For 25G devices auto link update was disabled because it was causing
link issues when enabled.
The problem found because of interface changes in admin queue command
"set_phy_config" and "get_phy_capabilities" for 25G.
This patch fixes the issue and enables auto link update for 25G devices.
Fixes: 75d133dd3296 ("net/i40e: enable 25G device")
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
MAC-PHY desync may occur causing misdetection of link up event.
Disabling K1-off feature can work around the problem.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This works around a possible stalled packet issue, which may occur due to
clock recovery from the PCH being too slow, when the LAN is transitioning
from K1 at 1G link speed.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
For I217 revision 6, when entering Ultra Low Power (ULP) we need to enable
Low Power Link Up (LPLU) and disable Gig speed to make it work.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
LANPHYPC low duration of 10 usec was too low for some corner cases
causing interface mismatches during Ultra Low Power (ULP) exit.
This patch increases the LANPHYPC low duration to 1 msec.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
There are some client PHY Ultra Low Power (ULP) register bits that are
configured by the Manageability Engine (ME) FW.
The driver must ensure that these bits are cleared on exit from ULP.
Ordinarily the ME FW would do that, but there are cases in which the
FW is not present, and the driver must handle that.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
When Ultra Low Power (ULP) enabled, the client PHY needs to be set up
for link configuration after cable reconnected.
Previously link configuration was only done in auto-negotiate mode.
Do link configuration also in autoneg disabled mode.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Add definition MAX_RX_JUMBO_FRAME_SIZE for igb.
All igb parts (82575 and newer) have 9.5K max jumbo frame size.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
I354 support was missing in the e1000_get_fw_version() which resulted in
the FW version not being reported. Support added.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
The driver shouldn't give up if it fails to get the hardware mailbox lock.
This can happen in a situation where the PF-VF communication channel is
heavily loaded and causes complete communications failure between the PF
and VF drivers.
Add a counter and a delay. The driver will now retry ten times,
waiting one millisecond between retries.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
With new hardware (I219), Ultra Low Power (ULP) exit takes significantly
longer time. Therefore, driver must wait longer.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Some virtual pmds report a different name than the vdev driver name
registered in eal.
While it does not hurt, let's try to be consistent.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Since commit b1fb53a39d88 ("ethdev: remove some PCI specific handling"),
rte_eth_dev_info_get() relies on dev->data->drv_name to report the driver
name to caller.
Having the pmds set driver_info->driver_name in the pmds is useless,
since ethdev overwrites it right after.
The only thing the pmd must do is:
- for pci drivers, call rte_eth_copy_pci_info() which then sets
data->drv_name
- for vdev drivers, manually set data->drv_name
At this stage, virtio-user does not properly report a driver name (fixed in
next commit).
Signed-off-by: David Marchand <david.marchand@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Jan Blunck <jblunck@infradead.org>
We can leave the title completion queue entry untouched since its contents
are not modified.
Reported-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Completion queue entry data uses network endian, to access them we should
use ntoh*().
Fixes: c305090bbaf8 ("net/mlx5: replace countdown with threshold for Tx completions")
Reported-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The list of segments to free was wrongly manipulated ending by only freeing
the first segment instead of freeing all of them. The last one still
belongs to the NIC and thus should not be freed.
Fixes: a1bdb71a32da ("net/mlx5: fix crash in Rx")
Reported-by: Liming Sun <lsun@mellanox.com>
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The offsets used in rte_i40evf_stats_strings for transmission
statistics were wrong, returning the total byte count rather than
the respective (unicast, multicast, broadcast, drop, & error)
packet counts.
Fixes: da61cd084976 ("i40evf: add extended stats")
Signed-off-by: Remy Horton <remy.horton@intel.com>
Acked-by: Kevin Traynor <ktraynor@redhat.com>
When CONFIG_RTE_VIRTIO_USER is disabled (default on FreeBSD),
the virtio driver cannot be compiled:
librte_pmd_virtio.a(virtio_ethdev.o): In function `eth_virtio_dev_init':
(.text+0x1eba): undefined reference to `virtio_user_ops'
Reported-by: Andrew Rybchenko <arybchenko@solarflare.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
This patch enhances the ethtool example to support to show
firmware version, in the same way that the Linux kernel
ethtool does.
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds a new function eth_igb_fw_version_get.
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds a new API 'rte_eth_dev_fw_version_get' for
fetching firmware version by a given device.
Signed-off-by: Qiming Yang <qiming.yang@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
When the virtio PMD is used on top of a vhost that does not support
offloads, Rx offload capabilities are still advertised by
virtio_dev_info_get(). But if an application tries to start the PMD with
Rx offloads enabled (rxmode.hw_ip_checksum = 1), the initialization of
the device will fail with -ENOTSUP and the following log:
rx ip checksum not available on this host
This patch fixes the Rx offload capabilities returned by
virtio_dev_info_get() to be consistent with features advertised by the
host.
Fixes: 96cb6711939e ("net/virtio: support Rx checksum offload")
Fixes: 86d59b21468a ("net/virtio: support LRO")
Cc: stable@dpdk.org
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Last changes in Niantic and Fortville NIC drivers causes that
vector Rx path is chosen by default in l3fwd-thread application.
This path doesn't support propagation of hw packet type recognition
to the packet_type field in mbuf, and packets cannot be classified
properly.
The approach to solve this problem is similar to the commit:
71a7e2424e07 ("examples/l3fwd: fix using packet type blindly").
To use sw packet analyzer, new command line option "--parse-ptype" is
introduced.
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
This commit add to CLI command check for the following errors
1. SVLAN and CVLAN IDs greater than 12 bits
2. MPLS ID greater than 20 bits
3. max number of supported MPLS labels to avoid array overflow
It prevents running CLI commands with invalid parameters.
Signed-off-by: Anand B Jyoti <anand.b.jyoti@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
A dollar sign is missing and it is not needed because of VPATH.
Reported-by: Ilya V. Matveychikov <matvejchikov@gmail.com>
Suggested-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Avoid the use of several strncpy() since getopt is able to
map a long option with an id, which can be matched in the
same switch/case than short options.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Do the same than in l3fwd to avoid strcmp() for long options.
For l2fwd, there is no long option that take advantage of this new
mechanism as --mac-updating and --no-mac-updating are directly setting a
flag without needing an entry in the switch/case.
So this patch just prepares the framework in case a new long option is
added in the future.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
A referenced document in the Linux Kernel has been moved to a
sub-directory. And kernel community has moved to RST/Sphinx. The links are
replaced with HTML rendered links.
Signed-off-by: Yongseok Koh <yskoh@mellanox.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
L3 Forwarding sample app user guides have some inconsistencies
between the example command line and the configuration table.
Also, they were showing too complicated configuration, using two
different NUMA nodes for two ports, which will probably lead
to performance drop due to use cross-socket channel.
This patch simplifies the configuration of these examples,
by using a single NUMA node and a single queue per port.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
This patch fixes a trivial typo in testpmd application guide.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Some CLIs don't check the input port ID, it
may cause segmentation fault (core dumped).
Fixes: 425781ff5afe ("app/testpmd: add ixgbe VF management")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Signed-off-by: Chen Jing D(Mark) <jing.d.chen@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch optimizes rte_memcpy for well aligned cases, where both
dst and src addr are aligned to maximum MOV width. It introduces a
dedicated function called rte_memcpy_aligned to handle the aligned
cases with simplified instruction stream. The existing rte_memcpy
is renamed as rte_memcpy_generic. The selection between them 2 is
done at the entry of rte_memcpy.
The existing rte_memcpy is for generic cases, it handles unaligned
copies and make store aligned, it even makes load aligned for micro
architectures like Ivy Bridge. However alignment handling comes at
a price: It adds extra load/store instructions, which can cause
complications sometime.
DPDK Vhost memcpy with Mergeable Rx Buffer feature as an example:
The copy is aligned, and remote, and there is header write along
which is also remote. In this case the memcpy instruction stream
should be simplified, to reduce extra load/store, therefore reduce
the probability of load/store buffer full caused pipeline stall, to
let the actual memcpy instructions be issued and let H/W prefetcher
goes to work as early as possible.
This patch is tested on Ivy Bridge, Haswell and Skylake, it provides
up to 20% gain for Virtio Vhost PVP traffic, with packet size ranging
from 64 to 1500 bytes.
The test can also be conducted without NIC, by setting loopback
traffic between Virtio and Vhost. For example, modify the macro
TXONLY_DEF_PACKET_LEN to the requested packet size in testpmd.h,
rebuild and start testpmd in both host and guest, then "start" on
one side and "start tx_first 32" on the other.
Signed-off-by: Zhihong Wang <zhihong.wang@intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
As it gets killed, in SIGINT signal handler, device is not stopped
and closed. In virtio's case, vector assignment in the KVM is not
deassigned.
This patch will invoke dev_stop() and dev_close() in signal handler.
Fixes: d7937e2e3d12 ("power: initial import")
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
To support those devices that do not provide packet type info when
receiving packets, add a new option, --parse-ptype, to analyze
packet type in the Rx callback.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
When closing virtio devices, close eventfds, free the struct to
store queue/irq mapping.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Tested-by: Lei Yao <lei.a.yao@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
