in the PMD driver, a corresponding ring
in hardware will be created. Every time a Tx request is initiated
via the bnxt_xmit_pkts() call, a Buffer Descriptor is created and
is sent to the hardware via the associated Tx ring.
On completing the Tx operation, the hardware will generates the status
in the form of a completion. This completion is processed by the
bnxt_handle_tx_cp() function.
Functions like bnxt_init_tx_ring_struct() and bnxt_init_one_tx_ring()
are used to initialize various members of the structure before
starting Tx operations.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add the bnxt_stats_get_op() and bnxt_stats_reset_op() dev_ops to
get and reset statistics. It also brings in the associated HWRM calls
to handle the requests appropriately.
We also have the bnxt_free_stats() function which will be used in the
follow on patches to free the memory allocated by the driver for
statistics.
New HWRM calls:
bnxt_hwrm_stat_clear:
This command clears statistics of a context
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
In this patch we are adding the bnxt_rx_queue_setup_op() and
bnxt_rx_queue_release_op() functions. These will be tied to the
rx_queue_setup and rx_queue_release dev_ops in a subsequent patch.
In these functions we allocate/free memory for the RX queues.
This still requires support to create a RX ring in the ASIC which
will be completed in a future commit. Each Rx queue created via the
rx_queue_setup dev_op will have an associated Rx ring in the hardware.
The Rx logic in the hardware picks a Rx ring for each Rx frame received
by the hardware depending on the properties like RSS, MAC and VLAN
settings configured in the hardware. These packets in the end arrive
on the Rx queue corresponding to the Rx ring in the hardware.
We are also adding some functions like bnxt_mq_rx_configure()
bnxt_free_rx_mbufs() and bnxt_free_rxq_stats() which will be used in
subsequent patches.
We are also adding hwrm_vnic_rss_cfg_* structures, which will be used
in subsequent patches to enable RSS configuration.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
In this patch we are adding the bnxt_tx_queue_setup_op() and
bnxt_tx_queue_release_op() functions. These will be tied to the
tx_queue_setup and tx_queue_release dev_ops in a subsequent patch.
In these functions we allocate/free memory for the TX queues.
This still requires support to create a TX ring in the ASIC which
will be completed in a future commit. Each Tx queue created via the
tx_queue_setup dev_op will have an associated Tx ring in the hardware.
A Tx request coming on the Tx queue gets sent to the corresponding
Tx ring in the ASIC for subsequent transmission.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add the L2 filter structure and the alloc/init/free functions for
dealing with them.
A filter is used to identify traffic that contains a matching set of
parameters like unicast or broadcast MAC address or a VLAN tag amongst
other things which then allows the ASIC to direct the incoming traffic
to an appropriate VNIC or Rx ring.
New HWRM calls:
bnxt_hwrm_clear_filter:
Free a L2 filter.
bnxt_hwrm_set_filter
Allocate an An L2 filter or a L2 context.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Structures, macros, and functions for working with completion rings
in the driver.
Completion Ring is used by the Ethernet controller to provide the
status of transmitted & received packets, report errors, report
status changes to the host software, and inter-function forwarding
requests. In addition to the generic ring features, a completion ring
can have a statistics context that has statistics periodically DMAed
to host memory, along with a consumer index.
bnxt_handle_async_event() handles completions not related to a specific
transmit or receive ring such as link status changes which arrive on
the default completion ring.
Other physical or virtual functions on the same device may send an HWRM
command forward request. In this case, we will pass it through
unvalidated. In the future, we will be able to have the PF monitor and
control VF access to the HWRM interface if needed.
New HWRM Calls:
bnxt_hwrm_exec_fwd_resp:
Execute an encapsulated command and forward the response.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Declare generic ring structures and a free() function. These are
generic ring management functions which will be used to create Tx,
Rx and Completion rings in the subsequent patches, and tie them to
the HWRM managed ring resources.
This generic ring structure is shared all the ring types and tracks
the the host Buffer Descriptors (BDs) and the HWRM assigned ID.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add functions to allocate, initialize, and free vnics.
A VNIC represents a virtual interface. It is a resource in the RX path
of the chip and is used to setup various target actions such as RSS,
MAC filtering etc. for the physical function in use.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
The dev_configure_op function calls bnxt_set_hwrm_link_config() to
setup the PHY. This calls the new bnxt_parse_eth_link_*() functions
to translate from the DPDK macro values to those used by HWRM calls,
then calls bnxt_hwrm_port_phy_cfg() to issue the HWRM call.
New HWRM calls:
bnxt_hwrm_port_phy_cfg:
This command configures the PHY device for the port.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Gets device info from the bp structure filled in the init() function.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Move init() cleanup into uninit() function
Fix .dev_private_size
New HWRM calls:
bnxt_hwrm_func_driver_register:
This command is used by the function driver to register
its information with the HWRM.
bnxt_hwrm_func_driver_unregister:
This command is used by the function driver to unregister
with the HWRM.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Start adding support to use the HWRM API.
Hardware Resource Manager or HWRM in short, is a set of API provided
by the firmware running in the ASIC to manage the various resources.
Initial commit just performs necessary HWRM queries for init, then
fails as before.
Now that struct bnxt is non-zero size, we can set dev_private_size
correctly.
The used HWRM calls so far:
bnxt_hwrm_func_qcaps:
This command returns capabilities of a function.
bnxt_hwrm_ver_get:
This function is called by a driver to determine the HWRM
interface version supported by the HWRM firmware, the
version of HWRM firmware implementation, the name of HWRM
firmware, the versions of other embedded firmwares, and
the names of other embedded firmwares, etc. Gets the
firmware version and interface specifications. Returns
an error if the firmware on the device is not supported
by the driver and ensures the response space is large
enough for the largest possible response.
bnxt_hwrm_queue_qportcfg:
This function is called by a driver to query queue
configuration of a port.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This patch adds the initial skeleton for bnxt driver along with the
nic guide, and ties the driver into the build system.
At this point, the driver simply fails init.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
[Release Note Addition]
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
